Updating Information for FreeBSD current users This file is maintained and copyrighted by M. Warner Losh . See end of file for further details. For commonly done items, please see the COMMON ITEMS: section later in the file. Items affecting the ports and packages system can be found in /usr/ports/UPDATING. Please read that file before running portupgrade. NOTE TO PEOPLE WHO THINK THAT FreeBSD 8.x IS SLOW: FreeBSD 8.x has many debugging features turned on, in both the kernel and userland. These features attempt to detect incorrect use of system primitives, and encourage loud failure through extra sanity checking and fail stop semantics. They also substantially impact system performance. If you want to do performance measurement, benchmarking, and optimization, you'll want to turn them off. This includes various WITNESS- related kernel options, INVARIANTS, malloc debugging flags in userland, and various verbose features in the kernel. Many developers choose to disable these features on build machines to maximize performance. (To disable malloc debugging, run ln -s aj /etc/malloc.conf.) 20090407: The size of structs vnet_net, vnet_inet and vnet_ipfw has changed; kernel modules referencing any of the above need to be recompiled. Bump __FreeBSD_version to 800075. 20090320: GEOM_PART has become the default partition slicer for storage devices, replacing GEOM_MBR, GEOM_BSD, GEOM_PC98 and GEOM_GPT slicers. It introduces some changes: MSDOS/EBR: the devices created from MSDOS extended partition entries (EBR) can be named differently than with GEOM_MBR and are now symlinks to devices with offset-based names. fstabs may need to be modified. BSD: the "geometry does not match label" warning is harmless in most cases but it points to problems in file system misalignment with disk geometry. The "c" partition is now implicit, covers the whole top-level drive and cannot be (mis)used by users. General: Kernel dumps are now not allowed to be written to devices whose partition types indicate they are meant to be used for file systems (or, in case of MSDOS partitions, as something else than the "386BSD" type). Most of these changes date approximately from 200812. 20090319: The uscanner(4) driver has been removed from the kernel. This follows Linux removing theirs in 2.6 and making libusb the default interface (supported by sane). 20090319: The multicast forwarding code has been cleaned up. netstat(1) only relies on KVM now for printing bandwidth upcall meters. The IPv4 and IPv6 modules are split into ip_mroute_mod and ip6_mroute_mod respectively. The config(5) options for statically compiling this code remain the same, i.e. 'options MROUTING'. 20090315: Support for the IFF_NEEDSGIANT network interface flag has been removed, which means that non-MPSAFE network device drivers are no longer supported. In particular, if_ar, if_sr, and network device drivers from the old (legacy) USB stack can no longer be built or used. 20090313: POSIX.1 Native Language Support (NLS) has been enabled in libc and a bunch of new language catalog files have also been added. This means that some common libc messages are now localized and they depend on the LC_MESSAGES environmental variable. 20090313: The k8temp(4) driver has been renamed to amdtemp(4) since support for K10 and K11 CPU families was added. 20090309: IGMPv3 and Source-Specific Multicast (SSM) have been merged to the IPv4 stack. VIMAGE hooks are in but not yet used. For kernel developers, the most important changes are that the ip_output() and ip_input() paths no longer take the IN_MULTI_LOCK(), and this lock has been downgraded to a non-recursive mutex. Transport protocols (UDP, Raw IP) are now responsible for filtering inbound multicast traffic according to group membership and source filters. The imo_multicast_filter() KPI exists for this purpose. Transports which do not use multicast (SCTP, TCP) already reject multicast by default. Forwarding and receive performance may improve as a mutex acquisition is no longer needed in the ip_input() low-level input path. in_addmulti() and in_delmulti() are shimmed to new KPIs which exist to support SSM in-kernel. For application developers, it is recommended that loopback of multicast datagrams be disabled for best performance, as this will still cause the lock to be taken for each looped-back datagram transmission. The net.inet.ip.mcast.loop sysctl may be tuned to 0 to disable loopback by default; it defaults to 1 to preserve the existing behaviour. For systems administrators, to obtain best performance with multicast reception and multiple groups, it is always recommended that a card with a suitably precise hash filter is used. Hash collisions will still result in the lock being taken within the transport protocol input path to check group membership. If deploying FreeBSD in an environment with IGMP snooping switches, it is recommended that the net.inet.igmp.sendlocal sysctl remain enabled; this forces 224.0.0.0/24 group membership to be announced via IGMP. The size of 'struct igmpstat' has changed; netstat needs to be recompiled to reflect this. Bump __FreeBSD_version to 800070. 20090309: libusb20.so.1 is now installed as libusb.so.1 and the ports system updated to use it. This requires a buildworld/installworld in order to update the library and dependencies (usbconfig, etc). Its advisable to rebuild all ports which uses libusb. More specific directions are given in the ports collection UPDATING file. Any /etc/libmap.conf entries for libusb are no longer required and can be removed. 20090302: A workaround is committed to allow the creation of System V shared memory segment of size > 2 GB on the 64-bit architectures. Due to a limitation of the existing ABI, the shm_segsz member of the struct shmid_ds, returned by shmctl(IPC_STAT) call is wrong for large segments. Note that limits must be explicitely raised to allow such segments to be created. 20090301: The layout of struct ifnet has changed, requiring a rebuild of all network device driver modules. 20090227: The /dev handling for the new USB stack has changed, a buildworld/installworld is required for libusb20. 20090223: The new USB2 stack has now been permanently moved in and all kernel and module names reverted to their previous values (eg, usb, ehci, ohci, ums, ...). The old usb stack can be compiled in by prefixing the name with the letter 'o', the old usb modules have been removed. Updating entry 20090216 for xorg and 20090215 for libmap may still apply. 