/* * FreeBSD generic NCR-5380/NCR-53C400 SCSI driver * * Copyright (C) 1994 Serge Vakulenko (vak@cronyx.ru) * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE DEVELOPERS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE DEVELOPERS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ /* * Tested on the following hardware: * Adapter: Trantor T130 * Streamer: Archive Viper 150, * CD-ROM: NEC CDR-25 */ #undef DEBUG #include "nca.h" #if NNCA > 0 #include #include #include #include #include #include #include #include #include "ioconf.h" #ifdef DEBUG # define PRINT(s) printf s #else # define PRINT(s) /*void*/ #endif #define SCB_TABLE_SIZE 8 /* start with 8 scb entries in table */ #define BLOCK_SIZE 512 /* size of READ/WRITE areas on SCSI card */ #define HOST_SCSI_ADDR 7 /* address of the adapter on the SCSI bus */ /* * Defice config flags */ #define FLAG_NOPARITY 0x01 /* disable SCSI bus parity check */ /* * ProAudioSpectrum registers */ #define PAS16_DATA 8 /* Data Register */ #define PAS16_STAT 9 /* Status Register */ #define PAS16_STAT_DREQ 0x80 /* Pseudo-DMA ready bit */ #define PAS16_REG(r) (((r) & 0xc) << 11 | ((r) & 3)) static u_char pas16_irq_magic[] = { 0, 0, 1, 2, 3, 4, 5, 6, 0, 0, 7, 8, 9, 0, 10, 11 }; /* * SCSI bus phases */ #define PHASE_MASK (CSBR_MSG | CSBR_CD | CSBR_IO) #define PHASE_DATAOUT 0 #define PHASE_DATAIN CSBR_IO #define PHASE_CMDOUT CSBR_CD #define PHASE_STATIN (CSBR_CD | CSBR_IO) #define PHASE_MSGOUT (CSBR_MSG | CSBR_CD) #define PHASE_MSGIN (CSBR_MSG | CSBR_CD | CSBR_IO) #define PHASE_NAME(ph) phase_name[(ph)>>2] #define PHASE_TO_TCR(ph) ((ph) >> 2) static char *phase_name[] = { "DATAOUT", "DATAIN", "CMDOUT", "STATIN", "Phase4?", "Phase5?", "MSGOUT", "MSGIN", }; /* * SCSI message codes */ #define MSG_COMMAND_COMPLETE 0x00 #define MSG_SAVE_POINTERS 0x02 #define MSG_RESTORE_POINTERS 0x03 #define MSG_DISCONNECT 0x04 #define MSG_ABORT 0x06 #define MSG_MESSAGE_REJECT 0x07 #define MSG_NOP 0x08 #define MSG_BUS_DEV_RESET 0x0c #define MSG_IDENTIFY(lun) (0xc0 | ((lun) & 0x7)) #define MSG_ISIDENT(m) ((m) & 0x80) /* * SCSI control block used to keep info about a scsi command */ typedef struct scb { int flags; /* status of the instruction */ #define SCB_FREE 0x00 #define SCB_ACTIVE 0x01 #define SCB_ABORTED 0x02 #define SCB_TIMEOUT 0x04 #define SCB_ERROR 0x08 #define SCB_TIMECHK 0x10 /* we have set a timeout on this one */ #define SCB_SENSE 0x20 /* sensed data available */ #define SCB_TBUSY 0x40 /* target busy */ struct scb *next; /* in free list */ struct scsi_xfer *xfer; /* the scsi_xfer for this cmd */ u_char *data; /* position in data buffer so far */ int32_t datalen; /* bytes remaining to transfer */ } scb_t; typedef enum { CTLR_NONE, CTLR_NCR_5380, CTLR_NCR_53C400, CTLR_PAS_16 } ctlr_t; /* * Data structure describing the target state. */ typedef struct { u_char busy; /* mask of busy luns at device target */ u_long perrcnt; /* counter of target parity errors */ } target_t; /* * Data structure describing current status of the scsi bus. One for each * controller card. */ typedef struct { ctlr_t type; /* Seagate or Future Domain */ char *name; /* adapter name */ /* NCR-5380 controller registers */ u_short ODR; /* (wo-0) Output Data Register */ u_short CSDR; /* (ro-0) Current SCSI Data Register */ u_short ICR; /* (rw-1) Initiator Command Register */ u_short MR; /* (rw-2) Mode Register */ u_short TCR; /* (rw-3) Target Command Register */ u_short SER; /* (wo-4) Select Enable Register */ u_short CSBR; /* (ro-4) Current SCSI Bus Status Register */ u_short BSR; /* (ro-5) Bus and Status Register */ u_short SDSR; /* (wo-5) Start DMA Send Register */ u_short SDIR; /* (wo-7) Start DMA Initiator Receive Register */ u_short RPIR; /* (ro-7) Reset Parity/Interrupt Register */ /* NCR-53C400 controller registers */ u_short CSR; /* (rw-0) Control and Status Register */ u_short CCR; /* (rw-1) Clock Counter Register */ u_short HBR; /* (rw-4) Host Buffer Register */ /* ProAudioSpectrum controller registers */ u_short PDATA; /* (rw) Pseudo-DMA Data Register */ u_short PSTAT; /* (rw) Pseudo-DMA Status Register */ u_char scsi_addr; /* our scsi address, 0..7 */ u_char scsi_id; /* our scsi id mask */ u_char parity; /* parity flag: CMD_EN_PARITY or 0 */ u_char irq; /* IRQ number used or 0 if no IRQ */ u_int timeout_active : 1; /* timeout() active (requested) */ struct scsi_link sc_link; /* struct connecting different data */ scb_t *queue; /* waiting to be issued */ scb_t *disconnected_queue; /* waiting to reconnect */ int numscb; /* number of scsi control blocks */ scb_t *free_scb; /* free scb list */ scb_t scbs[SCB_TABLE_SIZE]; target_t target[8]; /* target state data */ } adapter_t; static adapter_t ncadata[NNCA]; #define IS_BUSY(a,b) ((a)->target[(b)->xfer->sc_link->target].busy &\ (1 << (b)->xfer->sc_link->lun)) #define SET_BUSY(a,b) ((a)->target[(b)->xfer->sc_link->target].busy |=\ (1 << (b)->xfer->sc_link->lun)) #define