d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
471c787259
freebsd-nq/share/doc/IPv6/IMPLEMENTATION
Hajimu UMEMOTO 3384154590 Sync with recent KAME. 
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.

TODO:
  - The definitions of SADB_* in sys/net/pfkeyv2.h are still different
    from RFC2407/IANA assignment because of binary compatibility
    issue.  It should be fixed under 5-CURRENT.
  - ip6po_m member of struct ip6_pktopts is no longer used.  But, it
    is still there because of binary compatibility issue.  It should
    be removed under 5-CURRENT.

Reviewed by:	itojun
Obtained from:	KAME
MFC after:	3 weeks
2001-06-11 12:39:29 +00:00

1923 lines
85 KiB
Plaintext
Raw Blame History

# NOTE: this is from original KAME distribution.
# Some portion of this document is not applicable to the code merged into
# FreeBSD-current (for example, section 5).
Implementation Note
KAME Project
http://www.kame.net/
$KAME: IMPLEMENTATION,v 1.216 2001/05/25 07:43:01 jinmei Exp $
$FreeBSD$
1. IPv6
1.1 Conformance
The KAME kit conforms, or tries to conform, to the latest set of IPv6
specifications. For future reference we list some of the relevant documents
below (NOTE: this is not a complete list - this is too hard to maintain...).
For details please refer to specific chapter in the document, RFCs, manpages
come with KAME, or comments in the source code.
Conformance tests have been performed on past and latest KAME STABLE kit,
at TAHI project. Results can be viewed at http://www.tahi.org/report/KAME/.
We also attended Univ. of New Hampshire IOL tests (http://www.iol.unh.edu/)
in the past, with our past snapshots.
RFC1639: FTP Operation Over Big Address Records (FOOBAR)
* RFC2428 is preferred over RFC1639. ftp clients will first try RFC2428,
then RFC1639 if failed.
RFC1886: DNS Extensions to support IPv6
RFC1933: (see RFC2893)
RFC1981: Path MTU Discovery for IPv6
RFC2080: RIPng for IPv6
* KAME-supplied route6d, bgpd and hroute6d support this.
RFC2283: Multiprotocol Extensions for BGP-4
* so-called "BGP4+".
* KAME-supplied bgpd supports this.
RFC2292: Advanced Sockets API for IPv6
* For supported library functions/kernel APIs, see sys/netinet6/ADVAPI.
RFC2362: Protocol Independent Multicast-Sparse Mode (PIM-SM)
* RFC2362 defines the packet formats and the protcol of PIM-SM.
RFC2373: IPv6 Addressing Architecture
* KAME supports node required addresses, and conforms to the scope
requirement.
RFC2374: An IPv6 Aggregatable Global Unicast Address Format
* KAME supports 64-bit length of Interface ID.
RFC2375: IPv6 Multicast Address Assignments
* Userland applications use the well-known addresses assigned in the RFC.
RFC2428: FTP Extensions for IPv6 and NATs
* RFC2428 is preferred over RFC1639. ftp clients will first try RFC2428,
then RFC1639 if failed.
RFC2460: IPv6 specification
RFC2461: Neighbor discovery for IPv6
* See 1.2 in this document for details.
RFC2462: IPv6 Stateless Address Autoconfiguration
* See 1.4 in this document for details.
RFC2463: ICMPv6 for IPv6 specification
* See 1.8 in this document for details.
RFC2464: Transmission of IPv6 Packets over Ethernet Networks
RFC2465: MIB for IPv6: Textual Conventions and General Group
* Necessary statistics are gathered by the kernel. Actual IPv6 MIB
support is provided as patchkit for ucd-snmp.
RFC2466: MIB for IPv6: ICMPv6 group
* Necessary statistics are gathered by the kernel. Actual IPv6 MIB
support is provided as patchkit for ucd-snmp.
RFC2467: Transmission of IPv6 Packets over FDDI Networks
RFC2472: IPv6 over PPP
RFC2492: IPv6 over ATM Networks
* only PVC is supported.
RFC2497: Transmission of IPv6 packet over ARCnet Networks
RFC2545: Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing
RFC2553: Basic Socket Interface Extensions for IPv6
* IPv4 mapped address (3.7) and special behavior of IPv6 wildcard bind
socket (3.8) are,
- supported and turned on by default on KAME/FreeBSD[34]x
and KAME/BSDI4,
- supported but turned off by default on KAME/NetBSD,
- not supported on KAME/FreeBSD228, KAME/OpenBSD and KAME/BSDI3.
see 1.12 in this document for details.
RFC2671: Extension Mechanisms for DNS (EDNS0)
* see USAGE for how to use it.
* not supported on kame/freebsd4 and kame/bsdi4.
RFC2673: Binary Labels in the Domain Name System
* KAME/bsdi4 supports A6, DNAME and binary label to some extent.
* KAME apps/bind8 repository has resolver library with partial A6, DNAME
and binary label support.
RFC2675: IPv6 Jumbograms
* See 1.7 in this document for details.
RFC2710: Multicast Listener Discovery for IPv6
RFC2711: IPv6 router alert option
RFC2732: Format for Literal IPv6 Addresses in URL's
* The spec is implemented in programs that handle URLs
(like freebsd ftpio(3) and fetch(1), or netbsd ftp(1))
RFC2766: Network Address Translation - Protocol Translation (NAT-PT)
* Section 4.2 is implemented by totd (see ports/totd, or pkgsrc/net/totd).
RFC2874: DNS Extensions to Support IPv6 Address Aggregation and Renumbering
* KAME/bsdi4 supports A6, DNAME and binary label to some extent.
* KAME apps/bind8 repository has resolver library with partial A6, DNAME
and binary label support.
RFC2893: Transition Mechanisms for IPv6 Hosts and Routers
* IPv4 compatible address is not supported.
* automatic tunneling (4.3) is not supported.
* "gif" interface implements IPv[46]-over-IPv[46] tunnel in a generic way,
and it covers "configured tunnel" described in the spec.
See 1.5 in this document for details.
RFC2894: Router renumbering for IPv6
RFC3041: Privacy Extensions for Stateless Address Autoconfiguration in IPv6
RFC3056: Connection of IPv6 Domains via IPv4 Clouds
* So-called "6to4".
* "stf" interface implements it. Be sure to read
draft-itojun-ipv6-transition-abuse-01.txt
below before configuring it, there can be security issues.
draft-ietf-ipngwg-icmp-name-lookups-07: IPv6 Name Lookups Through ICMP
draft-ietf-dhc-dhcpv6-15.txt: DHCPv6
draft-ietf-dhc-dhcpv6exts-12.txt: Extensions for DHCPv6
* kame/dhcp6 has test implementation, which will not be compiled in
default compilation.
* 15/12 drafts are not explicit about padding and string termination.
at IETF48, the author confirmed that there's no padding/termination
(and extensions can appear unaligned). our code follows the comment.
draft-itojun-ipv6-tcp-to-anycast-00.txt:
Disconnecting TCP connection toward IPv6 anycast address
draft-ietf-ipngwg-rfc2553bis-03.txt:
Basic Socket Interface Extensions for IPv6 (revised)
draft-ietf-ipngwg-rfc2292bis-02.txt:
Advanced Sockets API for IPv6 (revised)
* Some of the updates in the draft are not implemented yet. See
TODO.2292bis for more details.
draft-ietf-mobileip-ipv6-13.txt: Mobility Support in IPv6
* See section 6.
draft-ietf-ngtrans-tcpudp-relay-04.txt:
An IPv6-to-IPv4 transport relay translator
* FAITH tcp relay translator (faithd) implements this. See 3.1 for more
details.
draft-ietf-ipngwg-router-selection-01.txt:
Default Router Preferences and More-Specific Routes
* router-side only.
draft-ietf-ipngwg-scoping-arch-02.txt:
The architecture, text representation, and usage of IPv6
scoped addresses.
* some part of the documentation (especially about the routing
model) is not supported yet.
draft-ietf-pim-sm-v2-new-02.txt
A revised version of RFC2362, which includes the IPv6 specific
packet format and protocol descriptions.
draft-ietf-dnsext-mdns-00.txt: Multicast DNS
* kame/mdnsd has test implementation, which will not be built in
default compilation. The draft will experience a major change in the
near future, so don't rely upon it.
draft-itojun-ipv6-transition-abuse-02.txt:
Possible abuse against IPv6 transition technologies (expired)
* KAME does not implement RFC1933/2893 automatic tunnel.
* "stf" interface implements some address filters. Refer to stf(4)
for details. Since there's no way to make 6to4 interface 100% secure,
we do not include "stf" interface into GENERIC.v6 compilation.
* kame/openbsd completely disables IPv4 mapped address support.
* kame/netbsd makes IPv4 mapped address support off by default.
* See section 1.12.6 and 1.14 for more details.
draft-itojun-ipv6-tclass-api-02.txt: Socket API for IPv6 traffic class field
draft-itojun-ipv6-flowlabel-api-01.txt: Socket API for IPv6 flow label field
* no consideration is made against the use of routing headers and such.
1.2 Neighbor Discovery
Neighbor Discovery is fairly stable. Currently Address Resolution,
Duplicated Address Detection, and Neighbor Unreachability Detection
are supported. In the near future we will be adding Unsolicited Neighbor
Advertisement transmission command as admin tool.
Duplicated Address Detection (DAD) will be performed when an IPv6 address
is assigned to a network interface, or the network interface is enabled
(ifconfig up). It is documented in RFC2462 5.4.
If DAD fails, the address will be marked "duplicated" and message will be
generated to syslog (and usually to console). The "duplicated" mark
can be checked with ifconfig. It is administrators' responsibility to check
for and recover from DAD failures. We may try to improve failure recovery
in future KAME code.
DAD procedure may not be effective on certain network interfaces/drivers.
If a network driver needs long initialization time (with wireless network
interfaces this situation is popular), and the driver mistakingly raises
IFF_RUNNING before the driver becomes ready, DAD code will try to transmit
DAD probes to not-really-ready network driver and the packet will not go out
from the interface. In such cases, network drivers should be corrected.
Some of network drivers loop multicast packets back to themselves,
even if instructed not to do so (especially in promiscuous mode).
In such cases DAD may fail, because DAD engine sees inbound NS packet
(actually from the node itself) and considers it as a sign of duplicate.
In this case, drivers should be corrected to honor IFF_SIMPLEX behavior.
For example, you may need to check source MAC address on a inbound packet,
and reject it if it is from the node itself.
