freebsd-nq/sys/dev/mii/mii_physubr.c
Marius Strobl efd4fc3fb3 o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control
support in mii(4):
  - Merge generic flow control advertisement (which can be enabled by
    passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
    NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
    IFM_FLOW isn't implemented as a global option via the "don't care
    mask" but instead as a media specific option this. This has the
    following advantages:
    o allows flow control advertisement with autonegotiation to be
      turned on and off via ifconfig(8) with the default typically
      being off (though MIIF_FORCEPAUSE has been added causing flow
      control to be always advertised, allowing to easily MFC this
      changes for drivers that previously used home-grown support for
      flow control that behaved that way without breaking POLA)
    o allows to deal with PHY drivers where flow control advertisement
      with manual selection doesn't work or at least isn't implemented,
      like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
      by setting MIIF_NOMANPAUSE
    o the available combinations of media options are readily available
      from the `ifconfig -m` output
  - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
    and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
    these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
  - Change IFM_ETH_MASTER from being implemented as a global option via
    the "don't care mask" to a media specific one as it actually is only
    applicable to IFM_1000_T to date.
  - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
    actually configure manually selected slave mode (like we also do in
    the PHY specific implementations).
  - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
    is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
  e1000phy(4) and ip1000phy(4) to use the generic flow control support
  instead of home-grown solutions via IFM_FLAGs. This includes changing
  these PHY drivers and smcphy(4) to no longer unconditionally advertise
  support for flow control but only if the selected media has IFM_FLOW
  set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
  i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
  set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
  and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
  the contents of the BMSR via mii_phy_add_media() instead of hardcoding
  them. The latter approach seems to have developed historically, besides
  causing unnecessary code duplication it was also undesirable because
  brgphy_mii_phy_auto() already based the capability advertisement on the
  contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
  just BCM5701. Apparently this was a misinterpretation of a workaround
  in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
  BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
  this doesn't mean we can't set these as well on other PHYs for manual
  media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
  IFM_1000_T master mode support now is generally available with all PHY
  drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
  not applicable there.

Reviewed by:	yongari (plus additional testing)
Obtained from:	NetBSD (partially), OpenBSD (partially)
MFC after:	2 weeks
2010-11-14 13:26:10 +00:00

573 lines
15 KiB
C

/* $NetBSD: mii_physubr.c,v 1.5 1999/08/03 19:41:49 drochner Exp $ */
/*-
* Copyright (c) 1998, 1999, 2000, 2001 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
/*
* Subroutines common to all PHYs.
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/errno.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include "miibus_if.h"
/*
* Media to register setting conversion table. Order matters.
*/
static const struct mii_media mii_media_table[MII_NMEDIA] = {
/* None */
{ BMCR_ISO, ANAR_CSMA,
0, },
/* 10baseT */
{ BMCR_S10, ANAR_CSMA|ANAR_10,
0, },
/* 10baseT-FDX */
{ BMCR_S10|BMCR_FDX, ANAR_CSMA|ANAR_10_FD,
0, },
/* 100baseT4 */
{ BMCR_S100, ANAR_CSMA|ANAR_T4,
0, },
/* 100baseTX */
{ BMCR_S100, ANAR_CSMA|ANAR_TX,
0, },
/* 100baseTX-FDX */
{ BMCR_S100|BMCR_FDX, ANAR_CSMA|ANAR_TX_FD,
0, },
/* 1000baseX */
{ BMCR_S1000, ANAR_CSMA,
0, },
/* 1000baseX-FDX */
{ BMCR_S1000|BMCR_FDX, ANAR_CSMA,
0, },
/* 1000baseT */
{ BMCR_S1000, ANAR_CSMA,
GTCR_ADV_1000THDX },
/* 1000baseT-FDX */
{ BMCR_S1000, ANAR_CSMA,
GTCR_ADV_1000TFDX },
};
void
mii_phy_setmedia(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
int bmcr, anar, gtcr;
if (IFM_SUBTYPE(ife->ifm_media) == IFM_AUTO) {
/*
* Force renegotiation if MIIF_DOPAUSE or MIIF_FORCEANEG.
