143cfad710
encryption types. The AR5210 only has four WEP key slots, in contrast to what the later MACs have (ie, the keycache.) So there's no way to store a "clear" key. Even if the driver is taught to not allocate CLR key entries for the AR5210, the hardware will actually attempt to decode the encrypted frames with the (likely all 0!) WEP keys. So for now, disable the hardware encryption entirely and just so it all in software. That allows both WEP -and- WPA to actually work. If someone wishes to try and make hardware WEP _but_ software WPA work, they'll have to create a HAL capability to enable/disable hardware encryption based on the current STA/Hostap mode. However, making multi-vap work with one WEP and one WPA VAP will require hardware encryption to be disabled anyway.
1002 lines
28 KiB
C
1002 lines
28 KiB
C
/*
|
|
* Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
|
|
* Copyright (c) 2002-2004 Atheros Communications, Inc.
|
|
*
|
|
* Permission to use, copy, modify, and/or distribute this software for any
|
|
* purpose with or without fee is hereby granted, provided that the above
|
|
* copyright notice and this permission notice appear in all copies.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
|
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
|
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
|
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
|
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
|
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
#include "opt_ah.h"
|
|
|
|
#include "ah.h"
|
|
#include "ah_internal.h"
|
|
|
|
#include "ar5210/ar5210.h"
|
|
#include "ar5210/ar5210reg.h"
|
|
#include "ar5210/ar5210phy.h"
|
|
|
|
#include "ah_eeprom_v1.h"
|
|
|
|
typedef struct {
|
|
uint32_t Offset;
|
|
uint32_t Value;
|
|
} REGISTER_VAL;
|
|
|
|
static const REGISTER_VAL ar5k0007_init[] = {
|
|
#include "ar5210/ar5k_0007.ini"
|
|
};
|
|
|
|
/* Default Power Settings for channels outside of EEPROM range */
|
|
static const uint8_t ar5k0007_pwrSettings[17] = {
|
|
/* gain delta pc dac */
|
|
/* 54 48 36 24 18 12 9 54 48 36 24 18 12 9 6 ob db */
|
|
9, 9, 0, 0, 0, 0, 0, 2, 2, 6, 6, 6, 6, 6, 6, 2, 2
|
|
};
|
|
|
|
/*
|
|
* The delay, in usecs, between writing AR_RC with a reset
|
|
* request and waiting for the chip to settle. If this is
|
|
* too short then the chip does not come out of sleep state.
|
|
* Note this value was empirically derived and may be dependent
|
|
* on the host machine (don't know--the problem was identified
|
|
* on an IBM 570e laptop; 10us delays worked on other systems).
|
|
*/
|
|
#define AR_RC_SETTLE_TIME 20000
|
|
|
|
static HAL_BOOL ar5210SetResetReg(struct ath_hal *,
|
|
uint32_t resetMask, u_int delay);
|
|
static HAL_BOOL ar5210SetChannel(struct ath_hal *, struct ieee80211_channel *);
|
|
static void ar5210SetOperatingMode(struct ath_hal *, int opmode);
|
|
|
|
/*
|
|
* Places the device in and out of reset and then places sane
|
|
* values in the registers based on EEPROM config, initialization
|
|
* vectors (as determined by the mode), and station configuration
|
|
*
|
|
* bChannelChange is used to preserve DMA/PCU registers across
|
|
* a HW Reset during channel change.
|
|
*/
|
|
HAL_BOOL
|
|
ar5210Reset(struct ath_hal *ah, HAL_OPMODE opmode,
|
|
struct ieee80211_channel *chan, HAL_BOOL bChannelChange,
|
|
HAL_STATUS *status)
|
|
{
|
|
#define N(a) (sizeof (a) /sizeof (a[0]))
|
|
#define FAIL(_code) do { ecode = _code; goto bad; } while (0)
|
|
struct ath_hal_5210 *ahp = AH5210(ah);
|
|
const HAL_EEPROM_v1 *ee = AH_PRIVATE(ah)->ah_eeprom;
|
|
HAL_CHANNEL_INTERNAL *ichan;
|
|
HAL_STATUS ecode;
|
|
uint32_t ledstate;
|
|
int i, q;
|
|
|
|
HALDEBUG(ah, HAL_DEBUG_RESET,
|
|
"%s: opmode %u channel %u/0x%x %s channel\n", __func__,
|
|
opmode, chan->ic_freq, chan->ic_flags,
|
|
bChannelChange ? "change" : "same");
|
|
|
|
if (!IEEE80211_IS_CHAN_5GHZ(chan)) {
|
|
/* Only 11a mode */
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: channel not 5GHz\n", __func__);
|
|
FAIL(HAL_EINVAL);
|
|
}
|
|
/*
|
|
* Map public channel to private.
