ded9da6832
This patch implements and exports functions described in gpio_if.m file. It also uses new gpiobus_attach_bus function instead of adding gpioc and gpiobus as children. It removes ulgy reading SoC ID and related if..else, so it depends only on data read from FDT. Submitted by: Patryk Duda <pdk@semihalf.com> Reviewed by: manu Obtained from: Semihalf Sponsored by: Stormshield Differential Revision: https://reviews.freebsd.org/D14756
107 lines
2.6 KiB
Plaintext
107 lines
2.6 KiB
Plaintext
$FreeBSD$
|
|
|
|
GPIO configuration.
|
|
===================
|
|
|
|
1. Properties for GPIO Controllers
|
|
|
|
1.1 #gpio-cells
|
|
|
|
Property: #gpio-cells
|
|
|
|
Value type: <u32>
|
|
|
|
Description: The #gpio-cells property defines the number of cells required
|
|
to encode a gpio specifier.
|
|
|
|
|
|
1.2 gpio-controller
|
|
|
|
Property: gpio-controller
|
|
|
|
Value type: <empty>
|
|
|
|
Description: The presence of a gpio-controller property defines a node as a
|
|
GPIO controller node.
|
|
|
|
|
|
1.3 pin-count
|
|
|
|
Property: pin-count
|
|
|
|
Value type: <u32>
|
|
|
|
Description: The pin-count property defines the number of GPIO pins.
|
|
|
|
|
|
1.4 Example
|
|
|
|
GPIO: gpio@10100 {
|
|
#gpio-cells = <3>;
|
|
compatible = "mrvl,gpio";
|
|
reg = <0x10100 0x20>;
|
|
gpio-controller;
|
|
interrupts = <6 7 8 9>;
|
|
interrupt-parent = <&PIC>;
|
|
pin-count = <50>
|
|
};
|
|
|
|
2. Properties for GPIO consumer nodes.
|
|
|
|
2.1 gpios
|
|
|
|
Property: gpios
|
|
|
|
Value type: <prop-encoded-array> encoded as arbitrary number of GPIO
|
|
specifiers.
|
|
|
|
Description: The gpios property of a device node defines the GPIO or GPIOs
|
|
that are used by the device. The value of the gpios property
|
|
consists of an arbitrary number of GPIO specifiers.
|
|
|
|
The first cell of the GPIO specifier is phandle of the node's
|
|
parent GPIO controller and remaining cells are defined by the
|
|
binding describing the GPIO parent, typically include
|
|
information like pin number, direction and various flags.
|
|
|
|
Example:
|
|
gpios = <&GPIO 0 1 /* GPIO[0]: FLAGS */
|
|
&GPIO 1 2>; /* GPIO[1]: FLAGS */
|
|
|
|
|
|
3. GPIO controller specifier
|
|
|
|
<phandle pin dir flags>
|
|
|
|
|
|
pin: 0-MAX GPIO pin number.
|
|
|
|
flags:
|
|
Available flags are listed in sys/conf.h. Following combination
|
|
can be supported by the controller. For details please refer
|
|
to controller's GPIO reference manual.
|
|
|
|
GPIO_PIN_INPUT 0x0001 Input direction
|
|
GPIO_PIN_OUTPUT 0x0002 Output direction
|
|
GPIO_PIN_OPENDRAIN 0x0004 Open-drain output
|
|
GPIO_PIN_OPENSOURCE 0x0008 Open-source output
|
|
GPIO_PIN_PUSHPULL 0x0010 Push-pull output
|
|
GPIO_PIN_TRISTATE 0x0020 Output disabled
|
|
GPIO_PIN_PULLUP 0x0040 Internal pull-up enabled
|
|
GPIO_PIN_PULLDOWN 0x0080 Internal pull-down enabled
|
|
GPIO_PIN_INVIN 0x0100 Invert input
|
|
GPIO_PIN_INVOUT 0x0200 Invert output
|
|
GPIO_PIN_PULSATE 0x0400 Pulsate in hardware
|
|
GPIO_PIN_IRQ_POL_EDG 0x0800 IRQ active single edge
|
|
GPIO_PIN_IRQ_POL_DBL 0x1000 IRQ active double edge
|
|
GPIO_PIN_IRQ_POL_LVL 0x2000 IRQ active level
|
|
GPIO_PIN_IRQ_DEBOUNCE 0x4000 Debounce on IRQ pin
|
|
|
|
Example:
|
|
gpios = <&GPIO 0 0x00000001 /* GPIO[0]: IN */
|
|
&GPIO 1 0x00000002 /* GPIO[1]: OUT */
|
|
&GPIO 2 0x00000801 /* GPIO[2]: IN, IRQ (edge) */
|
|
&GPIO 3 0x00004001 /* GPIO[3]: IN, IRQ (level) */
|
|
...
|
|
&GPIO 10 0x00000401>; /* GPIO[10]: OUT, blink */
|