20090217: The rc.conf(5) option if_up_delay has been renamed to defaultroute_delay to better reflect its purpose. If you have customized this setting in /etc/rc.conf you need to update it to use the new name. 20090216: xorg 7.4 wants to configure its input devices via hald which does not yet work with USB2. If the keyboard/mouse does not work in xorg then add Option "AllowEmptyInput" "off" to your ServerLayout section. This will cause X to use the configured kbd and mouse sections from your xorg.conf. 20090215: The GENERIC kernels for all architectures now default to the new USB2 stack. No kernel config options or code have been removed so if a problem arises please report it and optionally revert to the old USB stack. If you are loading USB kernel modules or have a custom kernel that includes GENERIC then ensure that usb names are also changed over, eg uftdi -> usb2_serial_ftdi. Older programs linked against the ports libusb 0.1 need to be redirected to the new stack's libusb20. /etc/libmap.conf can be used for this: # Map old usb library to new one for usb2 stack libusb-0.1.so.8 libusb20.so.1 20090203: The ichsmb(4) driver has been changed to require SMBus slave addresses be left-justified (xxxxxxx0b) rather than right-justified. All of the other SMBus controller drivers require left-justified slave addresses, so this change makes all the drivers provide the same interface. 20090201: INET6 statistics (struct ip6stat) was updated. netstat(1) needs to be recompiled. 20090119: NTFS has been removed from GENERIC kernel on amd64 to match GENERIC on i386. Should not cause any issues since mount_ntfs(8) will load ntfs.ko module automatically when NTFS support is actually needed, unless ntfs.ko is not installed or security level prohibits loading kernel modules. If either is the case, "options NTFS" has to be added into kernel config. 20090115: TCP Appropriate Byte Counting (RFC 3465) support added to kernel. New field in struct tcpcb breaks ABI, so bump __FreeBSD_version to 800061. User space tools that rely on the size of struct tcpcb in tcp_var.h (e.g. sockstat) need to be recompiled. 20081225: ng_tty(4) module updated to match the new TTY subsystem. Due to API change, user-level applications must be updated. New API support added to mpd5 CVS and expected to be present in next mpd5.3 release. 20081219: With __FreeBSD_version 800060 the makefs tool is part of the base system (it was a port). 20081216: The afdata and ifnet locks have been changed from mutexes to rwlocks, network modules will need to be re-compiled. 20081214: __FreeBSD_version 800059 incorporates the new arp-v2 rewrite. RTF_CLONING, RTF_LLINFO and RTF_WASCLONED flags are eliminated. The new code reduced struct rtentry{} by 16 bytes on 32-bit architecture and 40 bytes on 64-bit architecture. The userland applications "arp" and "ndp" have been updated accordingly. The output from "netstat -r" shows only routing entries and none of the L2 information. 20081130: __FreeBSD_version 800057 marks the switchover from the binary ath hal to source code. Users must add the line: options AH_SUPPORT_AR5416 to their kernel config files when specifying: device ath_hal The ath_hal module no longer exists; the code is now compiled together with the driver in the ath module. It is now possible to tailor chip support (i.e. reduce the set of chips and thereby the code size); consult ath_hal(4) for details. 20081121: __FreeBSD_version 800054 adds memory barriers to , new interfaces to ifnet to facilitate multiple hardware transmit queues for cards that support them, and a lock-less ring-buffer implementation to enable drivers to more efficiently manage queueing of packets. 20081117: A new version of ZFS (version 13) has been merged to -HEAD. This version has zpool attribute "listsnapshots" off by default, which means "zfs list" does not show snapshots, and is the same as Solaris behavior. 20081028: dummynet(4) ABI has changed. ipfw(8) needs to be recompiled. 20081009: The uhci, ohci, ehci and slhci USB Host controller drivers have been put into separate modules. If you load the usb module separately through loader.conf you will need to load the appropriate *hci module as well. E.g. for a UHCI-based USB 2.0 controller add the following to loader.conf: uhci_load="YES" ehci_load="YES" 20081009: The ABI used by the PMC toolset has changed. Please keep userland (libpmc(3)) and the kernel module (hwpmc(4)) in sync. 20080820: The TTY subsystem of the kernel has been replaced by a new implementation, which provides better scalability and an improved driver model. Most common drivers have been migrated to the new TTY subsystem, while others have not. The following drivers have not yet been ported to the new TTY layer: PCI/ISA: cy, digi, rc, rp, sio USB: ubser, ucycom Line disciplines: ng_h4, ng_tty, ppp, sl, snp Adding these drivers to your kernel configuration file shall cause compilation to fail. 20080818: ntpd has been upgraded to 4.2.4p5. 20080801: OpenSSH has been upgraded to 5.1p1. For many years, FreeBSD's version of OpenSSH preferred DSA over RSA for host and user authentication keys. With this upgrade, we've switched to the vendor's default of RSA over DSA. This may cause upgraded clients to warn about unknown host keys even for previously known hosts. Users should follow the usual procedure for verifying host keys before accepting the RSA key. This can be circumvented by setting the "HostKeyAlgorithms" option to "ssh-dss,ssh-rsa" in ~/.ssh/config or on the ssh command line. Please note that the sequence of keys offered for authentication has been changed as well. You may want to specify IdentityFile in a different order to revert this behavior. 20080713: The sio(4) driver has been removed from the i386 and amd64 kernel configuration files. This means uart(4) is now the default serial port driver on those platforms as well. To prevent collisions with the sio(4) driver, the uart(4) driver uses different names for its device nodes. This means the onboard serial port will now most likely be called "ttyu0" instead of "ttyd0". You may need to reconfigure applications to use the new device names. When using the serial port as a boot console, be sure to update /boot/device.hints and /etc/ttys before booting the new kernel. If you forget to do so, you can still manually specify the hints at the loader prompt: set hint.uart.0.at="isa" set hint.uart.0.port="0x3F8" set hint.uart.0.flags="0x10" set hint.uart.0.irq="4" boot -s 20080609: The gpt(8) utility has been removed. Use gpart(8) to partition disks instead. 