Obtained from:
sio.c and sioreg.c changed to allow autodetecting the RB_SERIAL flag
passed by the boot blocks so that the kernel can switch to 'serial
console' mode automagically. 'options COMCONSOLE' can still be specified
to force the kernel to always use the serial port as a console.
CONUNIT and CONADDR can also be specified in the kernel config file
if the user wants to shift the console to a different port.
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
properly from the beginning:
1) The `kern_devconf' struct should be a part of the driver's
`softc' structure (now it is).
2) The `description' should say what the device actually is,
rather than just giving a model number (now it does).
3) The device should be registered even if the probe fails, so
that it can be reconfigured later.
4) For netifs, the device state should follow the IFF_UP flag.
Other network interfaces should follow this example. (Please?) Eventually
there should be a rundown routine doing the equivalent of setting IFF_UP
off, and perhaps more if warranted.
protected drive at open() time has been *totally bogus*! The guy who
submitted it didn't understand all the implications of calling
set_motor(), and the `who' who included the patch into the tree did it
blindly... Pleeeeze, don't commit code to this driver unless you are
really going to understand what it does! This one caused me to pull
out even more hears, and those who know me do know that i ain't got
too many o'them. :-)
No kernel config options anymore besides keyboard language layout.
Virtual consoles are now dynamically allocated, no NCONS anymore.
Software cursor blinking/nonblinking.
Visual bell for laptops (don't beep at meetings :-).
Cursor/bell default type setable via config "flags" instead of as defines.
Cursor/bell type setable via ioctl's.
New video modes 80x30 80x60 for some laptops, and those with multisync monitors.
Scroll-lock history (length currently fixed at 100 lines).
Lots of cleanups, some only commented out for now (will goaway soon).
Support for new features in vidcontrol/kbdcontrol.
Updated manpages.
now marked busy as long as it's being in non-reset state, and the
drives are busy as long as at least one instance is open.
Also reformat everything to fit into 80 columns again.
Changed my mind wrt. error reporting for a write-protected drive and
an open() with write intent; ENXIO has been too weird, now return EIO.
Some portions of the code need to be rewritten to use tprintf()
instead of simple printf()'s, so the messages will also appear on the
session terminal, however.
Wangtek PC-02 QIC-02 controller with Cipher 150MB tape drive
Any attemp to open /dev/rwt0 hangs.
The following patch to /sys/i386/isa/wt.c is derived from Mikael
Hybsch's wt driver.
Submitted by: Terry Lee <terry@uivlsi.csl.uiuc.edu>
shifting. Also correct the original code as Garrett noticed it in mail.
Leave the mishandled code in to use it later if future versions of gcc
are correct. The code was part of the calibrate_cyclecounter routine to
get the speed of the pentium chip.
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.
Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.
Submitted by: (mostly) Peter Dufault <dufault@FreeBSD.org>
no more DOS boots to start it up.
Simply did a localized nuke of the OUTB macro in this file. This is
a kludge, since it seems it may actually be necessary in other GUS
files (tbd).
Thanks to: Amancio Hasty & Ken Hornstein
correct console number for the VT_WAITACTIVE ioctl. Invalid console numbers
caused waiting on an invalid pointer.
Use bcopyw() instead of move_up() and move_down(). bcopyw() handles
overlapped copies and should be faster. Actually use bcopy(). bcopy()
is slightly faster if video memory is 16-bit and about twice as fast if
it is 32-bit. bcopy() is said to fail on someGA's, but syscons already
depends on it working for other accesses to video memory.
Remove bogus input operands for fnsave(), fnstcw() and fnstsw().
Change all fwait's to fnop's. This might help avoid hardware bugs.
Wait after fninit with an fnop. This should be safer now.
Fix some spelling and formatting errors.
Use natural sizes for control and status words (u_short, promotes to int).
Don't clobber the SWI_CLOCK_MASK bits in npx0_imask when using IRQ13.
Set the devconf state correctly (always busy, if configured). Improve
code for npx_registerdev() a little (gcc can't keep id->id_unit in a
register for some reason). Don't register a nonexistent npx device.
