be4aa869c1
14.00.00.01-fbsd. Their description of the changes is as follows: 1. Copyright contents has been changed in all respective .c and .h files 2. Support for WRITE12 and READ12 for direct-io (warpdrive only) has been added. 3. Driver has added checks to see if Drive has READ_CAP_16 support before sending it down to the device. If SPC3_SID_PROTECT flag is set in the inquiry data, the device supports protection information, and must support the 16 byte read capacity command, otherwise continue without sending read cap 16. This will optimize driver performance, since it will not send READ_CAP_16 to the drive which does not have support of READ_CAP_16. 4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not use DELAY() which is busy loop implementation. It will use <msleep> (Better way to sleep without busy loop). Also from the HBA reset code path and some other places, DELAY() is replaced with msleep() or "pause()", which is based on sleep/wakeup style calls. Driver use msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP flags to avoid busy loop which is not required all the time.e.a a. While driver is getting loaded, driver calls most of the commands with NO_SLEEP. b. When Driver is functional and it needs Reinit of HBA, CAN_SLEEP flag is used. 5. <mpslsi> driver is not Endian safe. It will not work on Big Endian machines like Sparc and PowerPC platforms because it assumes it is running on a Little Endian machine. Driver code is modified such way that it does not assume CPU arch is Little Endian. a. All places where Driver interacts from HBA to Host, it converts Little Endian format to CPU format. b. All places where Driver interacts from Host to HBA, it converts CPU format to Little Endian. 6. Findout memory leaks in FreeBSD Driver and resolve those, such as memory leak in targ's luns creation/deletion. Also added additional checks to see memory allocation success/fail. 7. Add loginfo prints as debug message, i.e. When FW sends any loginfo, Driver should print those as debug message. This will help for debugging purpose. 8. There is possibility to get config request timeout. Current driver is able to detect config request timetout, but it does not do anything on config_request timeout. Driver should call mps_reinit() if any request_poll (which is called as part of config_request) is time out. 9. cdb length check is required for 32 byte CDB. Add correct mpi control value for 32 bit CDB as below while submitting SCSI IO Request to controller. mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT; 10. Check the actual status of Message unit reset (mps_message_unit_reset).Previously FreeBSD Driver just writes MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack (it just wait for 50 millisecond). So, Driver now check the status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing it to the FW. Now it also checking for whether doorbell ack uses msleep with proper sleep flags, instead of <DELAY>. 11. Previously CAM does not detect Multi-Lun Devices. In order to detect Multi-Lun Devices by CAM the driver needs following change set: a. There is "max_lun" field which Driver need to set based on hw/fw support. Currently LSI released driver does not set this field. b. Default of "max_lun" should not be 0 in OS, but it is currently set to 0 in CAM layer. c. Export max_lun capacity to 255 12. Driver will not reset target info after port enable complete and also do Device removal when Device remove from FW. The detail description is as follows a. When Driver receive WD PD add events, it will add all information in driver local data structure. b. Only for WD, we have below checks after port enable completes, where driver clear off all information retrieved at #1. if ((sc->WD_available && (sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) || (sc->WD_valid_config && (sc->WD_hide_expose == MPS_WD_HIDE_IF_VOLUME)) { // clear off target data structure. } It is mainly not to attach PDs to OS. FreeBSD does bus rescan as older Parallel scsi style. So Driver needs to handle which Drive is visible to OS. That is a reason we have to clear off targ information for PDs. Again, above logic was implemented long time ago. Similar concept we have for non-wd also. For that, LSI have introduced different logic to hide PDs. Eventually, because of above gap, when Phy goes offline, we observe below failure. That is what Driver is not doing complete removal of device with FW. (which was pointed by Scott) Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe Now Driver will not reset target info after port enable complete and also will do Device removal when Device remove from FW. 13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID" error code on request to the Target IDs that have no devices conected at that moment. As if "CAM_TID_INVALID" error code is returned to the CAM Layaer then it results in a huge chain of errors in verbose kernel messages on boot and every hot-plug event. Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com> MFC after: 3 days
2888 lines
139 KiB
C
2888 lines
139 KiB
C
/*-
|
|
* Copyright (c) 2011, 2012 LSI Corp.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* LSI MPT-Fusion Host Adapter FreeBSD
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
/*
|
|
* Copyright (c) 2000-2012 LSI Corporation.
|
|
*
|
|
*
|
|
* Name: mpi2_cnfg.h
|
|
* Title: MPI Configuration messages and pages
|
|
* Creation Date: November 10, 2006
|
|
*
|
|
* mpi2_cnfg.h Version: 02.00.17
|
|
*
|
|
* Version History
|
|
* ---------------
|
|
*
|
|
* Date Version Description
|
|
* -------- -------- ------------------------------------------------------
|
|
* 04-30-07 02.00.00 Corresponds to Fusion-MPT MPI Specification Rev A.
|
|
* 06-04-07 02.00.01 Added defines for SAS IO Unit Page 2 PhyFlags.
|
|
* Added Manufacturing Page 11.
|
|
* Added MPI2_SAS_EXPANDER0_FLAGS_CONNECTOR_END_DEVICE
|
|
* define.
|
|
* 06-26-07 02.00.02 Adding generic structure for product-specific
|
|
* Manufacturing pages: MPI2_CONFIG_PAGE_MANUFACTURING_PS.
|
|
* Rework of BIOS Page 2 configuration page.
|
|
* Fixed MPI2_BIOSPAGE2_BOOT_DEVICE to be a union of the
|
|
* forms.
|
|
* Added configuration pages IOC Page 8 and Driver
|
|
* Persistent Mapping Page 0.
|
|
* 08-31-07 02.00.03 Modified configuration pages dealing with Integrated
|
|
* RAID (Manufacturing Page 4, RAID Volume Pages 0 and 1,
|
|
* RAID Physical Disk Pages 0 and 1, RAID Configuration
|
|
* Page 0).
|
|
* Added new value for AccessStatus field of SAS Device
|
|
* Page 0 (_SATA_NEEDS_INITIALIZATION).
|
|
* 10-31-07 02.00.04 Added missing SEPDevHandle field to
|
|
* MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0.
|
|
* 12-18-07 02.00.05 Modified IO Unit Page 0 to use 32-bit version fields for
|
|
* NVDATA.
|
|
* Modified IOC Page 7 to use masks and added field for
|
|
* SASBroadcastPrimitiveMasks.
|
|
* Added MPI2_CONFIG_PAGE_BIOS_4.
|
|
* Added MPI2_CONFIG_PAGE_LOG_0.
|
|
* 02-29-08 02.00.06 Modified various names to make them 32-character unique.
|
|
* Added SAS Device IDs.
|
|
* Updated Integrated RAID configuration pages including
|
|
* Manufacturing Page 4, IOC Page 6, and RAID Configuration
|
|
* Page 0.
|
|
* 05-21-08 02.00.07 Added define MPI2_MANPAGE4_MIX_SSD_SAS_SATA.
|
|
* Added define MPI2_MANPAGE4_PHYSDISK_128MB_COERCION.
|
|
* Fixed define MPI2_IOCPAGE8_FLAGS_ENCLOSURE_SLOT_MAPPING.
|
|
* Added missing MaxNumRoutedSasAddresses field to
|
|
* MPI2_CONFIG_PAGE_EXPANDER_0.
|
|
* Added SAS Port Page 0.
|
|
* Modified structure layout for
|
|
* MPI2_CONFIG_PAGE_DRIVER_MAPPING_0.
|
|
* 06-27-08 02.00.08 Changed MPI2_CONFIG_PAGE_RD_PDISK_1 to use
|
|
* MPI2_RAID_PHYS_DISK1_PATH_MAX to size the array.
|
|
* 10-02-08 02.00.09 Changed MPI2_RAID_PGAD_CONFIGNUM_MASK from 0x0000FFFF
|
|
* to 0x000000FF.
|
|
* Added two new values for the Physical Disk Coercion Size
|
|
* bits in the Flags field of Manufacturing Page 4.
|
|
* Added product-specific Manufacturing pages 16 to 31.
|
|
* Modified Flags bits for controlling write cache on SATA
|
|
* drives in IO Unit Page 1.
|
|
* Added new bit to AdditionalControlFlags of SAS IO Unit
|
|
* Page 1 to control Invalid Topology Correction.
|
|
* Added additional defines for RAID Volume Page 0
|
|
* VolumeStatusFlags field.
|
|
* Modified meaning of RAID Volume Page 0 VolumeSettings
|
|
* define for auto-configure of hot-swap drives.
|
|
* Added SupportedPhysDisks field to RAID Volume Page 1 and
|
|
* added related defines.
|
|
* Added PhysDiskAttributes field (and related defines) to
|
|
* RAID Physical Disk Page 0.
|
|
* Added MPI2_SAS_PHYINFO_PHY_VACANT define.
|
|
* Added three new DiscoveryStatus bits for SAS IO Unit
|
|
* Page 0 and SAS Expander Page 0.
|
|
* Removed multiplexing information from SAS IO Unit pages.
|
|
* Added BootDeviceWaitTime field to SAS IO Unit Page 4.
|
|
* Removed Zone Address Resolved bit from PhyInfo and from
|
|
* Expander Page 0 Flags field.
|
|
* Added two new AccessStatus values to SAS Device Page 0
|
|
* for indicating routing problems. Added 3 reserved words
|
|
* to this page.
|
|
* 01-19-09 02.00.10 Fixed defines for GPIOVal field of IO Unit Page 3.
|
|
* Inserted missing reserved field into structure for IOC
|
|
* Page 6.
|
|
* Added more pending task bits to RAID Volume Page 0
|
|
* VolumeStatusFlags defines.
|
|
* Added MPI2_PHYSDISK0_STATUS_FLAG_NOT_CERTIFIED define.
|
|
* Added a new DiscoveryStatus bit for SAS IO Unit Page 0
|
|
* and SAS Expander Page 0 to flag a downstream initiator
|
|
* when in simplified routing mode.
|
|
* Removed SATA Init Failure defines for DiscoveryStatus
|
|
* fields of SAS IO Unit Page 0 and SAS Expander Page 0.
|
|
* Added MPI2_SAS_DEVICE0_ASTATUS_DEVICE_BLOCKED define.
|
|
* Added PortGroups, DmaGroup, and ControlGroup fields to
|
|
* SAS Device Page 0.
|
|
* 05-06-09 02.00.11 Added structures and defines for IO Unit Page 5 and IO
|
|
* Unit Page 6.
|
|
* Added expander reduced functionality data to SAS
|
|
* Expander Page 0.
|
|
* Added SAS PHY Page 2 and SAS PHY Page 3.
|
|
* 07-30-09 02.00.12 Added IO Unit Page 7.
|
|
* Added new device ids.
|
|
* Added SAS IO Unit Page 5.
|
|
* Added partial and slumber power management capable flags
|
|
* to SAS Device Page 0 Flags field.
|
|
* Added PhyInfo defines for power condition.
|
|
* Added Ethernet configuration pages.
|
|
* 10-28-09 02.00.13 Added MPI2_IOUNITPAGE1_ENABLE_HOST_BASED_DISCOVERY.
|
|
* Added SAS PHY Page 4 structure and defines.
|
|
* 02-10-10 02.00.14 Modified the comments for the configuration page
|
|
* structures that contain an array of data. The host
|
|
* should use the "count" field in the page data (e.g. the
|
|
* NumPhys field) to determine the number of valid elements
|
|
* in the array.
|
|
* Added/modified some MPI2_MFGPAGE_DEVID_SAS defines.
|
|
* Added PowerManagementCapabilities to IO Unit Page 7.
|
|
* Added PortWidthModGroup field to
|
|
* MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS.
|
|
* Added MPI2_CONFIG_PAGE_SASIOUNIT_6 and related defines.
|
|
* Added MPI2_CONFIG_PAGE_SASIOUNIT_7 and related defines.
|
|
* Added MPI2_CONFIG_PAGE_SASIOUNIT_8 and related defines.
|
|
* 05-12-10 02.00.15 Added MPI2_RAIDVOL0_STATUS_FLAG_VOL_NOT_CONSISTENT
|
|
* define.
|
|
* Added MPI2_PHYSDISK0_INCOMPATIBLE_MEDIA_TYPE define.
|
|
* Added MPI2_SAS_NEG_LINK_RATE_UNSUPPORTED_PHY define.
|
|
* 08-11-10 02.00.16 Removed IO Unit Page 1 device path (multi-pathing)
|
|
* defines.
|
|
* 11-10-10 02.00.17 Added ReceptacleID field (replacing Reserved1) to
|
|
* MPI2_MANPAGE7_CONNECTOR_INFO and reworked defines for
|
|
* the Pinout field.
|
|
* Added BoardTemperature and BoardTemperatureUnits fields
|
|
* to MPI2_CONFIG_PAGE_IO_UNIT_7.
|
|
* Added MPI2_CONFIG_EXTPAGETYPE_EXT_MANUFACTURING define
|
|
* and MPI2_CONFIG_PAGE_EXT_MAN_PS structure.
