Add a separate field which exports tracer pid and add a new keyword
("tracer") for ps to display it.
This is a follow up to r270444.
Reviewed by: kib
MFC after: 1 week
Relnotes: yes
but has some retries.
Without this, single frame transmission in AMPDU will always look like
it succeeded fine, and thus AMRR will think it's totally fine to just
keep upping the rate upwards.
Now, this is still not quite right! For multi-frame aggregates the
completion happens in two parts - the TX done and the BA received.
The driver is currently double accounting those a little - there's no
way to say to the rate control code "I completed X frames, Y worked fine,
there were Z retries." And it's a bit odd with iwn, as the firmware
retransmits frames for us so we don't get to see how many retransmits
happened; only that it took longer than normal. I may have to extend
the rate control API to properly track that.
So this may keep the rate lower than it should be, but that's better
than keeping it higher than it should be.
Tested:
* 5100, STA mode
in preparation for the 5300 3x3 NIC.
During this particular adventure, I did indeed discover that a whole
swath of things made little to no sense.
Those included, and are fixed here:
* A lot of the antenna configuration bits assume the NIC has two receive
chains. That's blatantly untrue for NICs that don't.
* There was some disconnect between the antenna configuration when
forming a PLCP rate DWORD (which includes the transmit antenna
configuration), separate to the link quality antenna configuration.
So now there's helper functions to return which antenna configurations
to use and those are used wherever an antenna config is required.
* The 5300 does up to three stream TX/RX (so MCS0->23), however
the link quality table has only 16 slots. This means all of the
rate entries are .. well, dual-stream rates. If this is the case,
the "last MIMO" parameter can't be 16 or it panics the firmware.
Set it to 15.
* .. and since yes it has 16 slots, it only would try retransmitting
from MCS8->MCS23, which can be quite .. terrible. Hard-code the last
two retry slots to be the lowest configured rate.
* I noticed some transmit configuration command stuff is different
based on firmware API version, so I lifted that code from Linux.
* Add / augment some more logging to make it easier to capture this
stuff.
Now, 3x3 is still terrible because the link quality configuration is
plainly not good enough. I'll have to think about that.
However, the original goal of this - 3x3 operation on the Intel
5300 NIC - actually worked.
There are also rate control bugs in the way this driver handles
notifying the net80211 rate control code when AMPDU is enabled.
It always steps the rate up to the maximum rate possible - and
this eventually ends in much sadness. I'll fix that later.
As a side note - 2GHz HT40 now works on all the NICs I have tested.
As a second side note - this exposed some bad 3x3 behaviour in
the ath(4) rate control code where it starts off at a 3-stream rate
and doesn't downgrade quickly enough. This makes the initial
dhcp exchange take a long time. I'll fix the ath(4) rate code
to start at a low fixed 1x1 MCS rate and step up if everything
works out.
Tested:
* Intel 2200
* Intel 2230
* Intel 5300
* Intel 5100
* Intel 6205
* Intel 100
TODO:
* Test the other NICs more thoroughly!
Thank you to Michael Kosarev <russiane39@gmail.com> for donating the
Intel 5300 NIC and pestering me about it since last year to try and
make it all work.
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
There were two issues:
1. The area given to vt_is_cursor_in_area() was adding the drawable
area offset, something already handled by this function.
2. The cursor was shifted on the screen by the offset of this area
and thus was misplaced or not erased. Furthermore, when reaching
the bottom or right borders, the cursor was either totally
removed or not erased correctly.
MFC after: 1 week
hardware driver update from Mellanox Technologies.
- Remove empty files from the OFED Linux Emulation layer.
- Fix compile warnings related to printf() and the "%lld" and "%llx"
format specifiers.
- Add some missing 2-clause BSD copyrights.
- Add "Mellanox Technologies, Ltd." to list of copyright holders.
- Add some new compatibility files.
- Fix order of uninit in the mlx4ib module to avoid crash at unload
using the new module_exit_order() function.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The timer is restarted whenever a window buffer is marked as dirty or
the mouse cursor moves.
There's still room for improvement. For instance, we should not mark a
window buffer as dirty when this window isn't displayed.
Review: https://reviews.freebsd.org/D683
Reviewed by: ray@
Approved by: ray@
MFC after: 1 week
If DDB is active, we can't use a taskqueue thread to switch away from
the X window, because this thread can't run.