* The former is necessary as we might switch from flow-
* control advertisment being off to on or vice versa.
*/
if ((PHY_READ(sc, MII_BMCR) & BMCR_AUTOEN) == 0 ||
(sc->mii_flags & (MIIF_DOPAUSE | MIIF_FORCEANEG)) != 0)
(void)mii_phy_auto(sc);
return;
}
/*
* Table index is stored in the media entry.
*/
KASSERT(ife->ifm_data >=0 && ife->ifm_data < MII_NMEDIA,
("invalid ife->ifm_data (0x%x) in mii_phy_setmedia",
ife->ifm_data));
anar = mii_media_table[ife->ifm_data].mm_anar;
bmcr = mii_media_table[ife->ifm_data].mm_bmcr;
gtcr = mii_media_table[ife->ifm_data].mm_gtcr;
if (IFM_SUBTYPE(ife->ifm_media) == IFM_1000_T) {
gtcr |= GTCR_MAN_MS;
if ((ife->ifm_media & IFM_ETH_MASTER) != 0)
gtcr |= GTCR_ADV_MS;
}
if ((ife->ifm_media & IFM_GMASK) == (IFM_FDX | IFM_FLOW) ||
(sc->mii_flags & MIIF_FORCEPAUSE) != 0) {
if ((sc->mii_flags & MIIF_IS_1000X) != 0)
anar |= ANAR_X_PAUSE_TOWARDS;
else {
anar |= ANAR_FC;
/* XXX Only 1000BASE-T has PAUSE_ASYM? */
if ((sc->mii_flags & MIIF_HAVE_GTCR) != 0 &&
(sc->mii_extcapabilities &
(EXTSR_1000THDX | EXTSR_1000TFDX)) != 0)
anar |= ANAR_X_PAUSE_ASYM;
}
}
if ((ife->ifm_media & IFM_LOOP) != 0)
bmcr |= BMCR_LOOP;
PHY_WRITE(sc, MII_ANAR, anar);
PHY_WRITE(sc, MII_BMCR, bmcr);
if ((sc->mii_flags & MIIF_HAVE_GTCR) != 0)
PHY_WRITE(sc, MII_100T2CR, gtcr);
}
int
mii_phy_auto(struct mii_softc *sc)
{
struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur;
int anar, gtcr;
/*
* Check for 1000BASE-X. Autonegotiation is a bit
* different on such devices.
*/
if ((sc->mii_flags & MIIF_IS_1000X) != 0) {
anar = 0;
if ((sc->mii_extcapabilities & EXTSR_1000XFDX) != 0)
anar |= ANAR_X_FD;
if ((sc->mii_extcapabilities & EXTSR_1000XHDX) != 0)
anar |= ANAR_X_HD;
if ((ife->ifm_media & IFM_FLOW) != 0 ||
(sc->mii_flags & MIIF_FORCEPAUSE) != 0)
anar |= ANAR_X_PAUSE_TOWARDS;
PHY_WRITE(sc, MII_ANAR, anar);
} else {
anar = BMSR_MEDIA_TO_ANAR(sc->mii_capabilities) |
ANAR_CSMA;
if ((ife->ifm_media & IFM_FLOW) != 0 ||
(sc->mii_flags & MIIF_FORCEPAUSE) != 0) {
if ((sc->mii_capabilities & BMSR_100TXFDX) != 0)
anar |= ANAR_FC;
/* XXX Only 1000BASE-T has PAUSE_ASYM? */
if (((sc->mii_flags & MIIF_HAVE_GTCR) != 0) &&
(sc->mii_extcapabilities &
(EXTSR_1000THDX | EXTSR_1000TFDX)) != 0)
anar |= ANAR_X_PAUSE_ASYM;
}
PHY_WRITE(sc, MII_ANAR, anar);
if ((sc->mii_flags & MIIF_HAVE_GTCR) != 0) {
gtcr = 0;
if ((sc->mii_extcapabilities & EXTSR_1000TFDX) != 0)
gtcr |= GTCR_ADV_1000TFDX;
if ((sc->mii_extcapabilities & EXTSR_1000THDX) != 0)
gtcr |= GTCR_ADV_1000THDX;
PHY_WRITE(sc, MII_100T2CR, gtcr);
}
}
PHY_WRITE(sc, MII_BMCR, BMCR_AUTOEN | BMCR_STARTNEG);
return (EJUSTRETURN);
}
int
mii_phy_tick(struct mii_softc *sc)
{
struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur;
struct ifnet *ifp = sc->mii_pdata->mii_ifp;
int reg;
/* Just bail now if the interface is down. */
if ((ifp->if_flags & IFF_UP) == 0)
return (EJUSTRETURN);
/*
* If we're not doing autonegotiation, we don't need to do
* any extra work here. However, we need to check the link
* status so we can generate an announcement if the status
* changes.