20080603: The version that Linuxulator emulates was changed from 2.4.2 to 2.6.16. If you experience any problems with Linux binaries please try to set sysctl compat.linux.osrelease to 2.4.2 and if it fixes the problem contact emulation mailing list. 20080525: ISDN4BSD (I4B) was removed from the src tree. You may need to update a your kernel configuration and remove relevant entries. 20080509: I have checked in code to support multiple routing tables. See the man pages setfib(1) and setfib(2). This is a hopefully backwards compatible version, but to make use of it you need to compile your kernel with options ROUTETABLES=2 (or more up to 16). 20080420: The 802.11 wireless support was redone to enable multi-bss operation on devices that are capable. The underlying device is no longer used directly but instead wlanX devices are cloned with ifconfig. This requires changes to rc.conf files. For example, change: ifconfig_ath0="WPA DHCP" to wlans_ath0=wlan0 ifconfig_wlan0="WPA DHCP" see rc.conf(5) for more details. In addition, mergemaster of /etc/rc.d is highly recommended. Simultaneous update of userland and kernel wouldn't hurt either. As part of the multi-bss changes the wlan_scan_ap and wlan_scan_sta modules were merged into the base wlan module. All references to these modules (e.g. in kernel config files) must be removed. 20080408: psm(4) has gained write(2) support in native operation level. Arbitrary commands can be written to /dev/psm%d and status can be read back from it. Therefore, an application is responsible for status validation and error recovery. It is a no-op in other operation levels. 20080312: Support for KSE threading has been removed from the kernel. To run legacy applications linked against KSE libmap.conf may be used. The following libmap.conf may be used to ensure compatibility with any prior release: libpthread.so.1 libthr.so.1 libpthread.so.2 libthr.so.2 libkse.so.3 libthr.so.3 20080301: The layout of struct vmspace has changed. This affects libkvm and any executables that link against libkvm and use the kvm_getprocs() function. In particular, but not exclusively, it affects ps(1), fstat(1), pkill(1), systat(1), top(1) and w(1). The effects are minimal, but it's advisable to upgrade world nonetheless. 20080229: The latest em driver no longer has support in it for the 82575 adapter, this is now moved to the igb driver. The split was done to make new features that are incompatible with older hardware easier to do. 20080220: The new geom_lvm(4) geom class has been renamed to geom_linux_lvm(4), likewise the kernel option is now GEOM_LINUX_LVM. 20080211: The default NFS mount mode has changed from UDP to TCP for increased reliability. If you rely on (insecurely) NFS mounting across a firewall you may need to update your firewall rules. 20080208: Belatedly note the addition of m_collapse for compacting mbuf chains. 20080126: The fts(3) structures have been changed to use adequate integer types for their members and so to be able to cope with huge file trees. The old fts(3) ABI is preserved through symbol versioning in libc, so third-party binaries using fts(3) should still work, although they will not take advantage of the extended types. At the same time, some third-party software might fail to build after this change due to unportable assumptions made in its source code about fts(3) structure members. Such software should be fixed by its vendor or, in the worst case, in the ports tree. FreeBSD_version 800015 marks this change for the unlikely case that a portable fix is impossible. 20080123: To upgrade to -current after this date, you must be running FreeBSD not older than 6.0-RELEASE. Upgrading to -current from 5.x now requires a stop over at RELENG_6 or RELENG_7 systems. 20071128: The ADAPTIVE_GIANT kernel option has been retired because its functionality is the default now. 20071118: The AT keyboard emulation of sunkbd(4) has been turned on by default. In order to make the special symbols of the Sun keyboards driven by sunkbd(4) work under X these now have to be configured the same way as Sun USB keyboards driven by ukbd(4) (which also does AT keyboard emulation), f.e.: Option "XkbLayout" "us" Option "XkbRules" "xorg" Option "XkbSymbols" "pc(pc105)+sun_vndr/usb(sun_usb)+us" 20071024: It has been decided that it is desirable to provide ABI backwards compatibility to the FreeBSD 4/5/6 versions of the PCIOCGETCONF, PCIOCREAD and PCIOCWRITE IOCTLs, which was broken with the introduction of PCI domain support (see the 20070930 entry). Unfortunately, this required the ABI of PCIOCGETCONF to be broken again in order to be able to provide backwards compatibility to the old version of that IOCTL. Thus consumers of PCIOCGETCONF have to be recompiled again. As for prominent ports this affects neither pciutils nor xorg-server this time, the hal port needs to be rebuilt however. 20071020: The misnamed kthread_create() and friends have been renamed to kproc_create() etc. Many of the callers already used kproc_start().. I will return kthread_create() and friends in a while with implementations that actually create threads, not procs. Renaming corresponds with version 800002. 20071010: RELENG_7 branched. 20071009: Setting WITHOUT_LIBPTHREAD now means WITHOUT_LIBKSE and WITHOUT_LIBTHR are set. 20070930: The PCI code has been made aware of PCI domains. This means that the location strings as used by pciconf(8) etc are now in the following format: pci::[:]. It also means that consumers of potentially need to be recompiled; this includes the hal and xorg-server ports. 20070928: The caching daemon (cached) was renamed to nscd. nscd.conf configuration file should be used instead of cached.conf and nscd_enable, nscd_pidfile and nscd_flags options should be used instead of cached_enable, cached_pidfile and cached_flags in rc.conf. 20070921: The getfacl(1) utility now prints owning user and group name instead of owning uid and gid in the three line comment header. This is the same behavior as getfacl(1) on Solaris and Linux. 20070704: The new IPsec code is now compiled in using the IPSEC option. The IPSEC option now requires "device crypto" be defined in your kernel configuration. The FAST_IPSEC kernel option is now deprecated. 20070702: The packet filter (pf) code has been updated to OpenBSD 4.1 Please note the changed syntax - keep state is now on by default. Also note the fact that ftp-proxy(8) has been changed from bottom up and has been moved from libexec to usr/sbin. Changes in the ALTQ handling also affect users of IPFW's ALTQ capabilities. 