You may also want to look at #if condition marked "heuristics" in
sys/netinet6/nd6_nbr.c:nd6_dad_timer() as workaround (note that the code
fragment in "heuristics" section is not spec conformant).
Neighbor Discovery specification (RFC2461) does not talk about neighbor
cache handling in the following cases:
(1) when there was no neighbor cache entry, node received unsolicited
RS/NS/NA/redirect packet without link-layer address
(2) neighbor cache handling on medium without link-layer address
(we need a neighbor cache entry for IsRouter bit)
For (1), we implemented workaround based on discussions on IETF ipngwg mailing
list. For more details, see the comments in the source code and email
thread started from (IPng 7155), dated Feb 6 1999.
IPv6 on-link determination rule (RFC2461) is quite different from assumptions
in BSD IPv4 network code. To implement behavior in RFC2461 section 5.2
(when default router list is empty), the kernel needs to know the default
outgoing interface. To configure the default outgoing interface, use
commands like "ndp -I de0" as root. Note that the spec misuse the word
"host" and "node" in several places in the section.
To avoid possible DoS attacks and infinite loops, KAME stack will accept
only 10 options on ND packet. Therefore, if you have 20 prefix options
attached to RA, only the first 10 prefixes will be recognized.
If this troubles you, please contact KAME team and/or modify
nd6_maxndopt in sys/netinet6/nd6.c. If there are high demands we may
provide sysctl knob for the variable.
Proxy Neighbor Advertisement support is implemented in the kernel.
For instance, you can configure it by using the following command:
# ndp -s fe80::1234%ne0 0:1:2:3:4:5 proxy
where ne0 is the interface which attaches to the same link as the
proxy target.
There are certain limitations, though:
- It does not send unsolicited multicast NA on configuration. This is MAY
behavior in RFC2461.
- It does not add random delay before transmission of solicited NA. This is
SHOULD behavior in RFC2461.
- We cannot configure proxy NDP for off-link address. The target address for
proxying must be link-local address, or must be in prefixes configured to
node which does proxy NDP.
- RFC2461 is unclear about if it is legal for a host to perform proxy ND.
We do not prohibit hosts from doing proxy ND, but there will be very limited
use in it.
Starting mid March 2000, we support Neighbor Unreachability Detection (NUD)
on p2p interfaces, including tunnel interfaces (gif). NUD is turned on by
default. Before March 2000 KAME stack did not perform NUD on p2p interfaces.
If the change raises any interoperability issues, you can turn off/on NUD
by per-interface basis. Use "ndp -i interface -nud" to turn it off.
Consult ndp(8) for details.
RFC2461 specifies upper-layer reachability confirmation hint. Whenever
upper-layer reachability confirmation hint comes, ND process can use it
to optimize neighbor discovery process - ND process can omit real ND exchange
and keep the neighbor cache state in REACHABLE.
We currently have two sources for hints: (1) setsockopt(IPV6_REACHCONF)
defined by 2292bis API, and (2) hints from tcp_input.
It is questionable if they are really trustworthy. For example, a rogue
userland program can use IPV6_REACHCONF to confuse ND process. Neighbor
cache is a system-wide information pool, and it is bad to allow single process
to affect others. Also, tcp_input can be hosed by hijack attempts. It is
wrong to allow hijack attempts to affect ND process.
Starting June 2000, ND code has a protection mechanism against incorrect
upper-layer reachability confirmation. ND code counts subsequent upper-layer
hints. If the number of hints reaches maximum, ND code will ignore further
upper-layer hints and run real ND process to confirm reachability to the peer.
sysctl net.inet6.icmp6.nd6_maxnudhint defines maximum # of subsequent
upper-layer hints to be accepted.
(from April 2000 to June 2000, we rejected setsockopt(IPV6_REACHCONF) from
non-root process - after local discussion, it looks that hints are not
that trustworthy even if they are from privileged processes)
If inbound ND packets carry invalid values, the KAME kernel will
drop these packet and increment statistics variable. See
"netstat -sn", icmp6 section. For detailed debugging session, you can
turn on syslog output from the kernel on errors, by turning on sysctl MIB
net.inet6.icmp6.nd6_debug. nd6_debug can be turned on at bootstrap
time, by defining ND6_DEBUG kernel compilation option (so you can
debug behavior during bootstrap). nd6_debug configuration should
only be used for test/debug purposes - for production environment,
nd6_debug must be set to 0. If you leave it to 1, malicious parties
can inject broken packet and fill up /var/log partition.
1.3 Scope Zone Index
IPv6 uses scoped addresses. It is therefore very important to
specify the scope zone index (link index for a link-local address, or
site index for a site-local address) with an IPv6 address. Without a
zone index, a scoped IPv6 address is ambiguous to the kernel, and
the kernel would not be able to determine the outbound link for a
packet to the scoped address. KAME code tries to address the issue in
several ways.
The entire architecture of scoped addresses is documented in
draft-ietf-ipngwg-scoping-arch-xx.txt. One non-trivial point of the
architecture is that the link scope is (theoretically) larger than the
interface scope. That is, two different interfaces can belong to a
same single link. However, in a normal operation, we can assume that
there is 1-to-1 relationship between links and interfaces. In
other words, we can usually put links and interfaces in the same scope
type. The current KAME implementation assumes the 1-to-1
relationship. In particular, we use interface names such as "ne1" as
unique link identifiers. This would be much more human-readable and
intuitive than numeric identifiers, but please keep your mind on the
theoretical difference between links and interfaces.
Site-local addresses are very vaguely defined in the specs, and both
the specification and the KAME code need tons of improvements to
enable its actual use. For example, it is still very unclear how we
define a site, or how we resolve host names in a site. There is work
underway to define behavior of routers at site border, but, we have
almost no code for site boundary node support (both forwarding nor
routing) and we bet almost noone has. We recommend, at this moment,
you to use global addresses for experiments - there are way too many
pitfalls if you use site-local addresses.
1.3.1 Kernel internal
In the kernel, the link index for a link-local scope address is
embedded into the 2nd 16bit-word (the 3rd and 4th bytes) in the IPv6
address.
For example, you may see something like:
fe80:1::200:f8ff:fe01:6317
in the routing table and the interface address structure (struct
in6_ifaddr). The address above is a link-local unicast address which
belongs to a network link whose link identifier is 1 (note that it
eqauls to the interface index by the assumption of our
implementation). The embedded index enables us to identify IPv6
link-local addresses over multiple links effectively and with only a
little code change.
1.3.2 Interaction with API
There are several candidates of API to deal with scoped addresses
without ambiguity.
The IPV6_PKTINFO ancillary data type or socket option defined in the
advanced API (RFC2292 or draft-ietf-ipngwg-rfc2292bis-xx) can specify
the outgoing interface of a packet. Similarly, the IPV6_PKTINFO or
IPV6_RECVPKTINFO socket options tell kernel to pass the incoming
interface to user applications.
These options are enough to disambiguate scoped addresses of an
incoming packet, because we can uniquely identify the corresponding
zone of the scoped address(es) by the incoming interface. However,
they are too strong for outgoing packets. For example, consider a
multi-sited node and suppose that more than one interface of the node
belongs to a same site. When we want to send a packet to the site,
we can only specify one of the interfaces for the outgoing packet with
these options; we cannot just say "send the packet to (one of the
interfaces of) the site."
Another kind of candidates is to use the sin6_scope_id member in the
sockaddr_in6 structure, defined in RFC2553 and
draft-ietf-ipngwg-rfc2553bis-xx.txt. The KAME kernel interprets the
sin6_scope_id field properly in order to disambiguate scoped
addresses. For example, if an application passes a sockaddr_in6
structure that has a non-zero sin6_scope_id value to the sendto(2)
system call, the kernel should send the packet to the appropriate zone
according to the sin6_scope_id field. Similarly, when the source or
the destination address of an incoming packet is a scoped one, the
kernel should detect the correct zone identifier based on the address
and the receiving interface, fill the identifier in the sin6_scope_id
field of a sockaddr_in6 structure, and then pass the packet to an
application via the recvfrom(2) system call, etc.
However, the semantics of the sin6_scope_id is still vague and on the
way to standardization. Additionally, not so many operating systems
support the behavior above at this moment.
In summary,
- If your target system is limited to KAME based ones (i.e. BSD
variants and KAME snaps), use the sin6_scope_id field assuming the
kernel behavior described above.
- Otherwise, (i.e. if your program should be portable on other systems
than BSDs)
+ Use the advanced API to disambiguate scoped addresses of incoming
packets.
+ To disambiguate scoped addresses of outgoing packets,
* if it is okay to just specify the outgoing interface, use the
advanced API. This would be the case, for example, when you
should only consider link-local addresses and your system
assumes 1-to-1 relationship between links and interfaces.
* otherwise, sorry but you lose. Please rush the IETF IPv6
community into standardizing the semantics of the sin6_scope_id
field.
Routing daemons and configuration programs, like route6d and ifconfig,
will need to manipulate the "embedded" zone index. These programs use
routing sockets and ioctls (like SIOCGIFADDR_IN6) and the kernel API
will return IPv6 addresses with the 2nd 16bit-word filled in. The
APIs are for manipulating kernel internal structure. Programs that
use these APIs have to be prepared about differences in kernels
anyway.
getaddrinfo(3) and getnameinfo(3) support an extended numeric IPv6
syntax, as documented in draft-ietf-ipngwg-rfc2553bis-xx.txt. You can
specify the outgoing link, by using the name of the outgoing interface
as the link, like "fe80::1%ne0" (again, note that we assume there is
1-to-1 relationship between links and interfaces.) This way you will
be able to specify a link-local scoped address without much trouble.
Other APIs like inet_pton(3) and inet_ntop(3) are inherently
unfriendly with scoped addresses, since they are unable to annotate
addresses with zone identifier.
1.3.3 Interaction with users (command line)
Most of user applications now support the extended numeric IPv6
syntax. In this case, you can specify outgoing link, by using the name
of the outgoing interface like "fe80::1%ne0" (sorry for the duplicated
notice, but please recall again that we assume 1-to-1 relationship
between links and interfaces). This is even the case for some
management tools such as route(8) or ndp(8). For example, to install
the IPv6 default route by hand, you can type like
# route add -inet6 default fe80::9876:5432:1234:abcd%ne0
(Although we suggest you to run dynamic routing instead of static
routes, in order to avoid configuration mistakes.)