CLEAR_BUSY(a,b) ((a)->target[(b)->xfer->sc_link->target].busy &=\ ~(1 << (b)->xfer->sc_link->lun)) /* * Wait for condition, given as an boolean expression. * Print the message on timeout. */ #define WAITFOR(condition,count,message) {\ register u_long cnt = count; char *msg = message;\ while (cnt-- && ! (condition)) continue;\ if (cnt == -1 && msg)\ printf ("nca: %s timeout\n", msg); } static int nca_probe (struct isa_device *dev); static int nca_attach (struct isa_device *dev); static int32_t nca_scsi_cmd (struct scsi_xfer *xs); static u_int32_t nca_adapter_info (int unit); static void nca_timeout (void *scb); static void ncaminphys (struct buf *bp); static void nca_done (adapter_t *z, scb_t *scb); static void nca_start (adapter_t *z); static void nca_information_transfer (adapter_t *z, scb_t *scb); static int nca_poll (adapter_t *z, scb_t *scb); static int nca_init (adapter_t *z); static int nca_reselect (adapter_t *z); static int nca_select (adapter_t *z, scb_t *scb); static int nca_abort (adapter_t *z, scb_t *scb); static void nca_send_abort (adapter_t *z); static u_char nca_msg_input (adapter_t *z); static void nca_tick (void *arg); static int nca_sense (adapter_t *z, scb_t *scb); static void nca_data_output (adapter_t *z, u_char **pdata, u_long *plen); static void nca_data_input (adapter_t *z, u_char **pdata, u_long *plen); static void nca_cmd_output (adapter_t *z, u_char *cmd, int cmdlen); static void nca_53400_dma_xfer (adapter_t *z, int r, u_char **dat, u_long *len); static void nca_pas_dma_xfer (adapter_t *z, int r, u_char **dat, u_long *len); static struct scsi_adapter nca_switch = { nca_scsi_cmd, ncaminphys, 0, 0, nca_adapter_info, "nca", {0}, }; static struct scsi_device nca_dev = { NULL, NULL, NULL, NULL, "nca", 0, {0} }; struct isa_driver ncadriver = { nca_probe, nca_attach, "nca" }; /* * Check if the device can be found at the port given and if so, * detect the type of board. Set it up ready for further work. * Takes the isa_dev structure from autoconf as an argument. * Returns 1 if card recognized, 0 if errors. */ int nca_probe (struct isa_device *dev) { adapter_t *z = &ncadata[dev->id_unit]; int i; /* Init fields used by our routines */ z->parity = (dev->id_flags & FLAG_NOPARITY) ? 0 : MR_ENABLE_PARITY_CHECKING; z->scsi_addr = HOST_SCSI_ADDR; z->scsi_id = 1 << z->scsi_addr; z->irq = dev->id_irq ? ffs (dev->id_irq) - 1 : 0; z->queue = 0; z->disconnected_queue = 0; for (i=0; i<8; i++) z->target[i].busy = 0; /* Link up the free list of scbs */ z->numscb = SCB_TABLE_SIZE; z->free_scb = z->scbs; for (i=1; iscbs[i-1].next = z->scbs + i; z->scbs[SCB_TABLE_SIZE-1].next = 0; /* Try NCR 5380. */ z->type = CTLR_NCR_5380; z->name = "NCR-5380"; z->ODR = dev->id_iobase + C80_ODR; z->CSDR = dev->id_iobase + C80_CSDR; z->ICR = dev->id_iobase + C80_ICR; z->MR = dev->id_iobase + C80_MR; z->TCR = dev->id_iobase + C80_TCR; z->SER = dev->id_iobase + C80_SER; z->CSBR = dev->id_iobase + C80_CSBR; z->BSR = dev->id_iobase + C80_BSR; z->SDSR = dev->id_iobase + C80_SDSR; z->SDIR = dev->id_iobase + C80_SDIR; z->RPIR = dev->id_iobase + C80_RPIR; z->CSR = 0; z->CCR = 0; z->HBR = 0; z->PDATA = 0; z->PSTAT = 0; if (nca_init (z) == 0) return (8); /* Try NCR 53C400. */ z->type = CTLR_NCR_53C400; z->name = "NCR-53C400"; z->ODR = dev->id_iobase + C400_5380_REG_OFFSET + C80_ODR; z->CSDR = dev->id_iobase + C400_5380_REG_OFFSET + C80_CSDR; z->ICR = dev->id_iobase + C400_5380_REG_OFFSET + C80_ICR; z->MR = dev->id_iobase + C400_5380_REG_OFFSET + C80_MR; z->TCR = dev->id_iobase + C400_5380_REG_OFFSET + C80_TCR; z->SER = dev->id_iobase + C400_5380_REG_OFFSET + C80_SER; z->CSBR = dev->id_iobase + C400_5380_REG_OFFSET + C80_CSBR; z->BSR = dev->id_iobase + C400_5380_REG_OFFSET + C80_BSR; z->SDSR = dev->id_iobase + C400_5380_REG_OFFSET + C80_SDSR; z->SDIR = dev->id_iobase + C400_5380_REG_OFFSET + C80_SDIR; z->RPIR = dev->id_iobase + C400_5380_REG_OFFSET + C80_RPIR; z->CSR = dev->id_iobase + C400_CSR; z->CCR = dev->id_iobase + C400_CCR; z->HBR = dev->id_iobase + C400_HBR; z->PDATA = 0; z->PSTAT = 0; if (nca_init (z) == 0) return (16); /* Try ProAudioSpectrum-16. */ z->type = CTLR_PAS_16; z->name = "ProAudioSpectrum"; /* changed later */ z->ODR = dev->id_iobase ^ PAS16_REG (C80_ODR); z->CSDR = dev->id_iobase ^ PAS16_REG (C80_CSDR); z->ICR = dev->id_iobase ^ PAS16_REG (C80_ICR); z->MR = dev->id_iobase ^ PAS16_REG (C80_MR); z->TCR = dev->id_iobase ^ PAS16_REG (C80_TCR); z->SER = dev->id_iobase ^ PAS16_REG (C80_SER); z->CSBR = dev->id_iobase ^ PAS16_REG (C80_CSBR); z->BSR = dev->id_iobase ^ PAS16_REG (C80_BSR); z->SDSR = dev->id_iobase ^ PAS16_REG (C80_SDSR); z->SDIR = dev->id_iobase ^ PAS16_REG (C80_SDIR); z->RPIR = dev->id_iobase ^ PAS16_REG (C80_RPIR); z->CSR = 0; z->CCR = 0; z->HBR = 0; z->PDATA = dev->id_iobase ^ PAS16_REG (PAS16_DATA); z->PSTAT = dev->id_iobase ^ PAS16_REG (PAS16_STAT); if (nca_init (z) == 0) return (4); bzero (z, sizeof (*z)); return (0); } /* * Probe the adapter, and if found, reset the board and the scsi bus. * Return 0 if the adapter found. */ int nca_init (adapter_t *z) { int i, c; if (z->type == CTLR_NCR_53C400) { if (inb (z->CSR) == 0xFF) return (100); /* Reset 53C400. */ outb (z->CSR, CSR_5380_ENABLE); /* Enable interrupts. */ outb (z->CSR, z->irq ? CSR_5380_INTR : 0); } if (z->type == CTLR_PAS_16) { u_short base = z->PDATA & 0x3FF; outb (0x9a01, 0xbc + (z-ncadata)); /* unit number */ outb (0x9a01, base >> 2); if (inb (base^0x803) == 0xFF) return (200); if (inb (z->CSDR) == 0xFF && inb (z->CSDR^0x2000) == 0xFF && inb (z->CSDR) == 0xFF && inb (z->CSDR^0x2000) == 0xFF && inb (z->CSDR) == 0xFF && inb (z->CSDR^0x2000) == 0xFF && inb (z->CSDR) == 0xFF && inb (z->CSDR^0x2000) == 0xFF) return (201); i = inb (base^0x803); outb (base^0x803, i ^ 0xE0); c = inb (base^0x803); outb (base^0x803, 1); if (i != c) return (202); /* Various magic. */ outb (base^0x4000, 0x30); /* Timeout counter */ outb (base^0x4001, 0x01); /* Reset TC */ outb (base^0xbc00, 0x01); /* 1 Wait state */ outb (base^0x8003, 0x4d); /* sysconfig_4 */ i = pas16_irq_magic[z->irq]; if (!i) { z->irq = 0; } else { outb (base^0xf002, i << 4); outb (base^0x8003, 0x6d); /* sysconfig_4 */ } switch (inb (base^0xEC03) & 0xF) { case 6: z->name = "ProAudioSpectrum-Plus"; break; case 12: z->name = "ProAudioSpectrum-16D"; break; case 14: z->name = "ProAudioSpectrum-CDPC"; break; case 15: z->name = "ProAudioSpectrum-16"; break; default: return (203); } } /* Read RPI port, resetting parity/interrupt state. */ inb (z->RPIR); /* Test BSR: parity error, interrupt request and busy loss state * should be cleared. */ if (inb (z->BSR) & (BSR_PARITY_ERROR | BSR_INTERRUPT_REQUEST_ACTIVE | BSR_BUSY_ERROR)) { PRINT (("nca: invalid bsr[0x%x]=%b\n", z->BSR, inb (z->BSR), BSR_BITS)); return (1); } /* Reset the SCSI bus. */ outb (z->ICR, ICR_ASSERT_RST); outb (z->ODR, 0); /* Hold reset for at least 25 microseconds. */ DELAY (25); /* Check that status cleared. */ if (inb (z->CSBR) != CSBR_RST) { PRINT (("nca: invalid csbr[0x%x]=%b\n", z->CSBR, inb (z->CSBR), CSBR_BITS)); outb (z->ICR, 0); return (2); } /* Clear reset. */ outb (z->ICR, 0); /* Wait a Bus Clear Delay (800 ns + bus free delay 800 ns). */ DELAY (2); /* Enable data drivers. */ outb (z->ICR, ICR_ASSERT_DATA_BUS); /* Check that data register is writable. */ for (i=0; i<256; ++i) { outb (z->ODR, i); DELAY (1); if (inb (z->CSDR) != i) { PRINT (("nca: ODR[0x%x] not writable: 0x%x should be 0x%x\n", z->ODR, inb (z->CSDR), i)); outb (z->ICR, 0); return (3); } } /* Disable data drivers. */ outb (z->ICR, 0); /* Check that data register is NOT writable. */ c = inb (z->CSDR); for (i=0; i<256; ++i) { outb (z->ODR, i); DELAY (1); if (inb (z->CSDR) != c) { PRINT (("nca: ODR[0x%x] writable: 0x%x should be 0x%x\n", z->ODR, inb (z->CSDR), c)); return (4); } } /* Initialize the controller. */ outb (z->MR, z->parity); outb (z->TCR, 0); outb (z->SER, z->scsi_id); return (0); } /* * Attach all sub-devices we can find. */ int nca_attach (struct isa_device *dev) { int unit = dev->id_unit; adapter_t *z = &ncadata[unit]; struct scsibus_data *scbus; printf ("nca%d: type %s%s\n", unit, z->name, (dev->id_flags & FLAG_NOPARITY) ? ", no parity" : ""); /* fill in the prototype scsi_link */ z->sc_link.adapter_unit = unit; z->sc_link.adapter_targ = z->scsi_addr; z->sc_link.adapter_softc = z; z->sc_link.adapter = &nca_switch; z->sc_link.device = &nca_dev; /* * Prepare the scsibus_data area for the upperlevel * scsi code. */ scbus = scsi_alloc_bus(); if(!scbus) return 0; scbus->adapter_link = &z->sc_link; /* ask the adapter what subunits are present */ scsi_attachdevs (scbus); return (1); } /* * Return some information to the caller about * the adapter and its capabilities. */ u_int32_t nca_adapter_info (int unit) { return (1); } void ncaminphys (struct buf *bp) { } /* * Catch an interrupt from the adaptor. */ void ncaintr (int unit) { adapter_t *z = &ncadata[unit]; PRINT (("nca%d: interrupt bsr=%b csbr=%b\n", unit, inb (z->BSR), BSR_BITS, inb (z->CSBR), CSBR_BITS)); nca_start (z); /* Reset interrupt state. */ inb (z->RPIR); } /* * This routine is used in the case when we have no IRQ line (z->irq == 0). * It is called every timer tick and polls for reconnect from target. */ void nca_tick (void *arg) { adapter_t *z = arg; int x = splbio (); z->timeout_active = 0; nca_start (z); /* Reset interrupt state. */ inb (z->RPIR); if (z->disconnected_queue && ! z->timeout_active) { timeout (nca_tick, z, 1); z->timeout_active = 1; } splx (x); } /* * Start a scsi operation given the command and the data address. * Also needs the unit, target and lu. Get a free scb and set it up. * Call send_scb. Either start timer or wait until done. */ int32_t nca_scsi_cmd (struct scsi_xfer *xs) { int unit = xs->sc_link->adapter_unit, flags = xs->flags, x = 0; adapter_t *z = (adapter_t *)xs->sc_link->adapter_softc; scb_t *scb; /* PRINT (("nca%d/%d/%d command 0x%x\n", unit, xs->sc_link->target, xs->sc_link->lun, xs->cmd->opcode)); */ if (xs->bp) flags |= SCSI_NOSLEEP; if (flags & ITSDONE) { printf ("nca%d: already done?", unit); xs->flags &= ~ITSDONE; } if (! (flags & INUSE)) { printf ("nca%d: not in use?", unit); xs->flags |= INUSE; } if (flags & SCSI_RESET) printf ("nca%d: SCSI_RESET not implemented\n", unit); if (! (flags & SCSI_NOMASK)) x = splbio (); /* Get a free scb. * If we can and have to, sleep waiting for one to come free. */ while (! (scb = z->free_scb)) { if (flags & SCSI_NOSLEEP) { xs->error = XS_DRIVER_STUFFUP; if (! (flags & SCSI_NOMASK)) splx (x); return (TRY_AGAIN_LATER); } tsleep ((caddr_t)&z->free_scb, PRIBIO, "ncascb", 0); } /* Get scb from free list. */ z->free_scb = scb->next; scb->next = 0; scb->flags = SCB_ACTIVE; /* Put all the arguments for the xfer in the scb */ scb->xfer = xs; scb->datalen = xs->datalen; scb->data = xs->data; /* Setup the scb to contain necessary values. * The interesting values can be read from the xs that is saved. * I therefore think that the structure can be kept very small. * The driver doesn't use DMA so the scatter/gather is not needed? */ if (! z->queue) { scb->next = z->queue; z->queue = scb; } else { scb_t *q; for (q=z->queue; q->next; q=q->next) continue; q->next = scb; scb->next = 0; /* placed at the end of the queue */ } /* Try to send this command to the board. */ nca_start (z); /* Usually return SUCCESSFULLY QUEUED. */ if (! (flags & SCSI_NOMASK)) { splx (x); if (xs->flags & ITSDONE) /* Timeout timer not started, already finished. * Tried to return COMPLETE but the machine hanged * with this. */ return (SUCCESSFULLY_QUEUED); timeout (nca_timeout, (caddr_t) scb, (xs->timeout * hz) / 1000); scb->flags |= SCB_TIMECHK; PRINT (("nca%d/%d/%d command queued\n", unit, xs->sc_link->target, xs->sc_link->lun)); return (SUCCESSFULLY_QUEUED); } /* If we can't use interrupts, poll on completion. */ if (! nca_poll (z, scb)) { /* We timed out, so call the timeout handler manually, * accounting for the fact that the clock is not running yet * by taking out the clock queue entry it makes. */ nca_timeout ((void*) scb); /* Because we are polling, take out the timeout entry * nca_timeout made. */ untimeout (nca_timeout, (void*) scb); if (! nca_poll (z, scb)) /* We timed out again... This is bad. Notice that * this time there is no clock queue entry to remove. */ nca_timeout ((void*) scb); } /* PRINT (("nca%d/%d/%d command %s\n", unit, xs->sc_link->target, xs->sc_link->lun, xs->error ? "failed" : "done")); */ return (xs->error ? HAD_ERROR : COMPLETE); } /* * Coroutine that runs as long as more work can be done. * Both scsi_cmd() and intr() will try to start it in * case it is not running. * Always called with interrupts disabled. */ void nca_start (adapter_t *z) { scb_t *q, *prev; again: /* First check that if any device has tried * a reconnect while we have done other things * with interrupts disabled. */ if (nca_reselect (z)) goto again; /* Search through the queue for a command * destined for a target that's not busy. */ for (q=z->queue, prev=0; q; prev=q, q=q->next) { /* Attempt to establish an I_T_L nexus here. */ if (IS_BUSY (z, q) || ! nca_select (z, q)) continue; /* Remove the command from the issue queue. */ if (prev) prev->next = q->next; else z->queue = q->next; q->next = 0; /* We are connected. Do the task. */ nca_information_transfer (z, q); goto again; } } void nca_timeout (void *arg) { scb_t *scb = (scb_t*) arg; int unit = scb->xfer->sc_link->adapter_unit; adapter_t *z = (adapter_t *)scb->xfer->sc_link->adapter_softc; int x = splbio (); if (! (scb->xfer->flags & SCSI_NOMASK)) printf ("nca%d/%d/%d (%s%d) timed out\n", unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, scb->xfer->sc_link->device->name, scb->xfer->sc_link->dev_unit); /* If it has been through before, then a previous abort has failed, * don't try abort again. */ if (! (scb->flags & SCB_ABORTED)) { nca_abort (z, scb); /* 2 seconds for the abort */ timeout (nca_timeout, (caddr_t)scb, 2*hz); scb->flags |= (SCB_ABORTED | SCB_TIMECHK); } else { /* abort timed out */ scb->flags |= SCB_ABORTED; scb->xfer->retries = 0; nca_done (z, scb); } splx (x); } static inline void nca_sendbyte (adapter_t *z, u_char data) { outb (z->ODR, data); outb (z->ICR, ICR_ASSERT_DATA_BUS | ICR_ASSERT_ACK); WAITFOR (! (inb (z->CSBR) & CSBR_REQ), 10000, "sendbyte"); outb (z->ICR, ICR_ASSERT_DATA_BUS); } static inline u_char nca_recvbyte (adapter_t *z) { u_char data; data = inb (z->CSDR); outb (z->ICR, ICR_ASSERT_ACK); WAITFOR (! (inb (z->CSBR) & CSBR_REQ), 10000, "recvbyte"); outb (z->ICR, 0); return (data); } /* * Establish I_T_L or I_T_L_Q nexus for new or existing command * including ARBITRATION, SELECTION, and initial message out * for IDENTIFY and queue messages. * Return 