Reviewed by: ray@
Approved by: ray@
MFC after: 1 week
They are used when a panic occurs or when entering a DDB session for
instance.
cngrab() forces a vt-switch to the console window, no matter if the
original window is another terminal or an X session. However, cnungrab()
doesn't vt-switch back to the original window currently.
MFC after: 1 week
With the current implementation, this allows an X11 server to tell
the console it switches a particular window in "graphics mode". This
information is used by the mouse handling code to ignore sysmouse events
in the window taken by the X server: only him should receive those
events.
Reported by: flo@, glebius@, kan@
Tested by: flo@
Reviewed by: kan@
MFC after: 1 week
... not just the visible part.
This fixes a bug where, when switching from eg. vt_vga to vt_fb (ie. the
resolution goes up), the originally hidden, uninitialized area of the
buffer is displayed on the screen. This leads to a missing text cursor
when it's over an unitialized area.
This was also visible when selecting text: the uninitialized area was
not highlighted.
Internally, this area was zeroed: characters were all 0x00000000,
meaning the foreground and background color was black. Now, everything
is filled with a space with a gray foreground color, like the visible
area.
While here, remove the check for the mute flag and always use
TERMINAL_NORM_ATTR as the character attribute (ie. gray foreground,
black background).
MFC after: 1 week
"vm_paging_target() > 0" was a reasonable way of determining if the
inactive queue scan met its target. However, now that other threads
can be allocating pages while the inactive queue scan is running, it's
an unreliable method. The effect of it being unreliable is that we
can start swapping out processes when we didn't intend to.
This issue has existed since the kernel was multithreaded, but the
changes to the inactive queue target in 10.0-RELEASE have made its
effects visible.
This change introduces a more direct method for determining if the
inactive queue scan met its target that is not affected by the actions
of other threads.
Reported by: Steve Polyack
Tested by: pho, Steve Polyack (an earlier version)
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
This allows backends to verify they do not draw outside of this area.
This fixes a bug in vt_vga where the text was happily drawn over the
right and bottom margins, when using the Gallant font.
MFC after: 1 week
... not the whole screen. Don't use font offsets in
vt_mark_mouse_position_as_dirty().
This fixes a bug where the mouse position wasn't marked as dirty when
approaching the borders of the drawn area.
MFC after: 1 week
for dirhash cache, setting a target percent to reclaim (exposed via
SYSCTL). This allows to always make some amount of progress keeping the maximum
reclaim age dynamic.
Tested by: pho
Reviewed by: jhb
This fixes a "General protection fault" in vt_vga, where
vt_is_cursor_in_area() erroneously reported that the cursor was over the
text. This led to negative integers stored in "unsigned int" and chaos.
MFC after: 1 week
add opregion handling for drm2 - which exposes some ACPI video configuration
pieces that some Lenovo laptop models use to flesh out which video device
to speak to. This enables the brightness control in ACPI to work these models.
The CADL bits are also important - it's used to figure out which ACPI
events to hook the brightness buttons into. It doesn't yet seem to work
for me, but it does for the OP.
Tested:
* Lenovo X230 (mine)
* OP: ASUS UX51VZ
PR: 190186
Submitted by: Henry Hu <henry.hu.sh@gmail.com>
Reviewed by: dumbbell
tracepoints would continue to generate traps, which would be ignored but
could consume noticeable amounts of CPU if, say, all functions in the kernel
were instrumented.
X-MFC-With: r270067
pre-r270321. Namely, the flags are preserved for SIG_DFL and SIG_IGN
dispositions.
Requested and reviewed by: jilles
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
It's replaced by vd_bitblt_text_t, which gives more context to the
backend and allows it to perform more efficiently when redrawing a given
area.
MFC after: 1 week
Traced processes always have the tracer set as the parent.
Utilize proc_realparent to obtain the right process when needed.
Reviewed by: kib
MFC after: 1 week
Previously they were uncoditionally reparented to init. In effect
it was possible that tracee was never returned to original parent.
Reviewed by: kib
MFC after: 1 week
tunables to modify the default cpu topology advertised by bhyve.
Also add a tunable "hw.vmm.topology.cpuid_leaf_b" to disable the CPUID
leaf 0xb. This is intended for testing guest behavior when it falls back
on using CPUID leaf 0x4 to deduce CPU topology.