|
|
* --------------------------------------------------------------------------
|
|
*/
|
|
|
|
#ifndef MPI2_CNFG_H
|
|
#define MPI2_CNFG_H
|
|
|
|
/*****************************************************************************
|
|
* Configuration Page Header and defines
|
|
*****************************************************************************/
|
|
|
|
/* Config Page Header */
|
|
typedef struct _MPI2_CONFIG_PAGE_HEADER
|
|
{
|
|
U8 PageVersion; /* 0x00 */
|
|
U8 PageLength; /* 0x01 */
|
|
U8 PageNumber; /* 0x02 */
|
|
U8 PageType; /* 0x03 */
|
|
} MPI2_CONFIG_PAGE_HEADER, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_HEADER,
|
|
Mpi2ConfigPageHeader_t, MPI2_POINTER pMpi2ConfigPageHeader_t;
|
|
|
|
typedef union _MPI2_CONFIG_PAGE_HEADER_UNION
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Struct;
|
|
U8 Bytes[4];
|
|
U16 Word16[2];
|
|
U32 Word32;
|
|
} MPI2_CONFIG_PAGE_HEADER_UNION, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_HEADER_UNION,
|
|
Mpi2ConfigPageHeaderUnion, MPI2_POINTER pMpi2ConfigPageHeaderUnion;
|
|
|
|
/* Extended Config Page Header */
|
|
typedef struct _MPI2_CONFIG_EXTENDED_PAGE_HEADER
|
|
{
|
|
U8 PageVersion; /* 0x00 */
|
|
U8 Reserved1; /* 0x01 */
|
|
U8 PageNumber; /* 0x02 */
|
|
U8 PageType; /* 0x03 */
|
|
U16 ExtPageLength; /* 0x04 */
|
|
U8 ExtPageType; /* 0x06 */
|
|
U8 Reserved2; /* 0x07 */
|
|
} MPI2_CONFIG_EXTENDED_PAGE_HEADER,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_EXTENDED_PAGE_HEADER,
|
|
Mpi2ConfigExtendedPageHeader_t, MPI2_POINTER pMpi2ConfigExtendedPageHeader_t;
|
|
|
|
typedef union _MPI2_CONFIG_EXT_PAGE_HEADER_UNION
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Struct;
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Ext;
|
|
U8 Bytes[8];
|
|
U16 Word16[4];
|
|
U32 Word32[2];
|
|
} MPI2_CONFIG_EXT_PAGE_HEADER_UNION, MPI2_POINTER PTR_MPI2_CONFIG_EXT_PAGE_HEADER_UNION,
|
|
Mpi2ConfigPageExtendedHeaderUnion, MPI2_POINTER pMpi2ConfigPageExtendedHeaderUnion;
|
|
|
|
|
|
/* PageType field values */
|
|
#define MPI2_CONFIG_PAGEATTR_READ_ONLY (0x00)
|
|
#define MPI2_CONFIG_PAGEATTR_CHANGEABLE (0x10)
|
|
#define MPI2_CONFIG_PAGEATTR_PERSISTENT (0x20)
|
|
#define MPI2_CONFIG_PAGEATTR_MASK (0xF0)
|
|
|
|
#define MPI2_CONFIG_PAGETYPE_IO_UNIT (0x00)
|
|
#define MPI2_CONFIG_PAGETYPE_IOC (0x01)
|
|
#define MPI2_CONFIG_PAGETYPE_BIOS (0x02)
|
|
#define MPI2_CONFIG_PAGETYPE_RAID_VOLUME (0x08)
|
|
#define MPI2_CONFIG_PAGETYPE_MANUFACTURING (0x09)
|
|
#define MPI2_CONFIG_PAGETYPE_RAID_PHYSDISK (0x0A)
|
|
#define MPI2_CONFIG_PAGETYPE_EXTENDED (0x0F)
|
|
#define MPI2_CONFIG_PAGETYPE_MASK (0x0F)
|
|
|
|
#define MPI2_CONFIG_TYPENUM_MASK (0x0FFF)
|
|
|
|
|
|
/* ExtPageType field values */
|
|
#define MPI2_CONFIG_EXTPAGETYPE_SAS_IO_UNIT (0x10)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_SAS_EXPANDER (0x11)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_SAS_DEVICE (0x12)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_SAS_PHY (0x13)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_LOG (0x14)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_ENCLOSURE (0x15)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_RAID_CONFIG (0x16)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_DRIVER_MAPPING (0x17)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_SAS_PORT (0x18)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_ETHERNET (0x19)
|
|
#define MPI2_CONFIG_EXTPAGETYPE_EXT_MANUFACTURING (0x1A)
|
|
|
|
|
|
/*****************************************************************************
|
|
* PageAddress defines
|
|
*****************************************************************************/
|
|
|
|
/* RAID Volume PageAddress format */
|
|
#define MPI2_RAID_VOLUME_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_RAID_VOLUME_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
|
|
#define MPI2_RAID_VOLUME_PGAD_FORM_HANDLE (0x10000000)
|
|
|
|
#define MPI2_RAID_VOLUME_PGAD_HANDLE_MASK (0x0000FFFF)
|
|
|
|
|
|
/* RAID Physical Disk PageAddress format */
|
|
#define MPI2_PHYSDISK_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_PHYSDISK_PGAD_FORM_GET_NEXT_PHYSDISKNUM (0x00000000)
|
|
#define MPI2_PHYSDISK_PGAD_FORM_PHYSDISKNUM (0x10000000)
|
|
#define MPI2_PHYSDISK_PGAD_FORM_DEVHANDLE (0x20000000)
|
|
|
|
#define MPI2_PHYSDISK_PGAD_PHYSDISKNUM_MASK (0x000000FF)
|
|
#define MPI2_PHYSDISK_PGAD_DEVHANDLE_MASK (0x0000FFFF)
|
|
|
|
|
|
/* SAS Expander PageAddress format */
|
|
#define MPI2_SAS_EXPAND_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_SAS_EXPAND_PGAD_FORM_GET_NEXT_HNDL (0x00000000)
|
|
#define MPI2_SAS_EXPAND_PGAD_FORM_HNDL_PHY_NUM (0x10000000)
|
|
#define MPI2_SAS_EXPAND_PGAD_FORM_HNDL (0x20000000)
|
|
|
|
#define MPI2_SAS_EXPAND_PGAD_HANDLE_MASK (0x0000FFFF)
|
|
#define MPI2_SAS_EXPAND_PGAD_PHYNUM_MASK (0x00FF0000)
|
|
#define MPI2_SAS_EXPAND_PGAD_PHYNUM_SHIFT (16)
|
|
|
|
|
|
/* SAS Device PageAddress format */
|
|
#define MPI2_SAS_DEVICE_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_SAS_DEVICE_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
|
|
#define MPI2_SAS_DEVICE_PGAD_FORM_HANDLE (0x20000000)
|
|
|
|
#define MPI2_SAS_DEVICE_PGAD_HANDLE_MASK (0x0000FFFF)
|
|
|
|
|
|
/* SAS PHY PageAddress format */
|
|
#define MPI2_SAS_PHY_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_SAS_PHY_PGAD_FORM_PHY_NUMBER (0x00000000)
|
|
#define MPI2_SAS_PHY_PGAD_FORM_PHY_TBL_INDEX (0x10000000)
|
|
|
|
#define MPI2_SAS_PHY_PGAD_PHY_NUMBER_MASK (0x000000FF)
|
|
#define MPI2_SAS_PHY_PGAD_PHY_TBL_INDEX_MASK (0x0000FFFF)
|
|
|
|
|
|
/* SAS Port PageAddress format */
|
|
#define MPI2_SASPORT_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_SASPORT_PGAD_FORM_GET_NEXT_PORT (0x00000000)
|
|
#define MPI2_SASPORT_PGAD_FORM_PORT_NUM (0x10000000)
|
|
|
|
#define MPI2_SASPORT_PGAD_PORTNUMBER_MASK (0x00000FFF)
|
|
|
|
|
|
/* SAS Enclosure PageAddress format */
|
|
#define MPI2_SAS_ENCLOS_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_SAS_ENCLOS_PGAD_FORM_GET_NEXT_HANDLE (0x00000000)
|
|
#define MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE (0x10000000)
|
|
|
|
#define MPI2_SAS_ENCLOS_PGAD_HANDLE_MASK (0x0000FFFF)
|
|
|
|
|
|
/* RAID Configuration PageAddress format */
|
|
#define MPI2_RAID_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM (0x00000000)
|
|
#define MPI2_RAID_PGAD_FORM_CONFIGNUM (0x10000000)
|
|
#define MPI2_RAID_PGAD_FORM_ACTIVE_CONFIG (0x20000000)
|
|
|
|
#define MPI2_RAID_PGAD_CONFIGNUM_MASK (0x000000FF)
|
|
|
|
|
|
/* Driver Persistent Mapping PageAddress format */
|
|
#define MPI2_DPM_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_DPM_PGAD_FORM_ENTRY_RANGE (0x00000000)
|
|
|
|
#define MPI2_DPM_PGAD_ENTRY_COUNT_MASK (0x0FFF0000)
|
|
#define MPI2_DPM_PGAD_ENTRY_COUNT_SHIFT (16)
|
|
#define MPI2_DPM_PGAD_START_ENTRY_MASK (0x0000FFFF)
|
|
|
|
|
|
/* Ethernet PageAddress format */
|
|
#define MPI2_ETHERNET_PGAD_FORM_MASK (0xF0000000)
|
|
#define MPI2_ETHERNET_PGAD_FORM_IF_NUM (0x00000000)
|
|
|
|
#define MPI2_ETHERNET_PGAD_IF_NUMBER_MASK (0x000000FF)
|
|
|
|
|
|
|
|
/****************************************************************************
|
|
* Configuration messages
|
|
****************************************************************************/
|
|
|
|
/* Configuration Request Message */
|
|
typedef struct _MPI2_CONFIG_REQUEST
|
|
{
|
|
U8 Action; /* 0x00 */
|
|
U8 SGLFlags; /* 0x01 */
|
|
U8 ChainOffset; /* 0x02 */
|
|
U8 Function; /* 0x03 */
|
|
U16 ExtPageLength; /* 0x04 */
|
|
U8 ExtPageType; /* 0x06 */
|
|
U8 MsgFlags; /* 0x07 */
|
|
U8 VP_ID; /* 0x08 */
|
|
U8 VF_ID; /* 0x09 */
|
|
U16 Reserved1; /* 0x0A */
|
|
U32 Reserved2; /* 0x0C */
|
|
U32 Reserved3; /* 0x10 */
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x14 */
|
|
U32 PageAddress; /* 0x18 */
|
|
MPI2_SGE_IO_UNION PageBufferSGE; /* 0x1C */
|
|
} MPI2_CONFIG_REQUEST, MPI2_POINTER PTR_MPI2_CONFIG_REQUEST,
|
|
Mpi2ConfigRequest_t, MPI2_POINTER pMpi2ConfigRequest_t;
|
|
|
|
/* values for the Action field */
|
|
#define MPI2_CONFIG_ACTION_PAGE_HEADER (0x00)
|
|
#define MPI2_CONFIG_ACTION_PAGE_READ_CURRENT (0x01)
|
|
#define MPI2_CONFIG_ACTION_PAGE_WRITE_CURRENT (0x02)
|
|
#define MPI2_CONFIG_ACTION_PAGE_DEFAULT (0x03)
|
|
#define MPI2_CONFIG_ACTION_PAGE_WRITE_NVRAM (0x04)
|
|
#define MPI2_CONFIG_ACTION_PAGE_READ_DEFAULT (0x05)
|
|
#define MPI2_CONFIG_ACTION_PAGE_READ_NVRAM (0x06)
|
|
#define MPI2_CONFIG_ACTION_PAGE_GET_CHANGEABLE (0x07)
|
|
|
|
/* use MPI2_SGLFLAGS_ defines from mpi2.h for the SGLFlags field */
|
|
|
|
|
|
/* Config Reply Message */
|
|
typedef struct _MPI2_CONFIG_REPLY
|
|
{
|
|
U8 Action; /* 0x00 */
|
|
U8 SGLFlags; /* 0x01 */
|
|
U8 MsgLength; /* 0x02 */
|
|
U8 Function; /* 0x03 */
|
|
U16 ExtPageLength; /* 0x04 */
|
|
U8 ExtPageType; /* 0x06 */
|
|
U8 MsgFlags; /* 0x07 */
|
|
U8 VP_ID; /* 0x08 */
|
|
U8 VF_ID; /* 0x09 */
|
|
U16 Reserved1; /* 0x0A */
|
|
U16 Reserved2; /* 0x0C */
|
|
U16 IOCStatus; /* 0x0E */
|
|
U32 IOCLogInfo; /* 0x10 */
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x14 */
|
|
} MPI2_CONFIG_REPLY, MPI2_POINTER PTR_MPI2_CONFIG_REPLY,
|
|
Mpi2ConfigReply_t, MPI2_POINTER pMpi2ConfigReply_t;
|
|
|
|
|
|
|
|
/*****************************************************************************
|
|
*
|
|
* C o n f i g u r a t i o n P a g e s
|
|
*
|
|
*****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Manufacturing Config pages
|
|
****************************************************************************/
|
|
|
|
#define MPI2_MFGPAGE_VENDORID_LSI (0x1000)
|
|
|
|
/* SAS */
|
|
#define MPI2_MFGPAGE_DEVID_SAS2004 (0x0070)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2008 (0x0072)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2108_1 (0x0074)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2108_2 (0x0076)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2108_3 (0x0077)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2116_1 (0x0064)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2116_2 (0x0065)
|
|
|
|
#define MPI2_MFGPAGE_DEVID_SSS6200 (0x007E)
|
|
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_1 (0x0080)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_2 (0x0081)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_3 (0x0082)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_4 (0x0083)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_5 (0x0084)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2208_6 (0x0085)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2308_1 (0x0086)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2308_2 (0x0087)
|
|
#define MPI2_MFGPAGE_DEVID_SAS2308_3 (0x006E)
|
|
|
|
|
|
|
|
|
|
/* Manufacturing Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_0
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 ChipName[16]; /* 0x04 */
|
|
U8 ChipRevision[8]; /* 0x14 */
|
|
U8 BoardName[16]; /* 0x1C */
|
|
U8 BoardAssembly[16]; /* 0x2C */
|
|
U8 BoardTracerNumber[16]; /* 0x3C */
|
|
} MPI2_CONFIG_PAGE_MAN_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_0,
|
|
Mpi2ManufacturingPage0_t, MPI2_POINTER pMpi2ManufacturingPage0_t;
|
|
|
|
#define MPI2_MANUFACTURING0_PAGEVERSION (0x00)
|
|
|
|
|
|
/* Manufacturing Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 VPD[256]; /* 0x04 */
|
|
} MPI2_CONFIG_PAGE_MAN_1,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_1,
|
|
Mpi2ManufacturingPage1_t, MPI2_POINTER pMpi2ManufacturingPage1_t;
|
|
|
|
#define MPI2_MANUFACTURING1_PAGEVERSION (0x00)
|
|
|
|
|
|
typedef struct _MPI2_CHIP_REVISION_ID
|
|
{
|
|
U16 DeviceID; /* 0x00 */
|
|
U8 PCIRevisionID; /* 0x02 */
|
|
U8 Reserved; /* 0x03 */
|
|
} MPI2_CHIP_REVISION_ID, MPI2_POINTER PTR_MPI2_CHIP_REVISION_ID,
|
|
Mpi2ChipRevisionId_t, MPI2_POINTER pMpi2ChipRevisionId_t;
|
|
|
|
|
|
/* Manufacturing Page 2 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check Header.PageLength at runtime.
|
|
*/
|
|
#ifndef MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS
|
|
#define MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_2
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
MPI2_CHIP_REVISION_ID ChipId; /* 0x04 */
|
|
U32 HwSettings[MPI2_MAN_PAGE_2_HW_SETTINGS_WORDS];/* 0x08 */
|
|
} MPI2_CONFIG_PAGE_MAN_2,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_2,
|
|
Mpi2ManufacturingPage2_t, MPI2_POINTER pMpi2ManufacturingPage2_t;
|
|
|
|
#define MPI2_MANUFACTURING2_PAGEVERSION (0x00)
|
|
|
|
|
|
/* Manufacturing Page 3 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check Header.PageLength at runtime.
