Previously "panic: msleep" could happen for a few different reasons.
Break the KASSERTs out into individual cases to identify the failing
condition. Found during the investigation that resulted in r308288.
Reviewed by: kib, jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8604
sources to return timestamps when SO_TIMESTAMP is enabled. Two additional
clock sources are:
o nanosecond resolution realtime clock (equivalent of CLOCK_REALTIME);
o nanosecond resolution monotonic clock (equivalent of CLOCK_MONOTONIC).
In addition to this, this option provides unified interface to get bintime
(equivalent of using SO_BINTIME), except it also supported with IPv6 where
SO_BINTIME has never been supported. The long term plan is to depreciate
SO_BINTIME and move everything to using SO_TS_CLOCK.
Idea for this enhancement has been briefly discussed on the Net session
during dev summit in Ottawa last June and the general input was positive.
This change is believed to benefit network benchmarks/profiling as well
as other scenarios where precise time of arrival measurement is necessary.
There are two regression test cases as part of this commit: one extends unix
domain test code (unix_cmsg) to test new SCM_XXX types and another one
implementis totally new test case which exchanges UDP packets between two
processes using both conventional methods (i.e. calling clock_gettime(2)
before recv(2) and after send(2)), as well as using setsockopt()+recv() in
receive path. The resulting delays are checked for sanity for all supported
clock types.
Reviewed by: adrian, gnn
Differential Revision: https://reviews.freebsd.org/D9171
gtaskqueue bits at SI_SUB_INIT_IF instead of waiting until SI_SUB_SMP
which is far too late.
Add an assertion in taskqgroup_attach() to catch startup initialization
failures in the future.
Reported by: kib bde
it into pmap-v4.h where they are used. Other than those few lines of
support for different MMU types, nothing in cpuconf.h has been used in our
code for quite a while.
The file existed to set up a variety of symbols to describe the
architecture. Over the past few years we have converted all of our source
to use the new architecture symbols standardized by ARM Inc, and predefined
by both clang and gcc.
PR: 216104
It seems like kern_data_resid was never really implemented. This change
finally does it. Now frontends update this field while transferring data,
while CTL/backends getting it can more flexibly handle the result.
At this point behavior should not change significantly, still reporting
errors on write overrun, but that may be changed later, if we decide so.
CAM target frontend still does not properly handle overruns due to CAM API
limitations. We may need to add some fields to struct ccb_accept_tio to
pass information about initiator requested transfer size(s).
MFC after: 2 weeks
This patch adds driver for temperature/humidity sensor connected via GPIO.
To compile it into kernel add "device gpioths". To activate driver, use
hints (.at and .pins) for gpiobus. As result it will provide temperature &
humidity values via sysctl.
DHT11 is cheap & popular temperature/humidity sensor used via GPIO on ARM
or MIPS devices like Raspberry Pi or Onion Omega.
Reviewed by: adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D9185
The find_currdev() is using variable "copy" to store the reference to trimmed
devpath pointer, if for some reason the efi_devpath_handle() fails, we will
leak this copy.
Also we can simplify the code there a bit.
Reviewed by: allanjude
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D9191
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
arswitch_setled() and a number of _global_setup functions did not acquire the
lock before calling arswitch_modifyreg(). With WITNESS enabled this would
instantly panic.
Discovered on a TPLink-3600:
("panic: mutex arswitch not owned at sys/dev/etherswitch/arswitch/arswitch_reg.c:236")
Reviewed by: adrian, kan
Differential Revision: https://reviews.freebsd.org/D9187
between exp(3) and `exp` var.
The approach taken previously was not ideal for multiple
functional and stylistic reasons.
Add to existing sed call in Makefile to replace `exp` with
`exponent` instead.
MFC after: 13 days
Requested by: bde
vm_object_madvise() is frequently used to apply advice to a contiguous
set of pages in an object with no backing object. Optimize this case by
skipping non-resident subranges in constant time, and by iterating over
resident pages using the object memq, thus avoiding radix tree lookups on
each page index in the specified range.
While here, move MADV_WILLNEED handling to vm_page_advise(), and rename the
"advise" parameter to vm_object_madvise() to "advice."
Reviewed by: alc, kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D9098
sys/net/iflib.c:
Add ctx to filter_info and don't skpi interrupt early on unless we're on an
SMP system
sys/kern/subr_gtaskqueue.c:
Skip smp check if we're running UP
Submitted by: Matt Macy <mmacy@nextbsd.org>
Reported by: emaste bde
This is Micrel KSZ8995MA driver code. KSZ8995MA uses SPI bus to control.
