In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
Previously only TX IP checksum offloading was disabled but it's
reported that TX checksum offloading for UDP datagrams with IP
options also generates corrupted frames. Reporter's controller is
RTL8168CP but I guess RTL8168C also have the same issue since it
shall share the same core.
Reported and tested by: tuexen
driver as version 8.037.00 for RTL8168{E-VL,EP,F,G,GU} and RTL8111B. This
makes reception of packets work with the RTL8168G (HW rev. 0x4c000000) in
my Shuttle DS47.
- Consistently use RL_MSI_MESSAGES.
In joint forces with: yongari
MFC after: 5 days
This includes the following:
- use separate memory regions for VALE ports
- locking fixes
- some simplifications in the NIC-specific routines
- performance improvements for the VALE switch
- some new features in the pkt-gen test program
- documentation updates
There are small API changes that require programs to be recompiled
(NETMAP_API has been bumped so you will detect old binaries at runtime).
In particular:
- struct netmap_slot now is 16 bytes to support an extra pointer,
which may save one data copy when using VALE ports or VMs;
- the struct netmap_if has two extra fields;
MFC after: 3 days
RTL8168GU has two variants(GMII and MII) but it uses the same chip
revision id. Driver checks PCI device id of controller and
sets internal capability flag(i.e. jumbo frame and link speed down
in WOL).
H/W donated by: RealTek Semiconductor Corp.
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
#defines. This also has the advantage that it makes the names more
compact, iand also allows us to correct the non-uniform naming of
the PCIM_LINK_* defines, making them all consistent amongst themselves.
This is a mostly mechanical rename:
s/PCIR_EXPRESS_/PCIER_/g
s/PCIM_EXP_/PCIEM_/g
s/PCIM_LINK_/PCIEM_LINK_/g
When this is MFC'd, #defines will be added for the old names to assist
out-of-tree drivers.
Discussed with: jhb
MFC after: 1 week
extract a link status of PHY when parent driver is re(4).
RGEPHY_MII_SSR register does not seem to report correct PHY status
on some integrated PHYs used with re(4).
Unfortunately, RealTek PHYs have no additional information to
differentiate integrated PHYs from external ones so relying on PHY
model number is not enough to know that. However, it seems
RGEPHY_MII_SSR register exists for external RealTek PHYs so
checking parent driver would be good indication to know which PHY
was used. In other words, for non-re(4) controllers, the PHY is
external one and its revision number is greater than or equal to 2.
This change fixes intermittent link UP/DOWN messages reported on
RTL8169 controller.
Also, mii_attach(9) is tried after setting interface name since
rgephy(4) have to know parent driver name.
PR: kern/165509
USERSPACE:
1. add support for devices with different number of rx and tx queues;
2. add better support for zero-copy operation, adding an extra field
to the netmap ring to indicate how many buffers we have already processed
but not yet released (with help from Eddie Kohler);
3. The two changes above unfortunately require an API change, so while
at it add a version field and some spares to the ioctl() argument
to help detect mismatches.
4. update the manual page for the two changes above;
5. update sample applications in tools/tools/netmap
KERNEL:
1. simplify the internal structures moving the global wait queues
to the 'struct netmap_adapter';
2. simplify the functions that map kring<->nic ring indexes
3. normalize device-specific code, helps mainteinance;
4. start exploring the impact of micro-optimizations (prefetch etc.)
in the ixgbe driver.
Use 'legacy' descriptors on the tx ring and prefetch slots gives
about 20% speedup at 900 MHz. Another 7-10% would come from removing
the explict calls to bus_dmamap* in the core (they are effectively
NOPs in this case, but it takes expensive load of the per-buffer
dma maps to figure out that they are all NULL.
Rx performance not investigated.
I am postponing the MFC so i can import a few more improvements
before merging.
RTL810x family , RTL8139 has different register map for Config
registers.
While here, follow the lead of re(4) in WOL configuration.
- Disable WOL_UCAST and WOL_MCAST capabilities by default.
- Config5 register write does not need to unlock EEPROM access
on RTL8139 family but unlocking EEPROM access does not affect
its operation and make it consistent with re(4).
Reported by: Matt Renzelmann mjr <> cs dot wisc dot edu
On my hardware, "em" in netmap mode does about 1.388 Mpps
on one card (on an Asus motherboard), and 1.1 Mpps on another
card (PCIe bus). Both seem to be NIC-limited, because
i have the same rate even with the CPU running at 150 MHz.
On the "re" driver the tx throughput is around 420-450 Kpps
on various (8111C and the like) chipsets. On the Rx side
performance seems much better, and i can receive the full
load generated by the "em" cards.
"igb" is untested as i don't have the hardware.
put into suspend/shutdown. Old PCI controllers performed that
operation in firmware but for RTL8111C or newer controllers, it's
responsibility of driver. It's not clear whether the firmware of
RTL8111B still downgrades its speed to 10/100Mbps so leave it as it
was.
Because there is no reliable way to know whether RX MAC is in
stopped state, rejecting all frames would be the only way to
minimize possible races.
Otherwise it's possible to receive frames while stop command
execution is in progress and controller can DMA the frame to freed
RX buffer during that period.
This was observed on recent PCIe controllers(i.e. RTL8111F).
While this change may not be required on old controllers it
wouldn't make negative effects on old controllers. One side effect
of this change is disabling receive so driver reprograms RL_RXCFG
to receive WOL frames when it is put into suspend or shutdown.
This should address occasional 'memory modified free' errors seen
on recent RealTek controllers.
driver would ignore the first link state update if controller
already established a link such that it would have to take
additional link state handling in re_tick().
access.
While I'm here, enable WOL through magic packet but disable waking
up system via unicast, multicast and broadcast frames. Otherwise,
multicast or unicast frame(e.g. ICMP echo request) can wake up
system which is not probably wanted behavior on most environments.
This was not known as problem because RL_CFG5 register access had
not effect until this change.
The capability to wake up system with unicast/multicast frames
are still set in driver, default off, so users who need that
feature can still activate it with ifconfig(8).
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
controllers.
More and more RealTek controllers started to implement EEE feature.
Vendor driver seems to load a kind of firmware for EEE with
additional PHY fixups. It is known that the EEE feature may need
ASPM support. Unfortunately there is no documentation for EEE of
the controller so enabling ASPM may cause more problems.
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
controller in question generates frames with bad IP checksum value
if packets contain IP options. For instance, packets generated by
ping(8) with record route option have wrong IP checksum value. The
controller correctly computes checksum for normal TCP/UDP packets
though.
There are two known RTL8168/8111C variants in market and the issue
I observed happened on RL_HWREV_8168C_SPIN2. I'm not sure
RL_HWREV_8168C also has the same issue but it would be better to
assume it has the same issue since they shall share same core.
RTL8102E which is supposed to be released at the time of
RTL8168/8111C announcement does not have the issue.
Tested by: Konstantin V. Krotov ( kkv <> insysnet dot ru )
the controller has a kind of embedded controller/memory and vendor
applies a large set of magic code via undocumented PHY registers in
device initialization stage. I guess it's a firmware image for the
embedded controller in RTL8105E since the code is too big compared
to other DSP fixups. However I have no idea what that magic code
does and what's purpose of the embedded controller. Fortunately
driver seems to still work without loading the firmware.
While I'm here change device description of RTL810xE controller.
H/W donated by: Realtek Semiconductor Corp.
