value is defined as a config option the definition is emitted into
opt_global.h which is force-included into everything. In addition, the
symbol is emitted by the genassym mechanism, but that by its nature reduces
the value to a 0xnnnnnnnn number. When compiling a .S file you end up
with two different definitions of the macro (they evaluate to the same
number, but the text is different, upsetting the compiler).
Nothing has changed about this code for a while but the compile error is
new, so this must be fallout from the clang 3.7 update or something.
The early ethernet MACs (I think AR71xx and AR913x) require that both
TX and RX require 4-byte alignment for all packets.
The later MACs have started relaxing the requirements.
For now, the 1-byte TX and 1-byte RX alignment requirements are only for
the QCA955x SoCs. I'll add in the relaxed requirements as I review the
datasheets and do testing.
* Add a hardware flags field and 1-byte / 4-byte TX/RX alignment.
* .. defaulting to 4-byte TX and 4-byte RX alignment.
* Only enforce the TX alignment fixup if the hardware requires a 4-byte
TX alignment. This avoids a call to m_defrag().
* Add counters for various situations for further debugging.
* Set the 1-byte and 4-byte busdma alignment requirement when
the tag is created.
This improves the straight bridging performance from 130mbit/sec
to 180mbit/sec, purely by removing the need for TX path bounce buffers.
The main performance issue is the RX alignment requirement and any RX
bounce buffering that's occuring. (In a local test, removing the RX
fixup path and just aligning buffers raises the performance to above
400mbit/sec.
In theory it's a no-op for SoCs before the QCA955x.
Tested:
* QCA9558 SoC in AP135 board, using software bridging between arge0/arge1.
an extra argument to specify the number of 1GiB pages to map. This should
be a nop as we are only mapping a single page, but when we move to use an
extra level of page tables we will be able to map a second block, e.g. if
the kernel was loaded over a 1GiB boundary.
atapicd(4) has been removed since r249083, and if a system has more than one
optical drive, it will likely be /dev/cd1
Update mount.conf(8) to reflect the change in behavior
MFC after: never
Sponsored by: EMC / Isilon Storage Division
an error.
Most of these do a 'mkdir -p' or 'install -d' before installing, but add
the trailing / here for consistency with the userland install.
MFC after: 2 weeks
X-MFC-With: r289391
Sponsored by: EMC / Isilon Storage Division
4185 add new cryptographic checksums to ZFS: SHA-512, Skein, Edon-R
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: Matthew Ahrens <mahrens@delphix.com>
illumos/illumos-gate@45818ee124
This is only a partial merge of respective ZFS infrastructure changes.
At this moment FreeBSD kernel has no those crypto algorithms, so the
parts of the code to enable them are commented out. When they are
implemented, it will be trivial to plug them in.
MACHINE_CPUARCH expands to aarch64 for arm64, whereas MACHINE always
corresponds to the directory name under sys/ that contains the sources
for that architecture.
deletions. Ability to do deletions is a strong indication that this
optimization will not help performance. It will only generate extra write
traffic. These devices are typically flash based and have a limited number of
write cycles. In addition, making the file contiguous in LBA space doesn't
improve the access times from flash devices because they have no seek time.
Reviewed by: mckusick@
bug of installing 'realtek' and 'intel_iwn' as files rather then as
a 'LICENSE' file in their directories.
Also add obsolete entries for the older names and names that existed in head
for a period of time.
Suggested by: jmg
X-MFC-With: r289391
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
On the Haswell platform, a split BAR option to allow creation of 2 32bit
BARs (4 and 5) from the 64bit BAR 4. Adding support for this new option.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
This is a follow-up to r289208: "Xeon Errata Workaround."
Add logic to support a variable number of memory windows and doorbell
callbacks. This was added to the Linux driver in the "Xeon Errata
Workaround" commit, but I skipped it because it didn't look neccessary
at the time. It is needed for future Haswell split-BAR support, so
bring it in now.
A new tunable was added for if_ntb, 'hw.ntb.max_num_clients'. By
default, it is set to zero -- infer the number of clients from the
number of memory windows available from the hardware. Any other
positive value can specify a different number of clients, limited by the
number of doorbell callbacks available (4 under MSI-X, or 15 (Xeon) or
34 (SoC) under legacy INTx).
