232 lines
5.9 KiB
Plaintext
232 lines
5.9 KiB
Plaintext
# $FreeBSD$
|
|
|
|
# MAC/ART ? - they're 00:02:03:04:05:06 :(
|
|
|
|
# ath0 chain0 EXTERNAL_LNA0: 18
|
|
# ath0 chain1 EXTERNAL_LNA1: 19
|
|
# These are configured as GPIO output, init low, then
|
|
# set the GPIO 'type' AR934X_GPIO_OUT_EXT_LNA0/AR934X_GPIO_OUT_EXT_LNA1.
|
|
|
|
# XXX There's no arge1 on this!
|
|
|
|
# XXX RFKILL?
|
|
|
|
# mdiobus0 on arge0
|
|
hint.argemdio.0.at="nexus0"
|
|
hint.argemdio.0.maddr=0x19000000
|
|
hint.argemdio.0.msize=0x1000
|
|
hint.argemdio.0.order=0
|
|
|
|
# DB120 GMAC configuration
|
|
# + AR934X_ETH_CFG_RGMII_GMAC0 (1 << 0)
|
|
hint.ar934x_gmac.0.gmac_cfg=0x1
|
|
|
|
# Board mac address is at 0x1f01fc00.
|
|
# ath0: offset 0
|
|
# ath1: offset -1
|
|
# arge0: offset -2
|
|
# arge1: not hooked up; doesn't matter
|
|
hint.ar71xx.0.eeprom_mac_addr=0x1f01fc00
|
|
hint.ar71xx.0.eeprom_mac_isascii=0
|
|
|
|
hint.ar71xx_mac_map.0.devid=ath
|
|
hint.ar71xx_mac_map.0.unitid=0
|
|
hint.ar71xx_mac_map.0.offset=0
|
|
hint.ar71xx_mac_map.0.is_local=0
|
|
|
|
hint.ar71xx_mac_map.1.devid=ath
|
|
hint.ar71xx_mac_map.1.unitid=1
|
|
hint.ar71xx_mac_map.1.offset=-1
|
|
hint.ar71xx_mac_map.1.is_local=0
|
|
|
|
hint.ar71xx_mac_map.2.devid=arge
|
|
hint.ar71xx_mac_map.2.unitid=0
|
|
hint.ar71xx_mac_map.2.offset=-2
|
|
hint.ar71xx_mac_map.2.is_local=0
|
|
|
|
# GMAC0 here - connected to an AR8327
|
|
hint.arswitch.0.at="mdio0"
|
|
hint.arswitch.0.is_7240=0
|
|
hint.arswitch.0.is_9340=0 # not the internal switch!
|
|
hint.arswitch.0.numphys=5
|
|
hint.arswitch.0.phy4cpu=0
|
|
hint.arswitch.0.is_rgmii=0
|
|
hint.arswitch.0.is_gmii=0
|
|
|
|
# Other AR8327 configuration parameters
|
|
|
|
# AR8327_PAD_MAC_RGMII
|
|
hint.arswitch.0.pad.0.mode=6
|
|
hint.arswitch.0.pad.0.txclk_delay_en=1
|
|
hint.arswitch.0.pad.0.rxclk_delay_en=1
|
|
# AR8327_CLK_DELAY_SEL1
|
|
hint.arswitch.0.pad.0.txclk_delay_sel=1
|
|
# AR8327_CLK_DELAY_SEL2
|
|
hint.arswitch.0.pad.0.rxclk_delay_sel=2
|
|
|
|
# XXX there's no LED management just yet!
|
|
hint.arswitch.0.led.ctrl0=0xc737c737
|
|
hint.arswitch.0.led.ctrl1=0x00000000
|
|
hint.arswitch.0.led.ctrl2=0x00000000
|
|
hint.arswitch.0.led.ctrl3=0x0030c300
|
|
hint.arswitch.0.led.open_drain=0
|
|
|
|
# force_link=1 is required for the rest of the parameters
|
|
# to be configured.
|
|
hint.arswitch.0.port.0.force_link=1
|
|
hint.arswitch.0.port.0.speed=1000
|
|
hint.arswitch.0.port.0.duplex=1
|
|
hint.arswitch.0.port.0.txpause=1
|
|
hint.arswitch.0.port.0.rxpause=1
|
|
|
|
# XXX OpenWRT DB120 BSP doesn't have media/duplex set?
|
|
hint.arge.0.phymask=0x0
|
|
hint.arge.0.media=1000
|
|
hint.arge.0.fduplex=1
|
|
hint.arge.0.miimode=3 # RGMII
|
|
hint.arge.0.pll_1000=0x06000000
|
|
|
|
# mdiobus1 on arge1
|
|
hint.argemdio.1.at="nexus0"
|
|
hint.argemdio.1.maddr=0x1a000000
|
|
hint.argemdio.1.msize=0x1000
|
|
hint.argemdio.1.order=0
|
|
|
|
# Embedded switch on the AR9344
|
|
# mdio1 is actually created as the AR8327 internal bus; so
|
|
# this pops up as mdio2.
|
|
#
|
|
# XXX TODO: there's no need for AR9344 internal switch; it isn't exposed
|
|
hint.arswitch.1.at="mdio2"
|
|
hint.arswitch.1.is_7240=0
|
|
hint.arswitch.1.is_9340=1
|
|
hint.arswitch.1.numphys=5
|
|
hint.arswitch.1.phy4cpu=0 # phy 4 is not a "CPU port" PHY here
|
|
hint.arswitch.1.is_rgmii=0
|
|
hint.arswitch.1.is_gmii=1 # arge1 <-> switch PHY is GMII
|
|
|
|
# arge1 - lock up to 1000/full
|
|
hint.arge.1.phymask=0x0 # Nothing attached here (XXX?)