|
|
*/
|
|
ichan = ath_hal_checkchannel(ah, chan);
|
|
if (ichan == AH_NULL) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY,
|
|
"%s: invalid channel %u/0x%x; no mapping\n",
|
|
__func__, chan->ic_freq, chan->ic_flags);
|
|
FAIL(HAL_EINVAL);
|
|
}
|
|
switch (opmode) {
|
|
case HAL_M_STA:
|
|
case HAL_M_IBSS:
|
|
case HAL_M_HOSTAP:
|
|
case HAL_M_MONITOR:
|
|
break;
|
|
default:
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: invalid operating mode %u\n",
|
|
__func__, opmode);
|
|
FAIL(HAL_EINVAL);
|
|
break;
|
|
}
|
|
|
|
ledstate = OS_REG_READ(ah, AR_PCICFG) &
|
|
(AR_PCICFG_LED_PEND | AR_PCICFG_LED_ACT);
|
|
|
|
if (!ar5210ChipReset(ah, chan)) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n",
|
|
__func__);
|
|
FAIL(HAL_EIO);
|
|
}
|
|
|
|
OS_REG_WRITE(ah, AR_STA_ID0, LE_READ_4(ahp->ah_macaddr));
|
|
OS_REG_WRITE(ah, AR_STA_ID1, LE_READ_2(ahp->ah_macaddr + 4));
|
|
ar5210SetOperatingMode(ah, opmode);
|
|
|
|
switch (opmode) {
|
|
case HAL_M_HOSTAP:
|
|
OS_REG_WRITE(ah, AR_BCR, INIT_BCON_CNTRL_REG);
|
|
OS_REG_WRITE(ah, AR_PCICFG,
|
|
AR_PCICFG_LED_ACT | AR_PCICFG_LED_BCTL);
|
|
break;
|
|
case HAL_M_IBSS:
|
|
OS_REG_WRITE(ah, AR_BCR, INIT_BCON_CNTRL_REG | AR_BCR_BCMD);
|
|
OS_REG_WRITE(ah, AR_PCICFG,
|
|
AR_PCICFG_CLKRUNEN | AR_PCICFG_LED_PEND | AR_PCICFG_LED_BCTL);
|
|
break;
|
|
case HAL_M_STA:
|
|
OS_REG_WRITE(ah, AR_BCR, INIT_BCON_CNTRL_REG);
|
|
OS_REG_WRITE(ah, AR_PCICFG,
|
|
AR_PCICFG_CLKRUNEN | AR_PCICFG_LED_PEND | AR_PCICFG_LED_BCTL);
|
|
break;
|
|
case HAL_M_MONITOR:
|
|
OS_REG_WRITE(ah, AR_BCR, INIT_BCON_CNTRL_REG);
|
|
OS_REG_WRITE(ah, AR_PCICFG,
|
|
AR_PCICFG_LED_ACT | AR_PCICFG_LED_BCTL);
|
|
break;
|
|
}
|
|
|
|
/* Restore previous led state */
|
|
OS_REG_WRITE(ah, AR_PCICFG, OS_REG_READ(ah, AR_PCICFG) | ledstate);
|
|
|
|
OS_REG_WRITE(ah, AR_BSS_ID0, LE_READ_4(ahp->ah_bssid));
|
|
OS_REG_WRITE(ah, AR_BSS_ID1, LE_READ_2(ahp->ah_bssid + 4));
|
|
|
|
OS_REG_WRITE(ah, AR_TXDP0, 0);
|
|
OS_REG_WRITE(ah, AR_TXDP1, 0);
|
|
OS_REG_WRITE(ah, AR_RXDP, 0);
|
|
|
|
/*
|
|
* Initialize interrupt state.
|
|
*/
|
|
(void) OS_REG_READ(ah, AR_ISR); /* cleared on read */
|
|
OS_REG_WRITE(ah, AR_IMR, 0);
|
|
OS_REG_WRITE(ah, AR_IER, AR_IER_DISABLE);
|
|
ahp->ah_maskReg = 0;
|
|
|
|
(void) OS_REG_READ(ah, AR_BSR); /* cleared on read */
|
|
OS_REG_WRITE(ah, AR_TXCFG, AR_DMASIZE_128B);
|
|
OS_REG_WRITE(ah, AR_RXCFG, AR_DMASIZE_128B);
|
|
|
|
OS_REG_WRITE(ah, AR_TOPS, 8); /* timeout prescale */
|
|
OS_REG_WRITE(ah, AR_RXNOFRM, 8); /* RX no frame timeout */
|
|
OS_REG_WRITE(ah, AR_RPGTO, 0); /* RX frame gap timeout */
|
|
OS_REG_WRITE(ah, AR_TXNOFRM, 0); /* TX no frame timeout */
|
|
|
|
OS_REG_WRITE(ah, AR_SFR, 0);
|
|
OS_REG_WRITE(ah, AR_MIBC, 0); /* unfreeze ctrs + clr state */
|
|
OS_REG_WRITE(ah, AR_RSSI_THR, ahp->ah_rssiThr);
|
|
OS_REG_WRITE(ah, AR_CFP_DUR, 0);
|
|
|
|
ar5210SetRxFilter(ah, 0); /* nothing for now */
|
|
OS_REG_WRITE(ah, AR_MCAST_FIL0, 0); /* multicast filter */
|
|
OS_REG_WRITE(ah, AR_MCAST_FIL1, 0); /* XXX was 2 */
|
|
|
|
OS_REG_WRITE(ah, AR_TX_MASK0, 0);
|
|
OS_REG_WRITE(ah, AR_TX_MASK1, 0);
|
|
OS_REG_WRITE(ah, AR_CLR_TMASK, 1);
|
|
OS_REG_WRITE(ah, AR_TRIG_LEV, 1); /* minimum */
|
|
|
|
ar5210UpdateDiagReg(ah, 0);
|
|
|
|
OS_REG_WRITE(ah, AR_CFP_PERIOD, 0);
|
|
OS_REG_WRITE(ah, AR_TIMER0, 0); /* next beacon time */
|
|
OS_REG_WRITE(ah, AR_TSF_L32, 0); /* local clock */
|
|
OS_REG_WRITE(ah, AR_TIMER1, ~0); /* next DMA beacon alert */
|
|
OS_REG_WRITE(ah, AR_TIMER2, ~0); /* next SW beacon alert */
|
|
OS_REG_WRITE(ah, AR_TIMER3, 1); /* next ATIM window */
|
|
|
|
/* Write the INI values for PHYreg initialization */
|
|
for (i = 0; i < N(ar5k0007_init); i++) {
|
|
uint32_t reg = ar5k0007_init[i].Offset;
|
|
/* On channel change, don't reset the PCU registers */
|
|
if (!(bChannelChange && (0x8000 <= reg && reg < 0x9000)))
|
|
OS_REG_WRITE(ah, reg, ar5k0007_init[i].Value);
|
|
}
|
|
|
|
/* Setup the transmit power values for cards since 0x0[0-2]05 */
|
|
if (!ar5210SetTransmitPower(ah, chan)) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY,
|
|
"%s: error init'ing transmit power\n", __func__);
|
|
FAIL(HAL_EIO);
|