The default behavior is to advertise each vcpu as a core in a separate soket.
the vcpu had no caches at all. This causes problems when executing applications
in the guest compiled with the Intel compiler.
Submitted by: Mark Hill (mark.hill@tidalscale.com)
to get upset.
The Qualcomm Atheros reference design code goes through significant
hacks to shut down RX before TX. It doesn't even try do do it in the
driver - it actually makes the DMA stop routines in the HAL shut down
RX before shutting down TX.
So, to make this work for chips that aren't the AR9380 and later, do
it in the driver. Shuffle the TX stop/drain HAL calls to be called
*after* the RX stop HAL call.
Tested:
* AR5413 (STA)
* AR5212 (STA)
* AR5416 (STA)
* AR9380 (STA)
* AR9331 (AP)
* AR9341 (AP)
TODO:
* test ar92xx series NIC and the AR5210/AR5211, in case there's something
even odder about those.
aborted, allowing other threads to run. Without this change thread is just
rescheduled again, that was illustrated by provided test tool.
PR: 192926
Submitted by: eric@vangyzen.net
MFC after: 2 weeks
There were situations where the cursor was not erased/redrawn or its
position was marked as dirty even though it's not displayed. The code is
now more straightforward.
At the same, add a function to determine if the cursor covers a given
area. This is used by backends to know if they need to draw the cursor.
This new function should be paired with a new state in struct vt_device,
called vd_mshown, which indicates if the cursor should be displayed.
This again simplifies vd_bitblt_text_t callback's API.
MFC after: 1 week
variable, and don't store in autofs_mount. Also rename it from 'sc'
to 'autofs_softc', since it's global and extern.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
In textmode, no font is loaded, thus the page fault in
vt_mark_mouse_position_as_dirty() when it wants the font width/height.
For now, create a fake area for the textmode. This needs to be modified
if vt_vga gains mouse support in textmode.
While here, fix a build failure when SC_NO_CUTPASTE is defined:
vt_mark_mouse_position_as_dirty() must not be included in this case.
MFC after: 1 week
This fixes a bug where vga_get_cp437() was called with an invalid
argument. The screen was then filled with '?' instead of the actual
character.
MFC after: 1 week
v1.0.1 2014-8-19
* Do not retry the command and reset the disk when failed to enable or
disable spin up feature.
* Fix up a bug that disk failed to probe if driver failed to access the
10th LBA.
* Fix a bug that request timeout but it has been completed in certain
cases.
* Support smartmontool for R750.
Many thanks to HighPoint for continued support of FreeBSD!
MFC after: 3 days
handling ioctls. While here, remove duplicated checks for a NULL ifp in
in6_control(): this check is already done near the beginning of the
function.
PR: 189117
Reviewed by: hrs
MFC after: 2 weeks
is found, the first usable address is returned for legacy ioctls like
SIOCGIFBRDADDR, SIOCGIFDSTADDR, SIOCGIFNETMASK and SIOCGIFADDR.
While there also fix a subtle issue that a caller from a jail asking for
INADDR_ANY may get the first IP of the host that do not belong to the jail.
Submitted by: glebius
Differential Revision: https://reviews.freebsd.org/D667
- It was decided to change the driver name to if_ixl for FreeBSD
- This release adds the VF Driver to the tree, it can be built into
the kernel or as the if_ixlv module
- The VF driver is independent for the first time, this will be
desireable when full SRIOV capability is added to the OS.
- Thanks to my new coworker Eric Joyner for his superb work in
both the core and vf driver code.
Enjoy everyone!
Submitted by: jack.vogel@intel.com and eric.joyner@intel.com
MFC after: 3 days (hoping to make 10.1)
doing suspend check. This restores the pre-r251684 behaviour, to
retry once after the signal is detected.
PR: kern/192918
Submitted by: Elliott Rabe, Dell Inc., Eric van Gyzen <eric@vangyzen.net>
Obtained from: Dell Inc.
MFC after: 1 week
After some testing, it appears that acquiring the lock once and keeping
it longer is slower than taking it multiple times.
While here, fix a typo in another comment.
MFC after: 1 week
Fix some frees incorrectly assigned to M_XENBUS when the memory is
allocated with M_XENSTORE.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
dev/xen/blkback/blkback.c:
- Fix incorrect frees.