|
|
*/
|
|
#ifndef MPI2_MAN_PAGE_3_INFO_WORDS
|
|
#define MPI2_MAN_PAGE_3_INFO_WORDS (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_3
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
MPI2_CHIP_REVISION_ID ChipId; /* 0x04 */
|
|
U32 Info[MPI2_MAN_PAGE_3_INFO_WORDS];/* 0x08 */
|
|
} MPI2_CONFIG_PAGE_MAN_3,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_3,
|
|
Mpi2ManufacturingPage3_t, MPI2_POINTER pMpi2ManufacturingPage3_t;
|
|
|
|
#define MPI2_MANUFACTURING3_PAGEVERSION (0x00)
|
|
|
|
|
|
/* Manufacturing Page 4 */
|
|
|
|
typedef struct _MPI2_MANPAGE4_PWR_SAVE_SETTINGS
|
|
{
|
|
U8 PowerSaveFlags; /* 0x00 */
|
|
U8 InternalOperationsSleepTime; /* 0x01 */
|
|
U8 InternalOperationsRunTime; /* 0x02 */
|
|
U8 HostIdleTime; /* 0x03 */
|
|
} MPI2_MANPAGE4_PWR_SAVE_SETTINGS,
|
|
MPI2_POINTER PTR_MPI2_MANPAGE4_PWR_SAVE_SETTINGS,
|
|
Mpi2ManPage4PwrSaveSettings_t, MPI2_POINTER pMpi2ManPage4PwrSaveSettings_t;
|
|
|
|
/* defines for the PowerSaveFlags field */
|
|
#define MPI2_MANPAGE4_MASK_POWERSAVE_MODE (0x03)
|
|
#define MPI2_MANPAGE4_POWERSAVE_MODE_DISABLED (0x00)
|
|
#define MPI2_MANPAGE4_CUSTOM_POWERSAVE_MODE (0x01)
|
|
#define MPI2_MANPAGE4_FULL_POWERSAVE_MODE (0x02)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_4
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x04 */
|
|
U32 Flags; /* 0x08 */
|
|
U8 InquirySize; /* 0x0C */
|
|
U8 Reserved2; /* 0x0D */
|
|
U16 Reserved3; /* 0x0E */
|
|
U8 InquiryData[56]; /* 0x10 */
|
|
U32 RAID0VolumeSettings; /* 0x48 */
|
|
U32 RAID1EVolumeSettings; /* 0x4C */
|
|
U32 RAID1VolumeSettings; /* 0x50 */
|
|
U32 RAID10VolumeSettings; /* 0x54 */
|
|
U32 Reserved4; /* 0x58 */
|
|
U32 Reserved5; /* 0x5C */
|
|
MPI2_MANPAGE4_PWR_SAVE_SETTINGS PowerSaveSettings; /* 0x60 */
|
|
U8 MaxOCEDisks; /* 0x64 */
|
|
U8 ResyncRate; /* 0x65 */
|
|
U16 DataScrubDuration; /* 0x66 */
|
|
U8 MaxHotSpares; /* 0x68 */
|
|
U8 MaxPhysDisksPerVol; /* 0x69 */
|
|
U8 MaxPhysDisks; /* 0x6A */
|
|
U8 MaxVolumes; /* 0x6B */
|
|
} MPI2_CONFIG_PAGE_MAN_4,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_4,
|
|
Mpi2ManufacturingPage4_t, MPI2_POINTER pMpi2ManufacturingPage4_t;
|
|
|
|
#define MPI2_MANUFACTURING4_PAGEVERSION (0x0A)
|
|
|
|
/* Manufacturing Page 4 Flags field */
|
|
#define MPI2_MANPAGE4_METADATA_SIZE_MASK (0x00030000)
|
|
#define MPI2_MANPAGE4_METADATA_512MB (0x00000000)
|
|
|
|
#define MPI2_MANPAGE4_MIX_SSD_SAS_SATA (0x00008000)
|
|
#define MPI2_MANPAGE4_MIX_SSD_AND_NON_SSD (0x00004000)
|
|
#define MPI2_MANPAGE4_HIDE_PHYSDISK_NON_IR (0x00002000)
|
|
|
|
#define MPI2_MANPAGE4_MASK_PHYSDISK_COERCION (0x00001C00)
|
|
#define MPI2_MANPAGE4_PHYSDISK_COERCION_1GB (0x00000000)
|
|
#define MPI2_MANPAGE4_PHYSDISK_128MB_COERCION (0x00000400)
|
|
#define MPI2_MANPAGE4_PHYSDISK_ADAPTIVE_COERCION (0x00000800)
|
|
#define MPI2_MANPAGE4_PHYSDISK_ZERO_COERCION (0x00000C00)
|
|
|
|
#define MPI2_MANPAGE4_MASK_BAD_BLOCK_MARKING (0x00000300)
|
|
#define MPI2_MANPAGE4_DEFAULT_BAD_BLOCK_MARKING (0x00000000)
|
|
#define MPI2_MANPAGE4_TABLE_BAD_BLOCK_MARKING (0x00000100)
|
|
#define MPI2_MANPAGE4_WRITE_LONG_BAD_BLOCK_MARKING (0x00000200)
|
|
|
|
#define MPI2_MANPAGE4_FORCE_OFFLINE_FAILOVER (0x00000080)
|
|
#define MPI2_MANPAGE4_RAID10_DISABLE (0x00000040)
|
|
#define MPI2_MANPAGE4_RAID1E_DISABLE (0x00000020)
|
|
#define MPI2_MANPAGE4_RAID1_DISABLE (0x00000010)
|
|
#define MPI2_MANPAGE4_RAID0_DISABLE (0x00000008)
|
|
#define MPI2_MANPAGE4_IR_MODEPAGE8_DISABLE (0x00000004)
|
|
#define MPI2_MANPAGE4_IM_RESYNC_CACHE_ENABLE (0x00000002)
|
|
#define MPI2_MANPAGE4_IR_NO_MIX_SAS_SATA (0x00000001)
|
|
|
|
|
|
/* Manufacturing Page 5 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_MAN_PAGE_5_PHY_ENTRIES
|
|
#define MPI2_MAN_PAGE_5_PHY_ENTRIES (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_MANUFACTURING5_ENTRY
|
|
{
|
|
U64 WWID; /* 0x00 */
|
|
U64 DeviceName; /* 0x08 */
|
|
} MPI2_MANUFACTURING5_ENTRY, MPI2_POINTER PTR_MPI2_MANUFACTURING5_ENTRY,
|
|
Mpi2Manufacturing5Entry_t, MPI2_POINTER pMpi2Manufacturing5Entry_t;
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_5
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumPhys; /* 0x04 */
|
|
U8 Reserved1; /* 0x05 */
|
|
U16 Reserved2; /* 0x06 */
|
|
U32 Reserved3; /* 0x08 */
|
|
U32 Reserved4; /* 0x0C */
|
|
MPI2_MANUFACTURING5_ENTRY Phy[MPI2_MAN_PAGE_5_PHY_ENTRIES];/* 0x08 */
|
|
} MPI2_CONFIG_PAGE_MAN_5,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_5,
|
|
Mpi2ManufacturingPage5_t, MPI2_POINTER pMpi2ManufacturingPage5_t;
|
|
|
|
#define MPI2_MANUFACTURING5_PAGEVERSION (0x03)
|
|
|
|
|
|
/* Manufacturing Page 6 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_6
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 ProductSpecificInfo;/* 0x04 */
|
|
} MPI2_CONFIG_PAGE_MAN_6,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_6,
|
|
Mpi2ManufacturingPage6_t, MPI2_POINTER pMpi2ManufacturingPage6_t;
|
|
|
|
#define MPI2_MANUFACTURING6_PAGEVERSION (0x00)
|
|
|
|
|
|
/* Manufacturing Page 7 */
|
|
|
|
typedef struct _MPI2_MANPAGE7_CONNECTOR_INFO
|
|
{
|
|
U32 Pinout; /* 0x00 */
|
|
U8 Connector[16]; /* 0x04 */
|
|
U8 Location; /* 0x14 */
|
|
U8 ReceptacleID; /* 0x15 */
|
|
U16 Slot; /* 0x16 */
|
|
U32 Reserved2; /* 0x18 */
|
|
} MPI2_MANPAGE7_CONNECTOR_INFO, MPI2_POINTER PTR_MPI2_MANPAGE7_CONNECTOR_INFO,
|
|
Mpi2ManPage7ConnectorInfo_t, MPI2_POINTER pMpi2ManPage7ConnectorInfo_t;
|
|
|
|
/* defines for the Pinout field */
|
|
#define MPI2_MANPAGE7_PINOUT_LANE_MASK (0x0000FF00)
|
|
#define MPI2_MANPAGE7_PINOUT_LANE_SHIFT (8)
|
|
|
|
#define MPI2_MANPAGE7_PINOUT_TYPE_MASK (0x000000FF)
|
|
#define MPI2_MANPAGE7_PINOUT_TYPE_UNKNOWN (0x00)
|
|
#define MPI2_MANPAGE7_PINOUT_SATA_SINGLE (0x01)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8482 (0x02)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8486 (0x03)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8484 (0x04)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8087 (0x05)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8643_4I (0x06)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8643_8I (0x07)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8470 (0x08)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8088 (0x09)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8644_4X (0x0A)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8644_8X (0x0B)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8644_16X (0x0C)
|
|
#define MPI2_MANPAGE7_PINOUT_SFF_8436 (0x0D)
|
|
|
|
/* defines for the Location field */
|
|
#define MPI2_MANPAGE7_LOCATION_UNKNOWN (0x01)
|
|
#define MPI2_MANPAGE7_LOCATION_INTERNAL (0x02)
|
|
#define MPI2_MANPAGE7_LOCATION_EXTERNAL (0x04)
|
|
#define MPI2_MANPAGE7_LOCATION_SWITCHABLE (0x08)
|
|
#define MPI2_MANPAGE7_LOCATION_AUTO (0x10)
|
|
#define MPI2_MANPAGE7_LOCATION_NOT_PRESENT (0x20)
|
|
#define MPI2_MANPAGE7_LOCATION_NOT_CONNECTED (0x80)
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_MANPAGE7_CONNECTOR_INFO_MAX
|
|
#define MPI2_MANPAGE7_CONNECTOR_INFO_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_7
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x04 */
|
|
U32 Reserved2; /* 0x08 */
|
|
U32 Flags; /* 0x0C */
|
|
U8 EnclosureName[16]; /* 0x10 */
|
|
U8 NumPhys; /* 0x20 */
|
|
U8 Reserved3; /* 0x21 */
|
|
U16 Reserved4; /* 0x22 */
|
|
MPI2_MANPAGE7_CONNECTOR_INFO ConnectorInfo[MPI2_MANPAGE7_CONNECTOR_INFO_MAX]; /* 0x24 */
|
|
} MPI2_CONFIG_PAGE_MAN_7,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_7,
|
|
Mpi2ManufacturingPage7_t, MPI2_POINTER pMpi2ManufacturingPage7_t;
|
|
|
|
#define MPI2_MANUFACTURING7_PAGEVERSION (0x01)
|
|
|
|
/* defines for the Flags field */
|
|
#define MPI2_MANPAGE7_FLAG_USE_SLOT_INFO (0x00000001)
|
|
|
|
|
|
/*
|
|
* Generic structure to use for product-specific manufacturing pages
|
|
* (currently Manufacturing Page 8 through Manufacturing Page 31).
|
|
*/
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_MAN_PS
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 ProductSpecificInfo;/* 0x04 */
|
|
} MPI2_CONFIG_PAGE_MAN_PS,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_MAN_PS,
|
|
Mpi2ManufacturingPagePS_t, MPI2_POINTER pMpi2ManufacturingPagePS_t;
|
|
|
|
#define MPI2_MANUFACTURING8_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING9_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING10_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING11_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING12_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING13_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING14_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING15_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING16_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING17_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING18_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING19_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING20_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING21_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING22_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING23_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING24_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING25_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING26_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING27_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING28_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING29_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING30_PAGEVERSION (0x00)
|
|
#define MPI2_MANUFACTURING31_PAGEVERSION (0x00)
|
|
|
|
|
|
/****************************************************************************
|
|
* IO Unit Config Pages
|
|
****************************************************************************/
|
|
|
|
/* IO Unit Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_0
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U64 UniqueValue; /* 0x04 */
|
|
MPI2_VERSION_UNION NvdataVersionDefault; /* 0x08 */
|
|
MPI2_VERSION_UNION NvdataVersionPersistent; /* 0x0A */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_0,
|
|
Mpi2IOUnitPage0_t, MPI2_POINTER pMpi2IOUnitPage0_t;
|
|
|
|
#define MPI2_IOUNITPAGE0_PAGEVERSION (0x02)
|
|
|
|
|
|
/* IO Unit Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Flags; /* 0x04 */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_1,
|
|
Mpi2IOUnitPage1_t, MPI2_POINTER pMpi2IOUnitPage1_t;
|
|
|
|
#define MPI2_IOUNITPAGE1_PAGEVERSION (0x04)
|
|
|
|
/* IO Unit Page 1 Flags defines */
|
|
#define MPI2_IOUNITPAGE1_ENABLE_HOST_BASED_DISCOVERY (0x00000800)
|
|
#define MPI2_IOUNITPAGE1_MASK_SATA_WRITE_CACHE (0x00000600)
|
|
#define MPI2_IOUNITPAGE1_SATA_WRITE_CACHE_SHIFT (9)
|
|
#define MPI2_IOUNITPAGE1_ENABLE_SATA_WRITE_CACHE (0x00000000)
|
|
#define MPI2_IOUNITPAGE1_DISABLE_SATA_WRITE_CACHE (0x00000200)
|
|
#define MPI2_IOUNITPAGE1_UNCHANGED_SATA_WRITE_CACHE (0x00000400)
|
|
#define MPI2_IOUNITPAGE1_NATIVE_COMMAND_Q_DISABLE (0x00000100)
|
|
#define MPI2_IOUNITPAGE1_DISABLE_IR (0x00000040)
|
|
#define MPI2_IOUNITPAGE1_DISABLE_TASK_SET_FULL_HANDLING (0x00000020)
|
|
#define MPI2_IOUNITPAGE1_IR_USE_STATIC_VOLUME_ID (0x00000004)
|
|
|
|
|
|
/* IO Unit Page 3 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for GPIOCount at runtime.
|
|
*/
|
|
#ifndef MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX
|
|
#define MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_3
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 GPIOCount; /* 0x04 */
|
|
U8 Reserved1; /* 0x05 */
|
|
U16 Reserved2; /* 0x06 */
|
|
U16 GPIOVal[MPI2_IO_UNIT_PAGE_3_GPIO_VAL_MAX];/* 0x08 */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_3, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_3,
|
|
Mpi2IOUnitPage3_t, MPI2_POINTER pMpi2IOUnitPage3_t;
|
|
|
|
#define MPI2_IOUNITPAGE3_PAGEVERSION (0x01)
|
|
|
|
/* defines for IO Unit Page 3 GPIOVal field */
|
|
#define MPI2_IOUNITPAGE3_GPIO_FUNCTION_MASK (0xFFFC)
|
|
#define MPI2_IOUNITPAGE3_GPIO_FUNCTION_SHIFT (2)
|
|
#define MPI2_IOUNITPAGE3_GPIO_SETTING_OFF (0x0000)
|
|
#define MPI2_IOUNITPAGE3_GPIO_SETTING_ON (0x0001)
|
|
|
|
|
|
/* IO Unit Page 5 */
|
|
|
|
/*
|
|
* Upper layer code (drivers, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumDmaEngines at runtime.