|
}
|
|
|
|
OS_REG_WRITE(ah, AR_PHY(10),
|
|
(OS_REG_READ(ah, AR_PHY(10)) & 0xFFFF00FF) |
|
|
(ee->ee_xlnaOn << 8));
|
|
OS_REG_WRITE(ah, AR_PHY(13),
|
|
(ee->ee_xpaOff << 24) | (ee->ee_xpaOff << 16) |
|
|
(ee->ee_xpaOn << 8) | ee->ee_xpaOn);
|
|
OS_REG_WRITE(ah, AR_PHY(17),
|
|
(OS_REG_READ(ah, AR_PHY(17)) & 0xFFFFC07F) |
|
|
((ee->ee_antenna >> 1) & 0x3F80));
|
|
OS_REG_WRITE(ah, AR_PHY(18),
|
|
(OS_REG_READ(ah, AR_PHY(18)) & 0xFFFC0FFF) |
|
|
((ee->ee_antenna << 10) & 0x3F000));
|
|
OS_REG_WRITE(ah, AR_PHY(25),
|
|
(OS_REG_READ(ah, AR_PHY(25)) & 0xFFF80FFF) |
|
|
((ee->ee_thresh62 << 12) & 0x7F000));
|
|
OS_REG_WRITE(ah, AR_PHY(68),
|
|
(OS_REG_READ(ah, AR_PHY(68)) & 0xFFFFFFFC) |
|
|
(ee->ee_antenna & 0x3));
|
|
|
|
if (!ar5210SetChannel(ah, chan)) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: unable to set channel\n",
|
|
__func__);
|
|
FAIL(HAL_EIO);
|
|
}
|
|
if (bChannelChange && !IEEE80211_IS_CHAN_DFS(chan))
|
|
chan->ic_state &= ~IEEE80211_CHANSTATE_CWINT;
|
|
|
|
/* Activate the PHY */
|
|
OS_REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ENABLE);
|
|
|
|
OS_DELAY(1000); /* Wait a bit (1 msec) */
|
|
|
|
/* calibrate the HW and poll the bit going to 0 for completion */
|
|
OS_REG_WRITE(ah, AR_PHY_AGCCTL,
|
|
OS_REG_READ(ah, AR_PHY_AGCCTL) | AR_PHY_AGC_CAL);
|
|
(void) ath_hal_wait(ah, AR_PHY_AGCCTL, AR_PHY_AGC_CAL, 0);
|
|
|
|
/* Perform noise floor calibration and set status */
|
|
if (!ar5210CalNoiseFloor(ah, ichan)) {
|
|
chan->ic_state |= IEEE80211_CHANSTATE_CWINT;
|
|
HALDEBUG(ah, HAL_DEBUG_ANY,
|
|
"%s: noise floor calibration failed\n", __func__);
|
|
FAIL(HAL_EIO);
|
|
}
|
|
|
|
for (q = 0; q < HAL_NUM_TX_QUEUES; q++)
|
|
ar5210ResetTxQueue(ah, q);
|
|
|
|
if (AH_PRIVATE(ah)->ah_rfkillEnabled)
|
|
ar5210EnableRfKill(ah);
|
|
|
|
/*
|
|
* Writing to AR_BEACON will start timers. Hence it should be
|
|
* the last register to be written. Do not reset tsf, do not
|
|
* enable beacons at this point, but preserve other values
|
|
* like beaconInterval.
|
|
*/
|
|
OS_REG_WRITE(ah, AR_BEACON,
|
|
(OS_REG_READ(ah, AR_BEACON) &
|
|
~(AR_BEACON_EN | AR_BEACON_RESET_TSF)));
|
|
|
|
/* Restore user-specified slot time and timeouts */
|
|
if (ahp->ah_sifstime != (u_int) -1)
|
|
ar5210SetSifsTime(ah, ahp->ah_sifstime);
|
|
if (ahp->ah_slottime != (u_int) -1)
|
|
ar5210SetSlotTime(ah, ahp->ah_slottime);
|
|
if (ahp->ah_acktimeout != (u_int) -1)
|
|
ar5210SetAckTimeout(ah, ahp->ah_acktimeout);
|
|
if (ahp->ah_ctstimeout != (u_int) -1)
|
|
ar5210SetCTSTimeout(ah, ahp->ah_ctstimeout);
|
|
if (AH_PRIVATE(ah)->ah_diagreg != 0)
|
|
ar5210UpdateDiagReg(ah, AH_PRIVATE(ah)->ah_diagreg);
|
|
|
|
AH_PRIVATE(ah)->ah_opmode = opmode; /* record operating mode */
|
|
|
|
HALDEBUG(ah, HAL_DEBUG_RESET, "%s: done\n", __func__);
|
|
|
|
return AH_TRUE;
|
|
bad:
|
|
if (status != AH_NULL)
|
|
*status = ecode;
|
|
return AH_FALSE;
|
|
#undef FAIL
|
|
#undef N
|
|
}
|
|
|
|
static void
|
|
ar5210SetOperatingMode(struct ath_hal *ah, int opmode)
|
|
{
|
|
struct ath_hal_5210 *ahp = AH5210(ah);
|
|
uint32_t val;
|
|
|
|
val = OS_REG_READ(ah, AR_STA_ID1) & 0xffff;
|
|
switch (opmode) {
|
|
case HAL_M_HOSTAP:
|
|
OS_REG_WRITE(ah, AR_STA_ID1, val
|
|
| AR_STA_ID1_AP
|
|
| AR_STA_ID1_NO_PSPOLL
|
|
| AR_STA_ID1_DESC_ANTENNA
|
|
| ahp->ah_staId1Defaults);
|
|
break;
|
|
case HAL_M_IBSS:
|
|
OS_REG_WRITE(ah, AR_STA_ID1, val
|
|
| AR_STA_ID1_ADHOC
|
|
| AR_STA_ID1_NO_PSPOLL
|
|
| AR_STA_ID1_DESC_ANTENNA
|
|
| ahp->ah_staId1Defaults);
|
|
break;
|
|
case HAL_M_STA:
|
|
OS_REG_WRITE(ah, AR_STA_ID1, val
|
|
| AR_STA_ID1_NO_PSPOLL
|
|
| AR_STA_ID1_PWR_SV
|
|
| ahp->ah_staId1Defaults);
|
|
break;
|
|
case HAL_M_MONITOR:
|
|
OS_REG_WRITE(ah, AR_STA_ID1, val
|
|
| AR_STA_ID1_NO_PSPOLL
|
|
| ahp->ah_staId1Defaults);
|
|
break;
|
|
}
|
|
}
|
|
|
|
void
|
|
ar5210SetPCUConfig(struct ath_hal *ah)
|
|
{
|
|
ar5210SetOperatingMode(ah, AH_PRIVATE(ah)->ah_opmode);
|
|
}
|
|
|
|
/*
|
|
* Places the PHY and Radio chips into reset. A full reset
|
|
* must be called to leave this state. The PCI/MAC/PCU are
|
|
* not placed into reset as we must receive interrupt to
|
|
* re-enable the hardware.
