Allow LRO to work on IPv6 as well.
Fix the module Makefile to at least properly inlcude opt_inet6.h
and allow builds without INET or INET6.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
Significantly update tcp_lro for mostly two things:
1) introduce basic support for IPv6 without extension headers.
2) try hard to also get the incremental checksum updates right,
especially also in the IPv4 case for the IP and TCP header.
Move variables around for better locality, factor things out into
functions, allow checksum updates to be compiled out, ...
Leave a few comments on further things to look at in the future,
though that is not the full list.
Update drivers with appropriate #includes as needed for IPv6 data
type in LRO.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
If an IPv6 packet has extension headers the kernel needs to deal with it
itself. For the rest it can set various CSUM_XXX flags and the driver
will act on them.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
Changes since 7.8.0 (from the official changelog):
- Fixed sporadic interrupt generation for associated CQ when processing
a local invalidate work request
- Changes to core scheduling to avoid starving requests from the host
under heavy RDMA Read Request load (e.g. packets to the wire)
- Programmed the tp tx resource limiter in function of the traffic (only
affects iWarp)
- Increased the egress NIC gather list length from 36 to 46 entries
MFC after: 1 week
sbuf_new_for_sysctl(9). This allows using an sbuf with a SYSCTL_OUT
drain for extremely large amounts of data where the caller knows that
appropriate references are held, and sleeping is not an issue.
Inspired by: rwatson
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
condition in proc_rwmem() and to (2) simplify the implementation of the
cxgb driver's vm_fault_hold_user_pages(). Specifically, in proc_rwmem()
the requested read or write could fail because the targeted page could be
reclaimed between the calls to vm_fault() and vm_page_hold().
In collaboration with: kib@
MFC after: 6 weeks
There is no need to use an atomic operation at structure initialization
time.
Note that the file changed is not connected to the build at this time.
Reviewed by: jhb (general issue)
Approved by: np
MFC after: 2 weeks
Add a drain function for struct sysctl_req, and use it for a variety
of handlers, some of which had to do awkward things to get a large
enough SBUF_FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing
NUL byte. This behaviour was preserved, though it should not be
necessary.
Reviewed by: phk (original patch)
unexpected things in copyout(9) and so wiring the user buffer is not
sufficient to perform a copyout(9) while holding a random mutex.
Requested by: nwhitehorn
handlers, some of which had to do awkward things to get a large enough
FIXEDLEN buffer.
Note that some sysctl handlers were explicitly outputting a trailing NUL
byte. This behaviour was preserved, though it should not be necessary.
Reviewed by: phk
10G cards. 1G cards are x4 only.
- Use constants from pcireg.h for reading the current link width.
- Use pci_set_max_read_req() rather than implementing it by hand.
Reviewed by: np
MFC after: 1 week
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.
MFC after: 1 month
The T3 ASIC can provide an incoming packet's timestamp instead of its RSS hash.
The timestamp is just a counter running off the card's clock. With a 175MHz
clock an increment represents ~5.7ns and the 32 bit value wraps around in ~25s.
# sysctl -d dev.cxgbc.0.pkt_timestamp
dev.cxgbc.0.pkt_timestamp: provide packet timestamp instead of connection hash
# sysctl -d dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: core clock frequency (in KHz)
# sysctl dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: 175000
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.
- Use 16k jumbo clusters only on offload capable cards by default.
- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.
- Slightly better freelist size calculation.
- Fix nmbjumbo4 typo, remove unneeded global variables.
MFC after: 3 days