|
|
*/
|
|
#ifndef MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES
|
|
#define MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_5
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U64 RaidAcceleratorBufferBaseAddress; /* 0x04 */
|
|
U64 RaidAcceleratorBufferSize; /* 0x0C */
|
|
U64 RaidAcceleratorControlBaseAddress; /* 0x14 */
|
|
U8 RAControlSize; /* 0x1C */
|
|
U8 NumDmaEngines; /* 0x1D */
|
|
U8 RAMinControlSize; /* 0x1E */
|
|
U8 RAMaxControlSize; /* 0x1F */
|
|
U32 Reserved1; /* 0x20 */
|
|
U32 Reserved2; /* 0x24 */
|
|
U32 Reserved3; /* 0x28 */
|
|
U32 DmaEngineCapabilities[MPI2_IOUNITPAGE5_DMAENGINE_ENTRIES]; /* 0x2C */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_5, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_5,
|
|
Mpi2IOUnitPage5_t, MPI2_POINTER pMpi2IOUnitPage5_t;
|
|
|
|
#define MPI2_IOUNITPAGE5_PAGEVERSION (0x00)
|
|
|
|
/* defines for IO Unit Page 5 DmaEngineCapabilities field */
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_MASK_MAX_REQUESTS (0xFF00)
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_SHIFT_MAX_REQUESTS (16)
|
|
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_EEDP (0x0008)
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_PARITY_GENERATION (0x0004)
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_HASHING (0x0002)
|
|
#define MPI2_IOUNITPAGE5_DMA_CAP_ENCRYPTION (0x0001)
|
|
|
|
|
|
/* IO Unit Page 6 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_6
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U16 Flags; /* 0x04 */
|
|
U8 RAHostControlSize; /* 0x06 */
|
|
U8 Reserved0; /* 0x07 */
|
|
U64 RaidAcceleratorHostControlBaseAddress; /* 0x08 */
|
|
U32 Reserved1; /* 0x10 */
|
|
U32 Reserved2; /* 0x14 */
|
|
U32 Reserved3; /* 0x18 */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_6, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_6,
|
|
Mpi2IOUnitPage6_t, MPI2_POINTER pMpi2IOUnitPage6_t;
|
|
|
|
#define MPI2_IOUNITPAGE6_PAGEVERSION (0x00)
|
|
|
|
/* defines for IO Unit Page 6 Flags field */
|
|
#define MPI2_IOUNITPAGE6_FLAGS_ENABLE_RAID_ACCELERATOR (0x0001)
|
|
|
|
|
|
/* IO Unit Page 7 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IO_UNIT_7
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U16 Reserved1; /* 0x04 */
|
|
U8 PCIeWidth; /* 0x06 */
|
|
U8 PCIeSpeed; /* 0x07 */
|
|
U32 ProcessorState; /* 0x08 */
|
|
U32 PowerManagementCapabilities; /* 0x0C */
|
|
U16 IOCTemperature; /* 0x10 */
|
|
U8 IOCTemperatureUnits; /* 0x12 */
|
|
U8 IOCSpeed; /* 0x13 */
|
|
U16 BoardTemperature; /* 0x14 */
|
|
U8 BoardTemperatureUnits; /* 0x16 */
|
|
U8 Reserved3; /* 0x17 */
|
|
} MPI2_CONFIG_PAGE_IO_UNIT_7, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IO_UNIT_7,
|
|
Mpi2IOUnitPage7_t, MPI2_POINTER pMpi2IOUnitPage7_t;
|
|
|
|
#define MPI2_IOUNITPAGE7_PAGEVERSION (0x02)
|
|
|
|
/* defines for IO Unit Page 7 PCIeWidth field */
|
|
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X1 (0x01)
|
|
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X2 (0x02)
|
|
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X4 (0x04)
|
|
#define MPI2_IOUNITPAGE7_PCIE_WIDTH_X8 (0x08)
|
|
|
|
/* defines for IO Unit Page 7 PCIeSpeed field */
|
|
#define MPI2_IOUNITPAGE7_PCIE_SPEED_2_5_GBPS (0x00)
|
|
#define MPI2_IOUNITPAGE7_PCIE_SPEED_5_0_GBPS (0x01)
|
|
#define MPI2_IOUNITPAGE7_PCIE_SPEED_8_0_GBPS (0x02)
|
|
|
|
/* defines for IO Unit Page 7 ProcessorState field */
|
|
#define MPI2_IOUNITPAGE7_PSTATE_MASK_SECOND (0x0000000F)
|
|
#define MPI2_IOUNITPAGE7_PSTATE_SHIFT_SECOND (0)
|
|
|
|
#define MPI2_IOUNITPAGE7_PSTATE_NOT_PRESENT (0x00)
|
|
#define MPI2_IOUNITPAGE7_PSTATE_DISABLED (0x01)
|
|
#define MPI2_IOUNITPAGE7_PSTATE_ENABLED (0x02)
|
|
|
|
/* defines for IO Unit Page 7 PowerManagementCapabilities field */
|
|
#define MPI2_IOUNITPAGE7_PMCAP_12_5_PCT_IOCSPEED (0x00000400)
|
|
#define MPI2_IOUNITPAGE7_PMCAP_25_0_PCT_IOCSPEED (0x00000200)
|
|
#define MPI2_IOUNITPAGE7_PMCAP_50_0_PCT_IOCSPEED (0x00000100)
|
|
#define MPI2_IOUNITPAGE7_PMCAP_PCIE_WIDTH_CHANGE (0x00000008)
|
|
#define MPI2_IOUNITPAGE7_PMCAP_PCIE_SPEED_CHANGE (0x00000004)
|
|
|
|
/* defines for IO Unit Page 7 IOCTemperatureUnits field */
|
|
#define MPI2_IOUNITPAGE7_IOC_TEMP_NOT_PRESENT (0x00)
|
|
#define MPI2_IOUNITPAGE7_IOC_TEMP_FAHRENHEIT (0x01)
|
|
#define MPI2_IOUNITPAGE7_IOC_TEMP_CELSIUS (0x02)
|
|
|
|
/* defines for IO Unit Page 7 IOCSpeed field */
|
|
#define MPI2_IOUNITPAGE7_IOC_SPEED_FULL (0x01)
|
|
#define MPI2_IOUNITPAGE7_IOC_SPEED_HALF (0x02)
|
|
#define MPI2_IOUNITPAGE7_IOC_SPEED_QUARTER (0x04)
|
|
#define MPI2_IOUNITPAGE7_IOC_SPEED_EIGHTH (0x08)
|
|
|
|
/* defines for IO Unit Page 7 BoardTemperatureUnits field */
|
|
#define MPI2_IOUNITPAGE7_BOARD_TEMP_NOT_PRESENT (0x00)
|
|
#define MPI2_IOUNITPAGE7_BOARD_TEMP_FAHRENHEIT (0x01)
|
|
#define MPI2_IOUNITPAGE7_BOARD_TEMP_CELSIUS (0x02)
|
|
|
|
|
|
|
|
/****************************************************************************
|
|
* IOC Config Pages
|
|
****************************************************************************/
|
|
|
|
/* IOC Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IOC_0
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x04 */
|
|
U32 Reserved2; /* 0x08 */
|
|
U16 VendorID; /* 0x0C */
|
|
U16 DeviceID; /* 0x0E */
|
|
U8 RevisionID; /* 0x10 */
|
|
U8 Reserved3; /* 0x11 */
|
|
U16 Reserved4; /* 0x12 */
|
|
U32 ClassCode; /* 0x14 */
|
|
U16 SubsystemVendorID; /* 0x18 */
|
|
U16 SubsystemID; /* 0x1A */
|
|
} MPI2_CONFIG_PAGE_IOC_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IOC_0,
|
|
Mpi2IOCPage0_t, MPI2_POINTER pMpi2IOCPage0_t;
|
|
|
|
#define MPI2_IOCPAGE0_PAGEVERSION (0x02)
|
|
|
|
|
|
/* IOC Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IOC_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Flags; /* 0x04 */
|
|
U32 CoalescingTimeout; /* 0x08 */
|
|
U8 CoalescingDepth; /* 0x0C */
|
|
U8 PCISlotNum; /* 0x0D */
|
|
U8 PCIBusNum; /* 0x0E */
|
|
U8 PCIDomainSegment; /* 0x0F */
|
|
U32 Reserved1; /* 0x10 */
|
|
U32 Reserved2; /* 0x14 */
|
|
} MPI2_CONFIG_PAGE_IOC_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IOC_1,
|
|
Mpi2IOCPage1_t, MPI2_POINTER pMpi2IOCPage1_t;
|
|
|
|
#define MPI2_IOCPAGE1_PAGEVERSION (0x05)
|
|
|
|
/* defines for IOC Page 1 Flags field */
|
|
#define MPI2_IOCPAGE1_REPLY_COALESCING (0x00000001)
|
|
|
|
#define MPI2_IOCPAGE1_PCISLOTNUM_UNKNOWN (0xFF)
|
|
#define MPI2_IOCPAGE1_PCIBUSNUM_UNKNOWN (0xFF)
|
|
#define MPI2_IOCPAGE1_PCIDOMAIN_UNKNOWN (0xFF)
|
|
|
|
/* IOC Page 6 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IOC_6
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 CapabilitiesFlags; /* 0x04 */
|
|
U8 MaxDrivesRAID0; /* 0x08 */
|
|
U8 MaxDrivesRAID1; /* 0x09 */
|
|
U8 MaxDrivesRAID1E; /* 0x0A */
|
|
U8 MaxDrivesRAID10; /* 0x0B */
|
|
U8 MinDrivesRAID0; /* 0x0C */
|
|
U8 MinDrivesRAID1; /* 0x0D */
|
|
U8 MinDrivesRAID1E; /* 0x0E */
|
|
U8 MinDrivesRAID10; /* 0x0F */
|
|
U32 Reserved1; /* 0x10 */
|
|
U8 MaxGlobalHotSpares; /* 0x14 */
|
|
U8 MaxPhysDisks; /* 0x15 */
|
|
U8 MaxVolumes; /* 0x16 */
|
|
U8 MaxConfigs; /* 0x17 */
|
|
U8 MaxOCEDisks; /* 0x18 */
|
|
U8 Reserved2; /* 0x19 */
|
|
U16 Reserved3; /* 0x1A */
|
|
U32 SupportedStripeSizeMapRAID0; /* 0x1C */
|
|
U32 SupportedStripeSizeMapRAID1E; /* 0x20 */
|
|
U32 SupportedStripeSizeMapRAID10; /* 0x24 */
|
|
U32 Reserved4; /* 0x28 */
|
|
U32 Reserved5; /* 0x2C */
|
|
U16 DefaultMetadataSize; /* 0x30 */
|
|
U16 Reserved6; /* 0x32 */
|
|
U16 MaxBadBlockTableEntries; /* 0x34 */
|
|
U16 Reserved7; /* 0x36 */
|
|
U32 IRNvsramVersion; /* 0x38 */
|
|
} MPI2_CONFIG_PAGE_IOC_6, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IOC_6,
|
|
Mpi2IOCPage6_t, MPI2_POINTER pMpi2IOCPage6_t;
|
|
|
|
#define MPI2_IOCPAGE6_PAGEVERSION (0x04)
|
|
|
|
/* defines for IOC Page 6 CapabilitiesFlags */
|
|
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID10_SUPPORT (0x00000010)
|
|
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID1_SUPPORT (0x00000008)
|
|
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID1E_SUPPORT (0x00000004)
|
|
#define MPI2_IOCPAGE6_CAP_FLAGS_RAID0_SUPPORT (0x00000002)
|
|
#define MPI2_IOCPAGE6_CAP_FLAGS_GLOBAL_HOT_SPARE (0x00000001)
|
|
|
|
|
|
/* IOC Page 7 */
|
|
|
|
#define MPI2_IOCPAGE7_EVENTMASK_WORDS (4)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IOC_7
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x04 */
|
|
U32 EventMasks[MPI2_IOCPAGE7_EVENTMASK_WORDS];/* 0x08 */
|
|
U16 SASBroadcastPrimitiveMasks; /* 0x18 */
|
|
U16 Reserved2; /* 0x1A */
|
|
U32 Reserved3; /* 0x1C */
|
|
} MPI2_CONFIG_PAGE_IOC_7, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IOC_7,
|
|
Mpi2IOCPage7_t, MPI2_POINTER pMpi2IOCPage7_t;
|
|
|
|
#define MPI2_IOCPAGE7_PAGEVERSION (0x01)
|
|
|
|
|
|
/* IOC Page 8 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_IOC_8
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumDevsPerEnclosure; /* 0x04 */
|
|
U8 Reserved1; /* 0x05 */
|
|
U16 Reserved2; /* 0x06 */
|
|
U16 MaxPersistentEntries; /* 0x08 */
|
|
U16 MaxNumPhysicalMappedIDs; /* 0x0A */
|
|
U16 Flags; /* 0x0C */
|
|
U16 Reserved3; /* 0x0E */
|
|
U16 IRVolumeMappingFlags; /* 0x10 */
|
|
U16 Reserved4; /* 0x12 */
|
|
U32 Reserved5; /* 0x14 */
|
|
} MPI2_CONFIG_PAGE_IOC_8, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_IOC_8,
|
|
Mpi2IOCPage8_t, MPI2_POINTER pMpi2IOCPage8_t;
|
|
|
|
#define MPI2_IOCPAGE8_PAGEVERSION (0x00)
|
|
|
|
/* defines for IOC Page 8 Flags field */
|
|
#define MPI2_IOCPAGE8_FLAGS_DA_START_SLOT_1 (0x00000020)
|
|
#define MPI2_IOCPAGE8_FLAGS_RESERVED_TARGETID_0 (0x00000010)
|
|
|
|
#define MPI2_IOCPAGE8_FLAGS_MASK_MAPPING_MODE (0x0000000E)
|
|
#define MPI2_IOCPAGE8_FLAGS_DEVICE_PERSISTENCE_MAPPING (0x00000000)
|
|
#define MPI2_IOCPAGE8_FLAGS_ENCLOSURE_SLOT_MAPPING (0x00000002)
|
|
|
|
#define MPI2_IOCPAGE8_FLAGS_DISABLE_PERSISTENT_MAPPING (0x00000001)
|
|
#define MPI2_IOCPAGE8_FLAGS_ENABLE_PERSISTENT_MAPPING (0x00000000)
|
|
|
|
/* defines for IOC Page 8 IRVolumeMappingFlags */
|
|
#define MPI2_IOCPAGE8_IRFLAGS_MASK_VOLUME_MAPPING_MODE (0x00000003)
|
|
#define MPI2_IOCPAGE8_IRFLAGS_LOW_VOLUME_MAPPING (0x00000000)
|
|
#define MPI2_IOCPAGE8_IRFLAGS_HIGH_VOLUME_MAPPING (0x00000001)
|
|
|
|
|
|
/****************************************************************************
|
|
* BIOS Config Pages
|
|
****************************************************************************/
|
|
|
|
/* BIOS Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_BIOS_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 BiosOptions; /* 0x04 */
|
|
U32 IOCSettings; /* 0x08 */
|
|
U32 Reserved1; /* 0x0C */
|
|
U32 DeviceSettings; /* 0x10 */
|
|
U16 NumberOfDevices; /* 0x14 */
|
|
U16 Reserved2; /* 0x16 */
|
|
U16 IOTimeoutBlockDevicesNonRM; /* 0x18 */
|
|
U16 IOTimeoutSequential; /* 0x1A */
|
|
U16 IOTimeoutOther; /* 0x1C */
|
|
U16 IOTimeoutBlockDevicesRM; /* 0x1E */
|
|
} MPI2_CONFIG_PAGE_BIOS_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_BIOS_1,
|
|
Mpi2BiosPage1_t, MPI2_POINTER pMpi2BiosPage1_t;
|
|
|
|
#define MPI2_BIOSPAGE1_PAGEVERSION (0x04)
|
|
|
|
/* values for BIOS Page 1 BiosOptions field */
|
|
#define MPI2_BIOSPAGE1_OPTIONS_DISABLE_BIOS (0x00000001)
|
|
|
|
/* values for BIOS Page 1 IOCSettings field */
|
|
#define MPI2_BIOSPAGE1_IOCSET_MASK_BOOT_PREFERENCE (0x00030000)
|
|
#define MPI2_BIOSPAGE1_IOCSET_ENCLOSURE_SLOT_BOOT (0x00000000)
|
|