Some applications have command line options for specifying an
appropriate zone of a scoped address (like "ping6 -I ne0 ff02::1" to
specify the outgoing interface). However, you can't always expect such
options. Thus, we recommend you to use the extended format described
above.
In any case, when you specify a scoped address to the command line,
NEVER write the embedded form (such as ff02:1::1 or fe80:2::fedc),
which should only be used inside the kernel (see Section 1.3.1), and
is not supposed to work.
1.4 Plug and Play
The KAME kit implements most of the IPv6 stateless address
autoconfiguration in the kernel.
Neighbor Discovery functions are implemented in the kernel as a whole.
Router Advertisement (RA) input for hosts is implemented in the
kernel. Router Solicitation (RS) output for endhosts, RS input
for routers, and RA output for routers are implemented in the
userland.
1.4.1 Assignment of link-local, and special addresses
IPv6 link-local address is generated from IEEE802 address (ethernet MAC
address). Each of interface is assigned an IPv6 link-local address
automatically, when the interface becomes up (IFF_UP). Also, direct route
for the link-local address is added to routing table.
Here is an output of netstat command:
Internet6:
Destination Gateway Flags Netif Expire
fe80::%ed0/64 link#1 UC ed0
fe80::%ep0/64 link#2 UC ep0
Interfaces that has no IEEE802 address (pseudo interfaces like tunnel
interfaces, or ppp interfaces) will borrow IEEE802 address from other
interfaces, such as ethernet interfaces, whenever possible.
If there is no IEEE802 hardware attached, last-resort pseudorandom value,
which is from MD5(hostname), will be used as source of link-local address.
If it is not suitable for your usage, you will need to configure the
link-local address manually.
If an interface is not capable of handling IPv6 (such as lack of multicast
support), link-local address will not be assigned to that interface.
See section 2 for details.
Each interface joins the solicited multicast address and the
link-local all-nodes multicast addresses (e.g. fe80::1:ff01:6317
and ff02::1, respectively, on the link the interface is attached).
In addition to a link-local address, the loopback address (::1) will be
assigned to the loopback interface. Also, ::1/128 and ff01::/32 are
automatically added to routing table, and loopback interface joins
node-local multicast group ff01::1.
1.4.2 Stateless address autoconfiguration on hosts
In IPv6 specification, nodes are separated into two categories:
routers and hosts. Routers forward packets addressed to others, hosts does
not forward the packets. net.inet6.ip6.forwarding defines whether this
node is a router or a host (router if it is 1, host if it is 0).
It is NOT recommended to change net.inet6.ip6.forwarding while the node
is in operation. IPv6 specification defines behavior for "host" and "router"
quite differently, and switching from one to another can cause serious
troubles. It is recommended to configure the variable at bootstrap time only.
The first step in stateless address configuration is Duplicated Address
Detection (DAD). See 1.2 for more detail on DAD.
When a host hears Router Advertisement from the router, a host may
autoconfigure itself by stateless address autoconfiguration.
This behavior can be controlled by net.inet6.ip6.accept_rtadv
(host autoconfigures itself if it is set to 1).
By autoconfiguration, network address prefix for the receiving interface
(usually global address prefix) is added. The default route is also
configured.
Routers periodically generate Router Advertisement packets. To
request an adjacent router to generate RA packet, a host can transmit
Router Solicitation. To generate an RS packet at any time, use the
"rtsol" command. The "rtsold" daemon is also available. "rtsold"
generates Router Solicitation whenever necessary, and it works great
for nomadic usage (notebooks/laptops). If one wishes to ignore Router
Advertisements, use sysctl to set net.inet6.ip6.accept_rtadv to 0.
To generate Router Advertisement from a router, use the "rtadvd" daemon.
Note that the IPv6 specification assumes the following items and that
nonconforming cases are left unspecified:
- Only hosts will listen to router advertisements
- Hosts have single network interface (except loopback)
This is therefore unwise to enable net.inet6.ip6.accept_rtadv on routers,
or multi-interface host. A misconfigured node can behave strange
(KAME code allows nonconforming configuration, for those who would like
to do some experiments).
To summarize the sysctl knob:
accept_rtadv forwarding role of the node
--- --- ---
0 0 host (to be manually configured)
0 1 router
1 0 autoconfigured host
(spec assumes that host has single
interface only, autoconfigred host with
multiple interface is out-of-scope)
1 1 invalid, or experimental
(out-of-scope of spec)
See 1.2 in the document for relationship between DAD and autoconfiguration.
1.4.3 DHCPv6
We supply a tiny DHCPv6 server/client in kame/dhcp6. However, the
implementation is premature (for example, this does NOT implement
address lease/release), and it is not in default compilation tree on
some platforms. If you want to do some experiment, compile it on your
own.
DHCPv6 and autoconfiguration also needs more work. "Managed" and "Other"
bits in RA have no special effect to stateful autoconfiguration procedure
in DHCPv6 client program ("Managed" bit actually prevents stateless
autoconfiguration, but no special action will be taken for DHCPv6 client).
1.5 Generic tunnel interface
GIF (Generic InterFace) is a pseudo interface for configured tunnel.
Details are described in gif(4) manpage.
Currently
v6 in v6
v6 in v4
v4 in v6
v4 in v4
are available. Use "gifconfig" to assign physical (outer) source
and destination address to gif interfaces.
Configuration that uses same address family for inner and outer IP
header (v4 in v4, or v6 in v6) is dangerous. It is very easy to
configure interfaces and routing tables to perform infinite level
of tunneling. Please be warned.
gif can be configured to be ECN-friendly. See 4.5 for ECN-friendliness
of tunnels, and gif(4) manpage for how to configure.
If you would like to configure an IPv4-in-IPv6 tunnel with gif interface,
read gif(4) carefully. You may need to remove IPv6 link-local address
automatically assigned to the gif interface.
1.6 Source Address Selection
KAME's source address selection takes care of the following
conditions:
- address scope
- outgoing interface
- whether an address is deprecated
- whether an address is temporary (in terms of RFC 3041)
- prefix matching against the destination
Roughly speaking, the selection policy is as follows:
- always use an address that belongs to the same scope zone as the
destination.
- addresses that have equal or larger scope than the scope of the
destination are preferred.
- a deprecated address is not used in new communications if an
alternate (non-deprecated) address is available and has sufficient
scope.
- a temporary address (in terms of RFC 3041 privacy extension) are
preferred to a public address.
- if none of above conditions tie-breaks, addresses assigned on the
outgoing interface are preferred.
- if none of above conditions tie-breaks, one which is longest prefix
matching against the destination is preferred as the last resort.
For instance, ::1 is selected for ff01::1,
fe80::200:f8ff:fe01:6317%ne0 for fe80::2a0:24ff:feab:839b%ne0.
To see how longest-matching works, suppose that
3ffe:501:808:1:200:f8ff:fe01:6317 and 3ffe:2001:9:124:200:f8ff:fe01:6317
are given on the outgoing interface. Then the former is chosen as the
source for the destination 3ffe:501:800::1. Note that even if all
available addresses have smaller scope than the scope of the
destination, we choose one anyway. For example, if we have link-local
and site-local addresses only, we choose a site-local addresses for a
global destination. If the packet is going to break a site boundary,
the boundary router will return an ICMPv6 destination unreachable
error with code 2 - beyond scope of source address.
The precise desripction of the algorithm is quite complicated. To
describe the algorithm, we introduce the following notation:
For a given destination D,
samescope(D): The set of addresses that have the same scope as D.
largerscope(D): The set of addresses that have a larger scope than D.
smallerscope(D): The set of addresses that have a smaller scope than D.
For a given set of addresses A,
DEP(A): the set of deprecated addresses in A.
nonDEP(A): A - DEP(A).
For a given set of addresses A,
tmp(A): the set of preferred temporary-autoconfigured or
manually-configure addresses in A.
Also, the algorithm assumes that the outgoing interface for the
destination D is determined. We call the interface "I".
The algorithm is as follows. Selection proceeds step by step as
described; For example, if an address is selected by item 1, item 2 and
later are not considered at all.
0. If there is no address in the same scope zone as D, just give up;
the packet will not be sent.
1. If we do not prefer temporary addresses, go to 3.
Otherwise, and if tmp(samescope(D)) is not empty,
then choose an address that is on the interface I. If every
address is on I, or every address is on a different interface
from I, choose an arbitrary one provided that an address longest
matching against D is always preferred.
2. If tmp(largerscope(D)) is not empty,
then choose an address that has the smallest scope. If more than one
address has the smallest scope, choose an arbitrary one provided
that addresses on I are always preferred.
3. If nonDEP(samescope(D)) is not empty,
then apply the same logic as of 1.
4. If nonDEP(largerscope(D)) is not empty,
then apply the same logic as of 2.
5. If we do not prefer temporary addresses, go to 7.
Otherwise, and if tmp(DEP(samescope(D))) is not empty,
then choose an address that is on the interface I. If every
address is on I, or every address is on a different interface
from I, choose an arbitrary one provided that an address longest
matching against D is always preferred.
6. If tmp(DEP(largerscope(D))) is not empty,
then choose an address that has the smallest scope. If more than
one address has the smallest scope, choose an arbitrary one provided
that an address on I is always preferred.
7. If DEP(samescope(D)) is not empty,
then apply the same logic as of 5.
8. If DEP(largerscope(D)) is not empty,
then apply the same logic as of 6.
9. If we do not prefer temporary addresses, go to 11.
Otherwise, and if tmp(nonDEP(smallerscope(D))) is not empty,
then choose an address that has the largest scope. If more than
one address has the largest scope, choose an arbitrary one provided
that an address on I is always preferred.
10. If tmp(DEP(smallerscope(D))) is not empty,
then choose an address that has the largest scope. If more than
one address has the largest scope, choose an arbitrary one provided
that an address on I is always preferred.
11. If nonDEP(smallerscope(D)) is not empty,
then apply the same logic as of 9.
12. If DEP(smallerscope(D)) is not empty,
then apply the same logic as of 10.
There exists a document about source address selection
(draft-ietf-ipngwg-default-addr-select-xx.txt). KAME's algorithm
described above takes a similar approach to the document, but there
are some differences. See the document for more details.
There are some cases where we do not use the above rule. One
example is connected TCP session, and we use the address kept in TCP
protocol control block (tcb) as the source.
Another example is source address for Neighbor Advertisement.
Under the spec (RFC2461 7.2.2) NA's source should be the target
address of the corresponding NS's target. In this case we follow
the spec rather than the above longest-match rule.
