by ensuring that newly allocated blocks are zerod. The
race can occur even in the case where the write covers
the entire block.
Reported by: Sven Berkvens <sven@berkvens.net>, Marc Olzheim <zlo@zlo.nu>
and had no data available returned 0. Now it returns -1 with errno
set to EWOULDBLOCK (== EAGAIN) as it should. This fix makes the bpf
device usable in threaded programs.
Reviewed by: bde
messages send by routers when they deny our traffic, this causes
a timeout when trying to connect to TCP ports/services on a remote
host, which is blocked by routers or firewalls.
rfc1122 (Requirements for Internet Hosts) section 3.2.2.1 actually
requi re that we treat such a message for a TCP session, that we
treat it like if we had recieved a RST.
quote begin.
A Destination Unreachable message that is received MUST be
reported to the transport layer. The transport layer SHOULD
use the information appropriately; for example, see Sections
4.1.3.3, 4.2.3.9, and 4.2.4 below. A transport protocol
that has its own mechanism for notifying the sender that a
port is unreachable (e.g., TCP, which sends RST segments)
MUST nevertheless accept an ICMP Port Unreachable for the
same purpose.
quote end.
I've written a small extension that implement this, it also create
a sysctl "net.inet.tcp.icmp_admin_prohib_like_rst" to control if
this new behaviour is activated.
When it's activated (set to 1) we'll treat a ICMP administratively
prohibited message (icmp type 3 code 9, 10 and 13) for a TCP
sessions, as if we recived a TCP RST, but only if the TCP session
is in SYN_SENT state.
The reason for only reacting when in SYN_SENT state, is that this
will solve the problem, and at the same time minimize the risk of
this being abused.
I suggest that we enable this new behaviour by default, but it
would be a change of current behaviour, so if people prefer to
leave it disabled by default, at least for now, this would be ok
for me, the attached diff actually have the sysctl set to 0 by
default.
PR: 23086
Submitted by: Jesper Skriver <jesper@skriver.dk>
1. ICMP ECHO and TSTAMP replies are now rate limited.
2. RSTs generated due to packets sent to open and unopen ports
are now limited by seperate counters.
3. Each rate limiting queue now has its own description, as
follows:
Limiting icmp unreach response from 439 to 200 packets per second
Limiting closed port RST response from 283 to 200 packets per second
Limiting open port RST response from 18724 to 200 packets per second
Limiting icmp ping response from 211 to 200 packets per second
Limiting icmp tstamp response from 394 to 200 packets per second
Submitted by: Mike Silbersack <silby@silby.com>
the kernel console. Instead, change logwakeup() to set a flag in the
softc. A callout then wakes up every so often and wakes up any processes
selecting on /dev/log (such as syslogd) if the flag is set. By default
this callout fires 5 times a second, but that can be adjusted by the
sysctl kern.log_wakeups_per_second.
Reviewed by: phk
Add detach routine and turn driver into a module so it can be loaded
and unloaded. Also take a stab at implementing multicast packet
reception so that this NIC will work with IPv6. Promiscuous mode
doesn't seem to work, but I'm not sure why. It works well enough that
I can run dhclient on it and put it on the office network though.
Also ripped out spl stuff and replaced it with mutexes.
This is a driver for the LanMedia/SBE LMC150x E1/T1 family of cards.
The driver currently support unframed E1 (2048kbit/s) and framed
E1 (nx64).
These cards will provision E1/T1 lines for about 1/4 the cost of
a cisco router...
commands have also been slightly updated as follows:
- Use ktr_idx to find the newest entry rather than walking the buffer
comparing timespecs. Timespecs are not always unique after the change
to use getnanotime(9).
- Add a new verbose setting. When the verbose setting is on, then the
timestamp is printed with each message. If KTR_EXTEND is on, then the
filename and line number are output as well. By default this option is
off. It can be turned on with the 'v' modifier passed to the 'tbuf'
and 'tall' commands. For the 'tnext' command, the 'v' modifier toggles
the verbose mode.
- Only display the cpu number for each message on SMP systems.
- Don't display anything for an empty entry that hasn't been used yet.
MS will be treated as having this quirk. In the event that we falsely
identify one that doesn't need it, no harm will be done. Ken
suggested that we make this more generic since there may be more
needed in the future.
Reported by: TERAMOTO Masahiro <teramoto@comm.eng.osaka-u.ac.jp>
PR: kern/23378
Reviewed by: ken
aicasm is run on the build machine and therefore needs to be
compiled and linked against the headers and libraries (resp)
of the build machine. Since normally the default include
directories are search after any specified on the command
line, make sure we don't accidentally pick up machine
dependent headers from the kernel compile directory by
specifying /usr/include first.
This solves the (cross) build problem for ia64.
Approved by: gibbs
functions. If this flag is set, then no KTR log messages are issued.
This is useful for blocking excessive logging, such as with the internal
mutex used by the witness code.
- Use MTX_QUIET on all of the mtx_enter/exit operations on the internal
mutex used by the witness code.
- If we are in a panic, don't do witness checks in witness_enter(),
witness_exit(), and witness_try_enter(), just return.
