22a3aee637
PS-POLL support. This implements PS-POLL awareness i nthe * Implement frame "leaking", which allows for a software queue to be scheduled even though it's asleep * Track whether a frame has been leaked or not * Leak out a single non-AMPDU frame when transmitting aggregates * Queue BAR frames if the node is asleep * Direct-dispatch the rest of control and management frames. This allows for things like re-association to occur (which involves sending probe req/resp as well as assoc request/response) when the node is asleep and then tries reassociating. * Limit how many frames can set in the software node queue whilst the node is asleep. net80211 is already buffering frames for us so this is mostly just paranoia. * Add a PS-POLL method which leaks out a frame if there's something in the software queue, else it calls net80211's ps-poll routine. Since the ath PS-POLL routine marks the node as having a single frame to leak, either a software queued frame would leak, OR the next queued frame would leak. The next queued frame could be something from the net80211 power save queue, OR it could be a NULL frame from net80211. TODO: * Don't transmit further BAR frames (eg via a timeout) if the node is currently asleep. Otherwise we may end up exhausting management frames due to the lots of queued BAR frames. I may just undo this bit later on and direct-dispatch BAR frames even if the node is asleep. * It would be nice to burst out a single A-MPDU frame if both ends support this. I may end adding a FreeBSD IE soon to negotiate this power save behaviour. * I should make STAs timeout of power save mode if they've been in power save for more than a handful of seconds. This way cards that get "stuck" in power save mode don't stay there for the "inactivity" timeout in net80211. * Move the queue depth check into the driver layer (ath_start / ath_transmit) rather than doing it in the TX path. * There could be some naughty corner cases with ps-poll leaking. Specifically, if net80211 generates a NULL data frame whilst another transmitter sends a normal data frame out net80211 output / transmit, we need to ensure that the NULL data frame goes out first. This is one of those things that should occur inside the VAP/ic TX lock. Grr, more investigations to do.. Tested: * STA: AR5416, AR9280 * AP: AR5416, AR9280, AR9160
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html