#define MPI2_BIOSPAGE1_IOCSET_SAS_ADDRESS_BOOT (0x00010000)
|
|
|
|
#define MPI2_BIOSPAGE1_IOCSET_MASK_RM_SETTING (0x000000C0)
|
|
#define MPI2_BIOSPAGE1_IOCSET_NONE_RM_SETTING (0x00000000)
|
|
#define MPI2_BIOSPAGE1_IOCSET_BOOT_RM_SETTING (0x00000040)
|
|
#define MPI2_BIOSPAGE1_IOCSET_MEDIA_RM_SETTING (0x00000080)
|
|
|
|
#define MPI2_BIOSPAGE1_IOCSET_MASK_ADAPTER_SUPPORT (0x00000030)
|
|
#define MPI2_BIOSPAGE1_IOCSET_NO_SUPPORT (0x00000000)
|
|
#define MPI2_BIOSPAGE1_IOCSET_BIOS_SUPPORT (0x00000010)
|
|
#define MPI2_BIOSPAGE1_IOCSET_OS_SUPPORT (0x00000020)
|
|
#define MPI2_BIOSPAGE1_IOCSET_ALL_SUPPORT (0x00000030)
|
|
|
|
#define MPI2_BIOSPAGE1_IOCSET_ALTERNATE_CHS (0x00000008)
|
|
|
|
/* values for BIOS Page 1 DeviceSettings field */
|
|
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_SMART_POLLING (0x00000010)
|
|
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_SEQ_LUN (0x00000008)
|
|
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_RM_LUN (0x00000004)
|
|
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_NON_RM_LUN (0x00000002)
|
|
#define MPI2_BIOSPAGE1_DEVSET_DISABLE_OTHER_LUN (0x00000001)
|
|
|
|
|
|
/* BIOS Page 2 */
|
|
|
|
typedef struct _MPI2_BOOT_DEVICE_ADAPTER_ORDER
|
|
{
|
|
U32 Reserved1; /* 0x00 */
|
|
U32 Reserved2; /* 0x04 */
|
|
U32 Reserved3; /* 0x08 */
|
|
U32 Reserved4; /* 0x0C */
|
|
U32 Reserved5; /* 0x10 */
|
|
U32 Reserved6; /* 0x14 */
|
|
} MPI2_BOOT_DEVICE_ADAPTER_ORDER,
|
|
MPI2_POINTER PTR_MPI2_BOOT_DEVICE_ADAPTER_ORDER,
|
|
Mpi2BootDeviceAdapterOrder_t, MPI2_POINTER pMpi2BootDeviceAdapterOrder_t;
|
|
|
|
typedef struct _MPI2_BOOT_DEVICE_SAS_WWID
|
|
{
|
|
U64 SASAddress; /* 0x00 */
|
|
U8 LUN[8]; /* 0x08 */
|
|
U32 Reserved1; /* 0x10 */
|
|
U32 Reserved2; /* 0x14 */
|
|
} MPI2_BOOT_DEVICE_SAS_WWID, MPI2_POINTER PTR_MPI2_BOOT_DEVICE_SAS_WWID,
|
|
Mpi2BootDeviceSasWwid_t, MPI2_POINTER pMpi2BootDeviceSasWwid_t;
|
|
|
|
typedef struct _MPI2_BOOT_DEVICE_ENCLOSURE_SLOT
|
|
{
|
|
U64 EnclosureLogicalID; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U32 Reserved2; /* 0x0C */
|
|
U16 SlotNumber; /* 0x10 */
|
|
U16 Reserved3; /* 0x12 */
|
|
U32 Reserved4; /* 0x14 */
|
|
} MPI2_BOOT_DEVICE_ENCLOSURE_SLOT,
|
|
MPI2_POINTER PTR_MPI2_BOOT_DEVICE_ENCLOSURE_SLOT,
|
|
Mpi2BootDeviceEnclosureSlot_t, MPI2_POINTER pMpi2BootDeviceEnclosureSlot_t;
|
|
|
|
typedef struct _MPI2_BOOT_DEVICE_DEVICE_NAME
|
|
{
|
|
U64 DeviceName; /* 0x00 */
|
|
U8 LUN[8]; /* 0x08 */
|
|
U32 Reserved1; /* 0x10 */
|
|
U32 Reserved2; /* 0x14 */
|
|
} MPI2_BOOT_DEVICE_DEVICE_NAME, MPI2_POINTER PTR_MPI2_BOOT_DEVICE_DEVICE_NAME,
|
|
Mpi2BootDeviceDeviceName_t, MPI2_POINTER pMpi2BootDeviceDeviceName_t;
|
|
|
|
typedef union _MPI2_MPI2_BIOSPAGE2_BOOT_DEVICE
|
|
{
|
|
MPI2_BOOT_DEVICE_ADAPTER_ORDER AdapterOrder;
|
|
MPI2_BOOT_DEVICE_SAS_WWID SasWwid;
|
|
MPI2_BOOT_DEVICE_ENCLOSURE_SLOT EnclosureSlot;
|
|
MPI2_BOOT_DEVICE_DEVICE_NAME DeviceName;
|
|
} MPI2_BIOSPAGE2_BOOT_DEVICE, MPI2_POINTER PTR_MPI2_BIOSPAGE2_BOOT_DEVICE,
|
|
Mpi2BiosPage2BootDevice_t, MPI2_POINTER pMpi2BiosPage2BootDevice_t;
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_BIOS_2
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x04 */
|
|
U32 Reserved2; /* 0x08 */
|
|
U32 Reserved3; /* 0x0C */
|
|
U32 Reserved4; /* 0x10 */
|
|
U32 Reserved5; /* 0x14 */
|
|
U32 Reserved6; /* 0x18 */
|
|
U8 ReqBootDeviceForm; /* 0x1C */
|
|
U8 Reserved7; /* 0x1D */
|
|
U16 Reserved8; /* 0x1E */
|
|
MPI2_BIOSPAGE2_BOOT_DEVICE RequestedBootDevice; /* 0x20 */
|
|
U8 ReqAltBootDeviceForm; /* 0x38 */
|
|
U8 Reserved9; /* 0x39 */
|
|
U16 Reserved10; /* 0x3A */
|
|
MPI2_BIOSPAGE2_BOOT_DEVICE RequestedAltBootDevice; /* 0x3C */
|
|
U8 CurrentBootDeviceForm; /* 0x58 */
|
|
U8 Reserved11; /* 0x59 */
|
|
U16 Reserved12; /* 0x5A */
|
|
MPI2_BIOSPAGE2_BOOT_DEVICE CurrentBootDevice; /* 0x58 */
|
|
} MPI2_CONFIG_PAGE_BIOS_2, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_BIOS_2,
|
|
Mpi2BiosPage2_t, MPI2_POINTER pMpi2BiosPage2_t;
|
|
|
|
#define MPI2_BIOSPAGE2_PAGEVERSION (0x04)
|
|
|
|
/* values for BIOS Page 2 BootDeviceForm fields */
|
|
#define MPI2_BIOSPAGE2_FORM_MASK (0x0F)
|
|
#define MPI2_BIOSPAGE2_FORM_NO_DEVICE_SPECIFIED (0x00)
|
|
#define MPI2_BIOSPAGE2_FORM_SAS_WWID (0x05)
|
|
#define MPI2_BIOSPAGE2_FORM_ENCLOSURE_SLOT (0x06)
|
|
#define MPI2_BIOSPAGE2_FORM_DEVICE_NAME (0x07)
|
|
|
|
|
|
/* BIOS Page 3 */
|
|
|
|
typedef struct _MPI2_ADAPTER_INFO
|
|
{
|
|
U8 PciBusNumber; /* 0x00 */
|
|
U8 PciDeviceAndFunctionNumber; /* 0x01 */
|
|
U16 AdapterFlags; /* 0x02 */
|
|
} MPI2_ADAPTER_INFO, MPI2_POINTER PTR_MPI2_ADAPTER_INFO,
|
|
Mpi2AdapterInfo_t, MPI2_POINTER pMpi2AdapterInfo_t;
|
|
|
|
#define MPI2_ADAPTER_INFO_FLAGS_EMBEDDED (0x0001)
|
|
#define MPI2_ADAPTER_INFO_FLAGS_INIT_STATUS (0x0002)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_BIOS_3
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U32 GlobalFlags; /* 0x04 */
|
|
U32 BiosVersion; /* 0x08 */
|
|
MPI2_ADAPTER_INFO AdapterOrder[4]; /* 0x0C */
|
|
U32 Reserved1; /* 0x1C */
|
|
} MPI2_CONFIG_PAGE_BIOS_3, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_BIOS_3,
|
|
Mpi2BiosPage3_t, MPI2_POINTER pMpi2BiosPage3_t;
|
|
|
|
#define MPI2_BIOSPAGE3_PAGEVERSION (0x00)
|
|
|
|
/* values for BIOS Page 3 GlobalFlags */
|
|
#define MPI2_BIOSPAGE3_FLAGS_PAUSE_ON_ERROR (0x00000002)
|
|
#define MPI2_BIOSPAGE3_FLAGS_VERBOSE_ENABLE (0x00000004)
|
|
#define MPI2_BIOSPAGE3_FLAGS_HOOK_INT_40_DISABLE (0x00000010)
|
|
|
|
#define MPI2_BIOSPAGE3_FLAGS_DEV_LIST_DISPLAY_MASK (0x000000E0)
|
|
#define MPI2_BIOSPAGE3_FLAGS_INSTALLED_DEV_DISPLAY (0x00000000)
|
|
#define MPI2_BIOSPAGE3_FLAGS_ADAPTER_DISPLAY (0x00000020)
|
|
#define MPI2_BIOSPAGE3_FLAGS_ADAPTER_DEV_DISPLAY (0x00000040)
|
|
|
|
|
|
/* BIOS Page 4 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_BIOS_PAGE_4_PHY_ENTRIES
|
|
#define MPI2_BIOS_PAGE_4_PHY_ENTRIES (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_BIOS4_ENTRY
|
|
{
|
|
U64 ReassignmentWWID; /* 0x00 */
|
|
U64 ReassignmentDeviceName; /* 0x08 */
|
|
} MPI2_BIOS4_ENTRY, MPI2_POINTER PTR_MPI2_BIOS4_ENTRY,
|
|
Mpi2MBios4Entry_t, MPI2_POINTER pMpi2Bios4Entry_t;
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_BIOS_4
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumPhys; /* 0x04 */
|
|
U8 Reserved1; /* 0x05 */
|
|
U16 Reserved2; /* 0x06 */
|
|
MPI2_BIOS4_ENTRY Phy[MPI2_BIOS_PAGE_4_PHY_ENTRIES]; /* 0x08 */
|
|
} MPI2_CONFIG_PAGE_BIOS_4, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_BIOS_4,
|
|
Mpi2BiosPage4_t, MPI2_POINTER pMpi2BiosPage4_t;
|
|
|
|
#define MPI2_BIOSPAGE4_PAGEVERSION (0x01)
|
|
|
|
|
|
/****************************************************************************
|
|
* RAID Volume Config Pages
|
|
****************************************************************************/
|
|
|
|
/* RAID Volume Page 0 */
|
|
|
|
typedef struct _MPI2_RAIDVOL0_PHYS_DISK
|
|
{
|
|
U8 RAIDSetNum; /* 0x00 */
|
|
U8 PhysDiskMap; /* 0x01 */
|
|
U8 PhysDiskNum; /* 0x02 */
|
|
U8 Reserved; /* 0x03 */
|
|
} MPI2_RAIDVOL0_PHYS_DISK, MPI2_POINTER PTR_MPI2_RAIDVOL0_PHYS_DISK,
|
|
Mpi2RaidVol0PhysDisk_t, MPI2_POINTER pMpi2RaidVol0PhysDisk_t;
|
|
|
|
/* defines for the PhysDiskMap field */
|
|
#define MPI2_RAIDVOL0_PHYSDISK_PRIMARY (0x01)
|
|
#define MPI2_RAIDVOL0_PHYSDISK_SECONDARY (0x02)
|
|
|
|
typedef struct _MPI2_RAIDVOL0_SETTINGS
|
|
{
|
|
U16 Settings; /* 0x00 */
|
|
U8 HotSparePool; /* 0x01 */
|
|
U8 Reserved; /* 0x02 */
|
|
} MPI2_RAIDVOL0_SETTINGS, MPI2_POINTER PTR_MPI2_RAIDVOL0_SETTINGS,
|
|
Mpi2RaidVol0Settings_t, MPI2_POINTER pMpi2RaidVol0Settings_t;
|
|
|
|
/* RAID Volume Page 0 HotSparePool defines, also used in RAID Physical Disk */
|
|
#define MPI2_RAID_HOT_SPARE_POOL_0 (0x01)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_1 (0x02)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_2 (0x04)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_3 (0x08)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_4 (0x10)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_5 (0x20)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_6 (0x40)
|
|
#define MPI2_RAID_HOT_SPARE_POOL_7 (0x80)
|
|
|
|
/* RAID Volume Page 0 VolumeSettings defines */
|
|
#define MPI2_RAIDVOL0_SETTING_USE_PRODUCT_ID_SUFFIX (0x0008)
|
|
#define MPI2_RAIDVOL0_SETTING_AUTO_CONFIG_HSWAP_DISABLE (0x0004)
|
|
|
|
#define MPI2_RAIDVOL0_SETTING_MASK_WRITE_CACHING (0x0003)
|
|
#define MPI2_RAIDVOL0_SETTING_UNCHANGED (0x0000)
|
|
#define MPI2_RAIDVOL0_SETTING_DISABLE_WRITE_CACHING (0x0001)
|
|
#define MPI2_RAIDVOL0_SETTING_ENABLE_WRITE_CACHING (0x0002)
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhysDisks at runtime.
|
|
*/
|
|
#ifndef MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX
|
|
#define MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_RAID_VOL_0
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U16 DevHandle; /* 0x04 */
|
|
U8 VolumeState; /* 0x06 */
|
|
U8 VolumeType; /* 0x07 */
|
|
U32 VolumeStatusFlags; /* 0x08 */
|
|
MPI2_RAIDVOL0_SETTINGS VolumeSettings; /* 0x0C */
|
|
U64 MaxLBA; /* 0x10 */
|
|
U32 StripeSize; /* 0x18 */
|
|
U16 BlockSize; /* 0x1C */
|
|
U16 Reserved1; /* 0x1E */
|
|
U8 SupportedPhysDisks; /* 0x20 */
|
|
U8 ResyncRate; /* 0x21 */
|
|
U16 DataScrubDuration; /* 0x22 */
|
|
U8 NumPhysDisks; /* 0x24 */
|
|
U8 Reserved2; /* 0x25 */
|
|
U8 Reserved3; /* 0x26 */
|
|
U8 InactiveStatus; /* 0x27 */
|
|
MPI2_RAIDVOL0_PHYS_DISK PhysDisk[MPI2_RAID_VOL_PAGE_0_PHYSDISK_MAX]; /* 0x28 */
|
|
} MPI2_CONFIG_PAGE_RAID_VOL_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_RAID_VOL_0,
|
|
Mpi2RaidVolPage0_t, MPI2_POINTER pMpi2RaidVolPage0_t;
|
|
|
|
#define MPI2_RAIDVOLPAGE0_PAGEVERSION (0x0A)
|
|
|
|
/* values for RAID VolumeState */
|
|
#define MPI2_RAID_VOL_STATE_MISSING (0x00)
|
|
#define MPI2_RAID_VOL_STATE_FAILED (0x01)
|
|
#define MPI2_RAID_VOL_STATE_INITIALIZING (0x02)
|
|
#define MPI2_RAID_VOL_STATE_ONLINE (0x03)
|
|
#define MPI2_RAID_VOL_STATE_DEGRADED (0x04)
|
|
#define MPI2_RAID_VOL_STATE_OPTIMAL (0x05)
|
|
|
|
/* values for RAID VolumeType */
|
|
#define MPI2_RAID_VOL_TYPE_RAID0 (0x00)
|
|
#define MPI2_RAID_VOL_TYPE_RAID1E (0x01)
|
|
#define MPI2_RAID_VOL_TYPE_RAID1 (0x02)
|
|
#define MPI2_RAID_VOL_TYPE_RAID10 (0x05)
|
|
#define MPI2_RAID_VOL_TYPE_UNKNOWN (0xFF)
|
|
|
|
/* values for RAID Volume Page 0 VolumeStatusFlags field */
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_PENDING_RESYNC (0x02000000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_BACKG_INIT_PENDING (0x01000000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_MDC_PENDING (0x00800000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_USER_CONSIST_PENDING (0x00400000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_MAKE_DATA_CONSISTENT (0x00200000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_DATA_SCRUB (0x00100000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_CONSISTENCY_CHECK (0x00080000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_CAPACITY_EXPANSION (0x00040000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_BACKGROUND_INIT (0x00020000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_RESYNC_IN_PROGRESS (0x00010000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_VOL_NOT_CONSISTENT (0x00000080)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_OCE_ALLOWED (0x00000040)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_BGI_COMPLETE (0x00000020)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_1E_OFFSET_MIRROR (0x00000000)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_1E_ADJACENT_MIRROR (0x00000010)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_BAD_BLOCK_TABLE_FULL (0x00000008)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_VOLUME_INACTIVE (0x00000004)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_QUIESCED (0x00000002)
