/*- * Copyright (c) 1990 The Regents of the University of California. * All rights reserved. * * This code is derived from software contributed to Berkeley by * William Jolitz and Don Ahn. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * from: @(#)clock.c 7.2 (Berkeley) 5/12/91 * $Id: clock.c,v 1.43 1995/12/24 08:10:52 davidg Exp $ */ /* * inittodr, settodr and support routines written * by Christoph Robitschko * * reintroduced and updated by Chris Stenton 8/10/94 */ /* * Primitive clock interrupt routines. */ #include "opt_ddb.h" #include #include #include #include #include #include #include #include #include #include #include /* * 32-bit time_t's can't reach leap years before 1904 or after 2036, so we * can use a simple formula for leap years. */ #define LEAPYEAR(y) ((u_int)(y) % 4 == 0) #define DAYSPERYEAR (31+28+31+30+31+30+31+31+30+31+30+31) /* X-tals being what they are, it's nice to be able to fudge this one... */ #ifndef TIMER_FREQ #define TIMER_FREQ 1193182 /* XXX - should be in isa.h */ #endif #define TIMER_DIV(x) ((TIMER_FREQ+(x)/2)/(x)) /* * Time in timer cycles that it takes for microtime() to disable interrupts * and latch the count. microtime() currently uses "cli; outb ..." so it * normally takes less than 2 timer cycles. Add a few for cache misses. * Add a few more to allow for latency in bogus calls to microtime() with * interrupts already disabled. */ #define TIMER0_LATCH_COUNT 20 /* * Minimum maximum count that we are willing to program into timer0. * Must be large enough to guarantee that the timer interrupt handler * returns before the next timer interrupt. Must be larger than * TIMER0_LATCH_COUNT so that we don't have to worry about underflow in * the calculation of timer0_overflow_threshold. */ #define TIMER0_MIN_MAX_COUNT TIMER_DIV(20000) int adjkerntz = 0; /* offset from CMOS clock */ int disable_rtc_set = 0; /* disable resettodr() if != 0 */ u_int idelayed; #if defined(I586_CPU) || defined(I686_CPU) unsigned i586_ctr_rate; long long i586_ctr_bias; long long i586_last_tick; #endif u_int stat_imask = SWI_CLOCK_MASK; int timer0_max_count; u_int timer0_overflow_threshold; u_int timer0_prescaler_count; static int beeping = 0; static u_int clk_imask = HWI_MASK | SWI_MASK; static const u_char daysinmonth[] = {31,28,31,30,31,30,31,31,30,31,30,31}; static u_int hardclock_max_count; /* * XXX new_function and timer_func should not handle clockframes, but * timer_func currently needs to hold hardclock to handle the * timer0_state == 0 case. We should use register_intr()/unregister_intr() * to switch between clkintr() and a slightly different timerintr(). * This will require locking when acquiring and releasing timer0 - the * current (nonexistent) locking doesn't seem to be adequate even now. */ static void (*new_function) __P((struct clockframe *frame)); static u_int new_rate; static u_char rtc_statusa = RTCSA_DIVIDER | RTCSA_NOPROF; static char timer0_state = 0; static char timer2_state = 0; static void (*timer_func) __P((struct clockframe *frame)) = hardclock; #if 0 void clkintr(struct clockframe frame) { hardclock(&frame); setdelayed(); } #else static void clkintr(struct clockframe frame) { timer_func(&frame); switch (timer0_state) { case 0: setdelayed(); break; case 1: if ((timer0_prescaler_count += timer0_max_count) >= hardclock_max_count) { hardclock(&frame); setdelayed(); timer0_prescaler_count -= hardclock_max_count; } break; case 2: setdelayed(); timer0_max_count = TIMER_DIV(new_rate); timer0_overflow_threshold = timer0_max_count - TIMER0_LATCH_COUNT; disable_intr(); outb(TIMER_MODE, TIMER_SEL0 | TIMER_RATEGEN | TIMER_16BIT); outb(TIMER_CNTR0, timer0_max_count & 0xff); outb(TIMER_CNTR0, timer0_max_count >> 8); enable_intr(); timer0_prescaler_count = 0; timer_func = new_function; timer0_state = 1; break; case 3: if ((timer0_prescaler_count += timer0_max_count) >= hardclock_max_count) { hardclock(&frame); setdelayed(); timer0_max_count = hardclock_max_count; timer0_overflow_threshold = timer0_max_count - TIMER0_LATCH_COUNT; disable_intr(); outb(TIMER_MODE, TIMER_SEL0 | TIMER_RATEGEN | TIMER_16BIT); outb(TIMER_CNTR0, timer0_max_count & 0xff); outb(TIMER_CNTR0, timer0_max_count >> 8); enable_intr(); /* * See microtime.s for this magic. */ time.tv_usec += (27645 * (timer0_prescaler_count - hardclock_max_count)) >> 15; if (time.tv_usec >= 1000000) time.tv_usec -= 1000000; timer0_prescaler_count = 0; timer_func = hardclock;; timer0_state = 0; } break; } } #endif int acquire_timer0(int rate, void (*function) __P((struct clockframe *frame))) { if (timer0_state || TIMER_DIV(rate) < TIMER0_MIN_MAX_COUNT || !function) return -1; new_function = function; new_rate = rate; timer0_state = 2; return 0; } int acquire_timer2(int mode) { if (timer2_state) return -1; timer2_state = 1; outb(TIMER_MODE, TIMER_SEL2 | (mode &0x3f)); return 0; } int release_timer0() { if (!timer0_state) return -1; timer0_state = 3; return 0; } int release_timer2() { if (!timer2_state) return -1; timer2_state = 0; outb(TIMER_MODE, TIMER_SEL2|TIMER_SQWAVE|TIMER_16BIT); return 0; } /* * This routine receives statistical clock interrupts from the RTC. * As explained above, these occur at 128 interrupts per second. * When profiling, we receive interrupts at a rate of 1024 Hz. * * This does not actually add as much overhead as it sounds, because * when the statistical clock is active, the hardclock driver no longer * needs to keep (inaccurate) statistics on its own. This decouples * statistics gathering from scheduling interrupts. * * The RTC chip requires that we read status register C (RTC_INTR) * to acknowledge an interrupt, before it will generate the next one. */ static void rtcintr(struct clockframe frame) { u_char stat; stat = rtcin(RTC_INTR); if(stat & RTCIR_PERIOD) { statclock(&frame); } } #ifdef DDB static void DDB_printrtc(void) { printf("%02x/%02x/%02x %02x:%02x:%02x, A = %02x, B = %02x, C = %02x\n", rtcin(RTC_YEAR), rtcin(RTC_MONTH), rtcin(RTC_DAY), rtcin(RTC_HRS), rtcin(RTC_MIN), rtcin(RTC_SEC), rtcin(RTC_STATUSA), rtcin(RTC_STATUSB), rtcin(RTC_INTR)); } #endif static int getit(void) { int high, low; disable_intr(); /* select timer0 and latch counter value */ outb(TIMER_MODE, TIMER_SEL0); low = inb(TIMER_CNTR0); high = inb(TIMER_CNTR0); enable_intr(); return ((high << 8) | low); } #if defined(I586_CPU) || defined(I686_CPU) /* * Figure out how fast the cyclecounter runs. This must be run with * clock interrupts disabled, but with the timer/counter programmed * and running. */ void calibrate_cyclecounter(void) { /* * Don't need volatile; should always use unsigned if 2's * complement arithmetic is desired. */ unsigned