most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.
Special thanks to Glen Neff for helping me test this fix.
night of testing before merging to -stable.
Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
before selecting a mode. The Seeq PHY chips on the Adaptec cards that
use the AIC-6915 controller seem to need it in order to get them to
change modes correctly.
This corrects a problem that I noticed where my ANA-62022 board failed
to correctly program the full duplex bit in the macconfig1 register
when the interface was brought up. Running ifconfig sf0 would mask this
problem in some cases because polling the PHY status would cause the
miibus code to notice that full duplex was now needed and the statchg
callback would be invoked to configure the duplex setting. However it
would still get it wrong other times.
Also changed sf_miibus_statchg() to program the IPG register to match
the duplex setting in accordance with Adaptec manual's recommendations
(0x15 for full duplex, 0x11 for half duplex).
is documented to be 0x18 in the Adaptec manual, however there appears to
be a newer board rev with code 0x19. I added a #define for this and
updated the probe code so that this board will be properly identified
in the probe messages. (Currently it's just identified generically as
an AIC-6915 chip.)
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
