freebsd-nq/sys/dev/slice/slice.4

yes I know this is not in mandoc format..

The slices are stackable..
With alternating layers of handler(driver)/slice/handler/slice/handler/slice
The "Slice" is implemented as a common structure shared between three
pieces of code. Each slice in the stack can be thought of in OO terms as
an instance of the 'slice' object. Methods include all the 'device' node
methods exported via the cdevsw[], bdevsw[] and devfs interfaces. Thus
whenever a handler exports a slice object, a unique node is made available
to the users via the device system, to access that slice, as if it were a
disk in it's own right. Since the interface is implemented by the same
code no matter where in the stack it occurs, all partitions and devices
which are exported by the slice code, exhibit almost identical behavior.
Theoretically, it should be possible to treat a partition of a device, as
if it were a separate device, as it should exhibit the same behavior as
the device itself (except for size).

The diagram below exhibits the form of one layer of the stack. Each handler
can decide how many slices to export on the upper side, and 
how many slices to connect to on the lower side. If A slice can not be
further subdivided, there may not be an upper handler.

 [upper handler] (optional)
       ^
       |
       |
       v                                        |------ raw (char) device
[common slice information]<---------->[slice device]
       ^                                        |------ block device
       |
       |
       v
 [lower handler]  (may be a device driver)

Each of these 3 items share some knowledge of the internal structure and
contents of the slice structure. They also know each other's published 
interfaces. This may change as the design settles down and it becomes more
obvious which parts can be hidden.

The slices are created bottom up.
When the driver decides that there is media that should be made available,
it creates a 'slice' object to represent it. This slice object comes with a
set of methods for exporting and implementing a device. The action of creating
a slice therefor creates the interface through which a user can access that
device. A driver might even export such slice before the media is present,
in order to make a device node available to the user. (e.g. the floppy
driver would make /dev/rfd0 available even if there was no media present,
simply because it has no way of detecting that the media has been added.
Attempts to open or access that node would result in the usual EIO
errors.

i.e. the device probes, and creates a static 'slice' that is associated with 
the device.. The static slice can't be removed unless the driver does so,
thought if the media is changed the size of the slice may change.


Some time after the media has been detected, or deduced to be present,
the driver would ask the system to try interpret the contents of the 
media. It does this by passing the slice to the generic code. The generic 
code will ask all the possible handlers to see if that slice (or virtual
disk) has the structure it requires. Sometimes the driver (or lower handler,
for that is what the driver is from the point of view of the slice) Will 'seed'
the slice with a 'hint' which will make the generic code narrow it's requests
to a particular handler, or group of handlers.

When a slice object attaches an handler to one of it's slices, that handler
might elect to further export more slices, each representing some different
view of the slice. This could result on a multi layer stack of slices and
handlers, depending on the contents of the device. Whether a handler will
elect to further divide a slice given to it is solely up to that handler. No
other code has jurisdiction over that decision. 

Because a device may need to know that it is being used, it is important
that open() events be cascaded down towards the device. Handlers that 
export multiple slices upwards must pass down the union of all the open
states of those slices.

A lower level handler can decide that the slices it has exported are no
longer valid. This can occur for several reasons. For example a write to a
low level slice might change the structures defining a higher level slice,
or a driver (the lowest level handler) might notice that the media on which
a slice is based, has been removed, or in some other way become
unavailable. The handler must be able to invalidate the slice(es) affected,
and know that the system will cascade that invalidation upwards as needed.
A higher handler may decide to no pass on the invalidation if it calculates
that higher level services can still be provided without the particular
lower slice being present, (e.g. a RAID handler).

Access to various layers is controlled by a strict protocol to avoid
accidental system damage. There is a single sysctl variable that can
disable the enforcement of this protocol, however it should ony be used
in special (e.g. system instalation) circumstances. The basic protocol
is that a higher level device cannot be opened while one of it's lower
layers is open for writing. Similarly, a lower layer cannot be openned for
writing while an upper layer is open at all. Two devices at different
layers can be openned at the same time if there is no direct
decendancy between the two. In an analogue, we might say that 'cousins'
can be openned independantly, but anscestors and descendents cannot.
The sysctl variable kern.slicexclusive has 3 values.
0 disables the checks metioned above.  1 enables them, and 2
enables eve more draconian rules in which even READ opens are disabled.

Further rules govern the interaction of the block and raw versions of a
slice. For example, if a block device is open for read/write, it's raw
device can not be written to (in mode 1)

[think about upwards permission inherritance for subslices]


[setting up new configurations]
A disk exports simply a raw slice. It has no preference as to what goes on it..
(preferences are stored in the slice's probehints structure.)
To slice it into fdisk type:
1/ set the hints to "mbr", through an ioctl on that device. (e.g. rsd0)
2/ Run the "mbr" code's constructor. this will initialise the slice.
   The "mbr" code will actually write an mbr to the slice,
   with default values. (so it will recognise it in the future). 
   (this is why the claim is separate from the constructor). The claim()
   is nondestructive. The constructor KNOWS it owns the slice.
3/ Send ioctls to the device that are redirected UP to the new handler.
   These ioctls allow "type specific templates" and manipulation
   of slice tables. Each hander interprets these to suit it's own table 
   format. This uses the sl_h_upconfig() method, which is basically an
   ioctl entrypoint, but which is not automatically cascaded up.


rc should have the following added to it to make the system 'safe'
when multi-user mode is entered.

*** /etc/rc.orig	Sat Apr 18 14:34:48 1998
--- /etc/rc	Sat Apr 18 14:38:32 1998
***************
*** 82,87 ****
--- 82,96 ----
  	exit 1
  fi
  
+ ###DEVFS
+ # put the storage slices into safe mode.
+ # 0 == unsafe. One char, one blk and one subslice can all be openned R/W.
+ # 1 = readonly. If a subslice is open, a blk and chr can be openned R/O.
+ #                 If a slice is open R/W, subslices cannot be openned.
+ # 2 = exclusive. If a subslice is open, a blk or chr cannot be openned.
+ #                 and visa versa.
+ sysctl -w kern.slicexclusive=1
+ 
  # If there is a global system configuration file, suck it in.
  if [ -f /etc/rc.conf ]; then
      . /etc/rc.conf