|
|
#define MPI2_RAIDVOL0_STATUS_FLAG_ENABLED (0x00000001)
|
|
|
|
/* values for RAID Volume Page 0 SupportedPhysDisks field */
|
|
#define MPI2_RAIDVOL0_SUPPORT_SOLID_STATE_DISKS (0x08)
|
|
#define MPI2_RAIDVOL0_SUPPORT_HARD_DISKS (0x04)
|
|
#define MPI2_RAIDVOL0_SUPPORT_SAS_PROTOCOL (0x02)
|
|
#define MPI2_RAIDVOL0_SUPPORT_SATA_PROTOCOL (0x01)
|
|
|
|
/* values for RAID Volume Page 0 InactiveStatus field */
|
|
#define MPI2_RAIDVOLPAGE0_UNKNOWN_INACTIVE (0x00)
|
|
#define MPI2_RAIDVOLPAGE0_STALE_METADATA_INACTIVE (0x01)
|
|
#define MPI2_RAIDVOLPAGE0_FOREIGN_VOLUME_INACTIVE (0x02)
|
|
#define MPI2_RAIDVOLPAGE0_INSUFFICIENT_RESOURCE_INACTIVE (0x03)
|
|
#define MPI2_RAIDVOLPAGE0_CLONE_VOLUME_INACTIVE (0x04)
|
|
#define MPI2_RAIDVOLPAGE0_INSUFFICIENT_METADATA_INACTIVE (0x05)
|
|
#define MPI2_RAIDVOLPAGE0_PREVIOUSLY_DELETED (0x06)
|
|
|
|
|
|
/* RAID Volume Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_RAID_VOL_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U16 DevHandle; /* 0x04 */
|
|
U16 Reserved0; /* 0x06 */
|
|
U8 GUID[24]; /* 0x08 */
|
|
U8 Name[16]; /* 0x20 */
|
|
U64 WWID; /* 0x30 */
|
|
U32 Reserved1; /* 0x38 */
|
|
U32 Reserved2; /* 0x3C */
|
|
} MPI2_CONFIG_PAGE_RAID_VOL_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_RAID_VOL_1,
|
|
Mpi2RaidVolPage1_t, MPI2_POINTER pMpi2RaidVolPage1_t;
|
|
|
|
#define MPI2_RAIDVOLPAGE1_PAGEVERSION (0x03)
|
|
|
|
|
|
/****************************************************************************
|
|
* RAID Physical Disk Config Pages
|
|
****************************************************************************/
|
|
|
|
/* RAID Physical Disk Page 0 */
|
|
|
|
typedef struct _MPI2_RAIDPHYSDISK0_SETTINGS
|
|
{
|
|
U16 Reserved1; /* 0x00 */
|
|
U8 HotSparePool; /* 0x02 */
|
|
U8 Reserved2; /* 0x03 */
|
|
} MPI2_RAIDPHYSDISK0_SETTINGS, MPI2_POINTER PTR_MPI2_RAIDPHYSDISK0_SETTINGS,
|
|
Mpi2RaidPhysDisk0Settings_t, MPI2_POINTER pMpi2RaidPhysDisk0Settings_t;
|
|
|
|
/* use MPI2_RAID_HOT_SPARE_POOL_ defines for the HotSparePool field */
|
|
|
|
typedef struct _MPI2_RAIDPHYSDISK0_INQUIRY_DATA
|
|
{
|
|
U8 VendorID[8]; /* 0x00 */
|
|
U8 ProductID[16]; /* 0x08 */
|
|
U8 ProductRevLevel[4]; /* 0x18 */
|
|
U8 SerialNum[32]; /* 0x1C */
|
|
} MPI2_RAIDPHYSDISK0_INQUIRY_DATA,
|
|
MPI2_POINTER PTR_MPI2_RAIDPHYSDISK0_INQUIRY_DATA,
|
|
Mpi2RaidPhysDisk0InquiryData_t, MPI2_POINTER pMpi2RaidPhysDisk0InquiryData_t;
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_RD_PDISK_0
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U16 DevHandle; /* 0x04 */
|
|
U8 Reserved1; /* 0x06 */
|
|
U8 PhysDiskNum; /* 0x07 */
|
|
MPI2_RAIDPHYSDISK0_SETTINGS PhysDiskSettings; /* 0x08 */
|
|
U32 Reserved2; /* 0x0C */
|
|
MPI2_RAIDPHYSDISK0_INQUIRY_DATA InquiryData; /* 0x10 */
|
|
U32 Reserved3; /* 0x4C */
|
|
U8 PhysDiskState; /* 0x50 */
|
|
U8 OfflineReason; /* 0x51 */
|
|
U8 IncompatibleReason; /* 0x52 */
|
|
U8 PhysDiskAttributes; /* 0x53 */
|
|
U32 PhysDiskStatusFlags; /* 0x54 */
|
|
U64 DeviceMaxLBA; /* 0x58 */
|
|
U64 HostMaxLBA; /* 0x60 */
|
|
U64 CoercedMaxLBA; /* 0x68 */
|
|
U16 BlockSize; /* 0x70 */
|
|
U16 Reserved5; /* 0x72 */
|
|
U32 Reserved6; /* 0x74 */
|
|
} MPI2_CONFIG_PAGE_RD_PDISK_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_RD_PDISK_0,
|
|
Mpi2RaidPhysDiskPage0_t, MPI2_POINTER pMpi2RaidPhysDiskPage0_t;
|
|
|
|
#define MPI2_RAIDPHYSDISKPAGE0_PAGEVERSION (0x05)
|
|
|
|
/* PhysDiskState defines */
|
|
#define MPI2_RAID_PD_STATE_NOT_CONFIGURED (0x00)
|
|
#define MPI2_RAID_PD_STATE_NOT_COMPATIBLE (0x01)
|
|
#define MPI2_RAID_PD_STATE_OFFLINE (0x02)
|
|
#define MPI2_RAID_PD_STATE_ONLINE (0x03)
|
|
#define MPI2_RAID_PD_STATE_HOT_SPARE (0x04)
|
|
#define MPI2_RAID_PD_STATE_DEGRADED (0x05)
|
|
#define MPI2_RAID_PD_STATE_REBUILDING (0x06)
|
|
#define MPI2_RAID_PD_STATE_OPTIMAL (0x07)
|
|
|
|
/* OfflineReason defines */
|
|
#define MPI2_PHYSDISK0_ONLINE (0x00)
|
|
#define MPI2_PHYSDISK0_OFFLINE_MISSING (0x01)
|
|
#define MPI2_PHYSDISK0_OFFLINE_FAILED (0x03)
|
|
#define MPI2_PHYSDISK0_OFFLINE_INITIALIZING (0x04)
|
|
#define MPI2_PHYSDISK0_OFFLINE_REQUESTED (0x05)
|
|
#define MPI2_PHYSDISK0_OFFLINE_FAILED_REQUESTED (0x06)
|
|
#define MPI2_PHYSDISK0_OFFLINE_OTHER (0xFF)
|
|
|
|
/* IncompatibleReason defines */
|
|
#define MPI2_PHYSDISK0_COMPATIBLE (0x00)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_PROTOCOL (0x01)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_BLOCKSIZE (0x02)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_MAX_LBA (0x03)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_SATA_EXTENDED_CMD (0x04)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_REMOVEABLE_MEDIA (0x05)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_MEDIA_TYPE (0x06)
|
|
#define MPI2_PHYSDISK0_INCOMPATIBLE_UNKNOWN (0xFF)
|
|
|
|
/* PhysDiskAttributes defines */
|
|
#define MPI2_PHYSDISK0_ATTRIB_MEDIA_MASK (0x0C)
|
|
#define MPI2_PHYSDISK0_ATTRIB_SOLID_STATE_DRIVE (0x08)
|
|
#define MPI2_PHYSDISK0_ATTRIB_HARD_DISK_DRIVE (0x04)
|
|
|
|
#define MPI2_PHYSDISK0_ATTRIB_PROTOCOL_MASK (0x03)
|
|
#define MPI2_PHYSDISK0_ATTRIB_SAS_PROTOCOL (0x02)
|
|
#define MPI2_PHYSDISK0_ATTRIB_SATA_PROTOCOL (0x01)
|
|
|
|
/* PhysDiskStatusFlags defines */
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_NOT_CERTIFIED (0x00000040)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_OCE_TARGET (0x00000020)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_WRITE_CACHE_ENABLED (0x00000010)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_OPTIMAL_PREVIOUS (0x00000000)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_NOT_OPTIMAL_PREVIOUS (0x00000008)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_INACTIVE_VOLUME (0x00000004)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_QUIESCED (0x00000002)
|
|
#define MPI2_PHYSDISK0_STATUS_FLAG_OUT_OF_SYNC (0x00000001)
|
|
|
|
|
|
/* RAID Physical Disk Page 1 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhysDiskPaths at runtime.
|
|
*/
|
|
#ifndef MPI2_RAID_PHYS_DISK1_PATH_MAX
|
|
#define MPI2_RAID_PHYS_DISK1_PATH_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_RAIDPHYSDISK1_PATH
|
|
{
|
|
U16 DevHandle; /* 0x00 */
|
|
U16 Reserved1; /* 0x02 */
|
|
U64 WWID; /* 0x04 */
|
|
U64 OwnerWWID; /* 0x0C */
|
|
U8 OwnerIdentifier; /* 0x14 */
|
|
U8 Reserved2; /* 0x15 */
|
|
U16 Flags; /* 0x16 */
|
|
} MPI2_RAIDPHYSDISK1_PATH, MPI2_POINTER PTR_MPI2_RAIDPHYSDISK1_PATH,
|
|
Mpi2RaidPhysDisk1Path_t, MPI2_POINTER pMpi2RaidPhysDisk1Path_t;
|
|
|
|
/* RAID Physical Disk Page 1 Physical Disk Path Flags field defines */
|
|
#define MPI2_RAID_PHYSDISK1_FLAG_PRIMARY (0x0004)
|
|
#define MPI2_RAID_PHYSDISK1_FLAG_BROKEN (0x0002)
|
|
#define MPI2_RAID_PHYSDISK1_FLAG_INVALID (0x0001)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_RD_PDISK_1
|
|
{
|
|
MPI2_CONFIG_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumPhysDiskPaths; /* 0x04 */
|
|
U8 PhysDiskNum; /* 0x05 */
|
|
U16 Reserved1; /* 0x06 */
|
|
U32 Reserved2; /* 0x08 */
|
|
MPI2_RAIDPHYSDISK1_PATH PhysicalDiskPath[MPI2_RAID_PHYS_DISK1_PATH_MAX];/* 0x0C */
|
|
} MPI2_CONFIG_PAGE_RD_PDISK_1,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_RD_PDISK_1,
|
|
Mpi2RaidPhysDiskPage1_t, MPI2_POINTER pMpi2RaidPhysDiskPage1_t;
|
|
|
|
#define MPI2_RAIDPHYSDISKPAGE1_PAGEVERSION (0x02)
|
|
|
|
|
|
/****************************************************************************
|
|
* values for fields used by several types of SAS Config Pages
|
|
****************************************************************************/
|
|
|
|
/* values for NegotiatedLinkRates fields */
|
|
#define MPI2_SAS_NEG_LINK_RATE_MASK_LOGICAL (0xF0)
|
|
#define MPI2_SAS_NEG_LINK_RATE_SHIFT_LOGICAL (4)
|
|
#define MPI2_SAS_NEG_LINK_RATE_MASK_PHYSICAL (0x0F)
|
|
/* link rates used for Negotiated Physical and Logical Link Rate */
|
|
#define MPI2_SAS_NEG_LINK_RATE_UNKNOWN_LINK_RATE (0x00)
|
|
#define MPI2_SAS_NEG_LINK_RATE_PHY_DISABLED (0x01)
|
|
#define MPI2_SAS_NEG_LINK_RATE_NEGOTIATION_FAILED (0x02)
|
|
#define MPI2_SAS_NEG_LINK_RATE_SATA_OOB_COMPLETE (0x03)
|
|
#define MPI2_SAS_NEG_LINK_RATE_PORT_SELECTOR (0x04)
|
|
#define MPI2_SAS_NEG_LINK_RATE_SMP_RESET_IN_PROGRESS (0x05)
|
|
#define MPI2_SAS_NEG_LINK_RATE_UNSUPPORTED_PHY (0x06)
|
|
#define MPI2_SAS_NEG_LINK_RATE_1_5 (0x08)
|
|
#define MPI2_SAS_NEG_LINK_RATE_3_0 (0x09)
|
|
#define MPI2_SAS_NEG_LINK_RATE_6_0 (0x0A)
|
|
|
|
|
|
/* values for AttachedPhyInfo fields */
|
|
#define MPI2_SAS_APHYINFO_INSIDE_ZPSDS_PERSISTENT (0x00000040)
|
|
#define MPI2_SAS_APHYINFO_REQUESTED_INSIDE_ZPSDS (0x00000020)
|
|
#define MPI2_SAS_APHYINFO_BREAK_REPLY_CAPABLE (0x00000010)
|
|
|
|
#define MPI2_SAS_APHYINFO_REASON_MASK (0x0000000F)
|
|
#define MPI2_SAS_APHYINFO_REASON_UNKNOWN (0x00000000)
|
|
#define MPI2_SAS_APHYINFO_REASON_POWER_ON (0x00000001)
|
|
#define MPI2_SAS_APHYINFO_REASON_HARD_RESET (0x00000002)
|
|
#define MPI2_SAS_APHYINFO_REASON_SMP_PHY_CONTROL (0x00000003)
|
|
#define MPI2_SAS_APHYINFO_REASON_LOSS_OF_SYNC (0x00000004)
|
|
#define MPI2_SAS_APHYINFO_REASON_MULTIPLEXING_SEQ (0x00000005)
|
|
#define MPI2_SAS_APHYINFO_REASON_IT_NEXUS_LOSS_TIMER (0x00000006)
|
|
#define MPI2_SAS_APHYINFO_REASON_BREAK_TIMEOUT (0x00000007)
|
|
#define MPI2_SAS_APHYINFO_REASON_PHY_TEST_STOPPED (0x00000008)
|
|
|
|
|
|
/* values for PhyInfo fields */
|
|
#define MPI2_SAS_PHYINFO_PHY_VACANT (0x80000000)
|
|
|
|
#define MPI2_SAS_PHYINFO_PHY_POWER_CONDITION_MASK (0x18000000)
|
|
#define MPI2_SAS_PHYINFO_SHIFT_PHY_POWER_CONDITION (27)
|
|
#define MPI2_SAS_PHYINFO_PHY_POWER_ACTIVE (0x00000000)
|
|
#define MPI2_SAS_PHYINFO_PHY_POWER_PARTIAL (0x08000000)
|
|
#define MPI2_SAS_PHYINFO_PHY_POWER_SLUMBER (0x10000000)
|
|
|
|
#define MPI2_SAS_PHYINFO_CHANGED_REQ_INSIDE_ZPSDS (0x04000000)
|
|
#define MPI2_SAS_PHYINFO_INSIDE_ZPSDS_PERSISTENT (0x02000000)
|
|
#define MPI2_SAS_PHYINFO_REQ_INSIDE_ZPSDS (0x01000000)
|
|
#define MPI2_SAS_PHYINFO_ZONE_GROUP_PERSISTENT (0x00400000)
|
|
#define MPI2_SAS_PHYINFO_INSIDE_ZPSDS (0x00200000)
|
|
#define MPI2_SAS_PHYINFO_ZONING_ENABLED (0x00100000)
|
|
|
|
#define MPI2_SAS_PHYINFO_REASON_MASK (0x000F0000)
|
|
#define MPI2_SAS_PHYINFO_REASON_UNKNOWN (0x00000000)
|
|
#define MPI2_SAS_PHYINFO_REASON_POWER_ON (0x00010000)
|
|
#define MPI2_SAS_PHYINFO_REASON_HARD_RESET (0x00020000)
|
|
#define MPI2_SAS_PHYINFO_REASON_SMP_PHY_CONTROL (0x00030000)
|
|
#define MPI2_SAS_PHYINFO_REASON_LOSS_OF_SYNC (0x00040000)
|
|
#define MPI2_SAS_PHYINFO_REASON_MULTIPLEXING_SEQ (0x00050000)
|
|
#define MPI2_SAS_PHYINFO_REASON_IT_NEXUS_LOSS_TIMER (0x00060000)
|
|
#define MPI2_SAS_PHYINFO_REASON_BREAK_TIMEOUT (0x00070000)
|
|
#define MPI2_SAS_PHYINFO_REASON_PHY_TEST_STOPPED (0x00080000)
|
|
|
|
#define MPI2_SAS_PHYINFO_MULTIPLEXING_SUPPORTED (0x00008000)
|
|
#define MPI2_SAS_PHYINFO_SATA_PORT_ACTIVE (0x00004000)
|
|
#define MPI2_SAS_PHYINFO_SATA_PORT_SELECTOR_PRESENT (0x00002000)
|
|
#define MPI2_SAS_PHYINFO_VIRTUAL_PHY (0x00001000)
|
|
|
|
#define MPI2_SAS_PHYINFO_MASK_PARTIAL_PATHWAY_TIME (0x00000F00)
|
|
#define MPI2_SAS_PHYINFO_SHIFT_PARTIAL_PATHWAY_TIME (8)