If you would like to prohibit the use of deprecated address for some
reason, configure net.inet6.ip6.use_deprecated to 0. The issue
related to deprecated address is described in RFC2462 5.5.4 (NOTE:
there is some debate underway in IETF ipngwg on how to use
"deprecated" address).
1.7 Jumbo Payload
KAME supports the Jumbo Payload hop-by-hop option used to send IPv6
packets with payloads longer than 65,535 octets. But since currently
KAME does not support any physical interface whose MTU is more than
65,535, such payloads can be seen only on the loopback interface(i.e.
lo0).
If you want to try jumbo payloads, you first have to reconfigure the
kernel so that the MTU of the loopback interface is more than 65,535
bytes; add the following to the kernel configuration file:
options "LARGE_LOMTU" #To test jumbo payload
and recompile the new kernel.
Then you can test jumbo payloads by the ping6 command with -b and -s
options. The -b option must be specified to enlarge the size of the
socket buffer and the -s option specifies the length of the packet,
which should be more than 65,535. For example, type as follows;
% ping6 -b 70000 -s 68000 ::1
The IPv6 specification requires that the Jumbo Payload option must not
be used in a packet that carries a fragment header. If this condition
is broken, an ICMPv6 Parameter Problem message must be sent to the
sender. KAME kernel follows the specification, but you cannot usually
see an ICMPv6 error caused by this requirement.
If KAME kernel receives an IPv6 packet, it checks the frame length of
the packet and compares it to the length specified in the payload
length field of the IPv6 header or in the value of the Jumbo Payload
option, if any. If the former is shorter than the latter, KAME kernel
discards the packet and increments the statistics. You can see the
statistics as output of netstat command with `-s -p ip6' option:
% netstat -s -p ip6
ip6:
(snip)
1 with data size < data length
So, KAME kernel does not send an ICMPv6 error unless the erroneous
packet is an actual Jumbo Payload, that is, its packet size is more
than 65,535 bytes. As described above, KAME kernel currently does not
support physical interface with such a huge MTU, so it rarely returns an
ICMPv6 error.
TCP/UDP over jumbogram is not supported at this moment. This is because
we have no medium (other than loopback) to test this. Contact us if you
need this.
IPsec does not work on jumbograms. This is due to some specification twists
in supporting AH with jumbograms (AH header size influences payload length,
and this makes it real hard to authenticate inbound packet with jumbo payload
option as well as AH).
There are fundamental issues in *BSD support for jumbograms. We would like to
address those, but we need more time to finalize the task. To name a few:
- mbuf pkthdr.len field is typed as "int" in 4.4BSD, so it cannot hold
jumbogram with len > 2G on 32bit architecture CPUs. If we would like to
support jumbogram properly, the field must be expanded to hold 4G +
IPv6 header + link-layer header. Therefore, it must be expanded to at least
int64_t (u_int32_t is NOT enough).
- We mistakingly use "int" to hold packet length in many places. We need
to convert them into larger numeric type. It needs a great care, as we may
experience overflow during packet length computation.
- We mistakingly check for ip6_plen field of IPv6 header for packet payload
length in various places. We should be checking mbuf pkthdr.len instead.
ip6_input() will perform sanity check on jumbo payload option on input,
and we can safely use mbuf pkthdr.len afterwards.
- TCP code needs careful updates in bunch of places, of course.
1.8 Loop prevention in header processing
IPv6 specification allows arbitrary number of extension headers to
be placed onto packets. If we implement IPv6 packet processing
code in the way BSD IPv4 code is implemented, kernel stack may
overflow due to long function call chain. KAME sys/netinet6 code
is carefully designed to avoid kernel stack overflow. Because of
this, KAME sys/netinet6 code defines its own protocol switch
structure, as "struct ip6protosw" (see netinet6/ip6protosw.h).
In addition to this, we restrict the number of extension headers
(including the IPv6 header) in each incoming packet, in order to
prevent a DoS attack that tries to send packets with a massive number
of extension headers. The upper limit can be configured by the sysctl
value net.inet6.ip6.hdrnestlimit. In particular, if the value is 0,
the node will allow an arbitrary number of headers. As of writing this
document, the default value is 50.
IPv4 part (sys/netinet) remains untouched for compatibility.
Because of this, if you receive IPsec-over-IPv4 packet with massive
number of IPsec headers, kernel stack may blow up. IPsec-over-IPv6 is okay.
1.9 ICMPv6
After RFC2463 was published, IETF ipngwg has decided to disallow ICMPv6 error
packet against ICMPv6 redirect, to prevent ICMPv6 storm on a network medium.
KAME already implements this into the kernel.
RFC2463 requires rate limitation for ICMPv6 error packets generated by a
node, to avoid possible DoS attacks. KAME kernel implements two rate-
limitation mechanisms, tunable via sysctl:
- Minimum time interval between ICMPv6 error packets
KAME kernel will generate no more than one ICMPv6 error packet,
during configured time interval. net.inet6.icmp6.errratelimit
controls the interval (default: disabled).
- Maximum ICMPv6 error packet-per-second
KAME kernel will generate no more than the configured number of
packets in one second. net.inet6.icmp6.errppslimit controls the
maximum packet-per-second value (default: 200pps)
Basically, we need to pick values that are suitable against the bandwidth
of link layer devices directly attached to the node. In some cases the
default values may not fit well. We are still unsure if the default value
is sane or not. Comments are welcome.
1.10 Applications
For userland programming, we support IPv6 socket API as specified in
RFC2553, RFC2292 and upcoming internet drafts.
TCP/UDP over IPv6 is available and quite stable. You can enjoy "telnet",
"ftp", "rlogin", "rsh", "ssh", etc. These applications are protocol
independent. That is, they automatically chooses IPv4 or IPv6
according to DNS.
1.11 Kernel Internals
(*) TCP/UDP part is handled differently between operating system platforms.
See 1.12 for details.
The current KAME has escaped from the IPv4 netinet logic. While
ip_forward() calls ip_output(), ip6_forward() directly calls
if_output() since routers must not divide IPv6 packets into fragments.
ICMPv6 should contain the original packet as long as possible up to
1280. UDP6/IP6 port unreach, for instance, should contain all
extension headers and the *unchanged* UDP6 and IP6 headers.
So, all IP6 functions except TCP6 never convert network byte
order into host byte order, to save the original packet.
tcp6_input(), udp6_input() and icmp6_input() can't assume that IP6
header is preceding the transport headers due to extension
headers. So, in6_cksum() was implemented to handle packets whose IP6
header and transport header is not continuous. TCP/IP6 nor UDP/IP6
header structure don't exist for checksum calculation.
To process IP6 header, extension headers and transport headers easily,
KAME requires network drivers to store packets in one internal mbuf or
one or more external mbufs. A typical old driver prepares two
internal mbufs for 100 - 208 bytes data, however, KAME's reference
implementation stores it in one external mbuf.
"netstat -s -p ip6" tells you whether or not your driver conforms
KAME's requirement. In the following example, "cce0" violates the
requirement. (For more information, refer to Section 2.)
Mbuf statistics:
317 one mbuf
two or more mbuf::
lo0 = 8
cce0 = 10
3282 one ext mbuf
0 two or more ext mbuf
Each input function calls IP6_EXTHDR_CHECK in the beginning to check
if the region between IP6 and its header is
continuous. IP6_EXTHDR_CHECK calls m_pullup() only if the mbuf has
M_LOOP flag, that is, the packet comes from the loopback
interface. m_pullup() is never called for packets coming from physical
network interfaces.
TCP6 reassembly makes use of IP6 header to store reassemble
information. IP6 is not supposed to be just before TCP6, so
ip6tcpreass structure has a pointer to TCP6 header. Of course, it has
also a pointer back to mbuf to avoid m_pullup().
Like TCP6, both IP and IP6 reassemble functions never call m_pullup().
xxx_ctlinput() calls in_mrejoin() on PRC_IFNEWADDR. We think this is
one of 4.4BSD implementation flaws. Since 4.4BSD keeps ia_multiaddrs
in in_ifaddr{}, it can't use multicast feature if the interface has no
unicast address. So, if an application joins to an interface and then
all unicast addresses are removed from the interface, the application
can't send/receive any multicast packets. Moreover, if a new unicast
address is assigned to the interface, in_mrejoin() must be called.
KAME's interfaces, however, have ALWAYS one link-local unicast
address. These extensions have thus not been implemented in KAME.
1.12 IPv4 mapped address and IPv6 wildcard socket
RFC2553 describes IPv4 mapped address (3.7) and special behavior
of IPv6 wildcard bind socket (3.8). The spec allows you to:
- Accept IPv4 connections by AF_INET6 wildcard bind socket.
- Transmit IPv4 packet over AF_INET6 socket by using special form of
the address like ::ffff:10.1.1.1.
but the spec itself is very complicated and does not specify how the
socket layer should behave.
Here we call the former one "listening side" and the latter one "initiating
side", for reference purposes.
Almost all KAME implementations treat tcp/udp port number space separately
between IPv4 and IPv6. You can perform wildcard bind on both of the address
families, on the same port.
There are some OS-platform differences in KAME code, as we use tcp/udp
code from different origin. The following table summarizes the behavior.
listening side initiating side
(AF_INET6 wildcard (connection to ::ffff:10.1.1.1)
socket gets IPv4 conn.)
--- ---
KAME/BSDI3 not supported not supported
KAME/FreeBSD228 not supported not supported
KAME/FreeBSD3x configurable supported
default: enabled
KAME/FreeBSD4x configurable supported
default: enabled
KAME/NetBSD configurable supported
default: disabled
KAME/BSDI4 enabled supported
KAME/OpenBSD not supported not supported
The following sections will give you more details, and how you can
configure the behavior.
Comments on listening side:
It looks that RFC2553 talks too little on wildcard bind issue,
specifically on (1) port space issue, (2) failure mode, (3) relationship
between AF_INET/INET6 wildcard bind like ordering constraint, and (4) behavior
when conflicting socket is opened/closed. There can be several separate
interpretation for this RFC which conform to it but behaves differently.
So, to implement portable application you should assume nothing
about the behavior in the kernel. Using getaddrinfo() is the safest way.
Port number space and wildcard bind issues were discussed in detail
on ipv6imp mailing list, in mid March 1999 and it looks that there's
no concrete consensus (means, up to implementers). You may want to
check the mailing list archives.
We supply a tool called "bindtest" that explores the behavior of
kernel bind(2). The tool will not be compiled by default.