20070701: Remove KAME IPsec in favor of FAST_IPSEC, which is now the only IPsec supported by FreeBSD. The new IPsec stack supports both IPv4 and IPv6. The kernel option will change after the code changes have settled in. For now the kernel option IPSEC is deprecated and FAST_IPSEC is the only option, that will change after some settling time. 20070701: The wicontrol(8) utility has been removed from the base system. wi(4) cards should be configured using ifconfig(8), see the man page for more information. 20070612: The i386/amd64 GENERIC kernel now defaults to the nfe(4) driver instead of the nve(4) driver. Please update your configuration accordingly. 20070612: By default, /etc/rc.d/sendmail no longer rebuilds the aliases database if it is missing or older than the aliases file. If desired, set the new rc.conf option sendmail_rebuild_aliases to "YES" to restore that functionality. 20070612: The IPv4 multicast socket code has been considerably modified, and moved to the file sys/netinet/in_mcast.c. Initial support for the RFC 3678 Source-Specific Multicast Socket API has been added to the IPv4 network stack. Strict multicast and broadcast reception is now the default for UDP/IPv4 sockets; the net.inet.udp.strict_mcast_mship sysctl variable has now been removed. The RFC 1724 hack for interface selection has been removed; the use of the Linux-derived ip_mreqn structure with IP_MULTICAST_IF has been added to replace it. Consumers such as routed will soon be updated to reflect this. These changes affect users who are running routed(8) or rdisc(8) from the FreeBSD base system on point-to-point or unnumbered interfaces. 20070610: The net80211 layer has changed significantly and all wireless drivers that depend on it need to be recompiled. Further these changes require that any program that interacts with the wireless support in the kernel be recompiled; this includes: ifconfig, wpa_supplicant, hostapd, and wlanstats. Users must also, for the moment, kldload the wlan_scan_sta and/or wlan_scan_ap modules if they use modules for wireless support. These modules implement scanning support for station and ap modes, respectively. Failure to load the appropriate module before marking a wireless interface up will result in a message to the console and the device not operating properly. 20070610: The pam_nologin(8) module ceases to provide an authentication function and starts providing an account management function. Consequent changes to /etc/pam.d should be brought in using mergemaster(8). Third-party files in /usr/local/etc/pam.d may need manual editing as follows. Locate this line (or similar): auth required pam_nologin.so no_warn and change it according to this example: account required pam_nologin.so no_warn That is, the first word needs to be changed from "auth" to "account". The new line can be moved to the account section within the file for clarity. Not updating pam.conf(5) files will result in nologin(5) ignored by the respective services. 20070529: The ether_ioctl() function has been synchronized with ioctl(2) and ifnet.if_ioctl. Due to that, the size of one of its arguments has changed on 64-bit architectures. All kernel modules using ether_ioctl() need to be rebuilt on such architectures. 20070516: Improved INCLUDE_CONFIG_FILE support has been introduced to the config(8) utility. In order to take advantage of this new functionality, you are expected to recompile and install src/usr.sbin/config. If you don't rebuild config(8), and your kernel configuration depends on INCLUDE_CONFIG_FILE, the kernel build will be broken because of a missing "kernconfstring" symbol. 20070513: Symbol versioning is enabled by default. To disable it, use option WITHOUT_SYMVER. It is not advisable to attempt to disable symbol versioning once it is enabled; your installworld will break because a symbol version-less libc will get installed before the install tools. As a result, the old install tools, which previously had symbol dependencies to FBSD_1.0, will fail because the freshly installed libc will not have them. The default threading library (providing "libpthread") has been changed to libthr. If you wish to have libkse as your default, use option DEFAULT_THREAD_LIB=libkse for the buildworld. 20070423: The ABI breakage in sendmail(8)'s libmilter has been repaired so it is no longer necessary to recompile mail filters (aka, milters). If you recompiled mail filters after the 20070408 note, it is not necessary to recompile them again. 20070417: The new trunk(4) driver has been renamed to lagg(4) as it better reflects its purpose. ifconfig will need to be recompiled. 20070408: sendmail(8) has been updated to version 8.14.1. Mail filters (aka, milters) compiled against the libmilter included in the base operating system should be recompiled. 20070302: Firmwares for ipw(4) and iwi(4) are now included in the base tree. In order to use them one must agree to the respective LICENSE in share/doc/legal and define legal.intel_.license_ack=1 via loader.conf(5) or kenv(1). Make sure to deinstall the now deprecated modules from the respective firmware ports. 20070228: The name resolution/mapping functions addr2ascii(3) and ascii2addr(3) were removed from FreeBSD's libc. These originally came from INRIA IPv6. Nothing in FreeBSD ever used them. They may be regarded as deprecated in previous releases. The AF_LINK support for getnameinfo(3) was merged from NetBSD to replace it as a more portable (and re-entrant) API. 20070224: To support interrupt filtering a modification to the newbus API has occurred, ABI was broken and __FreeBSD_version was bumped to 700031. Please make sure that your kernel and modules are in sync. For more info: http://docs.freebsd.org/cgi/mid.cgi?20070221233124.GA13941 20070224: The IPv6 multicast forwarding code may now be loaded into GENERIC kernels by loading the ip_mroute.ko module. This is built into the module unless WITHOUT_INET6 or WITHOUT_INET6_SUPPORT options are set; see src.conf(5) for more information. 20070214: The output of netstat -r has changed. Without -n, we now only print a "network name" without the prefix length if the network address and mask exactly match a Class A/B/C network, and an entry exists in the nsswitch "networks" map. With -n, we print the full unabbreviated CIDR network prefix in the form "a.b.c.d/p". 0.0.0.0/0 is always printed as "default". This change is in preparation for changes such as equal-cost multipath, and to more generally assist operational deployment of FreeBSD as a modern IPv4 router. 20070210: PIM has been turned on by default in the IPv4 multicast routing code. The kernel option 'PIM' has now been removed. PIM is now built by default if option 'MROUTING' is specified. It may now be loaded into GENERIC kernels by loading the ip_mroute.ko module. 