|
|
*/
|
|
HAL_BOOL
|
|
ar5210PhyDisable(struct ath_hal *ah)
|
|
{
|
|
return ar5210SetResetReg(ah, AR_RC_RPHY, 10);
|
|
}
|
|
|
|
/*
|
|
* Places all of hardware into reset
|
|
*/
|
|
HAL_BOOL
|
|
ar5210Disable(struct ath_hal *ah)
|
|
{
|
|
#define AR_RC_HW (AR_RC_RPCU | AR_RC_RDMA | AR_RC_RPHY | AR_RC_RMAC)
|
|
if (!ar5210SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE))
|
|
return AH_FALSE;
|
|
|
|
/*
|
|
* Reset the HW - PCI must be reset after the rest of the
|
|
* device has been reset
|
|
*/
|
|
if (!ar5210SetResetReg(ah, AR_RC_HW, AR_RC_SETTLE_TIME))
|
|
return AH_FALSE;
|
|
OS_DELAY(1000);
|
|
(void) ar5210SetResetReg(ah, AR_RC_HW | AR_RC_RPCI, AR_RC_SETTLE_TIME);
|
|
OS_DELAY(2100); /* 8245 @ 96Mhz hangs with 2000us. */
|
|
|
|
return AH_TRUE;
|
|
#undef AR_RC_HW
|
|
}
|
|
|
|
/*
|
|
* Places the hardware into reset and then pulls it out of reset
|
|
*/
|
|
HAL_BOOL
|
|
ar5210ChipReset(struct ath_hal *ah, struct ieee80211_channel *chan)
|
|
{
|
|
#define AR_RC_HW (AR_RC_RPCU | AR_RC_RDMA | AR_RC_RPHY | AR_RC_RMAC)
|
|
|
|
HALDEBUG(ah, HAL_DEBUG_RESET, "%s turbo %s\n", __func__,
|
|
chan && IEEE80211_IS_CHAN_TURBO(chan) ?
|
|
"enabled" : "disabled");
|
|
|
|
if (!ar5210SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE))
|
|
return AH_FALSE;
|
|
|
|
/* Place chip in turbo before reset to cleanly reset clocks */
|
|
OS_REG_WRITE(ah, AR_PHY_FRCTL,
|
|
chan && IEEE80211_IS_CHAN_TURBO(chan) ? AR_PHY_TURBO_MODE : 0);
|
|
|
|
/*
|
|
* Reset the HW.
|
|
* PCI must be reset after the rest of the device has been reset.
|
|
*/
|
|
if (!ar5210SetResetReg(ah, AR_RC_HW, AR_RC_SETTLE_TIME))
|
|
return AH_FALSE;
|
|
OS_DELAY(1000);
|
|
if (!ar5210SetResetReg(ah, AR_RC_HW | AR_RC_RPCI, AR_RC_SETTLE_TIME))
|
|
return AH_FALSE;
|
|
OS_DELAY(2100); /* 8245 @ 96Mhz hangs with 2000us. */
|
|
|
|
/*
|
|
* Bring out of sleep mode (AGAIN)
|
|
*
|
|
* WARNING WARNING WARNING
|
|
*
|
|
* There is a problem with the chip where it doesn't always indicate
|
|
* that it's awake, so initializePowerUp() will fail.
|
|
*/
|
|
if (!ar5210SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE))
|
|
return AH_FALSE;
|
|
|
|
/* Clear warm reset reg */
|
|
return ar5210SetResetReg(ah, 0, 10);
|
|
#undef AR_RC_HW
|
|
}
|
|
|
|
enum {
|
|
FIRPWR_M = 0x03fc0000,
|
|
FIRPWR_S = 18,
|
|
KCOARSEHIGH_M = 0x003f8000,
|
|
KCOARSEHIGH_S = 15,
|
|
KCOARSELOW_M = 0x00007f80,
|
|
KCOARSELOW_S = 7,
|
|
ADCSAT_ICOUNT_M = 0x0001f800,
|
|
ADCSAT_ICOUNT_S = 11,
|
|
ADCSAT_THRESH_M = 0x000007e0,
|
|
ADCSAT_THRESH_S = 5
|
|
};
|
|
|
|
/*
|
|
* Recalibrate the lower PHY chips to account for temperature/environment
|
|
* changes.
|
|
*/
|
|
HAL_BOOL
|
|
ar5210PerCalibrationN(struct ath_hal *ah,
|
|
struct ieee80211_channel *chan, u_int chainMask,
|
|
HAL_BOOL longCal, HAL_BOOL *isCalDone)
|
|
{
|
|
uint32_t regBeacon;
|
|
uint32_t reg9858, reg985c, reg9868;
|
|
HAL_CHANNEL_INTERNAL *ichan;
|
|
|
|
ichan = ath_hal_checkchannel(ah, chan);
|
|
if (ichan == AH_NULL)
|
|
return AH_FALSE;
|
|
/* Disable tx and rx */
|
|
ar5210UpdateDiagReg(ah,
|
|
OS_REG_READ(ah, AR_DIAG_SW) | (AR_DIAG_SW_DIS_TX | AR_DIAG_SW_DIS_RX));
|
|
|
|
/* Disable Beacon Enable */
|
|
regBeacon = OS_REG_READ(ah, AR_BEACON);
|
|
OS_REG_WRITE(ah, AR_BEACON, regBeacon & ~AR_BEACON_EN);
|
|
|
|
/* Delay 4ms to ensure that all tx and rx activity has ceased */
|
|
OS_DELAY(4000);
|
|
|
|
/* Disable AGC to radio traffic */
|
|
OS_REG_WRITE(ah, 0x9808, OS_REG_READ(ah, 0x9808) | 0x08000000);
|
|
/* Wait for the AGC traffic to cease. */
|
|
OS_DELAY(10);
|
|
|
|
/* Change Channel to relock synth */
|
|
if (!ar5210SetChannel(ah, chan))
|
|
return AH_FALSE;
|
|
|
|
/* wait for the synthesizer lock to stabilize */
|
|
OS_DELAY(1000);
|
|
|
|
/* Re-enable AGC to radio traffic */
|
|
OS_REG_WRITE(ah, 0x9808, OS_REG_READ(ah, 0x9808) & (~0x08000000));
|
|
|
|
/*
|
|
* Configure the AGC so that it is highly unlikely (if not
|
|
* impossible) for it to send any gain changes to the analog
|
|
* chip. We store off the current values so that they can
|
|
* be rewritten below. Setting the following values:
|
|
* firpwr = -1
|
|
* Kcoursehigh = -1
|
|
* Kcourselow = -127
|
|
* ADCsat_icount = 2
|
|
* ADCsat_thresh = 12
|
|
*/
|
|
reg9858 = OS_REG_READ(ah, 0x9858);
|
|
reg985c = OS_REG_READ(ah, 0x985c);
|
|
reg9868 = OS_REG_READ(ah, 0x9868);
|
|
|
|
OS_REG_WRITE(ah, 0x9858, (reg9858 & ~FIRPWR_M) |
|
|
((-1 << FIRPWR_S) & FIRPWR_M));
|
|
OS_REG_WRITE(ah, 0x985c,
|
|
(reg985c & ~(KCOARSEHIGH_M | KCOARSELOW_M)) |
|
|
((-1 << KCOARSEHIGH_S) & KCOARSEHIGH_M) |
|
|
((-127 << KCOARSELOW_S) & KCOARSELOW_M));
|
|
OS_REG_WRITE(ah, 0x9868,
|
|
(reg9868 & ~(ADCSAT_ICOUNT_M | ADCSAT_THRESH_M)) |
|
|
((2 << ADCSAT_ICOUNT_S) & ADCSAT_ICOUNT_M) |
|
|
((12 << ADCSAT_THRESH_S) & ADCSAT_THRESH_M));
|
|
|
|
/* Wait for AGC changes to be enacted */
|
|
OS_DELAY(20);
|
|
|
|
/*
|
|
* We disable RF mix/gain stages for the PGA to avoid a
|
|
* race condition that will occur with receiving a frame
|
|
* and performing the AGC calibration. This will be
|
|
* re-enabled at the end of offset cal. We turn off AGC
|
|
* writes during this write as it will go over the analog bus.