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
While trying to get multithreading working for CloudABI on aarch64, I
noticed that compare-and-exchange operations in kernelspace would always
fail. It turns out that we don't properly set the return value to 0 when
the compare and exchange succeeds.
Approved by: andrew
Differential Revision: https://reviews.freebsd.org/D3899
casuword(9) and others, use LDRT and STRT instructions to access
memory with the privileges of userspace. If the *RT instruction
faults on the kernel address, then additional checks must be done to
not confuse the VM system with invalid kernel-mode faults.
Put ARM on line with other FreeBSD architectures and disallow usermode
buffers which intersect with the kernel address space in advance,
before any accesses are performed. In other words, vm_fault(9) is no
longer called when e.g. suword(9) stores to invalid (i.e. not
userspace) address.
Also, switch ARM to use fueword(9) and casueword(9).
Note: there is a pending patch in D3617, which adds the special
processing for faults from LDRT and STRT. The addition of the
processing is useful for potential other uses of the instructions and
for completeness, but standard userspace accessors are better served
by not allowing such faults beforehand.
Reviewed by: andrew
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3816
MFC after: 2 weeks
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Reviewed by: Arne Jansen <sensille@gmx.net>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Matthew Ahrens <mahrens@delphix.com>
illumos/illumos-gate@9c3fd1216f
For more info, see:
- slides http://www.slideshare.net/MatthewAhrens/openzfs-send-and-receive
- video https://www.youtube.com/watch?v=iY44jPMvxog
- manpage changes (for zfs resume -s and zfs send -t)
- upcoming talk at the OpenZFS Developer Summit
The TL;DR is:
Use "zfs receive -s" to save the partially received state on failure.
On failure, get the receive token with "zfs get receive_resume_token <fs>"
Resume the send with "zfs send -t <token_value>"
Relnotes: yes
This patch adds support for the BCM57765[2] card reader function included in
Broadcom's BCM57766 ethernet/sd3.0 controller. This controller is commonly
found in laptops and Apple hardware (MBP, iMac, etc).
The BCM57765 chipset is almost fully compatible with the SD3.0 spec, but
does not support deriving a frequency below 781KHz from its default base
clock via the standard SD3.0-configured 10-bit clock divisor.
If such a divisor is set, card identification (which requires a 400KHz
clock frequency) will time out[1].
As a work-around, I've made use of an undocumented device-specific clock
control register to switch the controller to a 63MHz clock source when
targeting clock speeds below 781KHz; the clock source is likewise switched
back to the 200MHz clock when targeting speeds greater than 781KHz.
Additionally, this patch fixes a small sdhci_pci bug; the
sdhci_pci_softc->quirks flag was not copied to the sdhci_slot, resulting in
`quirk` behavior not being applied by sdhci.c.
[1] A number of Linux/FreeBSD users have noted that bringing up the chipsets'
associated ethernet interface will allow SD cards to enumerate (slowly).
This is a controller implementation side-effect triggered by the ethernet
driver's reading of the hardware statistics registers.
[2] This may also fix card detection when using the BCM57785 chipset, but I
don't have access to the BCM57785 chipset and can't verify.
I actually snagged some BCM57785 hardware recently (2012 Retina MacBook Pro)
and can confirm that this also fixes card enumeration with the BCM57785
chipset; with the patch, I can boot off of the internal sdcard reader.
PR: kern/203385
Submitted by: Landon Fuller <landon@landonf.org>
HWPMC depends on pmu.c even if device pmu is not specified.
Would be great if we could just automatically enabled "device pmu"
if we try to compile in HWPMC.
Also several old kernel cnfigurations seem to have HWPMC enabled but are
pre-FDT and thus fail. So make pmu.c depend on fdt in case of hwpmc as
well.
MFC after: 2 weeks
Sponsored by: DARPA/AFRL
Differential Revision: https://reviews.freebsd.org/D3877
Pull out read of PPD and platform detection logic to new functions,
ntb_detect_xeon(), ntb_detect_soc(). No functional change -- mostly
this is just shuffling the code to more closely match the Linux driver.