The previous global offset, based on the last loaded font, had no
meaning for other windows. This caused a shifted text area, often partly
out-of-screen.
MFC after: 1 week
This patch contains the following fixes for netback:
- Only unbind the evtchn if it has been bound.
- Set xnb->bridge to NULL after free to prevent double-freeing it.
- Set the MAC address for the host-facing interface to a dummy value.
Sponsored by: Citrix Systems R&D
dev/xen/netback/netback.c:
- Prevent trying to unbind if the evtchn has not been bounded.
- Prevent double-freeing xnb->bridge.
- Set the MAC address of the host-facing interface to a dummy value,
so it can work when the interface is added to a bridge.
This is needed so when running under Xen the calls to pci_child_added
can be intercepted and a custom Xen method can be used to register
those devices with Xen. This should not include any functional
change, since the Xen implementation will be added in a following
patch and the native implementation is a noop.
Sponsored by: Citrix Systems R&D
Reviewed by: jhb
dev/pci/pci.c:
dev/pci/pci_if.m:
dev/pci/pci_private.h:
dev/pci/pcivar.h:
- Add the pci_child_added newbus method.
that's ATAPI specific. Instead, skip to PROBE_SET_MULTI instead for
non ATAPI protocols. The prior code incorrectly terminated the probe
with a break, rather than arranging for probedone to get called. This
caused panics or worse on some systems.
This fixes a bug when two windows use different fonts, but a longer-term
solution is required. The dirty area should be stored as pixels, not
character cells, because such coordinates don't have the same meaning in
all windows, when using different fonts.
MFC after: 1 week
Compared to the deprecated vd_bitbltchr_t callback, vd_bitblt_text_t
receives:
o the whole text buffer
o the dirty area
o the mouse cursor (map, position, colors)
This allows the backend to perform optimization on how to draw things.
The goal is to remove vd_bitbltchr_t and vd_putchar_t, once all driver
are converted (only vt_vga is included in this commit).
In vt_vga, this allows to draw the text and the cursor in one pass,
without ever reading from video memory (because it has all the context).
The main benefit is the speed improvement: no more slideshow during
boot!
Other bugs fixed in vt_vga are:
o left-most characters are drawn properly (the left-most pixels were
missing with bold characters and some wide letters such as 'm')
o no more black square around the cursor
o no cursor flickering when the text is scrolling
There are still many problems to fix: the known issues are marked with
"FIXME" inside the code.
MFC after: 1 week
ignored or default, are not leaking. Apparently, there exists code
which relies on SA_SIGINFO not reported for SIG_DFL or SIG_IGN.
In kern_sigaction, ignore flags when resetting. Encapsulate the flag
and disposition testing into helper sigact_flag_test().
On exec, and when delivering signal with SA_RESETHAND flag set,
signals are reset automatically. Use new helper sigdflt(), which
removes duplicated code and corrects all flag bits for the signal.
For proc0, set sigintr bit for all ignored signals. Ignored signals
are consumed in tdsendsignal() and not delivered to the victim thread
at all.
Reported and tested by: royger
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
We haven't noticed that it was missing because eisa has been disabled for
a while in -current, but it became apparent when some parallel-build stuff
was MFC'd to 10-stable and this module failed to build there.
This provides a minor cleanup in elfdump; there are otherwise no
consumers in the tree. Old SUN documentation can be found for either
variant, but GNU binutils switched to DT_FEATURE around 2000.
Sponsored by: The FreeBSD Foundation
The goal is to clear the video memory, in case an application drew to
it. So the content shouldn't be loaded in the latches, it can't be
trusted anyway.
This improves a bit the window switch speed.
MFC after: 1 week
At the same time, "w" and "h" members are now called "width" and
"height". The goal is to have a more "public" structure, because it will
soon be passed as argument to a new callback, replacing vd_bitbltchr_t.
MFC after: 1 week
Later, we just see if the "struct mouse_cursor" pointer is set. This
avoids the need to mess with all the conditions several times; this has
been error prone.
While here, rename the variable "m" to a more meaningful "cursor", like
it's done elsewhere in the code.
MFC after: 1 week
QSFP+ data via i2c inteface. These constants has been taken
from SFF-8436 "QSFP+ 10 Gbs 4X PLUGGABLE TRANSCEIVER" standard
rev 4.8.