|
|
|
|
#define MPI2_SAS_PHYINFO_MASK_ROUTING_ATTRIBUTE (0x000000F0)
|
|
#define MPI2_SAS_PHYINFO_DIRECT_ROUTING (0x00000000)
|
|
#define MPI2_SAS_PHYINFO_SUBTRACTIVE_ROUTING (0x00000010)
|
|
#define MPI2_SAS_PHYINFO_TABLE_ROUTING (0x00000020)
|
|
|
|
|
|
/* values for SAS ProgrammedLinkRate fields */
|
|
#define MPI2_SAS_PRATE_MAX_RATE_MASK (0xF0)
|
|
#define MPI2_SAS_PRATE_MAX_RATE_NOT_PROGRAMMABLE (0x00)
|
|
#define MPI2_SAS_PRATE_MAX_RATE_1_5 (0x80)
|
|
#define MPI2_SAS_PRATE_MAX_RATE_3_0 (0x90)
|
|
#define MPI2_SAS_PRATE_MAX_RATE_6_0 (0xA0)
|
|
#define MPI2_SAS_PRATE_MIN_RATE_MASK (0x0F)
|
|
#define MPI2_SAS_PRATE_MIN_RATE_NOT_PROGRAMMABLE (0x00)
|
|
#define MPI2_SAS_PRATE_MIN_RATE_1_5 (0x08)
|
|
#define MPI2_SAS_PRATE_MIN_RATE_3_0 (0x09)
|
|
#define MPI2_SAS_PRATE_MIN_RATE_6_0 (0x0A)
|
|
|
|
|
|
/* values for SAS HwLinkRate fields */
|
|
#define MPI2_SAS_HWRATE_MAX_RATE_MASK (0xF0)
|
|
#define MPI2_SAS_HWRATE_MAX_RATE_1_5 (0x80)
|
|
#define MPI2_SAS_HWRATE_MAX_RATE_3_0 (0x90)
|
|
#define MPI2_SAS_HWRATE_MAX_RATE_6_0 (0xA0)
|
|
#define MPI2_SAS_HWRATE_MIN_RATE_MASK (0x0F)
|
|
#define MPI2_SAS_HWRATE_MIN_RATE_1_5 (0x08)
|
|
#define MPI2_SAS_HWRATE_MIN_RATE_3_0 (0x09)
|
|
#define MPI2_SAS_HWRATE_MIN_RATE_6_0 (0x0A)
|
|
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS IO Unit Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS IO Unit Page 0 */
|
|
|
|
typedef struct _MPI2_SAS_IO_UNIT0_PHY_DATA
|
|
{
|
|
U8 Port; /* 0x00 */
|
|
U8 PortFlags; /* 0x01 */
|
|
U8 PhyFlags; /* 0x02 */
|
|
U8 NegotiatedLinkRate; /* 0x03 */
|
|
U32 ControllerPhyDeviceInfo;/* 0x04 */
|
|
U16 AttachedDevHandle; /* 0x08 */
|
|
U16 ControllerDevHandle; /* 0x0A */
|
|
U32 DiscoveryStatus; /* 0x0C */
|
|
U32 Reserved; /* 0x10 */
|
|
} MPI2_SAS_IO_UNIT0_PHY_DATA, MPI2_POINTER PTR_MPI2_SAS_IO_UNIT0_PHY_DATA,
|
|
Mpi2SasIOUnit0PhyData_t, MPI2_POINTER pMpi2SasIOUnit0PhyData_t;
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT0_PHY_MAX
|
|
#define MPI2_SAS_IOUNIT0_PHY_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U8 NumPhys; /* 0x0C */
|
|
U8 Reserved2; /* 0x0D */
|
|
U16 Reserved3; /* 0x0E */
|
|
MPI2_SAS_IO_UNIT0_PHY_DATA PhyData[MPI2_SAS_IOUNIT0_PHY_MAX]; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_0,
|
|
Mpi2SasIOUnitPage0_t, MPI2_POINTER pMpi2SasIOUnitPage0_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE0_PAGEVERSION (0x05)
|
|
|
|
/* values for SAS IO Unit Page 0 PortFlags */
|
|
#define MPI2_SASIOUNIT0_PORTFLAGS_DISCOVERY_IN_PROGRESS (0x08)
|
|
#define MPI2_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG (0x01)
|
|
|
|
/* values for SAS IO Unit Page 0 PhyFlags */
|
|
#define MPI2_SASIOUNIT0_PHYFLAGS_ZONING_ENABLED (0x10)
|
|
#define MPI2_SASIOUNIT0_PHYFLAGS_PHY_DISABLED (0x08)
|
|
|
|
/* use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
|
|
|
|
/* see mpi2_sas.h for values for SAS IO Unit Page 0 ControllerPhyDeviceInfo values */
|
|
|
|
/* values for SAS IO Unit Page 0 DiscoveryStatus */
|
|
#define MPI2_SASIOUNIT0_DS_MAX_ENCLOSURES_EXCEED (0x80000000)
|
|
#define MPI2_SASIOUNIT0_DS_MAX_EXPANDERS_EXCEED (0x40000000)
|
|
#define MPI2_SASIOUNIT0_DS_MAX_DEVICES_EXCEED (0x20000000)
|
|
#define MPI2_SASIOUNIT0_DS_MAX_TOPO_PHYS_EXCEED (0x10000000)
|
|
#define MPI2_SASIOUNIT0_DS_DOWNSTREAM_INITIATOR (0x08000000)
|
|
#define MPI2_SASIOUNIT0_DS_MULTI_SUBTRACTIVE_SUBTRACTIVE (0x00008000)
|
|
#define MPI2_SASIOUNIT0_DS_EXP_MULTI_SUBTRACTIVE (0x00004000)
|
|
#define MPI2_SASIOUNIT0_DS_MULTI_PORT_DOMAIN (0x00002000)
|
|
#define MPI2_SASIOUNIT0_DS_TABLE_TO_SUBTRACTIVE_LINK (0x00001000)
|
|
#define MPI2_SASIOUNIT0_DS_UNSUPPORTED_DEVICE (0x00000800)
|
|
#define MPI2_SASIOUNIT0_DS_TABLE_LINK (0x00000400)
|
|
#define MPI2_SASIOUNIT0_DS_SUBTRACTIVE_LINK (0x00000200)
|
|
#define MPI2_SASIOUNIT0_DS_SMP_CRC_ERROR (0x00000100)
|
|
#define MPI2_SASIOUNIT0_DS_SMP_FUNCTION_FAILED (0x00000080)
|
|
#define MPI2_SASIOUNIT0_DS_INDEX_NOT_EXIST (0x00000040)
|
|
#define MPI2_SASIOUNIT0_DS_OUT_ROUTE_ENTRIES (0x00000020)
|
|
#define MPI2_SASIOUNIT0_DS_SMP_TIMEOUT (0x00000010)
|
|
#define MPI2_SASIOUNIT0_DS_MULTIPLE_PORTS (0x00000004)
|
|
#define MPI2_SASIOUNIT0_DS_UNADDRESSABLE_DEVICE (0x00000002)
|
|
#define MPI2_SASIOUNIT0_DS_LOOP_DETECTED (0x00000001)
|
|
|
|
|
|
/* SAS IO Unit Page 1 */
|
|
|
|
typedef struct _MPI2_SAS_IO_UNIT1_PHY_DATA
|
|
{
|
|
U8 Port; /* 0x00 */
|
|
U8 PortFlags; /* 0x01 */
|
|
U8 PhyFlags; /* 0x02 */
|
|
U8 MaxMinLinkRate; /* 0x03 */
|
|
U32 ControllerPhyDeviceInfo; /* 0x04 */
|
|
U16 MaxTargetPortConnectTime; /* 0x08 */
|
|
U16 Reserved1; /* 0x0A */
|
|
} MPI2_SAS_IO_UNIT1_PHY_DATA, MPI2_POINTER PTR_MPI2_SAS_IO_UNIT1_PHY_DATA,
|
|
Mpi2SasIOUnit1PhyData_t, MPI2_POINTER pMpi2SasIOUnit1PhyData_t;
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT1_PHY_MAX
|
|
#define MPI2_SAS_IOUNIT1_PHY_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_1
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U16 ControlFlags; /* 0x08 */
|
|
U16 SASNarrowMaxQueueDepth; /* 0x0A */
|
|
U16 AdditionalControlFlags; /* 0x0C */
|
|
U16 SASWideMaxQueueDepth; /* 0x0E */
|
|
U8 NumPhys; /* 0x10 */
|
|
U8 SATAMaxQDepth; /* 0x11 */
|
|
U8 ReportDeviceMissingDelay; /* 0x12 */
|
|
U8 IODeviceMissingDelay; /* 0x13 */
|
|
MPI2_SAS_IO_UNIT1_PHY_DATA PhyData[MPI2_SAS_IOUNIT1_PHY_MAX]; /* 0x14 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_1,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_1,
|
|
Mpi2SasIOUnitPage1_t, MPI2_POINTER pMpi2SasIOUnitPage1_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE1_PAGEVERSION (0x09)
|
|
|
|
/* values for SAS IO Unit Page 1 ControlFlags */
|
|
#define MPI2_SASIOUNIT1_CONTROL_DEVICE_SELF_TEST (0x8000)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_3_0_MAX (0x4000)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_1_5_MAX (0x2000)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_SW_PRESERVE (0x1000)
|
|
|
|
#define MPI2_SASIOUNIT1_CONTROL_MASK_DEV_SUPPORT (0x0600)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SHIFT_DEV_SUPPORT (9)
|
|
#define MPI2_SASIOUNIT1_CONTROL_DEV_SUPPORT_BOTH (0x0)
|
|
#define MPI2_SASIOUNIT1_CONTROL_DEV_SAS_SUPPORT (0x1)
|
|
#define MPI2_SASIOUNIT1_CONTROL_DEV_SATA_SUPPORT (0x2)
|
|
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_48BIT_LBA_REQUIRED (0x0080)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_SMART_REQUIRED (0x0040)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_NCQ_REQUIRED (0x0020)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SATA_FUA_REQUIRED (0x0010)
|
|
#define MPI2_SASIOUNIT1_CONTROL_TABLE_SUBTRACTIVE_ILLEGAL (0x0008)
|
|
#define MPI2_SASIOUNIT1_CONTROL_SUBTRACTIVE_ILLEGAL (0x0004)
|
|
#define MPI2_SASIOUNIT1_CONTROL_FIRST_LVL_DISC_ONLY (0x0002)
|
|
#define MPI2_SASIOUNIT1_CONTROL_CLEAR_AFFILIATION (0x0001)
|
|
|
|
/* values for SAS IO Unit Page 1 AdditionalControlFlags */
|
|
#define MPI2_SASIOUNIT1_ACONTROL_MULTI_PORT_DOMAIN_ILLEGAL (0x0080)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_SATA_ASYNCHROUNOUS_NOTIFICATION (0x0040)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_INVALID_TOPOLOGY_CORRECTION (0x0020)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_PORT_ENABLE_ONLY_SATA_LINK_RESET (0x0010)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_OTHER_AFFILIATION_SATA_LINK_RESET (0x0008)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_SELF_AFFILIATION_SATA_LINK_RESET (0x0004)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_NO_AFFILIATION_SATA_LINK_RESET (0x0002)
|
|
#define MPI2_SASIOUNIT1_ACONTROL_ALLOW_TABLE_TO_TABLE (0x0001)
|
|
|
|
/* defines for SAS IO Unit Page 1 ReportDeviceMissingDelay */
|
|
#define MPI2_SASIOUNIT1_REPORT_MISSING_TIMEOUT_MASK (0x7F)
|
|
#define MPI2_SASIOUNIT1_REPORT_MISSING_UNIT_16 (0x80)
|
|
|
|
/* values for SAS IO Unit Page 1 PortFlags */
|
|
#define MPI2_SASIOUNIT1_PORT_FLAGS_AUTO_PORT_CONFIG (0x01)
|
|
|
|
/* values for SAS IO Unit Page 1 PhyFlags */
|
|
#define MPI2_SASIOUNIT1_PHYFLAGS_ZONING_ENABLE (0x10)
|
|
#define MPI2_SASIOUNIT1_PHYFLAGS_PHY_DISABLE (0x08)
|
|
|
|
/* values for SAS IO Unit Page 1 MaxMinLinkRate */
|
|
#define MPI2_SASIOUNIT1_MAX_RATE_MASK (0xF0)
|
|
#define MPI2_SASIOUNIT1_MAX_RATE_1_5 (0x80)
|
|
#define MPI2_SASIOUNIT1_MAX_RATE_3_0 (0x90)
|
|
#define MPI2_SASIOUNIT1_MAX_RATE_6_0 (0xA0)
|
|
#define MPI2_SASIOUNIT1_MIN_RATE_MASK (0x0F)
|
|
#define MPI2_SASIOUNIT1_MIN_RATE_1_5 (0x08)
|
|
#define MPI2_SASIOUNIT1_MIN_RATE_3_0 (0x09)
|
|
#define MPI2_SASIOUNIT1_MIN_RATE_6_0 (0x0A)
|
|
|
|
/* see mpi2_sas.h for values for SAS IO Unit Page 1 ControllerPhyDeviceInfo values */
|
|
|
|
|
|
/* SAS IO Unit Page 4 */
|
|
|
|
typedef struct _MPI2_SAS_IOUNIT4_SPINUP_GROUP
|
|
{
|
|
U8 MaxTargetSpinup; /* 0x00 */
|
|
U8 SpinupDelay; /* 0x01 */
|
|
U16 Reserved1; /* 0x02 */
|
|
} MPI2_SAS_IOUNIT4_SPINUP_GROUP, MPI2_POINTER PTR_MPI2_SAS_IOUNIT4_SPINUP_GROUP,
|
|
Mpi2SasIOUnit4SpinupGroup_t, MPI2_POINTER pMpi2SasIOUnit4SpinupGroup_t;
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT4_PHY_MAX
|
|
#define MPI2_SAS_IOUNIT4_PHY_MAX (4)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_4
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
MPI2_SAS_IOUNIT4_SPINUP_GROUP SpinupGroupParameters[4]; /* 0x08 */
|
|
U32 Reserved1; /* 0x18 */
|
|
U32 Reserved2; /* 0x1C */
|
|
U32 Reserved3; /* 0x20 */
|
|
U8 BootDeviceWaitTime; /* 0x24 */
|
|
U8 Reserved4; /* 0x25 */
|
|
U16 Reserved5; /* 0x26 */
|
|
U8 NumPhys; /* 0x28 */
|
|
U8 PEInitialSpinupDelay; /* 0x29 */
|
|
U8 PEReplyDelay; /* 0x2A */
|
|
U8 Flags; /* 0x2B */
|
|
U8 PHY[MPI2_SAS_IOUNIT4_PHY_MAX]; /* 0x2C */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_4,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_4,
|
|
Mpi2SasIOUnitPage4_t, MPI2_POINTER pMpi2SasIOUnitPage4_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE4_PAGEVERSION (0x02)
|
|
|
|
/* defines for Flags field */
|
|
#define MPI2_SASIOUNIT4_FLAGS_AUTO_PORTENABLE (0x01)
|
|
|
|
/* defines for PHY field */
|
|
#define MPI2_SASIOUNIT4_PHY_SPINUP_GROUP_MASK (0x03)
|
|
|
|
|
|
/* SAS IO Unit Page 5 */
|
|
|
|
typedef struct _MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS
|
|
{
|
|
U8 ControlFlags; /* 0x00 */
|
|
U8 PortWidthModGroup; /* 0x01 */
|
|
U16 InactivityTimerExponent; /* 0x02 */
|
|
U8 SATAPartialTimeout; /* 0x04 */
|
|
U8 Reserved2; /* 0x05 */
|
|
U8 SATASlumberTimeout; /* 0x06 */
|
|
U8 Reserved3; /* 0x07 */
|
|
U8 SASPartialTimeout; /* 0x08 */
|
|
U8 Reserved4; /* 0x09 */
|
|
U8 SASSlumberTimeout; /* 0x0A */
|
|
U8 Reserved5; /* 0x0B */
|
|
} MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS,
|
|
MPI2_POINTER PTR_MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS,
|
|
Mpi2SasIOUnit5PhyPmSettings_t, MPI2_POINTER pMpi2SasIOUnit5PhyPmSettings_t;
|
|
|
|
/* defines for ControlFlags field */
|
|
#define MPI2_SASIOUNIT5_CONTROL_SAS_SLUMBER_ENABLE (0x08)
|
|
#define MPI2_SASIOUNIT5_CONTROL_SAS_PARTIAL_ENABLE (0x04)
|
|
#define MPI2_SASIOUNIT5_CONTROL_SATA_SLUMBER_ENABLE (0x02)
|
|
#define MPI2_SASIOUNIT5_CONTROL_SATA_PARTIAL_ENABLE (0x01)
|
|
|
|
/* defines for PortWidthModeGroup field */
|
|
#define MPI2_SASIOUNIT5_PWMG_DISABLE (0xFF)
|
|
|
|
/* defines for InactivityTimerExponent field */
|
|
#define MPI2_SASIOUNIT5_ITE_MASK_SAS_SLUMBER (0x7000)
|
|
#define MPI2_SASIOUNIT5_ITE_SHIFT_SAS_SLUMBER (12)
|
|
#define MPI2_SASIOUNIT5_ITE_MASK_SAS_PARTIAL (0x0700)
|
|
#define MPI2_SASIOUNIT5_ITE_SHIFT_SAS_PARTIAL (8)