20070207: Support for IPIP tunnels (VIFF_TUNNEL) in IPv4 multicast routing has been removed. Its functionality may be achieved by explicitly configuring gif(4) interfaces and using the 'phyint' keyword in mrouted.conf. XORP does not support source-routed IPv4 multicast tunnels nor the integrated IPIP tunneling, therefore it is not affected by this change. The __FreeBSD_version macro has been bumped to 700030. 20061221: Support for PCI Message Signalled Interrupts has been re-enabled in the bge driver, only for those chips which are believed to support it properly. If there are any problems, MSI can be disabled completely by setting the 'hw.pci.enable_msi' and 'hw.pci.enable_msix' tunables to 0 in the loader. 20061214: Support for PCI Message Signalled Interrupts has been disabled again in the bge driver. Many revisions of the hardware fail to support it properly. Support can be re-enabled by removing the #define of BGE_DISABLE_MSI in "src/sys/dev/bge/if_bge.c". 20061214: Support for PCI Message Signalled Interrupts has been added to the bge driver. If there are any problems, MSI can be disabled completely by setting the 'hw.pci.enable_msi' and 'hw.pci.enable_msix' tunables to 0 in the loader. 20061205: The removal of several facets of the experimental Threading system from the kernel means that the proc and thread structures have changed quite a bit. I suggest all kernel modules that might reference these structures be recompiled.. Especially the linux module. 20061126: Sound infrastructure has been updated with various fixes and improvements. Most of the changes are pretty much transparent, with exceptions of followings: 1) All sound driver specific sysctls (hw.snd.pcm%d.*) have been moved to their own dev sysctl nodes, for example: hw.snd.pcm0.vchans -> dev.pcm.0.vchans 2) /dev/dspr%d.%d has been deprecated. Each channel now has its own chardev in the form of "dsp%d.%d", where is p = playback, r = record and v = virtual, respectively. Users are encouraged to use these devs instead of (old) "/dev/dsp%d.%d". This does not affect those who are using "/dev/dsp". 20061122: geom(4)'s gmirror(8) class metadata structure has been rev'd from v3 to v4. If you update across this point and your metadata is converted for you, you will not be easily able to downgrade since the /boot/kernel.old/geom_mirror.ko kernel module will be unable to read the v4 metadata. You can resolve this by doing from the loader(8) prompt: set vfs.root.mountfrom="ufs:/dev/XXX" where XXX is the root slice of one of the disks that composed the mirror (i.e.: /dev/ad0s1a). You can then rebuild the array the same way you built it originally. 20061122: The following binaries have been disconnected from the build: mount_devfs, mount_ext2fs, mount_fdescfs, mount_procfs, mount_linprocfs, and mount_std. The functionality of these programs has been moved into the mount program. For example, to mount a devfs filesystem, instead of using mount_devfs, use: "mount -t devfs". This does not affect entries in /etc/fstab, since entries in /etc/fstab are always processed with "mount -t fstype". 20061113: Support for PCI Message Signalled Interrupts on i386 and amd64 has been added to the kernel and various drivers will soon be updated to use MSI when it is available. If there are any problems, MSI can be disabled completely by setting the 'hw.pci.enable_msi' and 'hw.pci.enable_msix' tunables to 0 in the loader. 20061110: The MUTEX_PROFILING option has been renamed to LOCK_PROFILING. The lockmgr object layout has been changed as a result of having a lock_object embedded in it. As a consequence all file system kernel modules must be re-compiled. The mutex profiling man page has not yet been updated to reflect this change. 20061026: KSE in the kernel has now been made optional and turned on by default. Use 'nooption KSE' in your kernel config to turn it off. All kernel modules *must* be recompiled after this change. There-after, modules from a KSE kernel should be compatible with modules from a NOKSE kernel due to the temporary padding fields added to 'struct proc'. 20060929: mrouted and its utilities have been removed from the base system. 20060927: Some ioctl(2) command codes have changed. Full backward ABI compatibility is provided if the "options COMPAT_FREEBSD6" is present in the kernel configuration file. Make sure to add this option to your kernel config file, or recompile X.Org and the rest of ports; otherwise they may refuse to work. 20060924: tcpslice has been removed from the base system. 20060913: The sizes of struct tcpcb (and struct xtcpcb) have changed due to the rewrite of TCP syncookies. Tools like netstat, sockstat, and systat needs to be rebuilt. 20060903: libpcap updated to v0.9.4 and tcpdump to v3.9.4 20060816: The IPFIREWALL_FORWARD_EXTENDED option is gone and the behaviour for IPFIREWALL_FORWARD is now as it was before when it was first committed and for years after. The behaviour is now ON. 20060725: enigma(1)/crypt(1) utility has been changed on 64 bit architectures. Now it can decrypt files created from different architectures. Unfortunately, it is no longer able to decrypt a cipher text generated with an older version on 64 bit architectures. If you have such a file, you need old utility to decrypt it. 20060709: The interface version of the i4b kernel part has changed. So after updating the kernel sources and compiling a new kernel, the i4b user space tools in "/usr/src/usr.sbin/i4b" must also be rebuilt, and vice versa. 20060627: The XBOX kernel now defaults to the nfe(4) driver instead of the nve(4) driver. Please update your configuration accordingly. 20060514: The i386-only lnc(4) driver for the AMD Am7900 LANCE and Am79C9xx PCnet family of NICs has been removed. The new le(4) driver serves as an equivalent but cross-platform replacement with the pcn(4) driver still providing performance-optimized support for the subset of AMD Am79C971 PCnet-FAST and greater chips as before. 20060511: The machdep.* sysctls and the adjkerntz utility have been modified a bit. The new adjkerntz utility uses the new sysctl names and sysctlbyname() calls, so it may be impossible to run an old /sbin/adjkerntz utility in single-user mode with a new kernel. Replace the `adjkerntz -i' step before `make installworld' with: /usr/obj/usr/src/sbin/adjkerntz/adjkerntz -i and proceed as usual with the rest of the installworld-stage steps. Otherwise, you risk installing binaries with their timestamp set several hours in the future, especially if you are running with local time set to GMT+X hours. 