* Add support for printing QSFP+ information from 40G NICs
such as Chelsio T5.
This commit does not contain ioctl changes necessary for this
functionality work, there will be another commit soon.
Example:
cxl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=ec07bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,.....>
ether 00:07:43:28:ad:08
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet 40Gbase-LR4 <full-duplex>
status: active
plugged: QSFP+ 40GBASE-LR4 (MPO Parallel Optic)
vendor: OEM PN: OP-QSFP-40G-LR4 SN: 20140318001 DATE: 2014-03-18
module temperature: 64.06 C voltage: 3.26 Volts
lane 1: RX: 0.47 mW (-3.21 dBm) TX: 2.78 mW (4.46 dBm)
lane 2: RX: 0.20 mW (-6.94 dBm) TX: 2.80 mW (4.47 dBm)
lane 3: RX: 0.18 mW (-7.38 dBm) TX: 2.79 mW (4.47 dBm)
lane 4: RX: 0.90 mW (-0.45 dBm) TX: 2.80 mW (4.48 dBm)
Tested on: Chelsio T5
Tested on: Mellanox/Huawei passive/active cables/transceivers.
MFC after: 2 weeks
Sponsored by: Yandex LLC
This fixes bad looking refresh when switching window: squares instead
of text, flashing screen, and so on. In the worst case, vt_flush() came
at a very inappropriate timing and the screen was not refreshed at all
(leaving squares all over the place).
This doesn't fix the flickering of the screen with vt_vga, because the
sync signal is temporarily stopped and the video memory is cleared.
MFC after: 1 week
Like r270273, this has no effect for now, because the cursor is always
drawn. This is in preparation of future changes to vd_bitbltchr_t API.
MFC after: 1 week
Currently, this has no effect, because the cursor is always redrawn
anyway. But this will be useful after improvements to the vd_bitbltchr_t
callback API.
The vt_device structure members used to store the position of the cursor
as of the last redraw are renamed from vd_mdirty{x,y} to vd_mold{x,y}.
The associated comment is fixed too. Also, their value is now expressed
in pixels, not in character columns/row.
MFC after: 1 week
This avoids unnecessary redraw. In particular, during boot, where the
cursor is disabled and its fake position is [0;0], this triggered a
refresh of the whole screen each time vt_flush() is called.
MFC after: 1 week
Before the global flag was set/unset using the CONS_MOUSECTL ioctl, and
the per-window flag through the MOUSE_SETLEVEL or MOUSE_SETMODE ioctls.
Also, if the cursor is already enabled/disabled, return immediatly. This
avoids to reset the cursor's position to the center of the screen.
This matches syscons' behavior.
While here, remove a trailing space and a redundant variable
declaration.
that's only mostly similar. Specifically word 78 bits are defined for
IDENTIFY DEVICE as
5 Supports Hardware Feature Control
while a IDENTIFY PACKET DEVICE defines them as
5 Asynchronous notification supported
Therefore, only pay attention to bit 5 when we're talking to ATAPI
devices (we don't use the hardware feature control at this time).
Ignore it for ATA devices. Remove kludge that papered over this issue
for Samsung SATA SSDs, since Micron drives also have the bit set and
the error was caused by this bad interpretation of the spec (which is
quite easy to do, since bits aren't normally overlapping like this).
. interrupt storm detected on "intr70:"; throttling interrupt source;
. Added access serialization on iicbus_transfer(), previously there was
no such protection and a new transfer could easily confuse the
controller;
. Add error checkings (i.e. stop the transfer when a error is detected
and do _not_ overwrite the previous error);
. On command done interrupt do not assume that the transfer was finished
sucessfully as we will receive the command done interrupt even after
errors;
. Simplify the FIFO handling;
. Reset the FIFO between the transfers as the FIFO may contain data from
the last (failed) transfer;
. Fix the iicbus speed for AM335x, which in turn will make better use of
the I2C noise filter (set to one internal clock cycle);
. Move the read and write handler to ithread instead of notifying the
requesting thread with wakeup(9);
. Fix the comments based on OMAP4 TRM.
The above changes allows me to read the EDID from my HDMI monitor on BBB
with gonzo's patches to support TDA19988 (which does 128 bytes reads) and
repeatedly scan the iicbus (with a modified i2c(8)) without lock up the bus.
