route interrupts if the child bus is described in the PCIBIOS interrupt
routing table. For child busses that are in the routing table, they do
not necessarily use a 'swizzle' on their pins on the parent bus to route
interrupts for child devices. If the child bus is an embedded device then
the pins on the child devices can be (and usually are) directly connected
either to a PIC or to a Interrupt Router. This fixes PCIBIOS interrupt
routing across PCI-PCI bridges for embedded devices.
IRQ for an entry in a PCIBIOS interrupt routing ($PIR) table.
- Change pci_cfgintr() to except the current IRQ of a device as a fourth
argument and to use that IRQ for the device if it is valid.
- If an intpin entry in a $PIR entry has a link of 0, it means that that
intpin isn't connected to anything that can trigger an interrupt. Thus,
test the link against 0 to find invalid entries in the table instead of
implicitly relying on the irqs field to be zero. In the machines I have
looked at, intpin entries with a link of 0 often have the bits for all
possible interrupts for PCI devices set.
not the 'entry' member. The entry point is formed from both a base and
a relative entry point. 'entry' is that relative offset. It is perfectly
valid to have an entry point with a relative offset of 0. PCIbios.ventry
is the virtual address of the entry point that takes both 'base' and
'entry' into account, thus it is the proper variable to test to see if we
have an entry point or not.
identify this gadget on the CPUID result alone, so I intend to activate
the necessary magic (i8254 frequency for instance) for it based on the
precense of the on-chip host to PCI bridge.
Don't require pin be non-zero before we map bogus intlines, always do it.
This fixes a number of problems on HP Omnibook computers.
Tested/Reviewed by: Brooks Davis
2, but that's not the case. This fixes the case where there were slots
in the PIR table that had no bits set, but we assumed they did and used
strange results as a result.
o Map invalid INTLINE registers to 255 in pci_cfgreg.c. This should allow
us to remove the bogus checks in MI code for non-255 values.
I put these changes out for review a while ago, but no one responded
to them, so into current they go.
This should help us work better on machines that don't route
interrupts in the traditional way.
MFC After: 4286 millifortnights
older PCI BIOSes hate this and this leads to panics when it is done. Also,
assume that a uniquely routed interrupt is already routed. This also
seems to help some older laptops with feable BIOSes cope.
This typo keeps us from properly routing an interrupt for CardBus
bridges on this machine. So, now we look for $PIR and then _PIR to
cope. With these changes, the Libretto L1 now works properly.
Evidentally, the idea comes from patch that the Japanese version of
RedHat (or against a Japanese version of Red Hat), but my Japanese
isn't good enough to to know for sure.
Reported by: Hiroyuki Aizu-san <eyes@navi.org>
# This may be an MFC candidate, but I'm not yet sure.
Merge in the irq 0 detection. Add comment about why.
If we have irq 0, ignore it like we do irq 255. Some BIOS writers aren't
careful like they should be.
multiple times, others do. The last strategy, which was to assume
that already routed interrupts were good and just return them doesn't
work for some laptops. So, instead, we have a new strategy: we notice
that we have an interrupt that's already routed. We go ahead and try
to route it, none the less. We will assume that it is correctly
routed, even if the route fails. We still assume that other failures
in the bios32 call are because the interrupt is NOT routed.
Note: some laptops do not support the bios32 interface to PCI BIOS and
we need to call it via the INT 2A interface. That is another windmill
to till at later.
Also correct a minor typo and minor whitespace nits.
Strong MFC candidate.
and such was just a bad idea and one that users should be forced to
enable if they want it. This patch introduces a hw.pci.enable_pcibios
tunable for those people. This does not impact the pcibios interrupt
routing at all.
Approved by: peter, msmith
some bios vendors took it apon themselves to "censor" the
host->pci bridges from PCIBIOS callers, even when the caller
explicitly asks for them. This includes certain Compaq machines
(eg: DL360) and some laptops.
If we detect this, shut down pcibios and revert to using IO
port bashing.
Under -current, apcica does a better job anyway.
declarations of a variable of the same name. The one in the outer block
was unused and probably just slipped in at one point or another. This
silences a compiler warning.
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
systems.
From the PR:
When 'probe.slot' is PCI_SLOTMAX (== 31) and 'probe.func' is 7,
call to 'pci_cfgread()' here and machine suddenly hangs up.
I don't know why... (or 450GX chipset's bug?)
PR: i386/20379
Submitted by: Masayuki FUKUI <fukui@sonic.nm.fujitsu.co.jp>
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
Some have dual host->PCI bridges for the same logical pci bus (!), eg:
some of the RCC chipsets. This is a 32/64 bit 33/66MHz and dual pci
voltage motherboard so persumably there are electical or signalling
differences but they are otherwise the same logical bus.
The new PCI probe code however was getting somewhat upset about it and
ended up creating two pci bridges to the same logical bus, which caused
devices on that logical bus to appear and be probed twice.
The ACPI data on this box correctly identifies this stuff, so bring on
ACPI! :-)
pcib_set_bus() cannot be used on the new child because it is
meant to be used on the *pci* device (it looks at the parent internally)
not the pcib being added. Bite the bullet and use ivars for the bus
number to avoid any doubts about whether the softc is consistant between
probe and attach. This should not break the Alpha code.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