20060412: The ip6fw utility has been removed. The behavior provided by ip6fw has been in ipfw2 for a good while and the rc.d scripts have been updated to deal with it. There are some rules that might not migrate cleanly. Use rc.firewall6 as a template to rewrite rules. 20060428: The puc(4) driver has been overhauled. The ebus(4) and sbus(4) attachments have been removed. Make sure to configure scc(4) on sparc64. Note also that by default puc(4) will use uart(4) and not sio(4) for serial ports because interrupt handling has been optimized for multi-port serial cards and only uart(4) implements the interface to support it. 20060330: The scc(4) driver replaces puc(4) for Serial Communications Controllers (SCCs) like the Siemens SAB82532 and the Zilog Z8530. On sparc64, it is advised to add scc(4) to the kernel configuration to make sure that the serial ports remain functional. 20060317: Most world/kernel related NO_* build options changed names. New knobs have common prefixes WITHOUT_*/WITH_* (modelled after FreeBSD ports) and should be set in /etc/src.conf (the src.conf(5) manpage is provided). Full backwards compatibility is maintained for the time being though it's highly recommended to start moving old options out of the system-wide /etc/make.conf file into the new /etc/src.conf while also properly renaming them. More conversions will likely follow. Posting to current@: http://lists.freebsd.org/pipermail/freebsd-current/2006-March/061725.html 20060305: The NETSMBCRYPTO kernel option has been retired because its functionality is always included in NETSMB and smbfs.ko now. 20060303: The TDFX_LINUX kernel option was retired and replaced by the tdfx_linux device. The latter can be loaded as the 3dfx_linux.ko kernel module. Loading it alone should suffice to get 3dfx support for Linux apps because it will pull in 3dfx.ko and linux.ko through its dependencies. 20060204: The 'audit' group was added to support the new auditing functionality in the base system. Be sure to follow the directions for updating, including the requirement to run mergemaster -p. 20060201: The kernel ABI to file system modules was changed on i386. Please make sure that your kernel and modules are in sync. 20060118: This actually occured some time ago, but installing the kernel now also installs a bunch of symbol files for the kernel modules. This increases the size of /boot/kernel to about 67Mbytes. You will need twice this if you will eventually back this up to kernel.old on your next install. If you have a shortage of room in your root partition, you should add -DINSTALL_NODEBUG to your make arguments or add INSTALL_NODEBUG="yes" to your /etc/make.conf. 20060113: libc's malloc implementation has been replaced. This change has the potential to uncover application bugs that previously went unnoticed. See the malloc(3) manual page for more details. 20060112: The generic netgraph(4) cookie has been changed. If you upgrade kernel passing this point, you also need to upgrade userland and netgraph(4) utilities like ports/net/mpd or ports/net/mpd4. 20060106: si(4)'s device files now contain the unit number. Uses of {cua,tty}A[0-9a-f] should be replaced by {cua,tty}A0[0-9a-f]. 20060106: The kernel ABI was mostly destroyed due to a change in the size of struct lock_object which is nested in other structures such as mutexes which are nested in all sorts of other structures. Make sure your kernel and modules are in sync. 20051231: The page coloring algorithm in the VM subsystem was converted from tuning with kernel options to autotuning. Please remove any PQ_* option except PQ_NOOPT from your kernel config. 20051211: The net80211-related tools in the tools/tools/ath directory have been moved to tools/tools/net80211 and renamed with a "wlan" prefix. Scripts that use them should be adjusted accordingly. 20051202: Scripts in the local_startup directories (as defined in /etc/defaults/rc.conf) that have the new rc.d semantics will now be run as part of the base system rcorder. If there are errors or problems with one of these local scripts, it could cause boot problems. If you encounter such problems, boot in single user mode, remove that script from the */rc.d directory. Please report the problem to the port's maintainer, and the freebsd-ports@freebsd.org mailing list. 20051129: The nodev mount option was deprecated in RELENG_6 (where it was a no-op), and is now unsupported. If you have nodev or dev listed in /etc/fstab, remove it, otherwise it will result in a mount error. 20051129: ABI between ipfw(4) and ipfw(8) has been changed. You need to rebuild ipfw(8) when rebuilding kernel. 20051108: rp(4)'s device files now contain the unit number. Uses of {cua,tty}R[0-9a-f] should be replaced by {cua,tty}R0[0-9a-f]. 20051029: /etc/rc.d/ppp-user has been renamed to /etc/rc.d/ppp. Its /etc/rc.conf.d configuration file has been `ppp' from the beginning, and hence there is no need to touch it. 20051014: Now most modules get their build-time options from the kernel configuration file. A few modules still have fixed options due to their non-conformant implementation, but they will be corrected eventually. You may need to review the options of the modules in use, explicitly specify the non-default options in the kernel configuration file, and rebuild the kernel and modules afterwards. 20051001: kern.polling.enable sysctl MIB is now deprecated. Use ifconfig(8) to turn polling(4) on your interfaces. 20050927: The old bridge(4) implementation was retired. The new if_bridge(4) serves as a full functional replacement. 20050722: The ai_addrlen of a struct addrinfo was changed to a socklen_t to conform to POSIX-2001. This change broke an ABI compatibility on 64 bit architecture. You have to recompile userland programs that use getaddrinfo(3) on 64 bit architecture. 20050711: RELENG_6 branched here. 20050629: The pccard_ifconfig rc.conf variable has been removed and a new variable, ifconfig_DEFAULT has been introduced. Unlike pccard_ifconfig, ifconfig_DEFAULT applies to ALL interfaces that do not have ifconfig_ifn entries rather than just those in removable_interfaces. 20050616: Some previous versions of PAM have permitted the use of non-absolute paths in /etc/pam.conf or /etc/pam.d/* when referring to third party PAM modules in /usr/local/lib. A change has been made to require the use of absolute paths in order to avoid ambiguity and dependence on library path configuration, which may affect existing configurations. 