Phabric: D465
This should not be an ABI change since the various public APIs that use
cpusets all include an explicit size parameter in addition to the cpuset
parameter.
MFC after: 1 week
This is (yet another) step towards the removal of device
cloning from our kernel.
CR: https://reviews.freebsd.org/D441
Reviewed by: kib, rwatson
Tested by: pho
Make the functions pci_disable_msi, pci_enable_msi and pci_enable_msix
methods of the newbus PCI bus. This code should not include any
functional change.
Sponsored by: Citrix Systems R&D
Reviewed by: imp, jhb
Differential Revision: https://reviews.freebsd.org/D354
dev/pci/pci.c:
- Convert the mentioned functions to newbus methods.
- Fix the callers of the converted functions.
sys/dev/pci/pci_private.h:
dev/pci/pci_if.m:
- Declare the new methods.
dev/pci/pcivar.h:
- Add helpers to call the newbus methods.
ofed/include/linux/pci.h:
- Add define to prevent the ofed version of pci_enable_msix from
clashing with the FreeBSD native version.
I've decided that for 11n rates it's best to start (very) low and work
our way up.
So, from now on, the initial rate for AMRR 11n is MCS4.
It doesn't try MCS12 or MCS20 - at low signal strengths those don't
work very well at all.
AMRR will step the rate control up over time if things work out better.
Tested:
* Intel 5100
* Intel 5300 (using local diffs to test out 3x3 stream support)
kern_renameat() already starts write on the mp, which prevents
parallel unmount from proceed. Busying mp after vn_start_write()
deadlocks the unmount.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
unmount. There is no need to suspend read-only filesystem, while we
need suspension on modificable mount point.
Reported by: rwatson
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Eventually, the vmd_segs of the struct vm_domain should become bitset
instead of long, to allow arbitrary compile-time selected maximum.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
physical address of the page to direct map address, in case
SFBUF_OPTIONAL_DIRECT_MAP returns true. The case of PowerPC AIM
64bit, where the page physical address is identical to the direct map
address, is accidental.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
1. 50+% of NO_PIE use is fixed by adding -fPIC to INTERNALLIB and other
build-only utility libraries.
2. Another 40% is fixed by generating _pic.a variants of various libraries.
3. Some of the NO_PIE use is a bit absurd as it is disabling PIE (and ASLR)
where it never would work anyhow, such as csu or loader. This suggests
there may be better ways of adding support to the tree. Many of these
cases can be fixed such that -fPIE will work but there is really no
reason to have it in those cases.
4. Some of the uses are working around hacks done to some Makefiles that are
really building libraries but have been using bsd.prog.mk because the code
is cleaner. Had they been using bsd.lib.mk then NO_PIE would not have
been needed.
We likely do want to enable PIE by default (opt-out) for non-tree consumers
(such as ports). For in-tree though we probably want to only enable PIE
(opt-in) for common attack targets such as remote service daemons and setuid
utilities. This is also a great performance compromise since ASLR is expected
to reduce performance. As such it does not make sense to enable it in all
utilities such as ls(1) that have little benefit to having it enabled.
Reported by: kib
good example is socket options that aren't necessarily generic. To
this end, OSD is added to the socket structure and hooks are defined
for key operations on sockets. These are:
o soalloc() and sodealloc()
o Get and set socket options
o Socket related kevent filters.
One aspect about hhook that appears to be not fully baked is the return
semantics (the return value from the hook is ignored in hhook_run_hooks()
at the time of commit). To support return values, the socket_hhook_data
structure contains a 'status' field to hold return values.
Submitted by: Anuranjan Shukla <anshukla@juniper.net>
Obtained from: Juniper Networks, Inc.
starting with a superpage demotion by pmap_enter() that could result in
a PV list lock being held when pmap_enter() is just about to return
KERN_RESOURCE_SHORTAGE. Consequently, the KASSERT that no PV list locks
are held needs to be replaced with a conditional unlock.
Discussed with: kib
X-MFC with: r269728
Sponsored by: EMC / Isilon Storage Division
sample size. According to the USB audio frame format specification
from USB.org, the value in the "bBitResolution" field can be less than
the actual sample size, depending on the actual hardware, and should
not be used for this computation.