|
|
*/
|
|
OS_REG_WRITE(ah, 0x9808, OS_REG_READ(ah, 0x9808) | 0x08000000);
|
|
OS_DELAY(10); /* wait for the AGC traffic to cease */
|
|
OS_REG_WRITE(ah, 0x98D4, 0x21);
|
|
OS_REG_WRITE(ah, 0x9808, OS_REG_READ(ah, 0x9808) & (~0x08000000));
|
|
|
|
/* wait to make sure that additional AGC traffic has quiesced */
|
|
OS_DELAY(1000);
|
|
|
|
/* AGC calibration (this was added to make the NF threshold check work) */
|
|
OS_REG_WRITE(ah, AR_PHY_AGCCTL,
|
|
OS_REG_READ(ah, AR_PHY_AGCCTL) | AR_PHY_AGC_CAL);
|
|
if (!ath_hal_wait(ah, AR_PHY_AGCCTL, AR_PHY_AGC_CAL, 0)) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: AGC calibration timeout\n",
|
|
__func__);
|
|
}
|
|
|
|
/* Rewrite our AGC values we stored off earlier (return AGC to normal operation) */
|
|
OS_REG_WRITE(ah, 0x9858, reg9858);
|
|
OS_REG_WRITE(ah, 0x985c, reg985c);
|
|
OS_REG_WRITE(ah, 0x9868, reg9868);
|
|
|
|
/* Perform noise floor and set status */
|
|
if (!ar5210CalNoiseFloor(ah, ichan)) {
|
|
/*
|
|
* Delay 5ms before retrying the noise floor -
|
|
* just to make sure. We're in an error
|
|
* condition here
|
|
*/
|
|
HALDEBUG(ah, HAL_DEBUG_NFCAL | HAL_DEBUG_PERCAL,
|
|
"%s: Performing 2nd Noise Cal\n", __func__);
|
|
OS_DELAY(5000);
|
|
if (!ar5210CalNoiseFloor(ah, ichan))
|
|
chan->ic_state |= IEEE80211_CHANSTATE_CWINT;
|
|
}
|
|
|
|
/* Clear tx and rx disable bit */
|
|
ar5210UpdateDiagReg(ah,
|
|
OS_REG_READ(ah, AR_DIAG_SW) & ~(AR_DIAG_SW_DIS_TX | AR_DIAG_SW_DIS_RX));
|
|
|
|
/* Re-enable Beacons */
|
|
OS_REG_WRITE(ah, AR_BEACON, regBeacon);
|
|
|
|
*isCalDone = AH_TRUE;
|
|
|
|
return AH_TRUE;
|
|
}
|
|
|
|
HAL_BOOL
|
|
ar5210PerCalibration(struct ath_hal *ah, struct ieee80211_channel *chan,
|
|
HAL_BOOL *isIQdone)
|
|
{
|
|
return ar5210PerCalibrationN(ah, chan, 0x1, AH_TRUE, isIQdone);
|
|
}
|
|
|
|
HAL_BOOL
|
|
ar5210ResetCalValid(struct ath_hal *ah, const struct ieee80211_channel *chan)
|
|
{
|
|
return AH_TRUE;
|
|
}
|
|
|
|
/*
|
|
* Writes the given reset bit mask into the reset register
|
|
*/
|
|
static HAL_BOOL
|
|
ar5210SetResetReg(struct ath_hal *ah, uint32_t resetMask, u_int delay)
|
|
{
|
|
uint32_t mask = resetMask ? resetMask : ~0;
|
|
HAL_BOOL rt;
|
|
|
|
OS_REG_WRITE(ah, AR_RC, resetMask);
|
|
/* need to wait at least 128 clocks when reseting PCI before read */
|
|
OS_DELAY(delay);
|
|
|
|
resetMask &= AR_RC_RPCU | AR_RC_RDMA | AR_RC_RPHY | AR_RC_RMAC;
|
|
mask &= AR_RC_RPCU | AR_RC_RDMA | AR_RC_RPHY | AR_RC_RMAC;
|
|
rt = ath_hal_wait(ah, AR_RC, mask, resetMask);
|
|
if ((resetMask & AR_RC_RMAC) == 0) {
|
|
if (isBigEndian()) {
|
|
/*
|
|
* Set CFG, little-endian for descriptor accesses.
