470 lines
11 KiB
Plaintext
470 lines
11 KiB
Plaintext
/*
|
|
* Device Tree file for D-Link DIR-685 Xtreme N Storage Router
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "gemini.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "D-Link DIR-685 Xtreme N Storage Router";
|
|
compatible = "dlink,dir-685", "cortina,gemini";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory@0 {
|
|
/* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait consoleblank=300";
|
|
stdout-path = "uart0:19200n8";
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
|
|
button-esc {
|
|
debounce-interval = <100>;
|
|
wakeup-source;
|
|
linux,code = <KEY_ESC>;
|
|
label = "reset";
|
|
/* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
button-eject {
|
|
debounce-interval = <100>;
|
|
wakeup-source;
|
|
linux,code = <KEY_EJECTCD>;
|
|
label = "unmount";
|
|
/* Collides with LPC LFRAME, UART RTS, SSP TXD */
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
vdisp: regulator {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "display-power";
|
|
regulator-min-microvolt = <3600000>;
|
|
regulator-max-microvolt = <3600000>;
|
|
/* Collides with LCD E */
|
|
gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
/* Collides with IDE pins, that's cool (we do not use them) */
|
|
gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
|
gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
|
gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
|
|
num-chipselects = <1>;
|
|
|
|
panel: display@0 {
|
|
compatible = "dlink,dir-685-panel", "ilitek,ili9322";
|
|
reg = <0>;
|
|
/* 50 ns min period = 20 MHz */
|
|
spi-max-frequency = <20000000>;
|
|
vcc-supply = <&vdisp>;
|
|
iovcc-supply = <&vdisp>;
|
|
vci-supply = <&vdisp>;
|
|
|
|
port {
|
|
panel_in: endpoint {
|
|
remote-endpoint = <&display_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led-wps {
|
|
label = "dir685:blue:WPS";
|
|
/* Collides with ICE */
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
/*
|
|
* These two LEDs are on the side of the device.
|
|
* For electrical reasons, both LEDs cannot be active
|
|
* at the same time so only blue or orange can be on at
|
|
* one time. Enabling both makes the LED go dark.
|
|
* The LEDs both sit inside the unmount button and the
|
|
* label on the case says "unmount".
|
|
*/
|
|
led-blue-hd {
|
|
label = "dir685:blue:HD";
|
|
/* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "disk-read";
|
|
};
|
|
led-orange-hd {
|
|
label = "dir685:orange:HD";
|
|
/* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "disk-write";
|
|
};
|
|
};
|
|
|
|
/*
|
|
* This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
|
|
* Since the platform has no temperature sensor, this is controlled
|
|
* from userspace by using the hard disks S.M.A.R.T. temperature
|
|
* sensor. It is turned on when the temperature exceeds 46 degrees
|
|
* and turned off when the temperatures goes below 41 degrees
|
|
* (celsius).
|
|
*/
|
|
gpio-fan {
|
|
compatible = "gpio-fan";
|
|
/* Collides with IDE */
|
|
gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
|
|
gpio-fan,speed-map = <0 0>, <10000 1>;
|
|
#cooling-cells = <2>;
|
|
};
|
|
|
|
/*
|
|
* The touchpad input is connected to a GPIO bit-banged
|
|
* I2C bus.