PR: 192755
MFC after: 1 week
header (Elf_Ehdr) to determine if a particular interpretor wants to
accept it or not. Use this mechanism to filter EABI arm on OABI arm
kernels, and vice versa. This method could also be used to implement
OABI on EABI arm kernels, if desired, or to allow a single mips kernel
to run o32, n32 and n64 binaries.
Differential Revision: https://reviews.freebsd.org/D609
UNIX systems, eg. MacOS X and Solaris. It uses Sun-compatible map format,
has proper kernel support, and LDAP integration.
There are still a few outstanding problems; they will be fixed shortly.
Reviewed by: allanjude@, emaste@, kib@, wblock@ (earlier versions)
Phabric: D523
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
duplicating the entire implementation for both x86 and powerpc. This makes
it easier to add support for other architectures and has no functional
impact.
Phabric: D613
Reviewed by: gnn, jhibbits, rpaulo
Tested by: jhibbits (powerpc)
MFC after: 2 weeks
soc-wide info lives. It was under dev.imx6_anatop.0.
What does anatop mean anyway? Nobody seems to know, so it's probably
not where somebody will think to look for imx6 hardware info.
Mostly bugfixes or features developed in the past 6 months,
so this is a 10.1 candidate.
Basically no user API changes (some bugfixes in sys/net/netmap_user.h).
In detail:
1. netmap support for virtio-net, including in netmap mode.
Under bhyve and with a netmap backend [2] we reach over 1Mpps
with standard APIs (e.g. libpcap), and 5-8 Mpps in netmap mode.
2. (kernel) add support for multiple memory allocators, so we can
better partition physical and virtual interfaces giving access
to separate users. The most visible effect is one additional
argument to the various kernel functions to compute buffer
addresses. All netmap-supported drivers are affected, but changes
are mechanical and trivial
3. (kernel) simplify the prototype for *txsync() and *rxsync()
driver methods. All netmap drivers affected, changes mostly mechanical.
4. add support for netmap-monitor ports. Think of it as a mirroring
port on a physical switch: a netmap monitor port replicates traffic
present on the main port. Restrictions apply. Drive carefully.
5. if_lem.c: support for various paravirtualization features,
experimental and disabled by default.
Most of these are described in our ANCS'13 paper [1].
Paravirtualized support in netmap mode is new, and beats the
numbers in the paper by a large factor (under qemu-kvm,
we measured gues-host throughput up to 10-12 Mpps).
A lot of refactoring and additional documentation in the files
in sys/dev/netmap, but apart from #2 and #3 above, almost nothing
of this stuff is visible to other kernel parts.
Example programs in tools/tools/netmap have been updated with bugfixes
and to support more of the existing features.
This is meant to go into 10.1 so we plan an MFC before the Aug.22 deadline.
A lot of this code has been contributed by my colleagues at UNIPI,
including Giuseppe Lettieri, Vincenzo Maffione, Stefano Garzarella.
MFC after: 3 days.
This is needed to prevent having interfaces with ifp->if_addr == NULL
on bridge interfaces. Moving the notification event handlers up makes
sure the interfaces are removed before doing any more cleanup.
Sponsored by: Citrix Systems R&D
Reviewed by: melifaro
Differential Revision: https://reviews.freebsd.org/D598
net/if.c
- Move interface removal notification up in if_detach_internal.
configure the mux and config registers for PIO devices based on what
we find in the FDT. I developed it per the spec that had been
committed to Linux in the January 2014 time frame and haven't
updated. In short, bundles of pins are activated in specific ways for
specific configurations, and we implement all of that.
What's not included is a MI device infrastructure, any dynamic
run-time changing of these pins, etc. Also not included are hooks into
all the drivers to enable the latter (static at boot no driver changes
are needed). These larger questions will need to be answered once we
have more drivers like this for more platforms, or somebody has a heck
of a lot of time to research a bunch of platforms, the Linux solution
(which is good, but has its warts), etc.
otherwise bad consequences including a routing loop can occur.
Move pf_set_rt_ifp() earlier in state creation sequence and
inline it, cutting some extra code.
PR: 183997
Submitted by: Kajetan Staszkiewicz <vegeta tuxpowered.net>
Sponsored by: InnoGames GmbH
called a scalable path. When several preconditions hold, the vm
object lock for the object containing the faulted page is taken in
read mode, instead of write, which allows parallel faults processing
in the region.