long long count; #define howlong 131072UL __asm __volatile(".byte 0x0f, 0x30" : : "A"(0LL), "c" (0x10)); DELAY(howlong); __asm __volatile(".byte 0xf,0x31" : "=A" (count)); i586_ctr_rate = (count << I586_CTR_RATE_SHIFT) / howlong; #undef howlong } #endif /* * Wait "n" microseconds. * Relies on timer 1 counting down from (TIMER_FREQ / hz) * Note: timer had better have been programmed before this is first used! */ void DELAY(int n) { int prev_tick, tick, ticks_left, sec, usec; #ifdef DELAYDEBUG int getit_calls = 1; int n1; static int state = 0; if (state == 0) { state = 1; for (n1 = 1; n1 <= 10000000; n1 *= 10) DELAY(n1); state = 2; } if (state == 1) printf("DELAY(%d)...", n); #endif /* * Read the counter first, so that the rest of the setup overhead is * counted. Guess the initial overhead is 20 usec (on most systems it * takes about 1.5 usec for each of the i/o's in getit(). The loop * takes about 6 usec on a 486/33 and 13 usec on a 386/20. The * multiplications and divisions to scale the count take a while). */ prev_tick = getit(); n -= 20; /* * Calculate (n * (TIMER_FREQ / 1e6)) without using floating point * and without any avoidable overflows. */ sec = n / 1000000; usec = n - sec * 1000000; ticks_left = sec * TIMER_FREQ + usec * (TIMER_FREQ / 1000000) + usec * ((TIMER_FREQ % 1000000) / 1000) / 1000 + usec * (TIMER_FREQ % 1000) / 1000000; while (ticks_left > 0) { tick = getit(); #ifdef DELAYDEBUG ++getit_calls; #endif if (tick > prev_tick) ticks_left -= prev_tick - (tick - timer0_max_count); else ticks_left -= prev_tick - tick; prev_tick = tick; } #ifdef DELAYDEBUG if (state == 1) printf(" %d calls to getit() at %d usec each\n", getit_calls, (n + 5) / getit_calls); #endif } static void sysbeepstop(void *chan) { outb(IO_PPI, inb(IO_PPI)&0xFC); /* disable counter2 output to speaker */ release_timer2(); beeping = 0; } int sysbeep(int pitch, int period) { if (acquire_timer2(TIMER_SQWAVE|TIMER_16BIT)) return -1; disable_intr(); outb(TIMER_CNTR2, pitch); outb(TIMER_CNTR2, (pitch>>8)); enable_intr(); if (!beeping) { outb(IO_PPI, inb(IO_PPI) | 3); /* enable counter2 output to speaker */ beeping = period; timeout(sysbeepstop, (void *)NULL, period); } return 0; } /* * RTC support routines */ static int bcd2int(int bcd) { return(bcd/16 * 10 + bcd%16); } static int int2bcd(int dez) { return(dez/10 * 16 + dez%10); } static inline void writertc(u_char reg, u_char val) { outb(IO_RTC, reg); outb(IO_RTC + 1, val); } static int readrtc(int port) { return(bcd2int(rtcin(port))); } /* * Initialize 8253 timer 0 early so that it can be used in DELAY(). * XXX initialization of other timers is unintentionally left blank. */ void startrtclock() { timer0_max_count = hardclock_max_count = TIMER_DIV(hz); timer0_overflow_threshold = timer0_max_count - TIMER0_LATCH_COUNT; outb(TIMER_MODE, TIMER_SEL0 | TIMER_RATEGEN | TIMER_16BIT); outb(TIMER_CNTR0, timer0_max_count & 0xff); outb(TIMER_CNTR0, timer0_max_count >> 8); } /* * Initialize the time of day register, based on the time base which is, e.g. * from a filesystem. */ void inittodr(time_t base) { unsigned long sec, days; int yd; int year, month; int y, m, s; s = splclock(); time.tv_sec = base; time.tv_usec = 0; splx(s); /* Look if we have a RTC present and the time is valid */ if (!