|
|
*/
|
|
gpio-i2c {
|
|
compatible = "i2c-gpio";
|
|
/* Collides with ICE */
|
|
sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
touchkeys@26 {
|
|
compatible = "dlink,dir685-touchkeys";
|
|
reg = <0x26>;
|
|
interrupt-parent = <&gpio0>;
|
|
/* Collides with NAND flash */
|
|
interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
|
|
};
|
|
};
|
|
|
|
/* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
|
|
switch {
|
|
compatible = "realtek,rtl8366rb";
|
|
/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
|
|
mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
|
|
mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
|
|
reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
|
realtek,disable-leds;
|
|
|
|
switch_intc: interrupt-controller {
|
|
/* GPIO 15 provides the interrupt */
|
|
interrupt-parent = <&gpio0>;
|
|
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
};
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan0";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan1";
|
|
phy-handle = <&phy1>;
|
|
};
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan2";
|
|
phy-handle = <&phy2>;
|
|
};
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan3";
|
|
phy-handle = <&phy3>;
|
|
};
|
|
port@4 {
|
|
reg = <4>;
|
|
label = "wan";
|
|
phy-handle = <&phy4>;
|
|
};
|
|
rtl8366rb_cpu_port: port@5 {
|
|
reg = <5>;
|
|
label = "cpu";
|
|
ethernet = <&gmac0>;
|
|
phy-mode = "rgmii";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
|
|
};
|
|
|
|
mdio {
|
|
compatible = "realtek,smi-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: phy@0 {
|
|
reg = <0>;
|
|
interrupt-parent = <&switch_intc>;
|
|
interrupts = <0>;
|
|
};
|
|
phy1: phy@1 {
|
|
reg = <1>;
|
|
interrupt-parent = <&switch_intc>;
|
|
interrupts = <1>;
|
|
};
|
|
phy2: phy@2 {
|
|
reg = <2>;
|
|
interrupt-parent = <&switch_intc>;
|
|
interrupts = <2>;
|
|
};
|
|
phy3: phy@3 {
|
|
reg = <3>;
|
|
interrupt-parent = <&switch_intc>;
|
|
interrupts = <3>;
|
|
};
|
|
phy4: phy@4 {
|
|
reg = <4>;
|
|
interrupt-parent = <&switch_intc>;
|
|
interrupts = <12>;
|
|
};
|
|
};
|
|
};
|
|
|
|
soc {
|
|
flash@30000000 {
|
|
/*
|
|
* Flash access collides with the Chip Enable signal for
|
|
* the display panel, that reuse the parallel flash Chip
|
|
* Select 1 (CS1). We switch the pin control state so we
|
|
* enable these pins for flash access only when we need
|
|
* then, and when disabled they can be used for GPIO which
|
|
* is what the display panel needs.
|
|
*/
|
|
status = "okay";
|
|
pinctrl-names = "enabled", "disabled";
|
|
pinctrl-0 = <&pflash_default_pins>;
|
|
pinctrl-1 = <&pflash_disabled_pins>;
|
|
|
|
/* 32MB of flash */
|
|
reg = <0x30000000 0x02000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/*
|
|
* This "RedBoot" is the Storlink derivative.
|
|
*/
|
|
partition@0 {
|
|
label = "RedBoot";
|
|
reg = <0x00000000 0x00040000>;
|
|
read-only;
|
|
};
|
|
/*
|
|
* This firmware image contains the kernel catenated
|
|
* with the squashfs root filesystem. For some reason
|
|
* this is called "upgrade" on the vendor system.
|
|
*/
|
|
partition@40000 {
|
|
label = "upgrade";
|
|
reg = <0x00040000 0x01f40000>;
|
|
read-only;
|
|
};
|
|
/* RGDB, Residental Gateway Database? */
|
|
partition@1f80000 {
|
|
label = "rgdb";
|
|
reg = <0x01f80000 0x00040000>;
|
|
read-only;
|
|
};
|
|
/*
|
|
* This partition contains MAC addresses for WAN,
|
|
* WLAN and LAN, and the country code (for wireless
|
|
* I guess).
