floating before). Attach pccard devices to pcic, one per slot
(although this may change to one per pcic). pcic is now attached to
isa (to act as a bridge) and pccard is attached to pcic, cbb and
pc98ic (the last two are card bus bridge and the pc98ic version of
pcic, neither of which are in the tree yet). Move pccard compat code
into pccard/pccard_compat.c.
THIS REQUIRES A CONFIG FILE CHANGE. You must change your pcic/card
entries to be:
# PCCARD (PCMCIA) support
controller pcic0 at isa?
controller pcic1 at isa?
controller card0
The old system was upside down and this corrects that problem. It
will make it easier to add support for YENTA pccard/card bus bridges.
Much more cleanup needs to happen before newbus devices can have
pccard attachments. My previous commit's comments were premature.
now lives in the respective bus front end files.
- Add various function prototypes to if_edvar.h
- Clean up some debugging code that snuck into if_ed_isa.c
- Turn on the right bits in files.i386
* Change the hack used on the alpha for mapping devices into DENSE or
BWX memory spaces to a simpler one. Its still a hack and should be
a seperate api to explicitly map the resource.
* Add $FreeBSD$ as necessary.
* Move pnp_eisaformat() to pnp.c, declared in <isa/pnpvar.h>.
* Turn the pnpbios code into an enumerator for the isa bus. This allows
all devices known to the bios to be probed automatically.
Currently the pnpbios code is dependant on the PNPBIOS option. As the code
is tested more and when more drivers are converted this will be made the
default. I have PnP changes in the wings for fdc, atkbd, psm, pcaudio, and
joy. Sio already works with pnpbios.
same interface as Intel's P6 family has. Incidentally, I had disabled
it in the first place since I knew the K7s were coming out soon but
did not want to assume they'd have the same MTRR interface as Intel's
chips.
Submitted by: Ville-Pertti Keinonen <will@iki.fi>
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
can provide the correct context to each signal handler.
Fix broken sigsuspend(): don't use p_oldsigmask as a flag, use SAS_OLDMASK
as we did before the linuxthreads support merge (submitted by bde).
Move ps_sigstk from to p_sigacts to the main proc structure since signal
stack should not be shared among threads.
Move SAS_OLDMASK and SAS_ALTSTACK flags from sigacts::ps_flags to proc::p_flag.
Move PS_NOCLDSTOP and PS_NOCLDWAIT flags from proc::p_flag to procsig::ps_flag.
Reviewed by: marcel, jdp, bde
o Remove unused defines from genassym.c that were needed
by the trampoline.
o Add load_gs_param function to support.s that catches
a fault when %gs is loaded with an invalid descriptor.
The function returns EFAULT in that case.
o Remove struct trapframe from mcontext_t and replace it
with the list of registers.
o Modify sendsig and sigreturn accordingly.
This commit contains a patch by bde.
Reviewed by: luoqi, jdp
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
struct sigcontext and ucontext_t/mcontext_t are defined in such
a way that both (ie struct sigcontext and ucontext_t) can be
passed on to sigreturn. The signal handler is still given a
ucontext_t for maximum flexibility.
For backward compatibility sigreturn restores the state for the
alternate signal stack from sigcontext.sc_onstack and not from
ucontext_t.uc_stack. A good way to determine which value the
application has set and thus which value to use, is still open
for discussion.
NOTE: This change should only affect those binaries that use
sigcontext and/or ucontext_t. In the source tree itself
this is only doscmd. Recompilation is required for those
applications.
This commit also fixes a lot of style bugs without hopefully
adding new ones.
NOTE: struct sigaltstack.ss_size now has type size_t again. For
some reason I changed that into unsigned int.
Parts submitted by: bde
sigaltstack bug found by: bde
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
1. Break out the definition of the soft state structure into an include
file.
2. un-static the soft state and apm_display(), and group them under a
comment that notes the dependency.
Turn on the 'new' if_ep driver which supports:
ISA 3c509
MCA 3c529
EISA 3c579
PCCARD 3c589
I think all we're missing is support for the VME bus and S-100 bus
Etherlink III cards.
