With this commit any of the GPIO pins can now be programmed to act as an
interrupt source for GPIO devices (i.e. limited to devices directly
attached to gpiobus - at least for now).
Differential Revision: https://reviews.freebsd.org/D1000
Allocate all four, we will use them soon.
Simplificate the allocation of memory and interrupt resources with a single
bus_alloc_resources() call instead of doing them separately.
Destroy the mutex in case of errors.
With this change, it is now possible to verify the pin function and level
of reserved pins (but not set them).
The use of reserved pins on Raspberry pi can lead to short circuits and
real damage to the SoC.
While here, remove duplicated code, make use of OF_getencprop_alloc()
instead of using fixed sized variables and reduce the dmesg spam by
printing reserved pin ranges (when possible) instead of printing each pin
in the range.
This doesn't actually change any behavior, because it just allows a 16-bit
read of the command register to return the correct value, and nothing
actually does a 16-bit read of that register.
sdhci controllers, such as the one on a Raspberry Pi, mishandle the signal
timing in high speed signaling mode, but run just fine in standard mode
with the bus running at frequencies between 25-50MHz (which shouldn't work).
This is the solution adopted by U-Boot and other OSes (linux and *BSD)
for the timeouts on Raspberry Pi boards with certain SD cards. Some
research shows that this quirk is also used on a few other boards, so the
fix is a generic quirk instead of being in the RPi-specific driver code.
This change is based on information discovered by Michal Meloun.
The driver inherently does dma in 512 byte chunks, but it's possible that
such a buffer can span two physically discontiguous pages (such as when
a userland program does IO on the raw /dev/mmcsdN devices). Now the driver
can handle a buffer that's split across two pages.
It could in theory handle any number of segments now, but as long as IO is
being done in 512 byte blocks it will never need more than two.
requires that each 512 byte IO be in a single contiguous buffer, but if a
buffer crosses a page boundary and the physical pages aren't contiguous
you can get an EFBIG failure (too many segments).
The driver really should handle multiple segment IO, but before adding that
I wanted to make sure that it's handling failure properly while the failure
is easily recreatable.
raft of new warnings that appear to be on by default in clang 3.5.0.
Fix RPI-B build issues with new clang not liking the ability to pass
arbitrary flags to as, since some flags are more arbitrary (and thus
verboten) than others.
These warnings should be actually fixed in the code, but this is a
band-aide to get things (almost) building again.
macro wasn't needed and was being used with swapped arguments which always
give the same result (0) defeating the overflow check.
On initialization, do not use bcm_mbox_intr() to read the pending messages,
with the new semaphore based implementation this will lead to semaphore
being incremented on the channels that contain pending data and will make
the first read for that channel return stale data.
This fixes the hang that happens on boot while initializing the cpufreq on
Raspberry Pi.
can't do a timeout bigger than 15 seconds. The code wasn't checking for
this and because bitmasking was involved the requested timeout was
basically adjusted modulo-16. That led to things like a 128 second
timeout actually being a 9 second timeout, which accidentally worked fine
until watchdogd was changed to only pet the dog once every 10 seconds.
that expose new bugs with HS mode.
When the old code could not do the proper card detection it would boot with
lower defaults (and no HS mode) and this makes some HS cards boots.
Now, with the card always identified as HS capable, the sdhci controller
tries to run the card at HS speeds and makes the boot always fail.
Disable the HS mode for now (which still can be enabled with the tunable)
until it is properly fixed.
MFC with: r273264
Requested by: many
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
used for kernel devices it is used by i2c(8).
This fix the 'error: Device not configured' when i2c(8) tries to reset the
controller, as an example:
# i2c -r
Resetting I2C controller on /dev/iic0: error: Device not configured
For now use conservative settings for default i2c speeds.
MFC after: 1 week
EWOULDBLOCK.
Do not print any message at errors. The errors are properly sent to upper
layers which should be able to deal with it, including printing the errors
when they need to.
The error message was quite annoying while scanning the i2c bus.
MFC after: 1 week
This fix a race where the threads waiting for the bus would wake up early
and still see bus as busy.
While here, give a better description to wmesg for the two use cases we
have (bus and io waiting).
MFC after: 1 week
lose the contents of consecutive writes (that happens within two SD card
clock cycles).
This fixes the causes of instability during the SD card detection and
identification on Raspberry Pi (which happens at 400 kHz and so was much
more vulnerable to this issue).
Remove the previous workaround which clearly can't provide the same effect.
MFC after: 1 week
Relnotes: yes
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
and the functionality it provided into arm/exception.S. Rename the main
irq handling routine from arm_handler_execute() to arm_irq_handler() to
make it more congruent with how other exception handlers are named, and
also update its signature to reflect what has long been reality: it is
passed just a trapframe pointer, no interrupt number argument.
appropriate for each of the 'foo' in the tree. This will allow us to
compile them together (although symbol conflicts prevent us from doing
that today, this just fixes the file name collision).
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