|
|
*/
|
|
mask = INIT_CONFIG_STATUS | AR_CFG_SWTD | AR_CFG_SWRD;
|
|
OS_REG_WRITE(ah, AR_CFG, mask);
|
|
} else
|
|
OS_REG_WRITE(ah, AR_CFG, INIT_CONFIG_STATUS);
|
|
}
|
|
return rt;
|
|
}
|
|
|
|
|
|
/*
|
|
* Returns: the pcdac value
|
|
*/
|
|
static uint8_t
|
|
getPcdac(struct ath_hal *ah, const struct tpcMap *pRD, uint8_t dBm)
|
|
{
|
|
int32_t i;
|
|
int useNextEntry = AH_FALSE;
|
|
uint32_t interp;
|
|
|
|
for (i = AR_TP_SCALING_ENTRIES - 1; i >= 0; i--) {
|
|
/* Check for exact entry */
|
|
if (dBm == AR_I2DBM(i)) {
|
|
if (pRD->pcdac[i] != 63)
|
|
return pRD->pcdac[i];
|
|
useNextEntry = AH_TRUE;
|
|
} else if (dBm + 1 == AR_I2DBM(i) && i > 0) {
|
|
/* Interpolate for between entry with a logish scale */
|
|
if (pRD->pcdac[i] != 63 && pRD->pcdac[i-1] != 63) {
|
|
interp = (350 * (pRD->pcdac[i] - pRD->pcdac[i-1])) + 999;
|
|
interp = (interp / 1000) + pRD->pcdac[i-1];
|
|
return interp;
|
|
}
|
|
useNextEntry = AH_TRUE;
|
|
} else if (useNextEntry == AH_TRUE) {
|
|
/* Grab the next lowest */
|
|
if (pRD->pcdac[i] != 63)
|
|
return pRD->pcdac[i];
|
|
}
|
|
}
|
|
|
|
/* Return the lowest Entry if we haven't returned */
|
|
for (i = 0; i < AR_TP_SCALING_ENTRIES; i++)
|
|
if (pRD->pcdac[i] != 63)
|
|
return pRD->pcdac[i];
|
|
|
|
/* No value to return from table */
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah, "%s: empty transmit power table?\n", __func__);
|
|
#endif
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* Find or interpolates the gainF value from the table ptr.
|
|
*/
|
|
static uint8_t
|
|
getGainF(struct ath_hal *ah, const struct tpcMap *pRD,
|
|
uint8_t pcdac, uint8_t *dBm)
|
|
{
|
|
uint32_t interp;
|
|
int low, high, i;
|
|
|
|
low = high = -1;
|
|
|
|
for (i = 0; i < AR_TP_SCALING_ENTRIES; i++) {
|
|
if(pRD->pcdac[i] == 63)
|
|
continue;
|
|
if (pcdac == pRD->pcdac[i]) {
|
|
*dBm = AR_I2DBM(i);
|
|
return pRD->gainF[i]; /* Exact Match */
|
|
}
|
|
if (pcdac > pRD->pcdac[i])
|
|
low = i;
|
|
if (pcdac < pRD->pcdac[i]) {
|
|
high = i;
|
|
if (low == -1) {
|
|
*dBm = AR_I2DBM(i);
|
|
/* PCDAC is lower than lowest setting */
|
|
return pRD->gainF[i];
|
|
}
|
|
break;
|
|
}
|
|
}
|
|
if (i >= AR_TP_SCALING_ENTRIES && low == -1) {
|
|
/* No settings were found */
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah,
|
|
"%s: no valid entries in the pcdac table: %d\n",
|
|
__func__, pcdac);
|
|
#endif
|
|
return 63;
|
|
}
|
|
if (i >= AR_TP_SCALING_ENTRIES) {
|
|
/* PCDAC setting was above the max setting in the table */
|
|
*dBm = AR_I2DBM(low);
|
|
return pRD->gainF[low];
|
|
}
|
|
/* Only exact if table has no missing entries */
|
|
*dBm = (low + high) + 3;
|
|
|
|
/*
|
|
* Perform interpolation between low and high values to find gainF
|
|
* linearly scale the pcdac between low and high
|
|
*/
|
|
interp = ((pcdac - pRD->pcdac[low]) * 1000) /
|
|
(pRD->pcdac[high] - pRD->pcdac[low]);
|
|
/*
|
|
* Multiply the scale ratio by the gainF difference
|
|
* (plus a rnd up factor)
|
|
*/
|
|
interp = ((interp * (pRD->gainF[high] - pRD->gainF[low])) + 999) / 1000;
|
|
|
|
/* Add ratioed gain_f to low gain_f value */
|
|
return interp + pRD->gainF[low];
|
|
}
|
|
|
|
HAL_BOOL
|
|
ar5210SetTxPowerLimit(struct ath_hal *ah, uint32_t limit)
|
|
{
|
|
AH_PRIVATE(ah)->ah_powerLimit = AH_MIN(limit, AR5210_MAX_RATE_POWER);
|
|
/* XXX flush to h/w */
|
|
return AH_TRUE;
|
|
}
|
|
|
|
/*
|
|
* Get TXPower values and set them in the radio
|
|
*/
|
|
static HAL_BOOL
|
|
setupPowerSettings(struct ath_hal *ah, const struct ieee80211_channel *chan,
|
|
uint8_t cp[17])
|
|
{
|
|
uint16_t freq = ath_hal_gethwchannel(ah, chan);
|
|
const HAL_EEPROM_v1 *ee = AH_PRIVATE(ah)->ah_eeprom;
|
|
uint8_t gainFRD, gainF36, gainF48, gainF54;
|
|
uint8_t dBmRD, dBm36, dBm48, dBm54, dontcare;
|
|
uint32_t rd, group;
|
|
const struct tpcMap *pRD;
|
|
|
|
/* Set OB/DB Values regardless of channel */
|
|
cp[15] = (ee->ee_biasCurrents >> 4) & 0x7;
|
|
cp[16] = ee->ee_biasCurrents & 0x7;
|
|
|
|
if (freq < 5170 || freq > 5320) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: invalid channel %u\n",
|
|
