a1b2c20925
o Sorted includes and added missing header files. o Added basic endianness support. In theory ste(4) should work on any architectures. o Remove the use of contigmalloc(9), contigfree(9) and vtophys(9). o Added 8 byte alignment limitation of TX/RX descriptor. o Added 1 byte alignment requirement for TX/RX buffers. o ste(4) controllers does not support DAC. Limit DMA address space to be within 32bit address. o Added spare DMA map to gracefully recover from DMA map failure. o Removed dead code for checking STE_RXSTAT_DMADONE bit. The bit was already checked in each iteration of loop so it can't be true. o Added second argument count to ste_rxeof(). It is used to limit number of iterations done in RX handler. ATM polling is the only consumer. o Removed ste_rxeoc() which was added to address RX stuck issue (cvs rev 1.66). Unlike TX descriptors, ST201 supports chaining descriptors to form a ring for RX descriptors. If RX descriptor chaining is not supported it's possible for controller to stop receiving incoming frames once controller pass the end of RX descriptor which in turn requires driver post new RX descriptors to receive more frames. For TX descriptors which does not support chaning, we exactly do manual chaining in driver by concatenating new descriptors to the end of previous TX chain. Maybe the workaround was borrowed from other drivers that does not support RX descriptor chaining, which is not valid for ST201 controllers. I still have no idea how this address RX stuck issue and I can't reproduce the RX stuck issue on DFE-550TX controller. o Removed hw.ste_rxsyncs sysctl as the workaround was removed. o TX/RX side bus_dmamap_load_mbuf_sg(9) support. o Reimplemented optimized ste_encap(). o Simplified TX logic of ste_start_locked(). o Added comments for TFD/RFD requirements. o Increased number of RX descriptors to 128 from 64. 128 gave much better performance than 64 under high network loads.
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html