Allow 500us between pauses in ahd_pause_and_flushwork().
The maximum we will wait is now 500ms.
In the same routine, remove any attempt to clear ENSELO.
Let the firmware do it once the current selection has
completed. This avoids some race conditions having to
do with non-packetized completions and the auto-clearing
of ENSELO on packetized completions.
Also avoid attempts to clear critical sections when
interrups are pending. We are going to loop again
anyway, so clearing critical sections is a waste of
time. It also may not be possible to clear a critical
section if the source of the interrupt was a SEQINT.
aic79xx_pci.c:
Use the Generic 9005 mask when looking for generic 7901B
parts. This allows the driver to attach to 7901B parts
on motherboards using a non-Adaptec subvendor ID.
aic79xx_inline.h:
Test for the SCBRAM_RD_BUG against the bugs
field, not the flags field in the softc.
aic79xx.c:
Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
aic79xx.c:
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case
aic79xx.c:
Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command. This
safety measure is added in response to a timeout recovery
failure on H2B where it appears that incoming reselection
status was lost during a drive pull test. In that case,
the recovery handler continued to wait for the command
that was active on the bus indefinetly. While the root
cause of the above issue is still being determined seems
a prudent safeguard.
aic79xx_pci.c:
Add a specific probe entry for the Dell OEM 39320(B).
aic79xx.c:
aic79xx.h:
aic79xx.reg:
aic79xx.seq:
Modify the aic79xx firmware to never cross a cacheline or
ADB boundary when DMA'ing completion entries to the host.
In PCI mode, at least in 32/33 configurations, the SCB
DMA engine may lose its place in the data-stream should
the target force a retry on something other than an
8byte aligned boundary. In PCI-X mode, we do this to
avoid split transactions since many chipsets seem to be
unable to format proper split completions to continue
the data transfer.
The above change allows us to drop our completion entries
from 8 bytes to 4. We were using 8 byte entries to ensure
that PCI retries could only occur on an 8byte aligned
boundary. Now that the sequencer guarantees this by splitting
up completions, we can safely drop the size to 4 bytes (2
byte tag, one byte SG_RESID, one byte pad).
Both the split-completion and PCI retry problems only show
up under high tag load when interrupt coalescing is being
especially effective. The switch from a 2byte completion
entry to an 8 byte entry to solve the PCI problem increased
the chance of incurring a split in PCI-X mode when multiple
transactions were completed at once. Dropping the completion
size to 4 bytes also means that we can complete more commands
in a single DMA (128byte FIFO -> 32 commands instead of 16).
aic79xx.c:
Modify the SCSIINT handler to defer clearing
sequencer critical sections to the individual
interrupt handlers. This allows us to
immediately disable any outgoing selections in
the case of an unexpected busfree so we don't
inadvertantly clear ENSELO *after* a new selection
has started. Doing so may cause the sequencer
to miss a successful selection.
In ahd_update_pending_scbs(), only clear ENSELO if
the bus is currently busy and a selection is not
already in progress or the sequencer has yet to
handle a pending selection. While we want to ensure
that the selection for the SCB at the head of the
selection queue is restarted so that any change in
negotiation request can take effect, we can't clobber
pending selection state without confusing the sequencer
into missing a selection.
sequencer interrupt codes. These codes are only
relevant to the code that was last being executed
and that context is cleared when we reset the
program counter. This addresses a race condition
between a sequencer interrupt and any SCSI event
that causes us to restart the sequencer.
o When running the untagged-Q, we must start the
timer for any transaction we queue.
o Give the firmware half a millisecond between
pauses to flush work out. This should give us
around half a second of total delay before flagging
an issue with pausing and flushing controller work.
Only attempt to clear critical sections if there
are no pending interrupts in the pause and flush
loop. If the sequencer has issued an INTSTAT, we
may not be able to step out of the critical section.
o Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
o In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case.
o Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command.
are used.
- Reduce duplication of a couple of macros removing the duplicates from
ich.h.
- Remove unused macros from icu.h as well as locore protection as this
header is no longer included in assembly sources.
- Require the APIC enumerators to explicitly enable mixed mode by calling
ioapic_enable_mixed_mode(). Calling this function tells the apic driver
that the PC-AT 8259A PICs are present and routable through the first I/O
APIC via an ExtINT pin. The mptable enumerator always calls this
function for now. The MADT enumerator only enables mixed mode if the
PC-AT compatability flag is set in the MADT header.
- Allow mixed mode to be enabled or disabled via a 'hw.apic.mixed_mode'
tunable. By default this tunable is set to 1 (true). The kernel option
NO_MIXED_MODE changes the default to 0 to preserve existing behavior, but
adding 'hw.apic.mixed_mode=0' to loader.conf achieves the same effect.
- Only use mixed mode to route IRQ 0 if it is both enabled by the APIC
enumerator and activated by the loader tunable. Note that both
conditions must be true, so if the APIC enumerator does not enable mixed
mode, then you can't set the tunable to try to override the enumerator.
to map. If the checksum fails, the table is unmapped and a NULL pointer
returned.
- For ACPI version >= 2.0, check the extended checksum of the RSDP.
AcpiOsGetRootPointer() already checks the version 1.0 checksum.
- Remap the full MADT table at the end of madt_probe() so that we verify
its checksum before saying it is really there.
Requested by: njl
the swizzle method for routing PCI interrupts across the bridge. This
fixes problems with motherboards (typically laptops) whose BIOS doesn't
provide a PRT for the AGP bridge even though there is a device entry for
the bridge in the ACPI namespace.
Tested by: Kenneth Culver culverk at sweetdreamsracing dot biz
it back to userspace, so it does not break bind(2) on raw sockets in jails.
Currently some processes, like traceroute(8) construct a routing request
to determine its source address based on the destination. This sockaddr
data is fed directly to bind(2). When bind calls ifa_ifwithaddr(9) to
make sure the address exists on the interface, the comparison will
fail causing bind(2) to return EADDRNOTAVAIL if the data wasnt zero'ed
before initialization.
Approved by: bmilekic (mentor)
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.
Approved by: tmm, no objections on freebsd-sparc64
It's not quite correct from a posix Point Of view, but it is a lot better
than what was there before. This will be revisited later
when we decide what form our priority extensions will take. Posix doesn't
specify how a system scope thread can change its priority so you need to
add non-standard extensions to be able to do it..
For now make this slightly non standard to allow it to be done.
Submitted by: Dan Eischen originally, changed by myself.
there's not dependencies on pccard symboles, such a dependency is not
necessary. This means that drivers that have multiple attachments can
not drag bogus devices into the kernel at load time.
We can't (yet) do this with pci and isa. Drivers written for them
actually do seem to have symbols that depend on these busses'
implementation code.
ndis not touched until other things can be tested.
