3f9bdcef12
* Add in a default GPIO section for AR91XX_BASE.hints, which doesn't define the GPIO function masks or any GPIO pines. * Add in the GPIO line definitions for LEDs and GPIO pins for the TP-WR1043nd. I've verified the LEDs work fine using gpioset.
119 lines
2.8 KiB
Plaintext
119 lines
2.8 KiB
Plaintext
#
|
|
# This file adds to the values in AR91XX_BASE.hints.
|
|
#
|
|
# $FreeBSD$
|
|
|
|
# Hard-code the PHY for now, until there's switch phy support.
|
|
hint.arge.0.phymask=0x000c
|
|
hint.arge.0.media=1000
|
|
hint.arge.0.fduplex=1
|
|
# Where is the MAC address stored in flash for this particular unit.
|
|
hint.arge.0.eeprommac=0x1f01fc00
|
|
|
|
# This isn't used, but configure it anyway.
|
|
# This should eventually just not be configured, but the if then
|
|
# needs to be properly disabled or spurious interrupts occur.
|
|
hint.arge.1.phymask=0x0
|
|
|
|
# Where the ART is
|
|
hint.ath.0.eepromaddr=0x1fff1000
|
|
|
|
#
|
|
# Define a slightly custom flash layout.
|
|
|
|
# The default flash layout:
|
|
#
|
|
# 128k: uboot
|
|
# 1024k: kernel
|
|
# 4096k: rootfs
|
|
# 2816: unknown
|
|
# 64k: board config?
|
|
# 64k: ART
|
|
#
|
|
# from printenv:
|
|
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init
|
|
# mtdparts=ar9100-nor0:128k(u-boot),1024k(kernel),4096k(rootfs),64k(art)
|
|
|
|
# This isn't a lot of space!
|
|
# So:
|
|
# 128k: uboot
|
|
# 2048k: kernel
|
|
# 5888k: rootfs
|
|
# 64k: config
|
|
# 64k: ART
|
|
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x000200000
|
|
hint.map.0.name="uboot"
|
|
hint.map.0.readonly=1
|
|
|
|
hint.map.1.at="flash/spi0"
|
|
hint.map.1.start=0x00020000
|
|
hint.map.1.end=0x00220000
|
|
hint.map.1.name="kernel"
|
|
hint.map.1.readonly=1
|
|
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start=0x00220000
|
|
hint.map.2.end=0x007e0000
|
|
hint.map.2.name="rootfs"
|
|
hint.map.2.readonly=1
|
|
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start=0x007e0000
|
|
hint.map.3.end=0x007f0000
|
|
hint.map.3.name="cfg"
|
|
hint.map.3.readonly=0
|
|
|
|
# This is radio calibration section. It is (or should be!) unique
|
|
# for each board, to take into account thermal and electrical differences
|
|
# as well as the regulatory compliance data.
|
|
#
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x007f0000
|
|
hint.map.4.end=0x00800000
|
|
hint.map.4.name="art"
|
|
hint.map.4.readonly=1
|
|
|
|
# GPIO specific configuration block
|
|
|
|
# Don't flip on anything that isn't already enabled.
|
|
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
|
|
# not used here.
|
|
hint.gpio.0.function_set=0x00000000
|
|
hint.gpio.0.function_clear=0x00000000
|
|
|
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
|
hint.gpio.0.pinmask=0x001c02ae
|
|
|
|
# pin 1 - USB (LED)
|
|
# pin 2 - System (LED)
|
|
# Pin 3 - Reset (input)
|
|
# Pin 5 - QSS (LED)
|
|
# Pin 7 - QSS Button (input)
|
|
# Pin 8 - wired into the chip reset line
|
|
# Pin 9 - WLAN
|
|
# Pin 10 - UART TX (not GPIO)
|
|
# Pin 13 - UART RX (not GPIO)
|
|
# Pin 18 - RTL8366RB switch data line
|
|
# Pin 19 - RTL8366RB switch clock line
|
|
# Pin 20 - "GPIO20"
|
|
|
|
# LEDs are configured separately and driven by the LED device
|
|
hint.gpioled.0.at="gpiobus0"
|
|
hint.gpioled.0.name="usb"
|
|
hint.gpioled.0.pins=0x0002
|
|
|
|
hint.gpioled.1.at="gpiobus0"
|
|
hint.gpioled.1.name="system"
|
|
hint.gpioled.1.pins=0x0004
|
|
|
|
hint.gpioled.2.at="gpiobus0"
|
|
hint.gpioled.2.name="qss"
|
|
hint.gpioled.2.pins=0x0020
|
|
|
|
hint.gpioled.3.at="gpiobus0"
|
|
hint.gpioled.3.name="wlan"
|
|
hint.gpioled.3.pins=0x0200
|