Print a useful message in npxattach() again (delete references to errors
and not the whole message). Don't print "387 emulator" if there is no
emulator in the kernel.
Use %p for pointers in error messages.
Don't clobber the FPU state when there is an FPU exception. Just clear
the exception flags (after saving the flags as before). This allows
debuggers and SIGFPE handlers to look at the full exception state.
SIGFPE handlers should normally return via longjmp(), which restores a
good FPU state (as before). Returning from a SIGFPE handler may leave
the FPU in the wrong state (as before).
Clear the busy latch _after_ clearing the exception flags so that there
is less chance of getting a bogus h/w interrupt for a control operation.
Clear the saved exception status word when the next FPU instruction is
excuted so that it doesn't stick around until the next exception.
Clear the busy latch after fnsave() in npxsave() in case it was set when
npxsave() was called.
values for syncronous negotiation. The 284x series adaptors can now be
supported without the Bios being enabled. If you disable the Bios on the
274x series adaptors, all configuration parameters revert to the default
since there is no way to retrieve them.
- /sys/i386/isa/if_ed.c doesn't quite know how to deal with SMC EtherEZ
ethernet cards. The EtherEZ looks just like the Elite Ultra, except it
has only 8K of shared memory. The only way to have it properly detected
is to zero and test a few bytes of memory just about the first 8K region.
If it clears properly, it's an Elite Ultra, otherwise it's an EtherEZ.
I've also got an EtherEZ patch for netboot (Makefile, ether.c and ether.h).
- /sys/i386/isa/syscons.c wraps at the next to the last column rather than
the last column, like it should. You don't really notice this unless you
use certain programs that write all the way out to, say, the 80th column,
like VMSmail. Along with a one-line fix for this are some changes to
implement a non-blinking cursor. Put 'options "NOBLINK_CURSOR"' in your
config file and give it a try. :)
Submitted by: wpaul
Would you please commit this two-line patch to /sys/i386/isa/b004.c
(the Transputer driver) so that it at least compiles under 2.x
Haven't tried if the driver is working properly, but a kernel with
compiled-in driver has been running for two days now with no apparent
problems.
Submitted by: luigi
This is new version of Seagate ST01/02, Future Domain TMC-885, TMC-950
SCSI driver for FreeBSD. I started from the 2.0R version and mostly
rewrote it. New features are:
1) New probe algorithm. Old driver read the BIOS region of the adapter
memory and find the copyright string. The problem was in the BIOS itself:
it conflicted with IDE disks. The solution was to unplug it and
make the probe algorithm to work without it.
2) Proper timeout handling in numerous places where the driver
polls waiting for some event.
3) Assembler flagments added in critical places, mostly for data transfer
to of from the target. It was possible to make it faster,
but at the price of decreasing reliability.
4) Target-dependent delays when waiting for REQ deassert event.
Some devices seem to be slower (CD-ROMS, some tape drives),
and some seem to be too fast (disks). The driver tests the REQ
deassert timeout for each target and then uses it for polling.
5) Device flags added for SCSI parity control and sense request
priority control.
6) Generic cleanup, after which the driver became much more readable
(at least by me:).
7) Target data parity error logging is limited to avoid log file overflow.
8) Manual page added.
Submitted by: serge
Move definition of `stat_imask' to clock.c.
clock.c:
Rename `rtcmask' to `stat_imask' and export it. Rename `clkmask' to
`clk_imask' for consistency.
Only calculate TIMER_DIV(hz) once.
Merge debugging and "garbage" code to produce debugging code and format the
output better.
Make writertc() static inline and use it everywhere. Now all accesses to
the clock registers go through rtcin() and writertc().
Move rtc initialization to cpu_initclocks().
Merge enablertclock() with cpu_initclocks() and remove enablertclock().
The extra entry point was just a leftover from 1.1.5.
for wd (they both count the number of sectors). The wpms stat is still
moderately bogus for all drivers. Even the count stat could be handled
better (partial blocks should be counted as full blocks; should errors
and retries be counted?).