Linux commit log:
To simplify some of the platform detection code. Move the platform
detection to a function to be called earlier.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The doorbell registers (and associated mask) are 16-bit on Xeon but
64-bit on SoC. Abstract IO access to doorbell registers with
'db_ioread' and 'db_iowrite' (names and idea borrowed from the dual
BSD/GPL Linux driver).
Sponsored by: EMC / Isilon Storage Division
Original Linux commit log:
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Authored by: Dave Jiang
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Remap MSI-X messages over available slots rather than falling back to
legacy INTx when fewer MSI-X slots are available than were requested.
N.B. the Linux driver does *not* do this.
To aid in testing, a tunable 'hw.ntb.force_remap_mode' has been added.
It defaults to off (0). When the tunable is enabled and sufficient
slots were available, the driver restricts the number of slots by one
and remaps the MSI-X messages over the remaining slots.
In case this is actually not okay (as I don't yet have access to this
hardware to test), a tunable 'hw.ntb.prefer_intx_to_remap' has been
added. It defaults to off (0). When the tunable is enabled and fewer
slots are available than requested, fall back to legacy INTx mode rather
than attempting to remap MSI-X messages.
Suggested by: jhb
Reviewed by: jhb (earlier version)
Sponsored by: EMC / Isilon Storage Division
Consumers that registered on this bit would never see a callback and it
is likely a mistake.
This does not affect if_ntb, which limits itself to a single doorbell
callback.
The names don't line up 100% with Linux. Our routines are named
ntb_setup_interrupts, ntb_setup_xeon_msix, ntb_setup_soc_msix, and
ntb_setup_legacy_interrupt. Linux SNB = FreeBSD Xeon; Linux BWD =
FreeBSD SOC. Original Linux commit log:
This is an cleanup effort to make ntb_setup_msix() more readable - use
ntb_setup_bwd_msix() to init MSI-Xs on BWD hardware and
ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the way it should
has been done - looping pci_enable_msix() until success or failure.
Authored by: Alexander Gordeev
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Provide a better event interface between the client and transport.
Authored by: Jon Mason
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
The ERL is a fairly cheap (~$100 USD) and readily available dual core
MIPS64 device so it makes a useful MIPS reference platform.
This is based in part on the kernel config generated by the mkerlimage
script from http://rtfm.net/FreeBSD/ERL/.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3884
To me that seems broken as certain interrupts will never be handled
properly. I'll re-open D3877 and we can seek a better solution and
try again. For now go back to that state and avoid compile time errors.
executable image. Keep one page (arbitrary) limit on the max allowed
size of the PT_NOTES.
The ELF image activators still require that program headers of the
executable are fully contained in the first page of the image file.
Reviewed by: emaste, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D3871
according to the Cortex-A8 TRM r3p2 section 3.2.49.
The A8 list differs from the "ARM-v7 common" list, given the A8
was an earlier model.
There is still more work to be done for other Cortex-Ax version as
andrew points out, but I am just trying to fix A8 for now for teaching.
MFC after: 2 weeks
Sponsored by: DARPA/AFRL
Obtained from: Cambridge/L41
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3876
Would be great if we could just automatically enabled "device pmu"
if we try to compile in HWPMC.
MFC after: 2 weeks
Sponsored by: DARPA/AFRL
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D3877
In certain configurations (mostly but not exclusively as a VM on Xen) pf
produced packets with an invalid TCP checksum.
The problem was that pf could only handle packets with a full checksum. The
FreeBSD IP stack produces TCP packets with a pseudo-header checksum (only
addresses, length and protocol).
Certain network interfaces expect to see the pseudo-header checksum, so they
end up producing packets with invalid checksums.
To fix this stop calculating the full checksum and teach pf to only update TCP
checksums if TSO is disabled or the change affects the pseudo-header checksum.
PR: 154428, 193579, 198868
Reviewed by: sbruno
MFC after: 1 week
Relnotes: yes
Sponsored by: RootBSD
Differential Revision: https://reviews.freebsd.org/D3779
Reviewed by: Richard Yao <ryao@gentoo.org>
Reviewed by: Xin LI <delphij@freebsd.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Author: Justin T. Gibbs <gibbs@FreeBSD.org>
illumos/illumos-gate@d2058105c6