- Try to unbreak what I broke by screwing with the tx queuing again.
I'm waiting for a few more people to test out this code and report back
before I move it into current. Hopefully it will be soon. Basically I
reverted to the old TX queuing strategy.
- Add experimental support for the 3c900B-FL (10mbps ST fiber). The card
should be detected properly and the 10baseFL mode supported, but again
I'm still waiting for word from a tester to see if this actually works.
It shouldn't affect the other cards though; all the differences are in
media selection.
- Set the TX start threshold register to get better performance.
- Increase the size of the RX and TX rings. UDP performance was pretty
bad because the TX ring was too small. Should be substantially better
now (I can saturate the link with either TCP or UDP now).
- Change some of the #defines to reflect proper 3Com ASIC names (boomerang,
cyclone, krakatoa, hurricane).
- Simplify and reorganize interrupt handler; ack all interrupts right
away and then process them. This avoids a potential race condition.
(Noted by Matt Dillon.)
- Reorganize the bridging code to eliminate using a goto to jump into
the middle of an if() {} clause. Sorry, that just made my brain itch.
- Use m_adj() in xl_rxeof().
- Make the payload alignment in xl_newbuf() the default (instead of
just conditionally defined for the alpha) to improve NFS performance
(avoids need for nfs_realign()).
-------------------------------------------------------------------------------
Recent versions of 3.0-current have the bktr driver built in. Older versions
of 3.0 and all versions of 2.2 need to have the driver files installed by hand:
cp ioctl_bt848.h /sys/i386/include/
cp brktree_reg.h brooktree848.c /sys/pci/
In /sys/conf/files add:
pci/brooktree848.c optional bktr device-driver
-------------------------------------------------------------------------------
In all cases you will need to add the driver to your kernel:
In your kernel configuration file:
controller pci0 #if you already have this line don't add it.
device bktr0
There is no need to specify DMA channels nor interrupts for this
driver.
-------------------------------------------------------------------------------
Finally you need to create nodes for the driver:
Create a video device:
mknod /dev/bktr0 c 92 0
Create a tuner device:
mknod /dev/tuner0 c 92 16
-------------------------------------------------------------------------------
The code attempts to auto-probe code to detect card/tuner types.
The detected card is printed in the dmesg as the driver is loaded. If
this fails to detect the proper card you can override it in brooktree848.c:
#define OVERRIDE_CARD <card type>
where <card type> is one of:
CARD_UNKNOWN
CARD_MIRO
CARD_HAUPPAUGE
CARD_STB
CARD_INTEL
-------------------------------------------------------------------------------
This model now separates the "tuner control" items into a minor device:
minor device layout: xxxxxxxx xxxT UUUU
UUUU: the card (ie UNIT) identifier, 0 thru 15
T == 0: video device
T == 1: tuner device
Access your tuner ioctl thru your tuner device handle and anything
which controls the video capture process thru the video device handle.
Certain ioctl()s such as video source are available thru both devices.
-------------------------------------------------------------------------------
If your tuner does not work properly or is not recognized properly
try setting the tuner type via or card type:
sysctl -w hw.bt848.card=<integer> current valid values are 0 to 5 inclusive
sysctl -w hw.bt848.tuner=<integer> where integer is a value from 1 to 10
systcl -w hw.bt848.reverse_mute=<1 | 0> to reverse the mute function in the
driver set variable to 1.
The exact format of the sysctl bt848 variable is:
unit << 8 | value
unit identifies the pci bt848 board to be affected 0 is the first bt848
board, 1 is the second bt848 board.
value denotes the integer value for tuners is a value from 0 to 10 for
reversing the mute function of the tuner the value is 1 or 0.
to find out all the bt848 variables:
sysctl hw.bt848
-------------------------------------------------------------------------------
The bt848 driver consists of:
src/sys/i386/include/ioctl_bt848.h
src/sys/pci/brktree_reg.h
src/sys/pci/brooktree848.c
0a9766ee3a