The new code has been tested by a number of people and all the important
bits work. I've not been able to test the EISA code but will do so once
my hardware arrives. Since I've changed nothing in the EISA code I suspect
it will perform the same manner as before.
Future changes involve whacking the ISA and PCCARD front ends to use
newbus and to convert the driver to bus_space and make it use ifmedia.
This is the first working network driver that supports MCA bus devices btw.
Enjoy.
-----------------------------
The compatibility code and/or emulators have been updated:
iBCS2 now mostly uses the older syscalls. SVR4 now properly
handles all signals. This has been achieved by using the
new sigset_t throughout the emulator. The Linuxulator has
been severely updated. Internally the new Linux sigset_t is
made the default. These are then mapped to and from the
new FreeBSD sigset_t.
Also, rt_sigsuspend has been implemented in the Linuxulator.
Implementing this syscall basicly caused all this sigset_t
changing in the first place and the syscall has been used
throughout the change as a means for testing. It basicly is
too much work to undo the implementation so that it can
later be added again.
A special note on the use of sv_sigtbl and sv_sigsize in
struct sysentvec:
Every signal larger than sv_sigsize is not translated and is
passed on to the signal handler unmodified. Signals in the
range 1 upto and including sv_sigsize are translated.
The rationale is that only the system defined signals need to
be translated.
The emulators also have been updated so that the translation
tables are only indexed for valid (system defined) signals.
This change also fixes the translation bug already in the
SVR4 emulator.
-----------------------------
By introducing a new sigframe so that the signal handler operates
on the new siginfo_t and on ucontext_t instead of sigcontext, we
now need two version of sendsig and sigreturn.
A flag in struct proc determines whether the process expects an
old sigframe or a new sigframe. The signal trampoline handles
which sigreturn to call. It does this by testing for a magic
cookie in the frame.
The alpha uses osigreturn to implement longjmp. This means that
osigreturn is not only used for compatibility with existing
binaries. To handle the new sigset_t, setjmp saves it in
sc_reserved (see NOTE).
the struct sigframe has been moved from frame.h to sigframe.h
to handle the complex header dependencies that was caused by
the new sigframe.
NOTE: For the i386, the size of jmp_buf has been increased to hold
the new sigset_t. On the alpha this has been prevented by
using sc_reserved in sigcontext.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
for you to be told there was an error [during verbose boot].
I poked him for the fix, he poked me to get it committed.
Submitted by: Jason Young <doogie@anet-stl.com>
there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
be set by a kernel conf option due to the struct buf structural
dependancy (sizing of b_pages[]) creating a conflict with modules
(which are not compiled with kernel config options overrides).
We'll be able to sysctl these two later on when the buffer subsystem
is revamped.
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
spaces which cross a segment boundry in the page table. pmap_kextract()
is not designed for access to the user space portion of the page
table and cannot handle the null-page-directory-entry case.
The fix is to have vm_fault_quick() return a success or failure which
is then used to avoid calling pmap_kextract().
It is about 2.5 microseconds or roughly 3 times faster to use this
"PIIX" timecounter than the "i8254" timecounter. Resolution is
also 3 times better.
The code cheats and don't register the PCI device, because other pieces
of code want to use it too.
Originally spotted by: msmith
far-reaching in fd-land, so you'll want to consult the code for
changes. The biggest change is that now, you don't use
fp->f_ops->fo_foo(fp, bar)
but instead
fo_foo(fp, bar),
which increments and decrements the fp refcount upon entry and exit.
Two new calls, fhold() and fdrop(), are provided. Each does what it
seems like it should, and if fdrop() brings the refcount to zero, the
fd is freed as well.
Thanks to peter ("to hell with it, it looks ok to me.") for his review.
Thanks to msmith for keeping me from putting locks everywhere :)
Reviewed by: peter
users have suffered from this breakage, w/o commitment from someone that
they would fix the problems.
This effectively backs out revs 1.{157-160}. It does however fix the
build problem that caused 1.157 to be committed.
If the changes from rev 1.156-1.160 can't be fully tested by the
committer, may I offer posting a diff in the freebsd-current mailing
list for broader testing before inflicting this breakage again.
1) Reworked the probe routine
2) Addition of the 574B's product ID.