If a server application would like to accept IPv4 and IPv6 connections,
it should use AF_INET and AF_INET6 socket (you'll need two sockets).
Use getaddrinfo() with AI_PASSIVE into ai_flags, and socket(2) and bind(2)
to all the addresses returned.
By opening multiple sockets, you can accept connections onto the socket with
proper address family. IPv4 connections will be accepted by AF_INET socket,
and IPv6 connections will be accepted by AF_INET6 socket (NOTE: KAME/BSDI4
kernel sometimes violate this - we will fix it).
If you try to support IPv6 traffic only and would like to reject IPv4
traffic, always check the peer address when a connection is made toward
AF_INET6 listening socket. If the address is IPv4 mapped address, you may
want to reject the connection. You can check the condition by using
IN6_IS_ADDR_V4MAPPED() macro. This is one of the reasons the author of
the section (itojun) dislikes special behavior of AF_INET6 wildcard bind.
Comments on initiating side:
Advise to application implementers: to implement a portable IPv6 application
(which works on multiple IPv6 kernels), we believe that the following
is the key to the success:
- NEVER hardcode AF_INET nor AF_INET6.
- Use getaddrinfo() and getnameinfo() throughout the system.
Never use gethostby*(), getaddrby*(), inet_*() or getipnodeby*().
- If you would like to connect to destination, use getaddrinfo() and try
all the destination returned, like telnet does.
- Some of the IPv6 stack is shipped with buggy getaddrinfo(). Ship a minimal
working version with your application and use that as last resort.
If you would like to use AF_INET6 socket for both IPv4 and IPv6 outgoing
connection, you will need tweaked implementation in DNS support libraries,
as documented in RFC2553 6.1. KAME libinet6 includes the tweak in
getipnodebyname(). Note that getipnodebyname() itself is not recommended as
it does not handle scoped IPv6 addresses at all. For IPv6 name resolution
getaddrinfo() is the preferred API. getaddrinfo() does not implement the
tweak.
When writing applications that make outgoing connections, story goes much
simpler if you treat AF_INET and AF_INET6 as totally separate address family.
{set,get}sockopt issue goes simpler, DNS issue will be made simpler. We do
not recommend you to rely upon IPv4 mapped address.
1.12.1 KAME/BSDI3 and KAME/FreeBSD228
The platforms do not support IPv4 mapped address at all (both listening side
and initiating side). AF_INET6 and AF_INET sockets are totally separated.
Port number space is totally separate between AF_INET and AF_INET6 sockets.
It should be noted that KAME/BSDI3 and KAME/FreeBSD228 are not conformant
to RFC2553 section 3.7 and 3.8. It is due to code sharing reasons.
1.12.2 KAME/FreeBSD[34]x
KAME/FreeBSD3x and KAME/FreeBSD4x use shared tcp4/6 code (from
sys/netinet/tcp*) and shared udp4/6 code (from sys/netinet/udp*).
They use unified inpcb/in6pcb structure.
1.12.2.1 KAME/FreeBSD[34]x, listening side
The platform can be configured to support IPv4 mapped address/special
AF_INET6 wildcard bind (enabled by default). There is no kernel compilation
option to disable it. You can enable/disable the behavior with sysctl
(per-node), or setsockopt (per-socket).
Wildcard AF_INET6 socket grabs IPv4 connection if and only if the following
conditions are satisfied:
- there's no AF_INET socket that matches the IPv4 connection
- the AF_INET6 socket is configured to accept IPv4 traffic, i.e.
getsockopt(IPV6_V6ONLY) returns 0.
(XXX need checking)
1.12.2.2 KAME/FreeBSD[34]x, initiating side
KAME/FreeBSD3x supports outgoing connection to IPv4 mapped address
(::ffff:10.1.1.1), if the node is configured to accept IPv4 connections
by AF_INET6 socket.
(XXX need checking)
1.12.3 KAME/NetBSD
KAME/NetBSD uses shared tcp4/6 code (from sys/netinet/tcp*) and shared
udp4/6 code (from sys/netinet/udp*). The implementation is made differently
from KAME/FreeBSD[34]x. KAME/NetBSD uses separate inpcb/in6pcb structures,
while KAME/FreeBSD[34]x uses merged inpcb structure.
It should be noted that the default configuration of KAME/NetBSD is not
conformant to RFC2553 section 3.8. It is intentionally turned off by default
for security reasons.
1.12.3.1 KAME/NetBSD, listening side
The platform can be configured to support IPv4 mapped address/special AF_INET6
wildcard bind (disabled by default). Kernel behavior can be summarized as
follows:
- default: special support code will be compiled in, but is disabled by
default. It can be controlled by sysctl (net.inet6.ip6.v6only),
or setsockopt(IPV6_V6ONLY).
- add "INET6_V6ONLY": No special support code for AF_INET6 wildcard socket
will be compiled in. AF_INET6 sockets and AF_INET sockets are totally
separate. The behavior is similar to what described in 1.12.1.
sysctl setting will affect per-socket configuration at in6pcb creation time
only. In other words, per-socket configuration will be copied from sysctl
configuration at in6pcb creation time. To change per-socket behavior, you
must perform setsockopt or reopen the socket. Change in sysctl configuration
will not change the behavior or sockets that are already opened.
Wildcard AF_INET6 socket grabs IPv4 connection if and only if the following
conditions are satisfied:
- there's no AF_INET socket that matches the IPv4 connection
- the AF_INET6 socket is configured to accept IPv4 traffic, i.e.
getsockopt(IPV6_V6ONLY) returns 0.
You cannot bind(2) with IPv4 mapped address. This is a workaround for port
number duplicate and other twists.
1.12.3.2 KAME/NetBSD, initiating side
When you initiate a connection, you can always connect to IPv4 destination
over AF_INET6 socket, usin IPv4 mapped address destination (::ffff:10.1.1.1).
This is enabled independently from the configuration for listening side, and
always enabled.
1.12.4 KAME/BSDI4
KAME/BSDI4 uses NRL-based TCP/UDP stack and inpcb source code,
which was derived from NRL IPv6/IPsec stack. We guess it supports IPv4 mapped
address and speical AF_INET6 wildcard bind. The implementation is, again,
different from other KAME/*BSDs.
1.12.4.1 KAME/BSDI4, listening side
NRL inpcb layer supports special behavior of AF_INET6 wildcard socket.
There is no way to disable the behavior.
Wildcard AF_INET6 socket grabs IPv4 connection if and only if the following
condition is satisfied:
- there's no AF_INET socket that matches the IPv4 connection
1.12.4.2 KAME/BSDI4, initiating side
KAME/BSDi4 supports connection initiation to IPv4 mapped address
(like ::ffff:10.1.1.1).
1.12.5 KAME/OpenBSD
KAME/OpenBSD uses NRL-based TCP/UDP stack and inpcb source code,
which was derived from NRL IPv6/IPsec stack.
It should be noted that KAME/OpenBSD is not conformant to RFC2553 section 3.7
and 3.8. It is intentionally omitted for security reasons.
1.12.5.1 KAME/OpenBSD, listening side
KAME/OpenBSD disables special behavior on AF_INET6 wildcard bind for
security reasons (if IPv4 traffic toward AF_INET6 wildcard bind is allowed,
access control will become much harder). KAME/BSDI4 uses NRL-based TCP/UDP
stack as well, however, the behavior is different due to OpenBSD's security
policy.
As a result the behavior of KAME/OpenBSD is similar to KAME/BSDI3 and
KAME/FreeBSD228 (see 1.12.1 for more detail).
1.12.5.2 KAME/OpenBSD, initiating side
KAME/OpenBSD does not support connection initiation to IPv4 mapped address
(like ::ffff:10.1.1.1).
1.12.6 More issues
IPv4 mapped address support adds a big requirement to EVERY userland codebase.
Every userland code should check if an AF_INET6 sockaddr contains IPv4
mapped address or not. This adds many twists:
- Access controls code becomes harder to write.
For example, if you would like to reject packets from 10.0.0.0/8,
you need to reject packets to AF_INET socket from 10.0.0.0/8,
and to AF_INET6 socket from ::ffff:10.0.0.0/104.
- If a protocol on top of IPv4 is defined differently with IPv6, we need to be
really careful when we determine which protocol to use.
For example, with FTP protocol, we can not simply use sa_family to determine
FTP command sets. The following example is incorrect:
if (sa_family == AF_INET)
use EPSV/EPRT or PASV/PORT; /*IPv4*/
else if (sa_family == AF_INET6)
use EPSV/EPRT or LPSV/LPRT; /*IPv6*/
else
error;
The correct code, with consideration to IPv4 mapped address, would be:
if (sa_family == AF_INET)
use EPSV/EPRT or PASV/PORT; /*IPv4*/
else if (sa_family == AF_INET6 && IPv4 mapped address)
use EPSV/EPRT or PASV/PORT; /*IPv4 command set on AF_INET6*/
else if (sa_family == AF_INET6 && !IPv4 mapped address)
use EPSV/EPRT or LPSV/LPRT; /*IPv6*/
else
error;
It is too much to ask for every body to be careful like this.
The problem is, we are not sure if the above code fragment is perfect for
all situations.
- By enabling kernel support for IPv4 mapped address (outgoing direction),
servers on the kernel can be hosed by IPv6 native packet that has IPv4
mapped address in IPv6 header source, and can generate unwanted IPv4 packets.
draft-itojun-ipv6-transition-abuse-01.txt talks more about this scenario.
Due to the above twists, some of KAME userland programs has restrictions on
the use of IPv4 mapped addresses:
- rshd/rlogind do not accept connections from IPv4 mapped address.
This is to avoid malicious use of IPv4 mapped address in IPv6 native
packet, to bypass source-address based authentication.
- ftp/ftpd assume that you are on dual stack network. IPv4 mapped address
will be decoded in userland, and will be passed to AF_INET sockets
(in other words, ftp/ftpd do not support SIIT environment).
1.12.7 Interaction with SIIT translator
SIIT translator is specified in RFC2765. KAME node cannot become a SIIT
translator box, nor SIIT end node (a node in SIIT cloud).
To become a SIIT translator box, we need to put additional code for that.
We do not have the code in our tree at this moment.
There are multiple reasons that we are unable to become SIIT end node.
(1) SIIT translators require end nodes in the SIIT cloud to be IPv6-only.