|
|
*/
|
|
partition@1fc0000 {
|
|
label = "nvram";
|
|
reg = <0x01fc0000 0x00020000>;
|
|
read-only;
|
|
};
|
|
partition@1fe0000 {
|
|
label = "LangPack";
|
|
reg = <0x01fe0000 0x00020000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
syscon: syscon@40000000 {
|
|
pinctrl {
|
|
/*
|
|
* gpio0bgrp cover line 5, 6 used by TK I2C
|
|
* gpio0bgrp cover line 7 used by WPS LED
|
|
* gpio0cgrp cover line 8, 13 used by keys
|
|
* and 11, 12 used by the HD LEDs
|
|
* and line 14, 15 used by RTL8366
|
|
* RESET and phy ready
|
|
* gpio0egrp cover line 16 used by VDISP
|
|
* gpio0fgrp cover line 17 used by TK IRQ
|
|
* gpio0ggrp cover line 20 used by panel CS
|
|
* gpio0hgrp cover line 21,22 used by RTL8366RB MDIO
|
|
*/
|
|
gpio0_default_pins: pinctrl-gpio0 {
|
|
mux {
|
|
function = "gpio0";
|
|
groups = "gpio0bgrp",
|
|
"gpio0cgrp",
|
|
"gpio0egrp",
|
|
"gpio0fgrp",
|
|
"gpio0hgrp";
|
|
};
|
|
};
|
|
/*
|
|
* gpio1bgrp cover line 5,8,7 used by panel SPI
|
|
* also line 6 used by the fan
|
|
*
|
|
*/
|
|
gpio1_default_pins: pinctrl-gpio1 {
|
|
mux {
|
|
function = "gpio1";
|
|
groups = "gpio1bgrp";
|
|
};
|
|
};
|
|
/*
|
|
* These GPIO groups will be mapped in over some
|
|
* of the flash pins when the flash is not in
|
|
* active use.
|
|
*/
|
|
pflash_disabled_pins: pinctrl-pflash-disabled {
|
|
mux {
|
|
function = "gpio0";
|
|
groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
|
|
"gpio0kgrp";
|
|
};
|
|
};
|
|
pinctrl-gmii {
|
|
mux {
|
|
function = "gmii";
|
|
groups = "gmii_gmac0_grp";
|
|
};
|
|
conf0 {
|
|
pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV",
|
|
"Y7 GMAC0 RXC", "Y11 GMAC1 RXC",
|
|
"T8 GMAC0 TXEN", "W11 GMAC1 TXEN",
|
|
"U8 GMAC0 TXC", "V11 GMAC1 TXC",
|
|
"W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
|
|
"Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
|
|
"T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
|
|
"V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
|
|
"Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
|
|
"T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
|
|
"U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
|
|
"W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
|
|
skew-delay = <7>;
|
|
};
|
|
/* Set up drive strength on GMAC0 to 16 mA */
|
|
conf1 {
|
|
groups = "gmii_gmac0_grp";
|
|
drive-strength = <16>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sata: sata@46000000 {
|
|
cortina,gemini-ata-muxmode = <0>;
|
|
cortina,gemini-enable-sata-bridge;
|
|
status = "okay";
|
|
};
|
|
|
|
gpio0: gpio@4d000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio0_default_pins>;
|
|
};
|
|
|
|
gpio1: gpio@4e000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio1_default_pins>;
|
|
};
|
|
|
|
pci@50000000 {
|
|
status = "okay";
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
|
|
<0x4800 0 0 2 &pci_intc 1>,
|
|
<0x4800 0 0 3 &pci_intc 2>,
|
|
<0x4800 0 0 4 &pci_intc 3>,
|
|
<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
|
|
<0x5000 0 0 2 &pci_intc 2>,
|
|
<0x5000 0 0 3 &pci_intc 3>,
|
|
<0x5000 0 0 4 &pci_intc 0>,
|
|
<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
|
|
<0x5800 0 0 2 &pci_intc 3>,
|
|
<0x5800 0 0 3 &pci_intc 0>,
|
|
<0x5800 0 0 4 &pci_intc 1>,
|
|
<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
|
|
<0x6000 0 0 2 &pci_intc 0>,
|
|
<0x6000 0 0 3 &pci_intc 1>,
|
|
<0x6000 0 0 4 &pci_intc 2>;
|
|
};
|
|
|
|
ethernet@60000000 {
|
|
status = "okay";
|
|
|
|
ethernet-port@0 {
|
|
phy-mode = "rgmii";
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
ethernet-port@1 {
|
|
/* Not used in this platform */
|
|
};
|
|
};
|
|
|
|
ata@63000000 {
|
|
status = "okay";
|
|
};
|
|
|
|
display-controller@6a000000 {
|
|
status = "okay";
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
display_out: endpoint {
|
|
remote-endpoint = <&panel_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
usb@68000000 {
|
|
status = "okay";
|
|
};
|
|
|
|
usb@69000000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|