__func__, freq);
|
|
return AH_FALSE;
|
|
}
|
|
|
|
HALASSERT(ee->ee_version >= AR_EEPROM_VER1 &&
|
|
ee->ee_version < AR_EEPROM_VER3);
|
|
|
|
/* Match regulatory domain */
|
|
for (rd = 0; rd < AR_REG_DOMAINS_MAX; rd++)
|
|
if (AH_PRIVATE(ah)->ah_currentRD == ee->ee_regDomain[rd])
|
|
break;
|
|
if (rd == AR_REG_DOMAINS_MAX) {
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah,
|
|
"%s: no calibrated regulatory domain matches the "
|
|
"current regularly domain (0x%0x)\n", __func__,
|
|
AH_PRIVATE(ah)->ah_currentRD);
|
|
#endif
|
|
return AH_FALSE;
|
|
}
|
|
group = ((freq - 5170) / 10);
|
|
|
|
if (group > 11) {
|
|
/* Pull 5.29 into the 5.27 group */
|
|
group--;
|
|
}
|
|
|
|
/* Integer divide will set group from 0 to 4 */
|
|
group = group / 3;
|
|
pRD = &ee->ee_tpc[group];
|
|
|
|
/* Set PC DAC Values */
|
|
cp[14] = pRD->regdmn[rd];
|
|
cp[9] = AH_MIN(pRD->regdmn[rd], pRD->rate36);
|
|
cp[8] = AH_MIN(pRD->regdmn[rd], pRD->rate48);
|
|
cp[7] = AH_MIN(pRD->regdmn[rd], pRD->rate54);
|
|
|
|
/* Find Corresponding gainF values for RD, 36, 48, 54 */
|
|
gainFRD = getGainF(ah, pRD, pRD->regdmn[rd], &dBmRD);
|
|
gainF36 = getGainF(ah, pRD, cp[9], &dBm36);
|
|
gainF48 = getGainF(ah, pRD, cp[8], &dBm48);
|
|
gainF54 = getGainF(ah, pRD, cp[7], &dBm54);
|
|
|
|
/* Power Scale if requested */
|
|
if (AH_PRIVATE(ah)->ah_tpScale != HAL_TP_SCALE_MAX) {
|
|
static const uint16_t tpcScaleReductionTable[5] =
|
|
{ 0, 3, 6, 9, AR5210_MAX_RATE_POWER };
|
|
uint16_t tpScale;
|
|
|
|
tpScale = tpcScaleReductionTable[AH_PRIVATE(ah)->ah_tpScale];
|
|
if (dBmRD < tpScale+3)
|
|
dBmRD = 3; /* min */
|
|
else
|
|
dBmRD -= tpScale;
|
|
cp[14] = getPcdac(ah, pRD, dBmRD);
|
|
gainFRD = getGainF(ah, pRD, cp[14], &dontcare);
|
|
dBm36 = AH_MIN(dBm36, dBmRD);
|
|
cp[9] = getPcdac(ah, pRD, dBm36);
|
|
gainF36 = getGainF(ah, pRD, cp[9], &dontcare);
|
|
dBm48 = AH_MIN(dBm48, dBmRD);
|
|
cp[8] = getPcdac(ah, pRD, dBm48);
|
|
gainF48 = getGainF(ah, pRD, cp[8], &dontcare);
|
|
dBm54 = AH_MIN(dBm54, dBmRD);
|
|
cp[7] = getPcdac(ah, pRD, dBm54);
|
|
gainF54 = getGainF(ah, pRD, cp[7], &dontcare);
|
|
}
|
|
/* Record current dBm at rate 6 */
|
|
AH_PRIVATE(ah)->ah_maxPowerLevel = 2*dBmRD;
|
|
|
|
cp[13] = cp[12] = cp[11] = cp[10] = cp[14];
|
|
|
|
/* Set GainF Values */
|
|
cp[0] = gainFRD - gainF54;
|
|
cp[1] = gainFRD - gainF48;
|
|
cp[2] = gainFRD - gainF36;
|
|
/* 9, 12, 18, 24 have no gain_delta from 6 */
|
|
cp[3] = cp[4] = cp[5] = cp[6] = 0;
|
|
return AH_TRUE;
|
|
}
|
|
|
|
/*
|
|
* Places the device in and out of reset and then places sane
|
|
* values in the registers based on EEPROM config, initialization
|
|
* vectors (as determined by the mode), and station configuration
|
|
*/
|
|
HAL_BOOL
|
|
ar5210SetTransmitPower(struct ath_hal *ah, const struct ieee80211_channel *chan)
|
|
{
|
|
#define N(a) (sizeof (a) / sizeof (a[0]))
|
|
static const uint32_t pwr_regs_start[17] = {
|
|
0x00000000, 0x00000000, 0x00000000,
|
|
0x00000000, 0x00000000, 0xf0000000,
|
|
0xcc000000, 0x00000000, 0x00000000,
|
|
0x00000000, 0x0a000000, 0x000000e2,
|
|
0x0a000020, 0x01000002, 0x01000018,
|
|
0x40000000, 0x00000418
|
|
};
|
|
uint16_t i;
|
|
uint8_t cp[sizeof(ar5k0007_pwrSettings)];
|
|
uint32_t pwr_regs[17];
|
|
|
|
OS_MEMCPY(pwr_regs, pwr_regs_start, sizeof(pwr_regs));
|
|
OS_MEMCPY(cp, ar5k0007_pwrSettings, sizeof(cp));
|
|
|
|
/* Check the EEPROM tx power calibration settings */
|
|
if (!setupPowerSettings(ah, chan, cp)) {
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah, "%s: unable to setup power settings\n",
|
|
__func__);
|
|
#endif
|
|
return AH_FALSE;
|
|
}
|
|
if (cp[15] < 1 || cp[15] > 5) {
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah, "%s: OB out of range (%u)\n",
|
|
__func__, cp[15]);
|
|
#endif
|
|
return AH_FALSE;
|
|
}
|
|
if (cp[16] < 1 || cp[16] > 5) {
|
|
#ifdef AH_DEBUG
|
|
ath_hal_printf(ah, "%s: DB out of range (%u)\n",
|
|
__func__, cp[16]);
|
|
#endif
|
|
return AH_FALSE;
|
|
}
|
|
|
|
/* reverse bits of the transmit power array */
|
|
for (i = 0; i < 7; i++)
|
|
cp[i] = ath_hal_reverseBits(cp[i], 5);