3) Added useful info when booting verbosely.
Submitted by: Jason Young <doogie@anet-stl.com>
warnings caused by the arg having the wrong type (not const enough).
The arg was also wrong (a full name instead of a short one) for calls
from from subr_diskmbr.c and pc98/diskslice_machdep.c.
random-seekable devices. This lets dd(1) know it can seek on them. It
also affects spec_vnopen() (IIRC), but only makes the path of execution smaller,
and does not change its behavior. This is when securelevel >= 2.
the OS does FXSAVE/FXRESTOR instructions (fast FPU save/restore) during
context switching and also enables SIMD since this enables saving the
extra CPU context that isn't saved with normal FPU regs. The other
enables the SIMD instructions to use exception 16 (FPU) error reporting.
Note, this doesn't turn on SIMD, just defines the bits.
return (in signal trampoline code). I plan to do the same on -stable,
so that we have a consistent interface to userland applications.
Reviewed by: bde
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
a quick think and discussion among various people some form of some of
these changes will probably be recommitted.
The reversion requested was requested by dg while discussions proceed.
PHK has indicated that he can live with this, and it has been agreed
that some form of some of these changes may return shortly after further
discussion.
the actual work. When USER_LDT is not defined for a kernel, sysarch returns
EOPNOTSUPP. Display a message in that case and return ENOSYS to userland.
Reviewed by: luoqi
1. Move definitions of struct i386_*_args to the header file sysarch.h,
since they are part of the sysarch API. struct i386_get_ldt_args and
i386_set_ldt_args were identical, therefore make them into one
struct i386_ldt_args. Libc should use these definitions as well.
2. Return a more sensible EOPNOTSUPP for unknown operations.
Reviewed by: marcel
`ED_P1_MAR + i' and `ED_P1_PAR + i', respectively.
- convert ED_PC_RESET and ED_PC_MISC into relative offset from
ED_PC_ASIC_OFFSET (those macros are not used in current source).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
the new PnP code. Since the bulk of the driver changes are not being
committed at this time, it will not affect the driver. The code is being
committed early to allow others synchronise changes.
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Remove WD formatting code which has never worked in 386bsd or FreeBSD.
Remove DIOCSSTEP and DIOCSRETRIES ioctls as well, they belong in
history, along with the SMD disks.
OK'ed by: bde
an operation, as a kernel client may not have previously checked the CPU
type (it may not be able to).
Also correct the function declaration style for the mem_range functions to
match the rest of this file (oops).
Submitted by: gibbs
the highly non-recommended option ALLOW_BDEV_ACCESS is used.
(bdev access is evil because you don't get write errors reported.)
Kill si_bsize_best before it kills Matt :-)
Use the specfs routines rather having cloned copies in devfs.
UMAPFS_DIAGNOSTIC and UNION_DIAGNOSTIC. Uncommented NULLFS_DIAGNOSTIC.
It is as bogus as the above three but since it is already a new-style
option it is easier to use it than to fix it.
discussed on current.
The following variables are defined (for now):
osname (defaults to "Linux")
Allow users to change the name of the OS as returned by uname(2),
specially added for all those Linux Netscape users and statistics
maniacs :-) We now have what we all wanted!
osrelease (defaults to "2.2.5")
Allow users to change the version of the OS as returned by uname(2).
Since -current supports glibc2.1 now, change the default to 2.2.5
(was 2.0.36).
oss_version (defaults to 198144 [0x030600])
This one will be used by the OSS_GETVERSION ioctl (PR 12917) which I
can commit now that we have the MIB. The default version number is the
lowest version possible with the current 'encoding'.
A note about imprisoned processes (see jail(2)):
These variables are copy-on-write (as suggested by phk). This means that
imprisoned processes will use the system wide value unless it is written/set
by the process. From that moment on, a copy local to the prison will be
used.
A note about the implementation:
I choose to add a single pointer to struct prison, because I didn't like the
idea of changing struct prison every time I come up with a new variable. As
a side effect, the extra storage is only needed when a variable is set from
within the prison. This also minimizes kernel bloat when the Linuxulator is
not used; both compiled in or as a module.
Reviewed by: bde (first version only) and phk