1 if selection succeded. */ int nca_select (adapter_t *z, scb_t *scb) { /* Set the phase bits to 0, otherwise the NCR5380 won't drive the * data bus during SELECTION. */ outb (z->TCR, 0); /* Start arbitration. */ outb (z->ODR, z->scsi_id); outb (z->MR, MR_ARBITRATE); /* Wait for arbitration logic to complete (20 usec) */ WAITFOR (inb (z->ICR) & ICR_ARBITRATION_IN_PROGRESS, 200, 0); if (! (inb (z->ICR) & ICR_ARBITRATION_IN_PROGRESS)) { PRINT (("nca%d/%d/%d no arbitration progress, bsr=%b csbr=%b\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, inb (z->BSR), BSR_BITS, inb (z->CSBR), CSBR_BITS)); outb (z->MR, z->parity); return (0); } DELAY (3); /* Check for lost arbitration. */ if ((inb (z->ICR) & ICR_LOST_ARBITRATION) || (inb (z->CSDR) >> 1 >> z->scsi_addr) || (inb (z->ICR) & ICR_LOST_ARBITRATION)) { PRINT (("nca%d/%d/%d arbitration lost\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); outb (z->MR, z->parity); return (0); } outb (z->ICR, ICR_ASSERT_SEL); if (inb (z->ICR) & ICR_LOST_ARBITRATION) { PRINT (("nca%d/%d/%d arbitration lost after SEL\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); outb (z->ICR, 0); outb (z->MR, z->parity); return (0); } DELAY (2); /* Start selection, asserting the host and target ID's on the bus. */ outb (z->SER, 0); outb (z->ODR, z->scsi_id | (1 << scb->xfer->sc_link->target)); outb (z->ICR, ICR_ASSERT_DATA_BUS | ICR_ASSERT_BSY | ICR_ASSERT_SEL); /* Finish arbitration, drop BSY. */ outb (z->MR, 0); outb (z->ICR, ICR_ASSERT_DATA_BUS | ICR_ASSERT_SEL | ICR_ASSERT_ATN); DELAY (1); /* The SCSI specification calls for a 250 ms timeout for the actual * selection. */ WAITFOR (inb (z->CSBR) & CSBR_BSY, 100000, 0); if (! (inb (z->CSBR) & CSBR_BSY)) { /* The target does not respond. Not an error, though. */ PRINT (("nca%d/%d/%d target does not respond\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); outb (z->ICR, 0); outb (z->SER, z->scsi_id); outb (z->MR, z->parity); scb->flags |= SCB_TIMEOUT; return (0); } /* Clear SEL and SCSI id. * Wait for start of REQ/ACK handshake. */ outb (z->ICR, ICR_ASSERT_DATA_BUS | ICR_ASSERT_ATN); WAITFOR (inb (z->CSBR) & CSBR_REQ, 100000, 0); if (! (inb (z->CSBR) & CSBR_REQ)) { PRINT (("nca%d/%d/%d timeout waiting for REQ\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); outb (z->ICR, 0); outb (z->SER, z->scsi_id); outb (z->MR, z->parity); scb->flags |= SCB_ERROR; return (0); } /* Check for phase mismatch. */ if ((inb (z->CSBR) & PHASE_MASK) != PHASE_MSGOUT) { /* This should not be taken as an error, but more like * an unsupported feature! * Should set a flag indicating that the target don't support * messages, and continue without failure. * (THIS IS NOT AN ERROR!) */ PRINT (("nca%d/%d/%d waiting for MSGOUT: invalid phase %s\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, PHASE_NAME (inb (z->CSBR) & PHASE_MASK))); outb (z->ICR, 0); outb (z->SER, z->scsi_id); outb (z->MR, z->parity); scb->flags |= SCB_ERROR; return (0); } /* Allow disconnects. */ outb (z->TCR, PHASE_TO_TCR (PHASE_MSGOUT)); outb (z->ICR, ICR_ASSERT_DATA_BUS); nca_sendbyte (z, MSG_IDENTIFY (scb->xfer->sc_link->lun)); outb (z->ICR, 0); outb (z->SER, z->scsi_id); outb (z->MR, z->parity); SET_BUSY (z, scb); return (1); } int nca_reselect (adapter_t *z) { scb_t *q = 0, *prev = 0; u_char msg, target_mask, lun; again: /* Wait for a device to win the reselection phase. */ /* Signals this by asserting the I/O signal. */ if ((inb (z->CSBR) & (CSBR_SEL | CSBR_IO | CSBR_BSY)) != (CSBR_SEL | CSBR_IO)) return (0); /* The data bus contains original initiator id ORed with target id. */ /* See that we really are the initiator. */ target_mask = inb (z->CSDR); if (! (target_mask & z->scsi_id)) { PRINT (("nca%d reselect not for me: mask=0x%x, csbr=%b\n", z->sc_link.adapter_unit, target_mask, inb (z->CSBR), CSBR_BITS)); goto again; } /* Find target who won. */ /* Host responds by asserting the BSY signal. */ /* Target should respond by deasserting the SEL signal. */ target_mask &= ~z->scsi_id; outb (z->ICR, ICR_ASSERT_BSY); WAITFOR (! (inb (z->CSBR) & CSBR_SEL), 10000, "SEL deassert"); /* Remove the busy status. */ /* Target should set the MSGIN phase. */ outb (z->ICR, 0); WAITFOR (inb (z->CSBR) & CSBR_REQ, 10000, "MSGIN"); /* Hope we get an IDENTIFY message. */ msg = nca_msg_input (z); if (MSG_ISIDENT (msg)) { /* Find the command corresponding to the I_T_L or I_T_L_Q * nexus we just restablished, and remove it from * the disconnected queue. */ lun = (msg & 7); for (q=z->disconnected_queue; q; prev=q, q=q->next) { if (target_mask != (1 << q->xfer->sc_link->target)) continue; if (lun != q->xfer->sc_link->lun) continue; if (prev) prev->next = q->next; else z->disconnected_queue = q->next; q->next = 0; PRINT (("nca%d/%d/%d reselect done\n", z->sc_link.adapter_unit, ffs (target_mask) - 1, lun)); nca_information_transfer (z, q); WAITFOR (! (inb (z->CSBR) & CSBR_BSY), 