Since we are unable to compile INET-less kernel, we are unable to become
SIIT end node. (2) As presented in 1.12.6, some of our userland code assumes
dual stack network. (3) KAME stack filters out IPv6 packets with IPv4
mapped address in the header, to secure non-SIIT case (which is much more
common). Effectively KAME node will reject any packets via SIIT translator
box. See section 1.14 for more detail about the last item.
There are documentation issues too - SIIT document requires very strange
things. For example, SIIT document asks IPv6-only (meaning no IPv4 code)
node to be able to construct IPv4 IPsec headers. If a node knows how to
construct IPv4 IPsec headers, that is not an IPv6-only node, it is a dual-stack
node. The requirements imposed in SIIT document contradict with the other
part of the document itself.
1.13 sockaddr_storage
When RFC2553 was about to be finalized, there was discussion on how struct
sockaddr_storage members are named. One proposal is to prepend "__" to the
members (like "__ss_len") as they should not be touched. The other proposal
was that don't prepend it (like "ss_len") as we need to touch those members
directly. There was no clear consensus on it.
As a result, RFC2553 defines struct sockaddr_storage as follows:
struct sockaddr_storage {
u_char __ss_len; /* address length */
u_char __ss_family; /* address family */
/* and bunch of padding */
};
On the contrary, XNET draft defines as follows:
struct sockaddr_storage {
u_char ss_len; /* address length */
u_char ss_family; /* address family */
/* and bunch of padding */
};
In December 1999, it was agreed that RFC2553bis should pick the latter (XNET)
definition.
KAME kit prior to December 1999 used RFC2553 definition. KAME kit after
December 1999 (including December) will conform to XNET definition,
based on RFC2553bis discussion.
If you look at multiple IPv6 implementations, you will be able to see
both definitions. As an userland programmer, the most portable way of
dealing with it is to:
(1) ensure ss_family and/or ss_len are available on the platform, by using
GNU autoconf,
(2) have -Dss_family=__ss_family to unify all occurences (including header
file) into __ss_family, or
(3) never touch __ss_family. cast to sockaddr * and use sa_family like:
struct sockaddr_storage ss;
family = ((struct sockaddr *)&ss)->sa_family
1.14 Invalid addresses on the wire
Some of IPv6 transition technologies embed IPv4 address into IPv6 address.
These specifications themselves are fine, however, there can be certain
set of attacks enabled by these specifications. Recent speicifcation
documents covers up those issues, however, there are already-published RFCs
that does not have protection against those (like using source address of
::ffff:127.0.0.1 to bypass "reject packet from remote" filter).
To name a few, these address ranges can be used to hose an IPv6 implementation,
or bypass security controls:
- IPv4 mapped address that embeds unspecified/multicast/loopback/broadcast
IPv4 address (if they are in IPv6 native packet header, they are malicious)
::ffff:0.0.0.0/104 ::ffff:127.0.0.0/104
::ffff:224.0.0.0/100 ::ffff:255.0.0.0/104
- 6to4 (RFC3056) prefix generated from unspecified/multicast/loopback/
broadcast/private IPv4 address
2002:0000::/24 2002:7f00::/24 2002:e000::/24
2002:ff00::/24 2002:0a00::/24 2002:ac10::/28
2002:c0a8::/32
- IPv4 compatible address that embeds unspecified/multicast/loopback/broadcast
IPv4 address (if they are in IPv6 native packet header, they are malicious).
Note that, since KAME doe snot support RFC1933/2893 auto tunnels, KAME nodes
are not vulnerable to these packets.
::0.0.0.0/104 ::127.0.0.0/104 ::224.0.0.0/100 ::255.0.0.0/104
Also, since KAME does not support RFC1933/2893 auto tunnels, seeing IPv4
compatible is very rare. You should take caution if you see those on the wire.
If we see IPv6 packets with IPv4 mapped address (::ffff:0.0.0.0/96) in the
header in dual-stack environment (not in SIIT environment), they indicate
that someone is trying to inpersonate IPv4 peer. The packet should be dropped.
IPv6 specifications do not talk very much about IPv6 unspecified address (::)
in the IPv6 source address field. Clarification is in progress.
Here are couple of comments:
- IPv6 unspecified address can be used in IPv6 source address field, if and
only if we have no legal source address for the node. The legal situations
include, but may not be limited to, (1) MLD while no IPv6 address is assigned
to the node and (2) DAD.
- If IPv6 TCP packet has IPv6 unspecified address, it is an attack attempt.
The form can be used as a trigger for TCP DoS attack. KAME code already
filters them out.
- The following examples are seemingly illegal. It seems that there's general
consensus among ipngwg for those. (1) mobile-ip6 home address option,
(2) offlink packets (so routers should not forward them).
KAME implmements (2) already.
KAME code is carefully written to avoid such incidents. More specifically,
KAME kernel will reject packets with certain source/dstination address in IPv6
base header, or IPv6 routing header. Also, KAME default configuration file
is written carefully, to avoid those attacks.
draft-itojun-ipv6-transition-abuse-01.txt talks about more about this.
1.15 Node's required addresses
RFC2373 section 2.8 talks about required addresses for an IPv6
node. The section talks about how KAME stack manages those required
addresses.
1.15.1 Host case
The following items are automatically assigned to the node (or the node will
automatically joins the group), at bootstrap time:
- Loopback address
- All-nodes multicast addresses (ff01::1)
The following items will be automatically handled when the interface becomes
IFF_UP:
- Its link-local address for each interface
- Solicited-node multicast address for link-local addresses
- Link-local allnodes multicast address (ff02::1)
The following items need to be configured manually by ifconfig(8) or prefix(8).
Alternatively, these can be autoconfigured by using stateless address
autoconfiguration.
- Assigned unicast/anycast addresses
- Solicited-Node multicast address for assigned unicast address
Users can join groups by using appropriate system calls like setsockopt(2).
1.15.2 Router case
In addition to the above, routers needs to handle the following items.
The following items need to be configured manually by using ifconfig(8).
o The subnet-router anycast addresses for the interfaces it is configured
to act as a router on (prefix::/64)
o All other anycast addresses with which the router has been configured
The router will join the following multicast group when rtadvd(8) is available
for the interface.
o All-Routers Multicast Addresses (ff02::2)
Routing daemons will join appropriate multicast groups, as necessary,
like ff02::9 for RIPng.
Users can join groups by using appropriate system calls like setsockopt(2).
1.16 Advanced API
Current KAME kernel implements 2292bis API, documented in
draft-ietf-ipngwg-rfc2292bis-xx.txt. It also implements RFC2292 API,
for backward compatibility purposes with *BSD-integrated codebase.
KAME tree ships with 2292bis headers.
*BSD-integrated codebase implements either RFC2292, or 2292bis, API.
see "COVERAGE" document for detailed implementation status.
Here are couple of issues to mention:
- *BSD-integrated binaries, compiled for RFC2292, will work on KAME kernel.
For example, OpenBSD 2.7 /sbin/rtsol will work on KAME/openbsd kernel.
- KAME binaries, compiled using 2292bis, will not work on *BSD-integrated
kenrel. For example, KAME /usr/local/v6/sbin/rtsol will not work on
OpenBSD 2.7 kernel.
- 2292bis API is not compatible with RFC2292 API. 2292bis #define symbols
conflict with RFC2292 symbols. Therefore, if you compile programs that
assume RFC2292 API, the compilation itself goes fine, however, the compiled
binary will not work correctly. The problem is not KAME issue, but API
issue. For example, Solaris 8 implements 2292bis API. If you compile
RFC2292-based code on Solaris 8, the binary can behave strange.
There are few (or couple of) incompatible behavior in RFC2292 binary backward
compatibility support in KAME tree. To enumerate:
- Type 0 routing header lacks support for strict/loose bitmap.
Even if we see packets with "strict" bit set, those bits will not be made
visible to the userland.
Background: RFC2292 document is based on RFC1883 IPv6, and it uses
strict/loose bitmap. 2292bis document is based on RFC2460 IPv6, and it has
no strict/loose bitmap (it was removed from RFC2460). KAME tree obeys
RFC2460 IPv6, and lacks support for strict/loose bitmap.
2. Network Drivers
KAME requires three items to be added into the standard drivers:
(1) mbuf clustering requirement. In this stable release, we changed
MINCLSIZE into MHLEN+1 for all the operating systems in order to make
all the drivers behave as we expect.
(2) multicast. If "ifmcstat" yields no multicast group for a
interface, that interface has to be patched.
To avoid troubles, we suggest you to comment out the device drivers
for unsupported/unnecessary cards, from the kernel configuration file.
If you accidentally enable unsupported drivers, some of the userland
tools may not work correctly (routing daemons are typical example).
In the following sections, "official support" means that KAME developers
are using that ethernet card/driver frequently.
(NOTE: In the past we required all pcmcia drivers to have a call to
in6_ifattach(). We have no such requirement any more)
2.1 FreeBSD 2.2.x-RELEASE
Here is a list of FreeBSD 2.2.x-RELEASE drivers and its conditions:
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
ar looks ok - -
cnw ok ok yes (*)
ed ok ok yes
ep ok ok yes
fe ok ok yes
sn looks ok - - (*)
vx looks ok - -
wlp ok ok - (*)
xl ok ok yes
zp ok ok -
(FDDI)
fpa looks ok ? -
(ATM)
en ok ok yes
(Serial)
lp ? - not work
sl ? - not work
sr looks ok ok - (**)
You may want to add an invocation of "rtsol" in "/etc/pccard_ether",
if you are using notebook computers and PCMCIA ethernet card.
(*) These drivers are distributed with PAO (http://www.jp.freebsd.org/PAO/).
(**) There was some report says that, if you make sr driver up and down and
then up, the kernel may hang up. We have disabled frame-relay support from
sr driver and after that this looks to be working fine. If you need
frame-relay support to come back, please contact KAME developers.
2.2 BSD/OS 3.x
The following lists BSD/OS 3.x device drivers and its conditions:
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
cnw ok ok yes
de ok ok -
df ok ok -
eb ok ok -
ef ok ok yes
exp ok ok -
mz ok ok yes
ne ok ok yes
we ok ok -
(FDDI)
fpa ok ok -
(ATM)
en maybe ok -
(Serial)
ntwo ok ok yes
sl ? - not work
appp ? - not work
You may want to use "@insert" directive in /etc/pccard.conf to invoke
"rtsol" command right after dynamic insertion of PCMCIA ethernet cards.
2.3 NetBSD
The following table lists the network drivers we have tried so far.