*/
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO) {
sc->mii_ticks = 0; /* reset autonegotiation timer. */
return (0);
}
/* Read the status register twice; BMSR_LINK is latch-low. */
reg = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
if ((reg & BMSR_LINK) != 0) {
sc->mii_ticks = 0; /* reset autonegotiation timer. */
/* See above. */
return (0);
}
/* Announce link loss right after it happens */
if (sc->mii_ticks++ == 0)
return (0);
/* XXX: use default value if phy driver did not set mii_anegticks */
if (sc->mii_anegticks == 0)
sc->mii_anegticks = MII_ANEGTICKS_GIGE;
/* Only retry autonegotiation every mii_anegticks ticks. */
if (sc->mii_ticks <= sc->mii_anegticks)
return (EJUSTRETURN);
sc->mii_ticks = 0;
mii_phy_reset(sc);
mii_phy_auto(sc);
return (0);
}
void
mii_phy_reset(struct mii_softc *sc)
{
struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur;
int reg, i;
if ((sc->mii_flags & MIIF_NOISOLATE) != 0)
reg = BMCR_RESET;
else
reg = BMCR_RESET | BMCR_ISO;
PHY_WRITE(sc, MII_BMCR, reg);
/* Wait 100ms for it to complete. */
for (i = 0; i < 100; i++) {
reg = PHY_READ(sc, MII_BMCR);
if ((reg & BMCR_RESET) == 0)
break;
DELAY(1000);
}
if ((sc->mii_flags & MIIF_NOISOLATE) == 0) {
if ((ife == NULL && sc->mii_inst != 0) ||
(ife != NULL && IFM_INST(ife->ifm_media) != sc->mii_inst))
PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO);
}
}
void
mii_phy_down(struct mii_softc *sc)
{
}
void
mii_phy_update(struct mii_softc *sc, int cmd)
{
struct mii_data *mii = sc->mii_pdata;
if (sc->mii_media_active != mii->mii_media_active ||
cmd == MII_MEDIACHG) {
MIIBUS_STATCHG(sc->mii_dev);
sc->mii_media_active = mii->mii_media_active;
}
if (sc->mii_media_status != mii->mii_media_status) {
MIIBUS_LINKCHG(sc->mii_dev);
sc->mii_media_status = mii->mii_media_status;
}
}
/*
* Initialize generic PHY media based on BMSR, called when a PHY is
* attached. We expect to be set up to print a comma-separated list
* of media names. Does not print a newline.
*/
void
mii_phy_add_media(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
const char *sep = "";
int fdx = 0;
if ((sc->mii_capabilities & BMSR_MEDIAMASK) == 0 &&
(sc->mii_extcapabilities & EXTSR_MEDIAMASK) == 0) {
printf("no media present");
return;
}
/*
* Set the autonegotiation timer for 10/100 media. Gigabit media is
* handled below.
*/
sc->mii_anegticks = MII_ANEGTICKS;
#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
#define PRINT(s) printf("%s%s", sep, s); sep = ", "
if ((sc->mii_flags & MIIF_NOISOLATE) == 0)
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_NONE, 0, sc->mii_inst),
MII_MEDIA_NONE);
/*
* There are different interpretations for the bits in
* HomePNA PHYs. And there is really only one media type
* that is supported.
