562246dff8
specially aml8726-m6 and aml8726-m8b SoC based devices. aml8726-m6 SoC exist in devices such as Visson ATV-102. Hardkernel ODROID-C1 board has aml8726-m8b SoC. The following support is included: Basic machdep code SMP Interrupt controller Clock control driver (aka gate) Pinctrl Timer Real time clock UART GPIO I2C SD controller SDXC controller USB Watchdog Random number generator PLL / Clock frequency measurement Frame buffer Submitted by: John Wehle Approved by: stas (mentor)
181 lines
4.3 KiB
C
181 lines
4.3 KiB
C
/*-
|
|
* Copyright 2013-2015 John Wehle <john@feith.com>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* Amlogic aml8726 UART console driver.
|
|
*
|
|
* This is only necessary to use when debugging early boot code.
|
|
* The standard uart driver is available for use later in the boot.
|
|
*
|
|
* It's assumed the SoC uart is mapped into AML_UART_KVM_BASE meaning
|
|
* when using EARLY_PRINTF you'll need to define SOCDEV_VA to be
|
|
* 0xd8100000 and SOCDEV_PA to be 0xc8100000 in your config file.
|
|
*/
|
|
|
|
#include "opt_global.h"
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/conf.h>
|
|
#include <sys/cons.h>
|
|
#include <sys/consio.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/sysctl.h>
|
|
|
|
#include <machine/bus.h>
|
|
#include <machine/cpu.h>
|
|
|
|
#include <arm/amlogic/aml8726/aml8726_machdep.h>
|
|
#include <arm/amlogic/aml8726/aml8726_uart.h>
|
|
|
|
#define AML_UART_KVM_BASE (aml8726_aobus_kva_base + 0x130 * 4)
|
|
|
|
static uint32_t
|
|
ub_getreg(uint32_t off)
|
|
{
|
|
|
|
return *((volatile uint32_t *)(AML_UART_KVM_BASE + off));
|
|
}
|
|
|
|
static void
|
|
ub_setreg(uint32_t off, uint32_t val)
|
|
{
|
|
|
|
*((volatile uint32_t *)(AML_UART_KVM_BASE + off)) = val;
|
|
}
|
|
|
|
static void
|
|
uart_cnprobe(struct consdev *cp)
|
|
{
|
|
|
|
sprintf(cp->cn_name, "uart");
|
|
cp->cn_pri = CN_REMOTE;
|
|
}
|
|
|
|
static void
|
|
uart_cngrab(struct consdev *cp)
|
|
{
|
|
}
|
|
|
|
static void
|
|
uart_cnungrab(struct consdev *cp)
|
|
{
|
|
}
|
|
|
|
static void
|
|
uart_cninit(struct consdev *cp)
|
|
{
|
|
uint32_t cr;
|
|
uint32_t mr;
|
|
|
|
#ifdef EARLY_PRINTF
|
|
if (early_putc != NULL) {
|
|
printf("Early printf yielding control to the real console.\n");
|
|
early_putc = NULL;
|
|
}
|
|
|
|
/*
|
|
* Give pending characters a chance to drain.
|
|
*/
|
|
DELAY(4000);
|
|
#endif
|
|
|
|
cr = ub_getreg(AML_UART_CONTROL_REG);
|
|
/* Disable all interrupt sources. */
|
|
cr &= ~(AML_UART_CONTROL_TX_INT_EN | AML_UART_CONTROL_RX_INT_EN);
|
|
/* Reset the transmitter and receiver. */
|
|
cr |= (AML_UART_CONTROL_TX_RST | AML_UART_CONTROL_RX_RST);
|
|
/* Use two wire mode. */
|
|
cr |= AML_UART_CONTROL_TWO_WIRE_EN;
|
|
/* Enable the transmitter and receiver. */
|
|
cr |= (AML_UART_CONTROL_TX_EN | AML_UART_CONTROL_RX_EN);
|
|
ub_setreg(AML_UART_CONTROL_REG, cr);
|
|
|
|
/* Clear RX FIFO level for generating interrupts. */
|
|
mr = ub_getreg(AML_UART_MISC_REG);
|
|
mr &= ~AML_UART_MISC_RECV_IRQ_CNT_MASK;
|
|
ub_setreg(AML_UART_MISC_REG, mr);
|
|
|
|
/* Ensure the reset bits are clear. */
|
|
cr &= ~(AML_UART_CONTROL_TX_RST | AML_UART_CONTROL_RX_RST);
|
|
ub_setreg(AML_UART_CONTROL_REG, cr);
|
|
}
|
|
|
|
static void
|
|
uart_cnterm(struct consdev * cp)
|
|
{
|
|
}
|
|
|
|
static void
|
|
uart_cnputc(struct consdev *cp, int c)
|
|
{
|
|
|
|
while ((ub_getreg(AML_UART_STATUS_REG) &
|
|
AML_UART_STATUS_TX_FIFO_FULL) != 0)
|
|
cpu_spinwait();
|
|
|
|
ub_setreg(AML_UART_WFIFO_REG, c);
|
|
}
|
|
|
|
static int
|
|
uart_cngetc(struct consdev * cp)
|
|
{
|
|
int c;
|
|
|
|
if ((ub_getreg(AML_UART_STATUS_REG) &
|
|
AML_UART_STATUS_RX_FIFO_EMPTY) != 0)
|
|
return (-1);
|
|
|
|
c = ub_getreg(AML_UART_RFIFO_REG) & 0xff;
|
|
|
|
return (c);
|
|
}
|
|
|
|
CONSOLE_DRIVER(uart);
|
|
|
|
#ifdef EARLY_PRINTF
|
|
|
|
#if !(defined(SOCDEV_PA) && defined(SOCDEV_VA))
|
|
#error SOCDEV_PA and SOCDEV_VA must be defined.
|
|
#endif
|
|
|
|
static void
|
|
eputc(int c)
|
|
{
|
|
|
|
if (c == '\n')
|
|
eputc('\r');
|
|
|
|
uart_cnputc(NULL, c);
|
|
}
|
|
|
|
early_putc_t *early_putc = eputc;
|
|
#endif
|