20050610: Major changes to network interface API. All drivers must be recompiled. Drivers not in the base system will need to be updated to the new APIs. 20050609: Changes were made to kinfo_proc in sys/user.h. Please recompile userland, or commands like `fstat', `pkill', `ps', `top' and `w' will not behave correctly. The API and ABI for hwpmc(4) have changed with the addition of sampling support. Please recompile lib/libpmc(3) and usr.sbin/{pmcstat,pmccontrol}. 20050606: The OpenBSD dhclient was imported in place of the ISC dhclient and the network interface configuration scripts were updated accordingly. If you use DHCP to configure your interfaces, you must now run devd. Also, DNS updating was lost so you will need to find a workaround if you use this feature. The '_dhcp' user was added to support the OpenBSD dhclient. Be sure to run mergemaster -p (like you are supposed to do every time anyway). 20050605: if_bridge was added to the tree. This has changed struct ifnet. Please recompile userland and all network related modules. 20050603: The n_net of a struct netent was changed to an uint32_t, and 1st argument of getnetbyaddr() was changed to an uint32_t, to conform to POSIX-2001. These changes broke an ABI compatibility on 64 bit architecture. With these changes, shlib major of libpcap was bumped. You have to recompile userland programs that use getnetbyaddr(3), getnetbyname(3), getnetent(3) and/or libpcap on 64 bit architecture. 20050528: Kernel parsing of extra options on '#!' first lines of shell scripts has changed. Lines with multiple options likely will fail after this date. For full details, please see http://people.freebsd.org/~gad/Updating-20050528.txt 20050503: The packet filter (pf) code has been updated to OpenBSD 3.7 Please note the changed anchor syntax and the fact that authpf(8) now needs a mounted fdescfs(5) to function. 20050415: The NO_MIXED_MODE kernel option has been removed from the i386 amd64 platforms as its use has been superceded by the new local APIC timer code. Any kernel config files containing this option should be updated. 20050227: The on-disk format of LC_CTYPE files was changed to be machine independent. Please make sure NOT to use NO_CLEAN buildworld when crossing this point. Crossing this point also requires recompile or reinstall of all locale depended packages. 20050225: The ifi_epoch member of struct if_data has been changed to contain the uptime at which the interface was created or the statistics zeroed rather then the wall clock time because wallclock time may go backwards. This should have no impact unless an snmp implementation is using this value (I know of none at this point.) 20050224: The acpi_perf and acpi_throttle drivers are now part of the acpi(4) main module. They are no longer built separately. 20050223: The layout of struct image_params has changed. You have to recompile all compatibility modules (linux, svr4, etc) for use with the new kernel. 20050223: The p4tcc driver has been merged into cpufreq(4). This makes "options CPU_ENABLE_TCC" obsolete. Please load cpufreq.ko or compile in "device cpufreq" to restore this functionality. 20050220: The responsibility of recomputing the file system summary of a SoftUpdates-enabled dirty volume has been transferred to the background fsck. A rebuild of fsck(8) utility is recommended if you have updated the kernel. To get the old behavior (recompute file system summary at mount time), you can set vfs.ffs.compute_summary_at_mount=1 before mounting the new volume. 20050206: The cpufreq import is complete. As part of this, the sysctls for acpi(4) throttling have been removed. The power_profile script has been updated, so you can use performance/economy_cpu_freq in rc.conf(5) to set AC on/offline cpu frequencies. 20050206: NG_VERSION has been increased. Recompiling kernel (or ng_socket.ko) requires recompiling libnetgraph and userland netgraph utilities. 20050114: Support for abbreviated forms of a number of ipfw options is now deprecated. Warnings are printed to stderr indicating the correct full form when a match occurs. Some abbreviations may be supported at a later date based on user feedback. To be considered for support, abbreviations must be in use prior to this commit and unlikely to be confused with current key words. 20041221: By a popular demand, a lot of NOFOO options were renamed to NO_FOO (see bsd.compat.mk for a full list). The old spellings are still supported, but will cause annoying warnings on stderr. Make sure you upgrade properly (see the COMMON ITEMS: section later in this file). 20041219: Auto-loading of ancillary wlan modules such as wlan_wep has been temporarily disabled; you need to statically configure the modules you need into your kernel or explicitly load them prior to use. Specifically, if you intend to use WEP encryption with an 802.11 device load/configure wlan_wep; if you want to use WPA with the ath driver load/configure wlan_tkip, wlan_ccmp, and wlan_xauth as required. 20041213: The behaviour of ppp(8) has changed slightly. If lqr is enabled (``enable lqr''), older versions would revert to LCP ECHO mode on negotiation failure. Now, ``enable echo'' is required for this behaviour. The ppp version number has been bumped to 3.4.2 to reflect the change. 20041201: The wlan support has been updated to split the crypto support into separate modules. For static WEP you must configure the wlan_wep module in your system or build and install the module in place where it can be loaded (the kernel will auto-load the module when a wep key is configured). 20041201: The ath driver has been updated to split the tx rate control algorithm into a separate module. You need to include either ath_rate_onoe or ath_rate_amrr when configuring the kernel. 20041116: Support for systems with an 80386 CPU has been removed. Please use FreeBSD 5.x or earlier on systems with an 80386. 20041110: We have had a hack which would mount the root filesystem R/W if the device were named 'md*'. As part of the vnode work I'm doing I have had to remove this hack. People building systems which use preloaded MD root filesystems may need to insert a "/sbin/mount -u -o rw /dev/md0 /" in their /etc/rc scripts. 