|
|
hint.arge.1.media=1000
|
|
hint.arge.1.fduplex=1
|
|
hint.arge.1.miimode=1 # GMII
|
|
|
|
# MAC for arge1 is the second 6 bytes of the ART
|
|
# hint.arge.1.eeprommac=0x1f7f0006
|
|
|
|
# ath0: Where the ART is - last 64k in the flash
|
|
hint.ath.0.eepromaddr=0x1fff0000
|
|
hint.ath.0.eepromsize=16384
|
|
|
|
# ath1: it's different; it's a PCIe attached device, so
|
|
# we instead need to teach the PCIe bridge code about it
|
|
# (ie, the 'early pci fixup' stuff that programs the PCIe
|
|
# host registers on the NIC) and then we teach ath where
|
|
# to find it.
|
|
|
|
# ath1 hint - pcie slot 0
|
|
hint.pcib.0.bus.0.0.0.ath_fixup_addr=0x1fff4000
|
|
hint.pcib.0.bus.0.0.0.ath_fixup_size=16384
|
|
|
|
# ath0 - eeprom comes from here
|
|
hint.ath.1.eeprom_firmware="pcib.0.bus.0.0.0.eeprom_firmware"
|
|
|
|
# flash layout:
|
|
#
|
|
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART)
|
|
|
|
# 128KiB uboot
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x00020000 # 128k u-boot
|
|
hint.map.0.name="u-boot"
|
|
hint.map.0.readonly=1
|
|
|
|
# kernel
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start=0x00020000
|
|
hint.map.2.end="search:0x00020000:0x10000:.!/bin/sh"
|
|
hint.map.2.name="kernel"
|
|
hint.map.2.readonly=1
|
|
|
|
# 1344KiB uImage
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start="search:0x00020000:0x10000:.!/bin/sh"
|
|
hint.map.3.end=0x007d0000
|
|
hint.map.3.name="rootfs"
|
|
hint.map.3.readonly=1
|
|
|
|
# 64KiB cfg
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x007d0000
|
|
hint.map.4.end=0x007e0000
|
|
hint.map.4.name="cfg"
|
|
hint.map.4.readonly=0
|
|
|
|
# 64KiB mib0
|
|
hint.map.5.at="flash/spi0"
|
|
hint.map.5.start=0x007e0000
|
|
hint.map.5.end=0x007f0000 # 64k mib0
|
|
hint.map.5.name="mib0"
|
|
hint.map.5.readonly=1
|
|
|
|
# 64KiB ART
|
|
hint.map.6.at="flash/spi0"
|
|
hint.map.6.start=0x007f0000
|
|
hint.map.6.end=0x00800000 # 64k ART
|
|
hint.map.6.name="ART"
|
|
hint.map.6.readonly=1
|
|
|
|
# GPIO configuration
|
|
# GPIO21 and GPIO22 - USB1 and USB2 power
|
|
# ath0 chain0 EXTERNAL_LNA0: 18, output
|
|
# ath0 chain1 EXTERNAL_LNA1: 19, output
|
|
|
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
|
hint.gpio.0.pinmask=0x0063f800
|
|
|
|
# Enable GPIO21, GPIO22 output and high - for USB power
|
|
hint.gpio.0.pinon=0x00600000
|
|
|
|
hint.gpio.0.func.18.gpiofunc=46
|
|
hint.gpio.0.func.18.gpiomode=1 # output, default low
|
|
|
|
hint.gpio.0.func.19.gpiofunc=47
|
|
hint.gpio.0.func.19.gpiomode=1 # output, default low
|
|
|
|
# LED QSS - 15
|
|
# LED SYSTEM - 14
|
|
# LED USB1 - 11
|
|
# LED USB2 - 12
|
|
# LED WLAN2G - 13
|
|
|
|
# SWITCH WPS - 16
|
|
# SWITCH RFKILL - 17
|
|
|
|
hint.gpioled.0.at="gpiobus0"
|
|
hint.gpioled.0.name="USB1"
|
|
hint.gpioled.0.pins=0x0800
|
|
hint.gpioled.0.invert=1
|
|
|
|
hint.gpioled.1.at="gpiobus0"
|
|
hint.gpioled.1.name="USB2"
|
|
hint.gpioled.1.pins=0x1000
|
|
hint.gpioled.1.invert=1
|
|
|
|
hint.gpioled.2.at="gpiobus0"
|
|
hint.gpioled.2.name="WLAN2G"
|
|
hint.gpioled.2.pins=0x2000
|
|
hint.gpioled.2.invert=1
|
|
|
|
hint.gpioled.3.at="gpiobus0"
|
|
hint.gpioled.3.name="SYSTEM"
|
|
hint.gpioled.3.pins=0x4000
|
|
hint.gpioled.3.invert=1
|
|
|
|
hint.gpioled.4.at="gpiobus0"
|
|
hint.gpioled.4.name="QSS"
|
|
hint.gpioled.4.pins=0x8000
|
|
hint.gpioled.4.invert=1
|
|
|
|
# XXX TODO: WPS/RFKILL switch
|