*/
if ((sc->mii_flags & MIIF_IS_HPNA) != 0) {
if ((sc->mii_capabilities & BMSR_10THDX) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_HPNA_1, 0,
sc->mii_inst), MII_MEDIA_10_T);
PRINT("HomePNA1");
}
return;
}
if ((sc->mii_capabilities & BMSR_10THDX) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, 0, sc->mii_inst),
MII_MEDIA_10_T);
PRINT("10baseT");
}
if ((sc->mii_capabilities & BMSR_10TFDX) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T, IFM_FDX, sc->mii_inst),
MII_MEDIA_10_T_FDX);
PRINT("10baseT-FDX");
if ((sc->mii_flags & MIIF_DOPAUSE) != 0 &&
(sc->mii_flags & MIIF_NOMANPAUSE) == 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_T,
IFM_FDX | IFM_FLOW, sc->mii_inst),
MII_MEDIA_10_T_FDX);
PRINT("10baseT-FDX-flow");
}
fdx = 1;
}
if ((sc->mii_capabilities & BMSR_100TXHDX) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, 0, sc->mii_inst),
MII_MEDIA_100_TX);
PRINT("100baseTX");
}
if ((sc->mii_capabilities & BMSR_100TXFDX) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_FDX, sc->mii_inst),
MII_MEDIA_100_TX_FDX);
PRINT("100baseTX-FDX");
if ((sc->mii_flags & MIIF_DOPAUSE) != 0 &&
(sc->mii_flags & MIIF_NOMANPAUSE) == 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX,
IFM_FDX | IFM_FLOW, sc->mii_inst),
MII_MEDIA_100_TX_FDX);
PRINT("100baseTX-FDX-flow");
}
fdx = 1;
}
if ((sc->mii_capabilities & BMSR_100T4) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_T4, 0, sc->mii_inst),
MII_MEDIA_100_T4);
PRINT("100baseT4");
}
if ((sc->mii_extcapabilities & EXTSR_MEDIAMASK) != 0) {
/*
* XXX Right now only handle 1000SX and 1000TX. Need
* XXX to handle 1000LX and 1000CX somehow.
*/
if ((sc->mii_extcapabilities & EXTSR_1000XHDX) != 0) {
sc->mii_anegticks = MII_ANEGTICKS_GIGE;
sc->mii_flags |= MIIF_IS_1000X;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_SX, 0,
sc->mii_inst), MII_MEDIA_1000_X);
PRINT("1000baseSX");
}
if ((sc->mii_extcapabilities & EXTSR_1000XFDX) != 0) {
sc->mii_anegticks = MII_ANEGTICKS_GIGE;
sc->mii_flags |= MIIF_IS_1000X;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_SX, IFM_FDX,
sc->mii_inst), MII_MEDIA_1000_X_FDX);
PRINT("1000baseSX-FDX");
if ((sc->mii_flags & MIIF_DOPAUSE) != 0 &&
(sc->mii_flags & MIIF_NOMANPAUSE) == 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_SX,
IFM_FDX | IFM_FLOW, sc->mii_inst),
MII_MEDIA_1000_X_FDX);
PRINT("1000baseSX-FDX-flow");
}
fdx = 1;
}
/*
* 1000baseT media needs to be able to manipulate
* master/slave mode.
*
* All 1000baseT PHYs have a 1000baseT control register.