20041104: FreeBSD 5.3 shipped here. 20041102: The size of struct tcpcb has changed again due to the removal of RFC1644 T/TCP. You have to recompile userland programs that read kmem for tcp sockets directly (netstat, sockstat, etc.) 20041022: The size of struct tcpcb has changed. You have to recompile userland programs that read kmem for tcp sockets directly (netstat, sockstat, etc.) 20041016: RELENG_5 branched here. For older entries, please see updating in the RELENG_5 branch. COMMON ITEMS: General Notes ------------- Avoid using make -j when upgrading. From time to time in the past there have been problems using -j with buildworld and/or installworld. This is especially true when upgrading between "distant" versions (eg one that cross a major release boundary or several minor releases, or when several months have passed on the -current branch). Sometimes, obscure build problems are the result of environment poisoning. This can happen because the make utility reads its environment when searching for values for global variables. To run your build attempts in an "environmental clean room", prefix all make commands with 'env -i '. See the env(1) manual page for more details. When upgrading from one major version to another it is generally best to upgrade to the latest code in the currently installed branch first, then do an upgrade to the new branch. This is the best-tested upgrade path, and has the highest probability of being successful. Please try this approach before reporting problems with a major version upgrade. To build a kernel ----------------- If you are updating from a prior version of FreeBSD (even one just a few days old), you should follow this procedure. It is the most failsafe as it uses a /usr/obj tree with a fresh mini-buildworld, make kernel-toolchain make -DALWAYS_CHECK_MAKE buildkernel KERNCONF=YOUR_KERNEL_HERE make -DALWAYS_CHECK_MAKE installkernel KERNCONF=YOUR_KERNEL_HERE To test a kernel once --------------------- If you just want to boot a kernel once (because you are not sure if it works, or if you want to boot a known bad kernel to provide debugging information) run make installkernel KERNCONF=YOUR_KERNEL_HERE KODIR=/boot/testkernel nextboot -k testkernel To just build a kernel when you know that it won't mess you up -------------------------------------------------------------- This assumes you are already running a 5.X system. Replace ${arch} with the architecture of your machine (e.g. "i386", "alpha", "amd64", "ia64", "pc98", "sparc64", etc). cd src/sys/${arch}/conf config KERNEL_NAME_HERE cd ../compile/KERNEL_NAME_HERE make depend make make install If this fails, go to the "To build a kernel" section. To rebuild everything and install it on the current system. ----------------------------------------------------------- # Note: sometimes if you are running current you gotta do more than # is listed here if you are upgrading from a really old current. make buildworld make kernel KERNCONF=YOUR_KERNEL_HERE [1] [3] mergemaster -p [5] make installworld make delete-old mergemaster [4] To cross-install current onto a separate partition -------------------------------------------------- # In this approach we use a separate partition to hold # current's root, 'usr', and 'var' directories. A partition # holding "/", "/usr" and "/var" should be about 2GB in # size. make buildworld make buildkernel KERNCONF=YOUR_KERNEL_HERE make installworld DESTDIR=${CURRENT_ROOT} make distribution DESTDIR=${CURRENT_ROOT} # if newfs'd make installkernel KERNCONF=YOUR_KERNEL_HERE DESTDIR=${CURRENT_ROOT} cp /etc/fstab ${CURRENT_ROOT}/etc/fstab # if newfs'd To upgrade in-place from 5.x-stable to current ---------------------------------------------- make buildworld [9] make kernel KERNCONF=YOUR_KERNEL_HERE [8] [1] [3] mergemaster -p [5] make installworld make delete-old mergemaster -i [4] Make sure that you've read the UPDATING file to understand the tweaks to various things you need. At this point in the life cycle of current, things change often and you are on your own to cope. The defaults can also change, so please read ALL of the UPDATING entries. Also, if you are tracking -current, you must be subscribed to freebsd-current@freebsd.org. Make sure that before you update your sources that you have read and understood all the recent messages there. If in doubt, please track -stable which has much fewer pitfalls. [1] If you have third party modules, such as vmware, you should disable them at this point so they don't crash your system on reboot. [3] From the bootblocks, boot -s, and then do fsck -p mount -u / mount -a cd src adjkerntz -i # if CMOS is wall time Also, when doing a major release upgrade, it is required that you boot into single user mode to do the installworld. [4] Note: This step is non-optional. Failure to do this step can result in a significant reduction in the functionality of the system. Attempting to do it by hand is not recommended and those that pursue this avenue should read this file carefully, as well as the archives of freebsd-current and freebsd-hackers mailing lists for potential gotchas. [5] Usually this step is a noop. However, from time to time you may need to do this if you get unknown user in the following step. It never hurts to do it all the time. You may need to install a new mergemaster (cd src/usr.sbin/mergemaster && make install) after the buildworld before this step if you last updated from current before 20020224 or from -stable before 20020408. [8] In order to have a kernel that can run the 4.x binaries needed to do an installworld, you must include the COMPAT_FREEBSD4 option in your kernel. Failure to do so may leave you with a system that is hard to boot to recover. A similar kernel option COMPAT_FREEBSD5 is required to run the 5.x binaries on more recent kernels. Make sure that you merge any new devices from GENERIC since the last time you updated your kernel config file. [9] When checking out sources, you must include the -P flag to have cvs prune empty directories. If CPUTYPE is defined in your /etc/make.conf, make sure to use the "?=" instead of the "=" assignment operator, so that buildworld can override the CPUTYPE if it needs to. MAKEOBJDIRPREFIX must be defined in an environment variable, and not on the command line, or in /etc/make.conf. buildworld will warn if it is improperly defined. FORMAT: This file contains a list, in reverse chronological order, of major breakages in tracking -current. Not all things will be listed here, and it only starts on October 16, 2004. Updating files can found in previous releases if your system is older than this. Copyright information: Copyright 1998-2005 M. Warner Losh. All Rights Reserved. Redistribution, publication, translation and use, with or without modification, in full or in part, in any form or format of this document are permitted without further permission from the author. THIS DOCUMENT IS PROVIDED BY WARNER LOSH ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL WARNER LOSH BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. If you find this document useful, and you want to, you may buy the author a beer. Contact Warner Losh if you have any questions about your use of this document. $FreeBSD$