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
awi pcmcia/i386 ok ok -
bah zbus/amiga NG(*)
cnw pcmcia/i386 ok ok yes
ep pcmcia/i386 ok ok -
le sbus/sparc ok ok yes
ne pci/i386 ok ok yes
ne pcmcia/i386 ok ok yes
wi pcmcia/i386 ok ok yes
(ATM)
en pci/i386 ok ok -
(*) This may need some fix, but I'm not sure what arcnet interfaces assume...
2.4 FreeBSD 3.x-RELEASE
Here is a list of FreeBSD 3.x-RELEASE drivers and its conditions:
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
cnw ok ok -(*)
ed ? ok -
ep ok ok -
fe ok ok yes
fxp ?(**)
lnc ? ok -
sn ? ? -(*)
wi ok ok yes
xl ? ok -
(*) These drivers are distributed with PAO as PAO3
(http://www.jp.freebsd.org/PAO/).
(**) there are trouble reports with multicast filter initialization.
More drivers will just simply work on KAME FreeBSD 3.x-RELEASE but have not
been checked yet.
2.5 FreeBSD 4.x-RELEASE
Here is a list of FreeBSD 4.x-RELEASE drivers and its conditions:
driver multicast
--- ---
(Ethernet)
lnc/vmware ok
2.6 OpenBSD 2.x
Here is a list of OpenBSD 2.x drivers and its conditions:
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
de pci/i386 ok ok yes
fxp pci/i386 ?(*)
le sbus/sparc ok ok yes
ne pci/i386 ok ok yes
ne pcmcia/i386 ok ok yes
wi pcmcia/i386 ok ok yes
(*) There seem to be some problem in driver, with multicast filter
configuration. This happens with certain revision of chipset on the card.
Should be fixed by now by workaround in sys/net/if.c, but still not sure.
2.7 BSD/OS 4.x
The following lists BSD/OS 4.x device drivers and its conditions:
driver mbuf(1) multicast(2) official support?
--- --- --- ---
(Ethernet)
de ok ok yes
exp (*)
You may want to use "@insert" directive in /etc/pccard.conf to invoke
"rtsol" command right after dynamic insertion of PCMCIA ethernet cards.
(*) exp driver has serious conflict with KAME initialization sequence.
A workaround is committed into sys/i386/pci/if_exp.c, and should be okay by now.
3. Translator
We categorize IPv4/IPv6 translator into 4 types.
Translator A --- It is used in the early stage of transition to make
it possible to establish a connection from an IPv6 host in an IPv6
island to an IPv4 host in the IPv4 ocean.
Translator B --- It is used in the early stage of transition to make
it possible to establish a connection from an IPv4 host in the IPv4
ocean to an IPv6 host in an IPv6 island.
Translator C --- It is used in the late stage of transition to make it
possible to establish a connection from an IPv4 host in an IPv4 island
to an IPv6 host in the IPv6 ocean.
Translator D --- It is used in the late stage of transition to make it
possible to establish a connection from an IPv6 host in the IPv6 ocean
to an IPv4 host in an IPv4 island.
KAME provides an TCP relay translator for category A. This is called
"FAITH". We also provide IP header translator for category A.
3.1 FAITH TCP relay translator
FAITH system uses TCP relay daemon called "faithd" helped by the KAME kernel.
FAITH will reserve an IPv6 address prefix, and relay TCP connection
toward that prefix to IPv4 destination.
For example, if the reserved IPv6 prefix is 3ffe:0501:0200:ffff::, and
the IPv6 destination for TCP connection is 3ffe:0501:0200:ffff::163.221.202.12,
the connection will be relayed toward IPv4 destination 163.221.202.12.
destination IPv4 node (163.221.202.12)
^
| IPv4 tcp toward 163.221.202.12
FAITH-relay dual stack node
^
| IPv6 TCP toward 3ffe:0501:0200:ffff::163.221.202.12
source IPv6 node
faithd must be invoked on FAITH-relay dual stack node.
For more details, consult kame/kame/faithd/README and
draft-ietf-ngtrans-tcpudp-relay-04.txt.
3.2 IPv6-to-IPv4 header translator
(to be written)
4. IPsec
IPsec is implemented as the following three components.
(1) Policy Management
(2) Key Management
(3) AH, ESP and IPComp handling in kernel
Note that KAME/OpenBSD does NOT include support for KAME IPsec code,
as OpenBSD team has their home-brew IPsec stack and they have no plan
to replace it. IPv6 support for IPsec is, therefore, lacking on KAME/OpenBSD.
http://www.netbsd.org/Documentation/network/ipsec/ has more information
including usage examples.
4.1 Policy Management
The kernel implements experimental policy management code. There are two way
to manage security policy. One is to configure per-socket policy using
setsockopt(3). In this cases, policy configuration is described in
ipsec_set_policy(3). The other is to configure kernel packet filter-based
policy using PF_KEY interface, via setkey(8).
The policy entry will be matched in order. The order of entries makes
difference in behavior.
4.2 Key Management
The key management code implemented in this kit (sys/netkey) is a
home-brew PFKEY v2 implementation. This conforms to RFC2367.
The home-brew IKE daemon, "racoon" is included in the kit (kame/kame/racoon,
or usr.sbin/racoon).
Basically you'll need to run racoon as daemon, then setup a policy
to require keys (like ping -P 'out ipsec esp/transport//use').
The kernel will contact racoon daemon as necessary to exchange keys.
In IKE spec, there's ambiguity about interpretation of "tunnel" proposal.
For example, if we would like to propose the use of following packet:
IP AH ESP IP payload
some implementation proposes it as "AH transport and ESP tunnel", since
this is more logical from packet construction point of view. Some
implementation proposes it as "AH tunnel and ESP tunnel".
Racoon follows the former route.
This raises real interoperability issue. We hope this to be resolved quickly.
4.3 AH and ESP handling
IPsec module is implemented as "hooks" to the standard IPv4/IPv6
processing. When sending a packet, ip{,6}_output() checks if ESP/AH
processing is required by checking if a matching SPD (Security
Policy Database) is found. If ESP/AH is needed,
{esp,ah}{4,6}_output() will be called and mbuf will be updated
accordingly. When a packet is received, {esp,ah}4_input() will be
called based on protocol number, i.e. (*inetsw[proto])().
{esp,ah}4_input() will decrypt/check authenticity of the packet,
and strips off daisy-chained header and padding for ESP/AH. It is
safe to strip off the ESP/AH header on packet reception, since we
will never use the received packet in "as is" form.
By using ESP/AH, TCP4/6 effective data segment size will be affected by
extra daisy-chained headers inserted by ESP/AH. Our code takes care of
the case.
Basic crypto functions can be found in directory "sys/crypto". ESP/AH
transform are listed in {esp,ah}_core.c with wrapper functions. If you
wish to add some algorithm, add wrapper function in {esp,ah}_core.c, and
add your crypto algorithm code into sys/crypto.
Tunnel mode works basically fine, but comes with the following restrictions:
- You cannot run routing daemon across IPsec tunnel, since we do not model
IPsec tunnel as pseudo interfaces.
- Authentication model for AH tunnel must be revisited. We'll need to
improve the policy management engine, eventually.
- Path MTU discovery does not work across IPv6 IPsec tunnel gateway due to
insufficient code.
AH specificaton does not talk much about "multiple AH on a packet" case.
We incrementally compute AH checksum, from inside to outside. Also, we
treat inner AH to be immutable.
For example, if we are to create the following packet:
IP AH1 AH2 AH3 payload
we do it incrementally. As a result, we get crypto checksums like below:
AH3 has checksum against "IP AH3' payload".
where AH3' = AH3 with checksum field filled with 0.
AH2 has checksum against "IP AH2' AH3 payload".
AH1 has checksum against "IP AH1' AH2 AH3 payload",
Also note that AH3 has the smallest sequence number, and AH1 has the largest
sequence number.
To avoid traffic analysis on shorter packets, ESP output logic supports
random length padding. By setting net.inet.ipsec.esp_randpad (or
net.inet6.ipsec6.esp_randpad) to positive value N, you can ask the kernel
to randomly pad packets shorter than N bytes, to random length smaller than
or equal to N. Note that N does not include ESP authentication data length.
Also note that the random padding is not included in TCP segment
size computation. Negative value will turn off the functionality.
Recommeded value for N is like 128, or 256. If you use a too big number
as N, you may experience inefficiency due to fragmented packtes.
4.4 IPComp handling
IPComp stands for IP payload compression protocol. This is aimed for
payload compression, not the header compression like PPP VJ compression.
This may be useful when you are using slow serial link (say, cell phone)
with powerful CPU (well, recent notebook PCs are really powerful...).
The protocol design of IPComp is very similar to IPsec, though it was
defined separately from IPsec itself.
Here are some points to be noted:
- IPComp is treated as part of IPsec protocol suite, and SPI and
CPI space is unified. Spec says that there's no relationship
between two so they are assumed to be separate in specs.
- IPComp association (IPCA) is kept in SAD.
- It is possible to use well-known CPI (CPI=2 for DEFLATE for example),
for outbound/inbound packet, but for indexing purposes one element from
SPI/CPI space will be occupied anyway.
- pfkey is modified to support IPComp. However, there's no official
SA type number assignment yet. Portability with other IPComp
stack is questionable (anyway, who else implement IPComp on UN*X?).
- Spec says that IPComp output processing must be performed before AH/ESP
output processing, to achieve better compression ratio and "stir" data
stream before encryption. The most meaningful processing order is:
(1) compress payload by IPComp, (2) encrypt payload by ESP, then (3) attach
authentication data by AH.
However, with manual SPD setting, you are able to violate the ordering
(KAME code is too generic, maybe). Also, it is just okay to use IPComp
alone, without AH/ESP.
- Though the packet size can be significantly decreased by using IPComp, no
special consideration is made about path MTU (spec talks nothing about MTU
consideration). IPComp is designed for serial links, not ethernet-like
medium, it seems.
- You can change compression ratio on outbound packet, by changing
deflate_policy in sys/netinet6/ipcomp_core.c. You can also change outbound
history buffer size by changing deflate_window_out in the same source code.
(should it be sysctl accessible, or per-SAD configurable?)
- Tunnel mode IPComp is not working right. KAME box can generate tunnelled
IPComp packet, however, cannot accept tunneled IPComp packet.
- You can negotiate IPComp association with racoon IKE daemon.
- KAME code does not attach Adler32 checksum to compressed data.
see ipsec wg mailing list discussion in Jan 2000 for details.