This code is written & tested on @SRCHACK's ksz8995ma board and FON2100
with gpiospi.
etherswitchcfg support commands: addtag, ingress, striptag, dropuntagged.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka, adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8790
This patch adds missing hints for ath0 (eepromaddr) and GPIO (mask & leds).
ath0 doesn't work without eeprom hints, so this commit should make wifi
works on Onion Omega.
GPIO mask is required if you want to use gpiobus and GPIO pins on your
board. Onion Omega has several leds connected to gpio pins (one on board,
one color on dock).
This commit adds mask for gpiobus and allow you to turn off/on leds via
/dev/leds/{board,blue,green,red} (on by default).
Tested on Onion Omega 1.
Reviewed by: adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D9107
This is needed for kernel dumps to work, as the panicking thread will call
into code that makes use of kernel locks.
Reported and tested by: Eugene Grosbein
MFC after: 1 week
the cmap lock. Releasing the lock first may result in the thread
being immediately rescheduled and bound to the same CPU, only to
unpin itself upon resuming execution.
Noted by: skra (in review for armv6 equivalent)
MFC after: 1 week
This helps fix a -Wshadow issue with exp(3) with tests/sys/acct/acct_test,
which include math.h, which in turn defines exp(3)
MFC after: 2 weeks
Tested with: clang, gcc 4.2.1, gcc 4.9
Sponsored by: Dell EMC Isilon
dropped then reacquired due to using M_WAITOK, which opens a window in
which the tty device can disappear. Check for this and return ENXIO
back up the call chain so that callers can cope.
This closes a race where TF_GONE would get set while buffers were being
allocated as part of ttydev_open(), causing a subsequent call to
ttydevsw_modem() later in ttydev_open() to assert.
Reported by: pho
Reviewed by: kib
header match when using a raw socket to send IPv4 packets and
providing the header. If they don't match, let send return -1
and set errno to EINVAL.
Before this patch is was only enforced that the length in the header
is not larger then the buffer length.
PR: 212283
Reviewed by: ae, gnn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9161
I added IEEE80211_TX_LOCK() a few years ago because there were races between
seqno allocation, driver queuing and crypto IV allocation. This meant that
they'd appear out of sequence and the receiver would drop them, leading to
terrible performance or flat out traffic hangs.
This flag should be set by drivers that do their own sequence number
allocation for all frames it needs to happen for, including beacon frames.
Eventually this should lead to the driver taking care of locking for
allocating seqno and other traffic-triggered events (eg addba setup.)
This is the bulk of the magic to start enabling VHT channel negotiation.
It is absolutely, positively not yet even a complete VHT wave-1 implementation.
* parse IEs in scan, assoc req/resp, probe req/resp;
* break apart the channel upgrade from the HT IE parsing - do it after the
VHT IEs are parsed;
* (dirty! sigh) add channel width decision making in ieee80211_ht.c htinfo_update_chw().
This is the main bit where negotiated channel promotion through IEs occur.
* Shoehorn in VHT node init ,teardown, rate control, etc calls like the HT
versions;
* Do VHT channel adjustment where appropriate
Tested:
* monitor mode, ath10k port
* STA mode, ath10k port - VHT20, VHT40, VHT80 modes
TODO:
* IBSS;
* hostap;
* (ignore mesh, wds for now);
* finish 11n state engine - channel width change, opmode notifications, SMPS, etc;
* VHT basic rate negotiation and acceptance criteria when scanning, associating, etc;
* VHT control/management frame handling (group managment and operating mode being
the two big ones);
* Verify TX/RX VHT rate negotiation is actually working correctly.
Whilst here, add some comments about seqno allocation and locking. To achieve
the full VHT rates I need to push seqno allocation into the drivers and
finally remove the IEEE80211_TX_LOCK() I added years ago to fix issues. :/
This sets up:
* vht capabilities in vaps;
* calls vht_announce to announce VHT capabilities if any;
* sets up vht20, vht40 and vht80 channels, assuming the regulatory code
does the right thing with 80MHz available ranges;
* adds support to the ieee80211_add_channel_list_5ghz() code to populate
VHT channels, as this is the API my ath10k driver is using;
* add support for the freq1/freq2 field population and lookup that
VHT channels require.
The VHT80 code assumes that the regulatory domain already has limited VHT80
bands to, well, 80MHz wide chunks.
These are of the few cases where we use the GCC non-null attributes in
non-header code. As part of a review [1] of our use of such attributes we
are replacing such uses of the overly aggressive GCC attribute with clang's
_Nonnull attribute.
In this case the attributes serve little purpose as they just don't
enforce run time checks, If anything the attributes would cause NULL pointer
checks to be ignored but there are no such checks so only effect is
cosmetic.
The references appear to be left over from code development and likely
already fulfilled their purpose.
Reference [1]:
https://reviews.freebsd.org/D9004
Reviewed by: jhb
MFC after: 3 weeks