100000, "reselect !busy"); return (1); } } else printf ("nca%d reselect: expecting IDENTIFY, got 0x%x\n", z->sc_link.adapter_unit, msg); /* Since we have an established nexus that we can't * do anything with, we must abort it. */ nca_send_abort (z); PRINT (("nca%d reselect aborted\n", z->sc_link.adapter_unit)); WAITFOR (! (inb (z->CSBR) & CSBR_BSY), 100000, "reselect abort !busy"); goto again; } /* * Send an abort to the target. * Return 1 success, 0 on failure. * Called on splbio level. */ int nca_abort (adapter_t *z, scb_t *scb) { scb_t *q, **prev; /* If the command hasn't been issued yet, we simply remove it * from the issue queue. */ prev = &z->queue; for (q=z->queue; q; q=q->next) { if (scb == q) { (*prev) = q->next; q->next = 0; return (1); } prev = &q->next; } /* If the command is currently disconnected from the bus, * we reconnect the I_T_L or I_T_L_Q nexus associated with it, * go into message out, and send an abort message. */ for (q=z->disconnected_queue; q; q=q->next) { if (scb != q) continue; if (! nca_select (z, scb)) return (0); nca_send_abort (z); prev = &z->disconnected_queue; for (q=z->disconnected_queue; q; q=q->next) { if (scb == q) { *prev = q->next; q->next = 0; /* Set some type of error result * for the operation. */ return (1); } prev = &q->next; } } /* Command not found in any queue. */ return (0); } /* * The task accomplished, mark the i/o control block as done. * Always called with interrupts disabled. */ void nca_done (adapter_t *z, scb_t *scb) { struct scsi_xfer *xs = scb->xfer; if (scb->flags & SCB_TIMECHK) untimeout (nca_timeout, (caddr_t) scb); /* How much of the buffer was not touched. */ xs->resid = scb->datalen; if (scb->flags != SCB_ACTIVE && ! (xs->flags & SCSI_ERR_OK)) if (scb->flags & (SCB_TIMEOUT | SCB_ABORTED)) xs->error = XS_TIMEOUT; else if (scb->flags & SCB_ERROR) xs->error = XS_DRIVER_STUFFUP; else if (scb->flags & SCB_TBUSY) xs->error = XS_BUSY; else if (scb->flags & SCB_SENSE) xs->error = XS_SENSE; xs->flags |= ITSDONE; /* Free the control block. */ scb->next = z->free_scb; z->free_scb = scb; scb->flags = SCB_FREE; /* If there were none, wake anybody waiting for one to come free, * starting with queued entries. */ if (! scb->next) wakeup ((caddr_t) &z->free_scb); scsi_done (xs); } /* * Wait for completion of command in polled mode. * Always called with interrupts masked out. */ int nca_poll (adapter_t *z, scb_t *scb) { int count; for (count=0; count<30; ++count) { DELAY (1000); /* delay for a while */ nca_start (z); /* retry operation */ if (scb->xfer->flags & ITSDONE) return (1); /* all is done */ if (scb->flags & SCB_TIMEOUT) return (0); /* no target present */ } return (0); } /* * Perform NCR-53C400 pseudo-dma data transfer. */ void nca_53400_dma_xfer (adapter_t *z, int read, u_char **pdata, u_long *plen) { /* Set dma direction. */ outb (z->CSR, read ? CSR_TRANSFER_DIRECTION : 0); /* Enable dma mode. */ outb (z->MR, MR_DMA_MODE | (read ? z->parity : 0)); /* Start dma transfer. */ outb (read ? z->SDIR : z->SDSR, 0); /* Set up clock counter. */ outb (z->CCR, *plen/128); for (; *plen>=128; *plen-=128, *pdata+=128) { /* Wait for 53C400 host buffer ready. */ WAITFOR (! (inb (z->CSR) & CSR_HOST_BUF_NOT_READY), 100000, 0); if (inb (z->CSR) & CSR_HOST_BUF_NOT_READY) break; /* Transfer 128 bytes of data. */ if (read) insw (z->HBR, *pdata, 64); else outsw (z->HBR, *pdata, 64); } /* Wait for 5380 registers ready. */ WAITFOR (inb (z->CSR) & CSR_5380_ENABLE, 10000, 0); if (! (inb (z->CSR) & CSR_5380_ENABLE)) { /* Reset 53C400. */ PRINT (("nca%d: reset: pseudo-dma incomplete, csr=%b\n", z->sc_link.adapter_unit, inb (z->CSR), CSR_BITS)); outb (z->CSR, CSR_5380_ENABLE); outb (z->CSR, 0); } /* Wait for FIFO flush on write. */ if (! read) WAITFOR (inb (z->TCR) & TCR_LAST_BYTE_SENT, 10000, "last byte"); /* Clear dma mode. */ outb (z->MR, z->parity); /* Re-enable interrupts. */ outb (z->CSR, z->irq ? CSR_5380_INTR : 0); } /* * Perform PAS-16 pseudo-dma data transfer. */ void nca_pas_dma_xfer (adapter_t *z, int read, u_char **pdata, u_long *plen) { /* Enable dma mode. */ outb (z->MR, MR_DMA_MODE | (read ? z->parity : 0)); /* Start dma transfer. */ outb (read ? z->SDIR : z->SDSR, 0); for (; *plen>=512; *plen-=512, *pdata+=512) { /* Wait for pseudo-DMA request. */ WAITFOR (inb (z->PSTAT) & PAS16_STAT_DREQ, 10000, "pseudo-dma"); if (! (inb (z->PSTAT) & PAS16_STAT_DREQ)) break; /* Transfer 512 bytes of data. */ if (read) insb (z->PDATA, *pdata, 512); else outsb (z->PDATA, *pdata, 512); } /* Clear dma mode. */ outb (z->MR, z->parity); } /* * Send data to the target. */ void nca_data_output (adapter_t *z, u_char **pdata, u_long *plen) { u_char *data = *pdata; u_long len = *plen; outb (z->ICR, ICR_ASSERT_DATA_BUS); if (z->type == CTLR_NCR_53C400 && len%128 == 0) /* Use NCR-53C400 pseudo-dma for data transfer. */ nca_53400_dma_xfer (z, 0, &data, &len); else if (z->type == CTLR_PAS_16 && len%512 == 0) /* Use PAS-16 pseudo-dma for data transfer. */ nca_pas_dma_xfer (z, 0, &data, &len); else for (;;) { /* Check SCSI bus phase. */ u_char s = inb (z->CSBR) ^ (CSBR_BSY | PHASE_DATAOUT); if (s & (CSBR_BSY | PHASE_MASK)) break; /* Wait for REQ. */ if (! (s & CSBR_REQ)) continue; /* Output data. */ outb (z->ODR, *data++); /* Assert ACK and wait for REQ deassert, * with irqs disabled. */ disable_intr (); outb (z->ICR, ICR_ASSERT_ACK | ICR_ASSERT_DATA_BUS); WAITFOR (! (inb (z->CSBR) & CSBR_REQ), 1000, 0); enable_intr (); /* Deassert ACK. */ outb (z->ICR, ICR_ASSERT_DATA_BUS); --len; } outb (z->ICR, 0); PRINT (("nca (DATAOUT) send %ld bytes\n", *plen - len)); *plen = len; *pdata = data; } /* * Receive data from the target. */ void nca_data_input (adapter_t *z, u_char **pdata, u_long *plen) { u_char *data = *pdata; u_long len = *plen; if (z->type == CTLR_NCR_53C400 && len%128 == 0) /* Use NCR-53C400 pseudo-dma for data transfer. */ nca_53400_dma_xfer (z, 1, &data, &len); else if (z->type == CTLR_PAS_16 && len%512 == 0) /* Use PAS-16 pseudo-dma for data transfer. */ nca_pas_dma_xfer (z, 1, &data, &len); else for (;;) { /* Check SCSI bus phase. */ u_char s = inb (z->CSBR) ^ (CSBR_BSY | PHASE_DATAIN); if (s & (CSBR_BSY | PHASE_MASK)) break; /* Wait for REQ. */ if (! (s & CSBR_REQ)) continue; /* Input data. */ *data++ = inb (z->CSDR); /* Assert ACK and wait for REQ deassert, * with irqs disabled. */ disable_intr (); outb (z->ICR, ICR_ASSERT_ACK); WAITFOR (! (inb (z->CSBR) & CSBR_REQ), 1000, 0); enable_intr (); /* Deassert ACK. */ outb (z->ICR, 0); --len; } PRINT (("nca (DATAIN) got %ld bytes\n", *plen - len)); *plen = len; *pdata = data; } /* * Send the command to the target. */ void nca_cmd_output (adapter_t *z, u_char *cmd, int cmdlen) { PRINT (("nca%d send command (%d bytes) ", z->sc_link.adapter_unit, cmdlen)); outb (z->ICR, ICR_ASSERT_DATA_BUS); while (cmdlen) { /* Check for target disconnect. */ u_char sts = inb (z->CSBR); if (! (sts & CSBR_BSY)) break; /* Check for phase mismatch. */ if ((sts & PHASE_MASK) != PHASE_CMDOUT) { printf ("nca: sending command: invalid phase %s\n", PHASE_NAME (sts & PHASE_MASK)); break; } /* Wait for REQ. */ if (! (sts & CSBR_REQ)) continue; PRINT (("-%x", *cmd)); nca_sendbyte (z, *cmd++); --cmdlen; } outb (z->ICR, 0); PRINT (("\n")); } /* * Send the message to the target. */ void nca_send_abort (adapter_t *z) { u_char sts; outb (z->ICR, ICR_ASSERT_ATN); /* Wait for REQ, after which the phase bits will be valid. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 1000000, "abort message"); sts = inb (z->CSBR); if (! (sts & CSBR_REQ)) goto ret; /* Check for phase mismatch. */ if ((sts & PHASE_MASK) != PHASE_MSGOUT) { printf ("nca: sending MSG_ABORT: invalid phase %s\n", PHASE_NAME (sts & PHASE_MASK)); goto ret; } outb (z->ICR, ICR_ASSERT_DATA_BUS); outb (z->TCR, PHASE_TO_TCR (PHASE_MSGOUT)); nca_sendbyte (z, MSG_ABORT); PRINT (("nca%d send MSG_ABORT\n", z->sc_link.adapter_unit)); ret: outb (z->ICR, 0); } /* * Get the message from the target. * Return the length of the received message. */ u_char nca_msg_input (adapter_t *z) { u_char sts, msg; /* Wait for REQ, after which the phase bits will be valid. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 1000000, "message input"); sts = inb (z->CSBR); if (! (sts & CSBR_REQ)) return (MSG_ABORT); /* Check for phase mismatch. * Reached if the target decides that it has finished the transfer. */ if ((sts & PHASE_MASK) != PHASE_MSGIN) { printf ("nca: sending message: invalid phase %s\n", PHASE_NAME (sts & PHASE_MASK)); return (MSG_ABORT); } /* Do actual transfer from SCSI bus to memory. */ outb (z->TCR, PHASE_TO_TCR (PHASE_MSGIN)); msg = nca_recvbyte (z); PRINT (("nca%d (MSG_INPUT) got 0x%x\n", z->sc_link.adapter_unit, msg)); return (msg); } /* * Send request-sense op to the target. * Return 1 success, 0 on failure. * Called on splbio level. */ int nca_sense (adapter_t *z, scb_t *scb) { u_char cmd[6], status, msg, *data; u_long len; /* Wait for target to disconnect. */ WAITFOR (! (inb (z->CSBR) & CSBR_BSY), 100000, "sense bus free"); if (inb (z->CSBR) & CSBR_BSY) return (0); /* Select the target again. */ if (! nca_select (z, scb)) return (0); /* Wait for CMDOUT phase. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 100000, "sense CMDOUT"); if (! (inb (z->CSBR) & CSBR_REQ) || (inb (z->CSBR) & PHASE_MASK) != PHASE_CMDOUT) return (0); outb (z->TCR, PHASE_TO_TCR (PHASE_CMDOUT)); /* Send command. */ len = sizeof (scb->xfer->sense); cmd[0] = REQUEST_SENSE; cmd[1] = scb->xfer->sc_link->lun << 5; cmd[2] = 0; cmd[3] = 0; cmd[4] = len; cmd[5] = 0; nca_cmd_output (z, cmd, sizeof (cmd)); /* Wait for DATAIN phase. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 100000, "sense DATAIN"); if (! (inb (z->CSBR) & CSBR_REQ) || (inb (z->CSBR) & PHASE_MASK) != PHASE_DATAIN) return (0); outb (z->TCR, PHASE_TO_TCR (PHASE_DATAIN)); data = (u_char*) &scb->xfer->sense; nca_data_input (z, &data, &len); PRINT (("nca%d sense %x-%x-%x-%x-%x-%x-%x-%x\n", z->sc_link.adapter_unit, scb->xfer->sense.error_code, scb->xfer->sense.ext.extended.segment, scb->xfer->sense.ext.extended.flags, scb->xfer->sense.ext.extended.info[0], scb->xfer->sense.ext.extended.info[1], scb->xfer->sense.ext.extended.info[2], scb->xfer->sense.ext.extended.info[3], scb->xfer->sense.ext.extended.extra_len)); /* Wait for STATIN phase. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 100000, "sense STATIN"); if (! (inb (z->CSBR) & CSBR_REQ) || (inb (z->CSBR) & PHASE_MASK) != PHASE_STATIN) return (0); outb (z->TCR, PHASE_TO_TCR (PHASE_STATIN)); status = nca_recvbyte (z); /* Wait for MSGIN phase. */ WAITFOR (inb (z->CSBR) & CSBR_REQ, 100000, "sense MSGIN"); if (! (inb (z->CSBR) & CSBR_REQ) || (inb (z->CSBR) & PHASE_MASK) != PHASE_MSGIN) return (0); outb (z->TCR, PHASE_TO_TCR (PHASE_MSGIN)); msg = nca_recvbyte (z); if (status != 0 || msg != 0) printf ("nca%d: bad sense status=0x%x, msg=0x%x\n", z->sc_link.adapter_unit, status, msg); return (1); } /* * Do the transfer. We know we are connected. Update the flags, * call nca_done when task accomplished. Dialog controlled by the target. * Always called with interrupts disabled. */ void nca_information_transfer (adapter_t *z, scb_t *scb) { u_char *data = scb->data; /* current data buffer */ u_long datalen = scb->datalen; /* current data transfer size */ register u_char sts; u_char msg; while ((sts = inb (z->CSBR)) & CSBR_BSY) { /* We only have a valid SCSI phase when REQ is asserted. */ if (! (sts & CSBR_REQ)) continue; if (inb (z->BSR) & BSR_PARITY_ERROR) { int target = scb->xfer->sc_link->target; if (++z->target[target].perrcnt <= 8) printf ("nca%d/%d/%d parity error\n", z->sc_link.adapter_unit, target, scb->xfer->sc_link->lun); if (z->target[target].perrcnt == 8) printf ("nca%d/%d/%d too many parity errors, not logging any more\n", z->sc_link.adapter_unit, target, scb->xfer->sc_link->lun); /* Clear parity error. */ inb (z->RPIR); } outb (z->TCR, PHASE_TO_TCR (sts & PHASE_MASK)); switch (sts & PHASE_MASK) { case PHASE_DATAOUT: if (datalen <= 0) { printf ("nca%d/%d/%d data length underflow\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun); /* send zero byte */ outb (z->ICR, ICR_ASSERT_DATA_BUS); nca_sendbyte (z, 0); outb (z->ICR, 0); break; } nca_data_output (z, &data, &datalen); break; case PHASE_DATAIN: if (datalen <= 0) { /* Get extra data. Some devices (e.g. CDROMs) * use fixed-length blocks (e.g. 2k), * even if we need less. */ PRINT (("@")); nca_recvbyte (z); break; } nca_data_input (z, &data, &datalen); break; case PHASE_CMDOUT: nca_cmd_output (z, (u_char*) scb->xfer->cmd, scb->xfer->cmdlen); break; case PHASE_STATIN: scb->xfer->status = nca_recvbyte (z); PRINT (("nca%d/%d/%d (STATIN) got 0x%x\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, (u_char) scb->xfer->status)); break; case PHASE_MSGOUT: /* Send no-op message. */ outb (z->ICR, ICR_ASSERT_DATA_BUS); nca_sendbyte (z, MSG_NOP); outb (z->ICR, 0); PRINT (("nca%d/%d/%d (MSGOUT) send NOP\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); break; case PHASE_MSGIN: /* Don't handle multi-byte messages here, because they * should not be present here. */ msg = nca_recvbyte (z); PRINT (("nca%d/%d/%d (MSGIN) got 0x%x\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, msg)); switch (msg) { case MSG_COMMAND_COMPLETE: scb->data = data; scb->datalen = datalen; /* In the case of check-condition status, * perform the request-sense op. */ switch (scb->xfer->status & 0x1e) { case SCSI_CHECK: if (nca_sense (z, scb)) scb->flags = SCB_SENSE; break; case SCSI_BUSY: scb->flags = SCB_TBUSY; break; } goto done; case MSG_ABORT: printf ("nca: command aborted by target\n"); scb->flags = SCB_ABORTED; goto done; case MSG_MESSAGE_REJECT: printf ("nca: message rejected\n"); scb->flags = SCB_ABORTED; goto done; case MSG_DISCONNECT: scb->next = z->disconnected_queue; z->disconnected_queue = scb; if (! z->irq && ! z->timeout_active) { timeout (nca_tick, z, 1); z->timeout_active = 1; } PRINT (("nca%d/%d/%d disconnected\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun)); goto ret; case MSG_SAVE_POINTERS: scb->data = data; scb->datalen = datalen; break; case MSG_RESTORE_POINTERS: data = scb->data; datalen = scb->datalen; break; default: printf ("nca%d/%d/%d unknown message: 0x%x\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun, msg); break; } break; default: printf ("nca: unknown phase: %b\n", sts, CSBR_BITS); break; } } printf ("nca%d/%d/%d unexpected target disconnect\n", z->sc_link.adapter_unit, scb->xfer->sc_link->target, scb->xfer->sc_link->lun); scb->flags = SCB_ERROR; done: CLEAR_BUSY (z, scb); nca_done (z, scb); ret: outb (z->ICR, 0); outb (z->TCR, 0); outb (z->SER, z->scsi_id); WAITFOR (! (inb (z->CSBR) & CSBR_BSY), 100000, "xfer bus free"); } #endif /* NNCA */