inevitable component in Sun Exx00 machines and provides serial ports,
NVRAM and TOD amongst others which are handled by uart(4) and eeprom(4)
respectively). This driver currently only prints out information about
the chassis on attach and allows to blink the 'Cycling' LED (which is
duplicated on the front panel) of the clock board just like fhc(4) does
for the other boards. The device name for the LED is /dev/led/clockboard.
Obtained from: OpenBSD
Tested by: joerg
bus_generic_rl_release_resource() for the bus_release_resource() method
instead of a local copy.
- Correctly handle pass-through allocations in fhc_alloc_resource().
- In case the board model can't be determined just print "unknown model"
so the physical slot number is reported in any case.
- Add support for blinking the 'Cycling' LED of boards on a fhc(4) hanging
of off the nexus (i.e. all boards except the clock board) via led(4).
All boards have at least 3 controllable status LEDs, 'Power', 'Failure'
and 'Cycling'. While the 'Cycling' LED is suitable for signaling from
the OS the others are better off being controlled by the firmware.
The device name for the 'Cycling' LED of each board is /dev/led/boardX
where X is the physical slot number of the board. [1]
Obtained from: OpenBSD [1]
Tested by: joerg [1]
bus_generic_rl_release_resource() for the bus_release_resource() method
instead of a local copy.
- Correctly handle pass-through allocations in central_alloc_resource().
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
last in the list rather than first.
This makes the resouces print in the 4.x order rather than the 5.x order
(eg fdc0 at 0x3f0-0x3f5,0x3f7 is 4.x, but 0x3f7,0x3f0-0x3f5 is 5.x). This
also means that the pci code will once again print the resources in BAR
ascending order.
w/o problems than I was before... This simply brings back the knote_delete
as knlist_delete which will also drop the knote's, instead of just clearing
the list and seeing _ONESHOT...
Fix a race where if a note was _INFLUX and _DETACHED, it could end up being
modified... whoopse..
MFC after: 1 week
Prodded by: ambrisko and dwhite
same value as the previous ioctls so no binary change. Also, make a few
style changes to reduce diffs to my tree.
Loosely based on code from: Hans Petter Selasky
system have been attached, but no later. This ensures that we do
not explore ohci or uhci busses before the companion echi controller
has been initialised, so it should fix the problem of multi-speed
USB devices getting attached as USB 1 devices first and then
re-attached as USB 2.
Some further changes are needed on architectures that do not currently
allow hooks to be inserted before configure_final() - alpha, ia64,
powerpc and sparc64. On these architectures the exploration will
now be delayed until the usb kthread runs.
alignment restrictive, and help performance on some ethernet cards which
currently copy the entire packet a couple bytes to get the packet aligned
properly...
Wordsmithing by: dwhite
Obtained from: NetBSD (code only)
I'll clean it up later: rwatson
in the window between the beginning of panic() and entering the debugger,
it's possible to receive interrupts. If we receive an interrupt, don't
preempt if panicstr != NULL, as the system is in the process of failing, and
the preempting thread is likely to stumble over the failure. The typical
scenario is during the printf() in panic() prior to entering the debugger,
but when running with a slower console type such as serial console.
It could be that the panic string should be passed to the debugger to print,
so that it can run from the debugger's environment rather than a regular
kernel printf.
Glanced at by: jhb
Do our best to plug some memory leaks (VPD data, jumbo memory buffer,...).
Log if we cannot free because memory still in use[1].
Change locking to avoid ''acquiring duplicate lock of same
type: "network driver"'' and potential deadlock. Also seems to fix LOR #063.
[1] This change does not solve problems if buffers are still in use when
unloading if_sk.ko. There is ongoing work which will address jumbogram
allocations in a more general way.
PR: kern/75677 (with changes, no mii fixes in here)
Tested by: net, Antoine Brodin (slightly different version)
Approved by: rwatson (mentor)
MFC after: 5 days
Obtained from: NetBSD if_sk.c rev. 1.11
* Take PHY out of reset for Yukon Lite Rev. A3.
Submitted by: postings on net@ in thread "skc0: no PHY found", 2005-02-22
Tested by: net
Approved by: rwatson (mentor)
MFC after: 5 days
if the interface is marked RUNNING.
Obtained from: NetBSD if_sk.c rev. 1.12
* Don't initialize the card (and start an autonegotiation) every time the IP
address changes. Makes 'dhclient sk0' invocations way faster and more
consistant. i.e. one DHCPREQUEST elicits the DHCPACK.
Obtained from: OpenBSD if_sk.c rev. 1.56
* Additional locking changes in sk_ioctl.
PR: kern/61296 should see improvements by the last two.
Approved by: rwatson (mentor)
MFC after: 5 days
doing that in bfe_stop().
This should fix a panic recently reported on -current occuring when taking
device down then up. In the original implementation, an "ifconfig bfe0 down"
triggers bfe_stop(), which also destroys all TX/RX descriptor dmamaps. Hence
the subsequent "ifconfig bfe0 up" would force the device to use those
already-released dmamap and thus panic the kernel.
PR: kern/77804
Submitted by: Frank Mayhar <frank at exit dot com>
Reviewed by: dmlb, sam (mentor)
Tested by: Phil <pcasidy at casidy dot com>, myself
MFC after: 1 week
session in tprintf(). SESSRELE() needs to properly dispose of the
sessions mutex.
Add sessrele() which does the proper cleanup and have SESSRELE() call it.
Use SESSRELE also in pgdelete().
Found by: Coverity (ID:526)
a given page and, if the pmap is the current pmap, write back the associated
cache line.
Use pmap_wb_page in pmap_qenter() instead of inconditionally
write back/invalidating the data cache.
o Use IP_NPX in preference to hard coded value to write 0 to clear busy#
o Use md macro for a full reset of the npx
o Use IRQ_NPX in preference to hard coded value for each platform.
# The other two ifdefs in this file are hard to remove
rman_resource_resournce_bound wrt end parameter. The end parameter
here was the same as the start. However, it should be start + count -
1, so make it that instead.
it to get better hashing in vfs_hash.
In case of an insert collision in vfs_hash_insert(), put the loosing vnode
on a special list so that vfs_hash_remove() can just assume that it is on
a list.
Drop the VI_HASHED flag.
where having this disabled was actually hurting us, since so many
BIOSes include legacy USB emulation that takes control of all usb
ports and only the ehci driver knows how to disable it.