*/
if ((sc->mii_extcapabilities & EXTSR_1000THDX) != 0) {
sc->mii_anegticks = MII_ANEGTICKS_GIGE;
sc->mii_flags |= MIIF_HAVE_GTCR;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, 0,
sc->mii_inst), MII_MEDIA_1000_T);
PRINT("1000baseT");
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T,
IFM_ETH_MASTER, sc->mii_inst), MII_MEDIA_1000_T);
PRINT("1000baseT-master");
}
if ((sc->mii_extcapabilities & EXTSR_1000TFDX) != 0) {
sc->mii_anegticks = MII_ANEGTICKS_GIGE;
sc->mii_flags |= MIIF_HAVE_GTCR;
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T, IFM_FDX,
sc->mii_inst), MII_MEDIA_1000_T_FDX);
PRINT("1000baseT-FDX");
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T,
IFM_FDX | IFM_ETH_MASTER, sc->mii_inst),
MII_MEDIA_1000_T_FDX);
PRINT("1000baseT-FDX-master");
if ((sc->mii_flags & MIIF_DOPAUSE) != 0 &&
(sc->mii_flags & MIIF_NOMANPAUSE) == 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T,
IFM_FDX | IFM_FLOW, sc->mii_inst),
MII_MEDIA_1000_T_FDX);
PRINT("1000baseT-FDX-flow");
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_1000_T,
IFM_FDX | IFM_FLOW | IFM_ETH_MASTER,
sc->mii_inst), MII_MEDIA_1000_T_FDX);
PRINT("1000baseT-FDX-flow-master");
}
fdx = 1;
}
}
if ((sc->mii_capabilities & BMSR_ANEG) != 0) {
/* intentionally invalid index */
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_AUTO, 0, sc->mii_inst),
MII_NMEDIA);
PRINT("auto");
if (fdx != 0 && (sc->mii_flags & MIIF_DOPAUSE) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_AUTO, IFM_FLOW,
sc->mii_inst), MII_NMEDIA);
PRINT("auto-flow");
}
}
#undef ADD
#undef PRINT
}
int
mii_phy_detach(device_t dev)
{
struct mii_softc *sc;
sc = device_get_softc(dev);
mii_phy_down(sc);
sc->mii_dev = NULL;
LIST_REMOVE(sc, mii_list);
return (0);
}
const struct mii_phydesc *
mii_phy_match_gen(const struct mii_attach_args *ma,
const struct mii_phydesc *mpd, size_t len)
{
for (; mpd->mpd_name != NULL;
mpd = (const struct mii_phydesc *)((const char *)mpd + len)) {
if (MII_OUI(ma->mii_id1, ma->mii_id2) == mpd->mpd_oui &&
MII_MODEL(ma->mii_id2) == mpd->mpd_model)
return (mpd);
}
return (NULL);
}
const struct mii_phydesc *
mii_phy_match(const struct mii_attach_args *ma, const struct mii_phydesc *mpd)
{
return (mii_phy_match_gen(ma, mpd, sizeof(struct mii_phydesc)));
}
int
mii_phy_dev_probe(device_t dev, const struct mii_phydesc *mpd, int mrv)
{
mpd = mii_phy_match(device_get_ivars(dev), mpd);
if (mpd != NULL) {
device_set_desc(dev, mpd->mpd_name);
return (mrv);
}
return (ENXIO);
}
/*
* Return the flow control status flag from MII_ANAR & MII_ANLPAR.
*/
u_int
mii_phy_flowstatus(struct mii_softc *sc)
{
int anar, anlpar;
if ((sc->mii_flags & MIIF_DOPAUSE) == 0)
return (0);
anar = PHY_READ(sc, MII_ANAR);
anlpar = PHY_READ(sc, MII_ANLPAR);
/*
* Check for 1000BASE-X. Autonegotiation is a bit
* different on such devices.
*/
if ((sc->mii_flags & MIIF_IS_1000X) != 0) {
anar <<= 3;
anlpar <<= 3;
}
if ((anar & ANAR_PAUSE_SYM) != 0 && (anlpar & ANLPAR_PAUSE_SYM) != 0)
return (IFM_FLOW | IFM_ETH_TXPAUSE | IFM_ETH_RXPAUSE);
if ((anar & ANAR_PAUSE_SYM) == 0) {
if ((anar & ANAR_PAUSE_ASYM) != 0 &&
(anlpar & ANLPAR_PAUSE_TOWARDS) != 0)
return (IFM_FLOW | IFM_ETH_TXPAUSE);
else
return (0);
}
if ((anar & ANAR_PAUSE_ASYM) == 0) {
if ((anlpar & ANLPAR_PAUSE_SYM) != 0)
return (IFM_FLOW | IFM_ETH_TXPAUSE | IFM_ETH_RXPAUSE);
else
return (0);
}
switch ((anlpar & ANLPAR_PAUSE_TOWARDS)) {
case ANLPAR_PAUSE_NONE:
return (0);
case ANLPAR_PAUSE_ASYM:
return (IFM_FLOW | IFM_ETH_RXPAUSE);
default:
return (IFM_FLOW | IFM_ETH_RXPAUSE | IFM_ETH_TXPAUSE);
}
/* NOTREACHED */
}