started to execute, it seems that the corresponding ISR bit in the "old"
local APIC can be cleared. This causes the local APIC interrupt routine
to fail to find an interrupt to service. Rather than panic'ing in this
case, simply return from the interrupt without sending an EOI to the
local APIC. If there are any other pending interrupts in other ISR
registers, the local APIC will assert a new interrupt.
Tested by: steve
In n32 and n64, add support for physical address above 4GB by having
64 bit page table entries and physical addresses. Major changes are:
- param.h: update PTE sizes, masks and shift values to support 64 bit PTEs.
- param.h: remove DELAY(), mips_btop(same as atop), mips_ptob (same as
ptoa), and reformat.
- param.h: remove casting to unsigned long in trunc_page and round_page
since this will be used on physical addresses.
- _types.h: have 64 bit __vm_paddr_t for n32.
- pte.h: update TLB LO0/1 access macros to support 64 bit PTE
- pte.h: assembly macros for PTE operations.
- proc.h: md_upte is now 64 bit for n32 and n64.
- exception.S and swtch.S: use the new PTE macros for PTE operations.
- cpufunc.h: TLB_LO0/1 registers are 64bit for n32 and n64.
- xlr_machdep.c: Add memory segments above 4GB to phys_avail[] as they are
supported now.
Reviewed by: jmallett (earlier version)
the lock instead of queueing it to a task.
- Do not invoke jme_rxintr() to reclaim any unprocessed but received
packets when shutting down the interface. Instead, just drop these
packets to match the behavior of other drivers.
- Hold the driver lock in the interrupt handler to avoid races with
ioctl requests to down the interface.
Reviewed by: yongari
interactive timeshare threads (PRI_*_INTERACTIVE) and non-interactive
timeshare threads (PRI_*_BATCH) and use these instead of PRI_*_REALTIME
and PRI_*_TIMESHARE. No functional change.
Reviewed by: jeff
1. Use vm_paddr_t for physical addresses.
There are a few places in the MIPS platform code where vm_offset_t is
used for physical addresses, change these to use vm_paddr_t:
- phys_avail[], physmem_desc[] arrays
- pmap_mapdev(), page_is_managed(), is_cacheable_mem() pmap_map() args
- local variables of various pmap functions
2. Change init_pte_prot() return from int to pt_entry_t, as this can be
64 bit when using 64 bit TLB entries.
3. Update printing of pt_entry_t and of vm_paddr_t to use 'j' format with
uintmax_t. This will be useful later if we plan to use 64bit phsical addr
on 32 bit n32 compilation.
Reviewed by: imp
bus_size_t may be 32 or 64 bits. Change the bounce_zone alignment field
to explicitly be 32 bits, as I can't really imagine a DMA device that
needs anything close to 2GB alignment of data.
packets.
*) Reject requests with a protocol length not equal to 4. This is IPv4
and there is no reason to accept anything else.
*) Reject packets that have a multicast source hardware address.
*) Drop requests where the hardware address length is not equal
to the hardware address length of the interface.
Pointed out by: Rozhuk Ivan
MFC after: 1 week
The code is turned off until the tree is fixed up so it compiles.
__FreeBSD_version was already bumped once today, so skip the bump, but
add an entry to UPDATING.
Note that __DESCR() is used in the SYSCTL_OID() macro and so is not
needed in macros that invoke it. This use was inconsistent in the
file and I have made it consistent any lines already being changed.
Reviewed by: bde (previous version), -arch (previous version)
dialog is distributed from GPLv2 to LGPLv2 and introduces a number of new
features and a new and better libdialog API. The existing libdialog will
be kept temporarily as libodialog for compatibility purposes until sade,
sysinstall and tzsetup have been either updated or replaced.
__FreeBSD_version is now 900030.
Discussed on: -current
Approved by: core
Obtained from: http://invisible-island.net/dialog
signal action is restored to default in child after fork(2).
In this case there is no need to do anything with dummy SIGCHLD handler,
because after fork(2) it will be automatically reverted to SIG_IGN.
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 3 days
It is possible that the parent process ignores some of them and sigtimedwait()
will never see them, eventhough they are masked.
The most common situation for this to happen is boot process where init(8)
ignores SIGHUP before starting to execute /etc/rc. This in turn caused
hastd(8) to ignore SIGHUP.
Reported by: trasz
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 3 days