(rtcin(RTC_STATUSD) & RTCSD_PWR)) goto wrong_time; /* wait for time update to complete */ /* If RTCSA_TUP is zero, we have at least 244us before next update */ while (rtcin(RTC_STATUSA) & RTCSA_TUP); days = 0; #ifdef USE_RTC_CENTURY year = readrtc(RTC_YEAR) + readrtc(RTC_CENTURY) * 100; #else year = readrtc(RTC_YEAR) + 1900; if (year < 1970) year += 100; #endif if (year < 1970) goto wrong_time; month = readrtc(RTC_MONTH); for (m = 1; m < month; m++) days += daysinmonth[m-1]; if ((month > 2) && LEAPYEAR(year)) days ++; days += readrtc(RTC_DAY) - 1; yd = days; for (y = 1970; y < year; y++) days += DAYSPERYEAR + LEAPYEAR(y); sec = ((( days * 24 + readrtc(RTC_HRS)) * 60 + readrtc(RTC_MIN)) * 60 + readrtc(RTC_SEC)); /* sec now contains the number of seconds, since Jan 1 1970, in the local time zone */ sec += tz.tz_minuteswest * 60 + adjkerntz; s = splclock(); time.tv_sec = sec; splx(s); return; wrong_time: printf("Invalid time in real time clock.\n"); printf("Check and reset the date immediately!\n"); } /* * Write system time back to RTC */ void resettodr() { unsigned long tm; int y, m, s; if (disable_rtc_set) return; s = splclock(); tm = time.tv_sec; splx(s); /* Disable RTC updates and interrupts. */ writertc(RTC_STATUSB, RTCSB_HALT | RTCSB_24HR); /* Calculate local time to put in RTC */ tm -= tz.tz_minuteswest * 60 + adjkerntz; writertc(RTC_SEC, int2bcd(tm%60)); tm /= 60; /* Write back Seconds */ writertc(RTC_MIN, int2bcd(tm%60)); tm /= 60; /* Write back Minutes */ writertc(RTC_HRS, int2bcd(tm%24)); tm /= 24; /* Write back Hours */ /* We have now the days since 01-01-1970 in tm */ writertc(RTC_WDAY, (tm+4)%7); /* Write back Weekday */ for (y=1970;; y++) if ((tm - DAYSPERYEAR - LEAPYEAR(y)) > tm) break; else tm -= DAYSPERYEAR + LEAPYEAR(y); /* Now we have the years in y and the day-of-the-year in tm */ writertc(RTC_YEAR, int2bcd(y%100)); /* Write back Year */ #ifdef USE_RTC_CENTURY writertc(RTC_CENTURY, int2bcd(y/100)); /* ... and Century */ #endif if (LEAPYEAR(y) && (tm >= 31+29)) tm--; /* Subtract Feb-29 */ for (m=1;; m++) if (tm - daysinmonth[m-1] > tm) break; else tm -= daysinmonth[m-1]; writertc(RTC_MONTH, int2bcd(m)); /* Write back Month */ writertc(RTC_DAY, int2bcd(tm+1)); /* Write back Day */ /* Reenable RTC updates and interrupts. */ writertc(RTC_STATUSB, RTCSB_24HR | RTCSB_PINTR); } /* * Start both clocks running. */ void cpu_initclocks() { int diag; stathz = RTC_NOPROFRATE; profhz = RTC_PROFRATE; /* Finish initializing 8253 timer 0. */ register_intr(/* irq */ 0, /* XXX id */ 0, /* flags */ 0, /* XXX */ (inthand2_t *)clkintr, &clk_imask, /* unit */ 0); INTREN(IRQ0); #if defined(I586_CPU) || defined(I686_CPU) /* * Finish setting up anti-jitter measures. */ if (i586_ctr_rate) { I586_CYCLECTR(i586_last_tick); i586_ctr_bias = i586_last_tick; } #endif /* Initialize RTC. */ writertc(RTC_STATUSA, rtc_statusa); writertc(RTC_STATUSB, RTCSB_24HR); diag = rtcin(RTC_DIAG); if (diag != 0) printf("RTC BIOS diagnostic error %b\n", diag, RTCDG_BITS); register_intr(/* irq */ 8, /* XXX id */ 1, /* flags */ 0, /* XXX */ (inthand2_t *)rtcintr, &stat_imask, /* unit */ 0); INTREN(IRQ8); writertc(RTC_STATUSB, RTCSB_24HR | RTCSB_PINTR); } void setstatclockrate(int newhz) { if (newhz == RTC_PROFRATE) rtc_statusa = RTCSA_DIVIDER | RTCSA_PROF; else rtc_statusa = RTCSA_DIVIDER | RTCSA_NOPROF; writertc(RTC_STATUSA, rtc_statusa); }