4.5 Conformance to RFCs and IDs
The IPsec code in the kernel conforms (or, tries to conform) to the
following standards:
"old IPsec" specification documented in rfc182[5-9].txt
"new IPsec" specification documented in:
rfc240[1-6].txt rfc241[01].txt rfc2451.txt
draft-mcdonald-simple-ipsec-api-01.txt
(expired, available in ftp://ftp.kame.net/pub/internet-drafts/)
draft-ietf-ipsec-ciph-aes-cbc-00.txt
IPComp:
RFC2393: IP Payload Compression Protocol (IPComp)
IKE specifications (rfc240[7-9].txt) are implemented in userland
as "racoon" IKE daemon.
Currently supported algorithms are:
old IPsec AH
null crypto checksum (no document, just for debugging)
keyed MD5 with 128bit crypto checksum (rfc1828.txt)
keyed SHA1 with 128bit crypto checksum (no document)
HMAC MD5 with 128bit crypto checksum (rfc2085.txt)
HMAC SHA1 with 128bit crypto checksum (no document)
old IPsec ESP
null encryption (no document, similar to rfc2410.txt)
DES-CBC mode (rfc1829.txt)
new IPsec AH
null crypto checksum (no document, just for debugging)
keyed MD5 with 96bit crypto checksum (no document)
keyed SHA1 with 96bit crypto checksum (no document)
HMAC MD5 with 96bit crypto checksum (rfc2403.txt
HMAC SHA1 with 96bit crypto checksum (rfc2404.txt)
HMAC SHA2-256 with 96bit crypto checksum (no document)
HMAC SHA2-384 with 96bit crypto checksum (no document)
HMAC SHA2-512 with 96bit crypto checksum (no document)
new IPsec ESP
null encryption (rfc2410.txt)
DES-CBC with derived IV
(draft-ietf-ipsec-ciph-des-derived-01.txt, draft expired)
DES-CBC with explicit IV (rfc2405.txt)
3DES-CBC with explicit IV (rfc2451.txt)
BLOWFISH CBC (rfc2451.txt)
CAST128 CBC (rfc2451.txt)
RIJNDAEL/AES CBC (draft-ietf-ipsec-ciph-aes-cbc-00.txt,
uses IANA-assigned protocol number)
TWOFISH CBC (draft-ietf-ipsec-ciph-aes-cbc-00.txt)
each of the above can be combined with:
ESP authentication with HMAC-MD5(96bit)
ESP authentication with HMAC-SHA1(96bit)
IPComp
RFC2394: IP Payload Compression Using DEFLATE
The following algorithms are NOT supported:
old IPsec AH
HMAC MD5 with 128bit crypto checksum + 64bit replay prevention
(rfc2085.txt)
keyed SHA1 with 160bit crypto checksum + 32bit padding (rfc1852.txt)
The key/policy management API is based on the following document, with fair
amount of extensions:
RFC2367: PF_KEY key management API
4.6 ECN consideration on IPsec tunnels
KAME IPsec implements ECN-friendly IPsec tunnel, described in
draft-ietf-ipsec-ecn-02.txt.
Normal IPsec tunnel is described in RFC2401. On encapsulation,
IPv4 TOS field (or, IPv6 traffic class field) will be copied from inner
IP header to outer IP header. On decapsulation outer IP header
will be simply dropped. The decapsulation rule is not compatible
with ECN, since ECN bit on the outer IP TOS/traffic class field will be
lost.
To make IPsec tunnel ECN-friendly, we should modify encapsulation
and decapsulation procedure. This is described in
draft-ietf-ipsec-ecn-02.txt, chapter 3.3.
KAME IPsec tunnel implementation can give you three behaviors, by setting
net.inet.ipsec.ecn (or net.inet6.ipsec6.ecn) to some value:
- RFC2401: no consideration for ECN (sysctl value -1)
- ECN forbidden (sysctl value 0)
- ECN allowed (sysctl value 1)
Note that the behavior is configurable in per-node manner, not per-SA manner
(draft-ietf-ipsec-ecn-02 wants per-SA configuration, but it looks too much
for me).
The behavior is summarized as follows (see source code for more detail):
encapsulate decapsulate
--- ---
RFC2401 copy all TOS bits drop TOS bits on outer
from inner to outer. (use inner TOS bits as is)
ECN forbidden copy TOS bits except for ECN drop TOS bits on outer
(masked with 0xfc) from inner (use inner TOS bits as is)
to outer. set ECN bits to 0.
ECN allowed copy TOS bits except for ECN use inner TOS bits with some
CE (masked with 0xfe) from change. if outer ECN CE bit
inner to outer. is 1, enable ECN CE bit on
set ECN CE bit to 0. the inner.
General strategy for configuration is as follows:
- if both IPsec tunnel endpoint are capable of ECN-friendly behavior,
you'd better configure both end to "ECN allowed" (sysctl value 1).
- if the other end is very strict about TOS bit, use "RFC2401"
(sysctl value -1).
- in other cases, use "ECN forbidden" (sysctl value 0).
The default behavior is "ECN forbidden" (sysctl value 0).
For more information, please refer to:
draft-ietf-ipsec-ecn-02.txt
RFC2481 (Explicit Congestion Notification)
KAME sys/netinet6/{ah,esp}_input.c
(Thanks goes to Kenjiro Cho <kjc@csl.sony.co.jp> for detailed analysis)
4.7 Interoperability
IPsec, IPComp (in kernel) and IKE (in userland as "racoon") has been tested
at several interoperability test events, and it is known to interoperate
with many other implementations well. Also, KAME IPsec has quite wide
coverage for IPsec crypto algorithms documented in RFC (we do not cover
algorithms with intellectual property issues, though).
Here are (some of) platforms we have tested IPsec/IKE interoperability
in the past, no particular order. Note that both ends (KAME and
others) may have modified their implementation, so use the following
list just for reference purposes.
ACC, allied-telesis, Altiga, Ashley-laurent (vpcom.com), BlueSteel,
CISCO IOS, Cryptek, Checkpoint FW-1, Data Fellows (F-Secure),
Ericsson, Fitel, FreeS/WAN, HiFn, HITACHI, IBM AIX, IIJ, Intel Canada,
Intel Packet Protect, MEW NetCocoon, MGCS, Microsoft WinNT/2000,
NAI PGPnet, NetLock, NIST (linux IPsec + plutoplus), NEC IX5000,
Netscreen, NxNetworks, OpenBSD isakmpd, Pivotal, Radguard, RapidStream,
RedCreek, Routerware, RSA, SSH (both IPv4/IPv6), Secure Computing,
Soliton, Sun Solaris8, TIS/NAI Gauntret, Toshiba, VPNet,
Yamaha RT series
Here are (some of) platforms we have tested IPComp/IKE interoperability
in the past, in no particular order.
IRE, SSH (both IPv4/IPv6), NetLock
VPNC (vpnc.org) provides IPsec conformance tests, using KAME and OpenBSD
IPsec/IKE implementations. Their test results are available at
http://www.vpnc.org/conformance.html, and it may give you more idea
about which implementation interoperates with KAME IPsec/IKE implementation.
5. ALTQ
KAME kit includes ALTQ 2.1 code, which supports FreeBSD2, FreeBSD3,
NetBSD and OpenBSD. For BSD/OS, ALTQ does not work.
ALTQ in KAME supports (or tries to support) IPv6.
(actually, ALTQ is developed on KAME repository since ALTQ 2.1 - Jan 2000)
ALTQ occupies single character device number. For FreeBSD, it is officially
allocated. For OpenBSD and NetBSD, we use the number which is not
currently allocated (will eventually get an official number).
The character device is enabled for i386 architecture only. To enable and
compile ALTQ-ready kernel for other archititectures, take the following steps:
- assume that your architecture is FOOBAA.
- modify sys/arch/FOOBAA/FOOBAA/conf.c (or somewhere that defines cdevsw),
to include a line for ALTQ. look at sys/arch/i386/i386/conf.c for
example. The major number must be same as i386 case.
- copy kernel configuration file (like ALTQ.v6 or GENERIC.v6) from i386,
and modify accordingly.
- build a kernel.
- before building userland, change netbsd/{lib,usr.sbin,usr.bin}/Makefile
(or openbsd/foobaa) so that it will visit altq-related sub directories.
6. mobile-ip6
6.1 KAME node as correspondent node
Default installation recognizes home address option (in destination
options header). No sub-options are supported. interaction with
IPsec, and/or 2292bis API, needs further study.
6.2 KAME node as home agent/mobile node
KAME kit includes Ericsson mobile-ip6 code. The integration is just started
(in Feb 2000), and we will need some more time to integrate it better.
See kame/mip6config/{QUICKSTART,README_MIP6.txt} for more details.
The Ericsson code implements revision 09 of the mobile-ip6 draft. There
are other implementations available:
NEC: http://www.6bone.nec.co.jp/mipv6/internal-dist/ (-13 draft)
SFC: http://neo.sfc.wide.ad.jp/~mip6/ (-13 draft)
7. Coding style
The KAME developers basically do not make a bother about coding
style. However, there is still some agreement on the style, in order
to make the distributed develoment smooth.
- the tab character should be 8 columns wide (tabstops are at 8, 16, 24, ...
column). With vi, use ":set ts=8 sw=8".
- each line should be within 80 characters.
- keep a single open/close bracket in a comment such as in the following
line:
putchar('('); /* ) */
without this, some vi users would have a hard time to match a pair of
brackets. Although this type of bracket seems clumsy and is even
harmful for some other type of vi users and Emacs users, the
agreement in the KAME developers is to allow it.
- add the following line to the head of every KAME-derived file:
/* (dollar)KAME(dollar) */
where "(dollar)" is the dollar character ($), and around "$" are tabs.
(this is for C. For other language, you should use its own comment
line.)
Once commited to the CVS repository, this line will contain its
version number (see, for example, at the top of this file). This
would make it easy to report a bug.
- when creating a new file with the WIDE copyright, tap "make copyright.c" at
the top-level, and use copyright.c as a template. KAME RCS tag will be
included automatically.
- when editting a third-party package, keep its own coding style as
much as possible, even if the style does not follow the items above.
When you want to contribute something to the KAME project, and if *you
do not mind* the agreement, it would be helpful for the project to
keep these rules. Note, however, that we would never intend to force
you to adopt our rules. We would rather regard your own style,
especially when you have a policy about the style.
<end of IMPLEMENTATION>
Reference in New Issue View Git Blame Copy Permalink