Namely, the fast path is taken when the faulted page already exists
and does not need copy on write, is already fully valid, and not busy.
For technical reasons, fast path is avoided when the fault is the
first write on the vnode object, or when the fault is for wiring or
debugger read or write.
On the fast path, pmap_enter(9) is passed the PMAP_ENTER_NOSLEEP flag,
since object lock is kept. Pmap might fail to create the entry, in
which case the fallback to slow path is performed.
Reviewed by: alc
Tested by: pho (previous version)
Hardware provided and hosted by: The FreeBSD Foundation and
Sentex Data Communications
Sponsored by: The FreeBSD Foundation
MFC after: 2 week
- Do not count global number of states and of src_nodes,
use uma_zone_get_cur() to obtain values.
- Struct pf_status becomes merely an ioctl API structure,
and moves to netpfil/pf/pf.h with its constants.
- V_pf_status is now of type struct pf_kstatus.
Submitted by: Kajetan Staszkiewicz <vegeta tuxpowered.net>
Sponsored by: InnoGames GmbH
cutover is, but we need better tools to cope with inline tuning per
compiler version than we have. This is a quick bandaid until such
tools are around.
work. This gets my AT91SAM9260-based boards almost booting with
current in multi pass. The MCI driver is broken, but it is equally
broken before multi-pass.
By Richard Earnshaw at ARM
>
>GCC has for a number of years provides a set of pre-defined macros for
>use with determining the ISA and features of the target during
>pre-processing. However, the design was always somewhat cumbersome in
>that each new architecture revision created a new define and then
>removed the previous one. This meant that it was necessary to keep
>updating the support code simply to recognise a new architecture being
>added.
>
>The ACLE specification (ARM C Language Extentions)
>(http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.set.swdev/index.html)
>provides a much more suitable interface and GCC has supported this
>since gcc-4.8.
>
>This patch makes use of the ACLE pre-defines to map to the internal
>feature definitions. To support older versions of GCC a compatibility
>header is provided that maps the traditional pre-defines onto the new
>ACLE ones.
Stop using __FreeBSD_ARCH_armv6__ and switch to __ARM_ARCH >= 6 in the
couple of places in tree. clang already implements ACLE. Add a define
that says we implement version 1.1, even though the implementation
isn't quite complete.
socket options. This includes managing the correspoing stat counters.
Add the SCTP_DETAILED_STR_STATS kernel option to control per policy
counters on every stream. The default is off and only an aggregated
counter is available. This is sufficient for the RTCWeb usecase.
MFC after: 1 week
page queue even when the allocation is not wired. It is
responsibility of the vm_page_grab() caller to ensure that the page
does not end on the vm_object queue but not on the pagedaemon queue,
which would effectively create unpageable unwired page.
In exec_map_first_page() and vm_imgact_hold_page(), activate the page
immediately after unbusying it, to avoid leak.
In the uiomove_object_page(), deactivate page before the object is
unlocked. There is no leak, since the page is deactivated after
uiomove_fromphys() finished. But allowing non-queued non-wired page
in the unlocked object queue makes it impossible to assert that leak
does not happen in other places.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
trees. This happens because the logic inserting items into the radix
tree is allocating empty radix levels, when index zero does not
contain any items.
- Add proper error case handling, so that the radix tree does not end
up in a bad state, if memory cannot be allocated during insertion of
an item.
- Add check for inserting NULL items into the radix tree.
- Add check for radix tree getting too big.
MFC after: 1 week
Sponsored by: Mellanox Technologies
r269533, which was tested before r269457 was committed, implicitely
relied on the Giant to protect the manipulations of the softdepmounts
list. Use softdep global lock consistently to guarantee the list
structure now.
Insert the new struct mount_softdeps into the softdepmounts only after
it is sufficiently initialized, to prevent softdep_speedup() from
accessing bare memory. Similarly, remove struct mount_softdeps for
the unmounted filesystem from the tailq before destroying structure
rwlock.
Reported and tested by: pho
Reviewed by: mckusick
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
instead of M_NOWAIT/M_WAITOK when deciding whether to sleep on page table
page allocation. (The same functions in the i386/xen and mips pmap
implementations already use PMAP_ENTER_NOSLEEP.)
X-MFC with: r269728
Sponsored by: EMC / Isilon Storage Division