|
|
for (i = 7; i < 15; i++)
|
|
cp[i] = ath_hal_reverseBits(cp[i], 6);
|
|
|
|
/* merge transmit power values into the register - quite gross */
|
|
pwr_regs[0] |= ((cp[1] << 5) & 0xE0) | (cp[0] & 0x1F);
|
|
pwr_regs[1] |= ((cp[3] << 7) & 0x80) | ((cp[2] << 2) & 0x7C) |
|
|
((cp[1] >> 3) & 0x03);
|
|
pwr_regs[2] |= ((cp[4] << 4) & 0xF0) | ((cp[3] >> 1) & 0x0F);
|
|
pwr_regs[3] |= ((cp[6] << 6) & 0xC0) | ((cp[5] << 1) & 0x3E) |
|
|
((cp[4] >> 4) & 0x01);
|
|
pwr_regs[4] |= ((cp[7] << 3) & 0xF8) | ((cp[6] >> 2) & 0x07);
|
|
pwr_regs[5] |= ((cp[9] << 7) & 0x80) | ((cp[8] << 1) & 0x7E) |
|
|
((cp[7] >> 5) & 0x01);
|
|
pwr_regs[6] |= ((cp[10] << 5) & 0xE0) | ((cp[9] >> 1) & 0x1F);
|
|
pwr_regs[7] |= ((cp[11] << 3) & 0xF8) | ((cp[10] >> 3) & 0x07);
|
|
pwr_regs[8] |= ((cp[12] << 1) & 0x7E) | ((cp[11] >> 5) & 0x01);
|
|
pwr_regs[9] |= ((cp[13] << 5) & 0xE0);
|
|
pwr_regs[10] |= ((cp[14] << 3) & 0xF8) | ((cp[13] >> 3) & 0x07);
|
|
pwr_regs[11] |= ((cp[14] >> 5) & 0x01);
|
|
|
|
/* Set OB */
|
|
pwr_regs[8] |= (ath_hal_reverseBits(cp[15], 3) << 7) & 0x80;
|
|
pwr_regs[9] |= (ath_hal_reverseBits(cp[15], 3) >> 1) & 0x03;
|
|
|
|
/* Set DB */
|
|
pwr_regs[9] |= (ath_hal_reverseBits(cp[16], 3) << 2) & 0x1C;
|
|
|
|
/* Write the registers */
|
|
for (i = 0; i < N(pwr_regs)-1; i++)
|
|
OS_REG_WRITE(ah, 0x0000989c, pwr_regs[i]);
|
|
/* last write is a flush */
|
|
OS_REG_WRITE(ah, 0x000098d4, pwr_regs[i]);
|
|
|
|
return AH_TRUE;
|
|
#undef N
|
|
}
|
|
|
|
/*
|
|
* Takes the MHz channel value and sets the Channel value
|
|
*
|
|
* ASSUMES: Writes enabled to analog bus before AGC is active
|
|
* or by disabling the AGC.
|
|
*/
|
|
static HAL_BOOL
|
|
ar5210SetChannel(struct ath_hal *ah, struct ieee80211_channel *chan)
|
|
{
|
|
uint16_t freq = ath_hal_gethwchannel(ah, chan);
|
|
uint32_t data;
|
|
|
|
/* Set the Channel */
|
|
data = ath_hal_reverseBits((freq - 5120)/10, 5);
|
|
data = (data << 1) | 0x41;
|
|
OS_REG_WRITE(ah, AR_PHY(0x27), data);
|
|
OS_REG_WRITE(ah, AR_PHY(0x30), 0);
|
|
AH_PRIVATE(ah)->ah_curchan = chan;
|
|
return AH_TRUE;
|
|
}
|
|
|
|
int16_t
|
|
ar5210GetNoiseFloor(struct ath_hal *ah)
|
|
{
|
|
int16_t nf;
|
|
|
|
nf = (OS_REG_READ(ah, AR_PHY(25)) >> 19) & 0x1ff;
|
|
if (nf & 0x100)
|
|
nf = 0 - ((nf ^ 0x1ff) + 1);
|
|
return nf;
|
|
}
|
|
|
|
#define NORMAL_NF_THRESH (-72)
|
|
/*
|
|
* Peform the noisefloor calibration and check for
|
|
* any constant channel interference
|
|
*
|
|
* Returns: TRUE for a successful noise floor calibration; else FALSE
|
|
*/
|
|
HAL_BOOL
|
|
ar5210CalNoiseFloor(struct ath_hal *ah, HAL_CHANNEL_INTERNAL *ichan)
|
|
{
|
|
int32_t nf, nfLoops;
|
|
|
|
/* Calibrate the noise floor */
|
|
OS_REG_WRITE(ah, AR_PHY_AGCCTL,
|
|
OS_REG_READ(ah, AR_PHY_AGCCTL) | AR_PHY_AGC_NF);
|
|
|
|
/* Do not read noise floor until it has done the first update */
|
|
if (!ath_hal_wait(ah, AR_PHY_AGCCTL, AR_PHY_AGC_NF, 0)) {
|
|
#ifdef ATH_HAL_DEBUG
|
|
ath_hal_printf(ah, " -PHY NF Reg state: 0x%x\n",
|
|
OS_REG_READ(ah, AR_PHY_AGCCTL));
|
|
ath_hal_printf(ah, " -MAC Reset Reg state: 0x%x\n",
|
|
OS_REG_READ(ah, AR_RC));
|
|
ath_hal_printf(ah, " -PHY Active Reg state: 0x%x\n",
|
|
OS_REG_READ(ah, AR_PHY_ACTIVE));
|
|
#endif /* ATH_HAL_DEBUG */
|
|
return AH_FALSE;
|
|
}
|
|
|
|
nf = 0;
|
|
/* Keep checking until the floor is below the threshold or the nf is done */
|
|
for (nfLoops = 0; ((nfLoops < 21) && (nf > NORMAL_NF_THRESH)); nfLoops++) {
|
|
OS_DELAY(1000); /* Sleep for 1 ms */
|
|
nf = ar5210GetNoiseFloor(ah);
|
|
}
|
|
|
|
if (nf > NORMAL_NF_THRESH) {
|
|
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: Bad noise cal %d\n",
|
|
__func__, nf);
|
|
ichan->rawNoiseFloor = 0;
|
|
return AH_FALSE;
|
|
}
|
|
ichan->rawNoiseFloor = nf;
|
|
return AH_TRUE;
|
|
}
|
|
|
|
/*
|
|
* Adjust NF based on statistical values for 5GHz frequencies.
|
|
*/
|
|
int16_t
|
|
ar5210GetNfAdjust(struct ath_hal *ah, const HAL_CHANNEL_INTERNAL *c)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
HAL_RFGAIN
|
|
ar5210GetRfgain(struct ath_hal *ah)
|
|
{
|
|
return HAL_RFGAIN_INACTIVE;
|
|
}
|