|
|
#define MPI2_SASIOUNIT5_ITE_MASK_SATA_SLUMBER (0x0070)
|
|
#define MPI2_SASIOUNIT5_ITE_SHIFT_SATA_SLUMBER (4)
|
|
#define MPI2_SASIOUNIT5_ITE_MASK_SATA_PARTIAL (0x0007)
|
|
#define MPI2_SASIOUNIT5_ITE_SHIFT_SATA_PARTIAL (0)
|
|
|
|
#define MPI2_SASIOUNIT5_ITE_TEN_SECONDS (7)
|
|
#define MPI2_SASIOUNIT5_ITE_ONE_SECOND (6)
|
|
#define MPI2_SASIOUNIT5_ITE_HUNDRED_MILLISECONDS (5)
|
|
#define MPI2_SASIOUNIT5_ITE_TEN_MILLISECONDS (4)
|
|
#define MPI2_SASIOUNIT5_ITE_ONE_MILLISECOND (3)
|
|
#define MPI2_SASIOUNIT5_ITE_HUNDRED_MICROSECONDS (2)
|
|
#define MPI2_SASIOUNIT5_ITE_TEN_MICROSECONDS (1)
|
|
#define MPI2_SASIOUNIT5_ITE_ONE_MICROSECOND (0)
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhys at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT5_PHY_MAX
|
|
#define MPI2_SAS_IOUNIT5_PHY_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_5
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumPhys; /* 0x08 */
|
|
U8 Reserved1; /* 0x09 */
|
|
U16 Reserved2; /* 0x0A */
|
|
U32 Reserved3; /* 0x0C */
|
|
MPI2_SAS_IO_UNIT5_PHY_PM_SETTINGS SASPhyPowerManagementSettings[MPI2_SAS_IOUNIT5_PHY_MAX]; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_5,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_5,
|
|
Mpi2SasIOUnitPage5_t, MPI2_POINTER pMpi2SasIOUnitPage5_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE5_PAGEVERSION (0x01)
|
|
|
|
|
|
/* SAS IO Unit Page 6 */
|
|
|
|
typedef struct _MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS
|
|
{
|
|
U8 CurrentStatus; /* 0x00 */
|
|
U8 CurrentModulation; /* 0x01 */
|
|
U8 CurrentUtilization; /* 0x02 */
|
|
U8 Reserved1; /* 0x03 */
|
|
U32 Reserved2; /* 0x04 */
|
|
} MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS,
|
|
MPI2_POINTER PTR_MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS,
|
|
Mpi2SasIOUnit6PortWidthModGroupStatus_t,
|
|
MPI2_POINTER pMpi2SasIOUnit6PortWidthModGroupStatus_t;
|
|
|
|
/* defines for CurrentStatus field */
|
|
#define MPI2_SASIOUNIT6_STATUS_UNAVAILABLE (0x00)
|
|
#define MPI2_SASIOUNIT6_STATUS_UNCONFIGURED (0x01)
|
|
#define MPI2_SASIOUNIT6_STATUS_INVALID_CONFIG (0x02)
|
|
#define MPI2_SASIOUNIT6_STATUS_LINK_DOWN (0x03)
|
|
#define MPI2_SASIOUNIT6_STATUS_OBSERVATION_ONLY (0x04)
|
|
#define MPI2_SASIOUNIT6_STATUS_INACTIVE (0x05)
|
|
#define MPI2_SASIOUNIT6_STATUS_ACTIVE_IOUNIT (0x06)
|
|
#define MPI2_SASIOUNIT6_STATUS_ACTIVE_HOST (0x07)
|
|
|
|
/* defines for CurrentModulation field */
|
|
#define MPI2_SASIOUNIT6_MODULATION_25_PERCENT (0x00)
|
|
#define MPI2_SASIOUNIT6_MODULATION_50_PERCENT (0x01)
|
|
#define MPI2_SASIOUNIT6_MODULATION_75_PERCENT (0x02)
|
|
#define MPI2_SASIOUNIT6_MODULATION_100_PERCENT (0x03)
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumGroups at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT6_GROUP_MAX
|
|
#define MPI2_SAS_IOUNIT6_GROUP_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_6
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U32 Reserved2; /* 0x0C */
|
|
U8 NumGroups; /* 0x10 */
|
|
U8 Reserved3; /* 0x11 */
|
|
U16 Reserved4; /* 0x12 */
|
|
MPI2_SAS_IO_UNIT6_PORT_WIDTH_MOD_GROUP_STATUS
|
|
PortWidthModulationGroupStatus[MPI2_SAS_IOUNIT6_GROUP_MAX]; /* 0x14 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_6,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_6,
|
|
Mpi2SasIOUnitPage6_t, MPI2_POINTER pMpi2SasIOUnitPage6_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE6_PAGEVERSION (0x00)
|
|
|
|
|
|
/* SAS IO Unit Page 7 */
|
|
|
|
typedef struct _MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS
|
|
{
|
|
U8 Flags; /* 0x00 */
|
|
U8 Reserved1; /* 0x01 */
|
|
U16 Reserved2; /* 0x02 */
|
|
U8 Threshold75Pct; /* 0x04 */
|
|
U8 Threshold50Pct; /* 0x05 */
|
|
U8 Threshold25Pct; /* 0x06 */
|
|
U8 Reserved3; /* 0x07 */
|
|
} MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS,
|
|
MPI2_POINTER PTR_MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS,
|
|
Mpi2SasIOUnit7PortWidthModGroupSettings_t,
|
|
MPI2_POINTER pMpi2SasIOUnit7PortWidthModGroupSettings_t;
|
|
|
|
/* defines for Flags field */
|
|
#define MPI2_SASIOUNIT7_FLAGS_ENABLE_PORT_WIDTH_MODULATION (0x01)
|
|
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumGroups at runtime.
|
|
*/
|
|
#ifndef MPI2_SAS_IOUNIT7_GROUP_MAX
|
|
#define MPI2_SAS_IOUNIT7_GROUP_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_7
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 SamplingInterval; /* 0x08 */
|
|
U8 WindowLength; /* 0x09 */
|
|
U16 Reserved1; /* 0x0A */
|
|
U32 Reserved2; /* 0x0C */
|
|
U32 Reserved3; /* 0x10 */
|
|
U8 NumGroups; /* 0x14 */
|
|
U8 Reserved4; /* 0x15 */
|
|
U16 Reserved5; /* 0x16 */
|
|
MPI2_SAS_IO_UNIT7_PORT_WIDTH_MOD_GROUP_SETTINGS
|
|
PortWidthModulationGroupSettings[MPI2_SAS_IOUNIT7_GROUP_MAX]; /* 0x18 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_7,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_7,
|
|
Mpi2SasIOUnitPage7_t, MPI2_POINTER pMpi2SasIOUnitPage7_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE7_PAGEVERSION (0x00)
|
|
|
|
|
|
/* SAS IO Unit Page 8 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SASIOUNIT_8
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U32 PowerManagementCapabilities; /* 0x0C */
|
|
U32 Reserved2; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_SASIOUNIT_8,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SASIOUNIT_8,
|
|
Mpi2SasIOUnitPage8_t, MPI2_POINTER pMpi2SasIOUnitPage8_t;
|
|
|
|
#define MPI2_SASIOUNITPAGE8_PAGEVERSION (0x00)
|
|
|
|
/* defines for PowerManagementCapabilities field */
|
|
#define MPI2_SASIOUNIT8_PM_HOST_PORT_WIDTH_MOD (0x000001000)
|
|
#define MPI2_SASIOUNIT8_PM_HOST_SAS_SLUMBER_MODE (0x000000800)
|
|
#define MPI2_SASIOUNIT8_PM_HOST_SAS_PARTIAL_MODE (0x000000400)
|
|
#define MPI2_SASIOUNIT8_PM_HOST_SATA_SLUMBER_MODE (0x000000200)
|
|
#define MPI2_SASIOUNIT8_PM_HOST_SATA_PARTIAL_MODE (0x000000100)
|
|
#define MPI2_SASIOUNIT8_PM_IOUNIT_PORT_WIDTH_MOD (0x000000010)
|
|
#define MPI2_SASIOUNIT8_PM_IOUNIT_SAS_SLUMBER_MODE (0x000000008)
|
|
#define MPI2_SASIOUNIT8_PM_IOUNIT_SAS_PARTIAL_MODE (0x000000004)
|
|
#define MPI2_SASIOUNIT8_PM_IOUNIT_SATA_SLUMBER_MODE (0x000000002)
|
|
#define MPI2_SASIOUNIT8_PM_IOUNIT_SATA_PARTIAL_MODE (0x000000001)
|
|
|
|
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS Expander Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS Expander Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_EXPANDER_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 PhysicalPort; /* 0x08 */
|
|
U8 ReportGenLength; /* 0x09 */
|
|
U16 EnclosureHandle; /* 0x0A */
|
|
U64 SASAddress; /* 0x0C */
|
|
U32 DiscoveryStatus; /* 0x14 */
|
|
U16 DevHandle; /* 0x18 */
|
|
U16 ParentDevHandle; /* 0x1A */
|
|
U16 ExpanderChangeCount; /* 0x1C */
|
|
U16 ExpanderRouteIndexes; /* 0x1E */
|
|
U8 NumPhys; /* 0x20 */
|
|
U8 SASLevel; /* 0x21 */
|
|
U16 Flags; /* 0x22 */
|
|
U16 STPBusInactivityTimeLimit; /* 0x24 */
|
|
U16 STPMaxConnectTimeLimit; /* 0x26 */
|
|
U16 STP_SMP_NexusLossTime; /* 0x28 */
|
|
U16 MaxNumRoutedSasAddresses; /* 0x2A */
|
|
U64 ActiveZoneManagerSASAddress;/* 0x2C */
|
|
U16 ZoneLockInactivityLimit; /* 0x34 */
|
|
U16 Reserved1; /* 0x36 */
|
|
U8 TimeToReducedFunc; /* 0x38 */
|
|
U8 InitialTimeToReducedFunc; /* 0x39 */
|
|
U8 MaxReducedFuncTime; /* 0x3A */
|
|
U8 Reserved2; /* 0x3B */
|
|
} MPI2_CONFIG_PAGE_EXPANDER_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_EXPANDER_0,
|
|
Mpi2ExpanderPage0_t, MPI2_POINTER pMpi2ExpanderPage0_t;
|
|
|
|
#define MPI2_SASEXPANDER0_PAGEVERSION (0x06)
|
|
|
|
/* values for SAS Expander Page 0 DiscoveryStatus field */
|
|
#define MPI2_SAS_EXPANDER0_DS_MAX_ENCLOSURES_EXCEED (0x80000000)
|
|
#define MPI2_SAS_EXPANDER0_DS_MAX_EXPANDERS_EXCEED (0x40000000)
|
|
#define MPI2_SAS_EXPANDER0_DS_MAX_DEVICES_EXCEED (0x20000000)
|
|
#define MPI2_SAS_EXPANDER0_DS_MAX_TOPO_PHYS_EXCEED (0x10000000)
|
|
#define MPI2_SAS_EXPANDER0_DS_DOWNSTREAM_INITIATOR (0x08000000)
|
|
#define MPI2_SAS_EXPANDER0_DS_MULTI_SUBTRACTIVE_SUBTRACTIVE (0x00008000)
|
|
#define MPI2_SAS_EXPANDER0_DS_EXP_MULTI_SUBTRACTIVE (0x00004000)
|
|
#define MPI2_SAS_EXPANDER0_DS_MULTI_PORT_DOMAIN (0x00002000)
|
|
#define MPI2_SAS_EXPANDER0_DS_TABLE_TO_SUBTRACTIVE_LINK (0x00001000)
|
|
#define MPI2_SAS_EXPANDER0_DS_UNSUPPORTED_DEVICE (0x00000800)
|
|
#define MPI2_SAS_EXPANDER0_DS_TABLE_LINK (0x00000400)
|
|
#define MPI2_SAS_EXPANDER0_DS_SUBTRACTIVE_LINK (0x00000200)
|
|
#define MPI2_SAS_EXPANDER0_DS_SMP_CRC_ERROR (0x00000100)
|
|
#define MPI2_SAS_EXPANDER0_DS_SMP_FUNCTION_FAILED (0x00000080)
|
|
#define MPI2_SAS_EXPANDER0_DS_INDEX_NOT_EXIST (0x00000040)
|
|
#define MPI2_SAS_EXPANDER0_DS_OUT_ROUTE_ENTRIES (0x00000020)
|
|
#define MPI2_SAS_EXPANDER0_DS_SMP_TIMEOUT (0x00000010)
|
|
#define MPI2_SAS_EXPANDER0_DS_MULTIPLE_PORTS (0x00000004)
|
|
#define MPI2_SAS_EXPANDER0_DS_UNADDRESSABLE_DEVICE (0x00000002)
|
|
#define MPI2_SAS_EXPANDER0_DS_LOOP_DETECTED (0x00000001)
|
|
|
|
/* values for SAS Expander Page 0 Flags field */
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_REDUCED_FUNCTIONALITY (0x2000)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_ZONE_LOCKED (0x1000)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_SUPPORTED_PHYSICAL_PRES (0x0800)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_ASSERTED_PHYSICAL_PRES (0x0400)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_ZONING_SUPPORT (0x0200)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_ENABLED_ZONING (0x0100)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_TABLE_TO_TABLE_SUPPORT (0x0080)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_CONNECTOR_END_DEVICE (0x0010)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_OTHERS_CONFIG (0x0004)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_CONFIG_IN_PROGRESS (0x0002)
|
|
#define MPI2_SAS_EXPANDER0_FLAGS_ROUTE_TABLE_CONFIG (0x0001)
|
|
|
|
|
|
/* SAS Expander Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_EXPANDER_1
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 PhysicalPort; /* 0x08 */
|
|
U8 Reserved1; /* 0x09 */
|
|
U16 Reserved2; /* 0x0A */
|
|
U8 NumPhys; /* 0x0C */
|
|
U8 Phy; /* 0x0D */
|
|
U16 NumTableEntriesProgrammed; /* 0x0E */
|
|
U8 ProgrammedLinkRate; /* 0x10 */
|
|
U8 HwLinkRate; /* 0x11 */
|
|
U16 AttachedDevHandle; /* 0x12 */
|
|
U32 PhyInfo; /* 0x14 */
|
|
U32 AttachedDeviceInfo; /* 0x18 */
|
|
U16 ExpanderDevHandle; /* 0x1C */
|
|
U8 ChangeCount; /* 0x1E */
|
|
U8 NegotiatedLinkRate; /* 0x1F */
|
|
U8 PhyIdentifier; /* 0x20 */
|
|
U8 AttachedPhyIdentifier; /* 0x21 */
|
|
U8 Reserved3; /* 0x22 */
|
|
U8 DiscoveryInfo; /* 0x23 */
|
|
U32 AttachedPhyInfo; /* 0x24 */
|
|
U8 ZoneGroup; /* 0x28 */
|
|
U8 SelfConfigStatus; /* 0x29 */
|
|
U16 Reserved4; /* 0x2A */
|
|
} MPI2_CONFIG_PAGE_EXPANDER_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_EXPANDER_1,
|
|
Mpi2ExpanderPage1_t, MPI2_POINTER pMpi2ExpanderPage1_t;
|
|
|
|
#define MPI2_SASEXPANDER1_PAGEVERSION (0x02)
|
|
|
|
/* use MPI2_SAS_PRATE_ defines for the ProgrammedLinkRate field */
|
|
|
|
/* use MPI2_SAS_HWRATE_ defines for the HwLinkRate field */
|
|
|
|
/* use MPI2_SAS_PHYINFO_ for the PhyInfo field */
|
|
|
|
/* see mpi2_sas.h for the MPI2_SAS_DEVICE_INFO_ defines used for the AttachedDeviceInfo field */
|
|
|
|
/* use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
|
|
|
|
/* use MPI2_SAS_APHYINFO_ defines for AttachedPhyInfo field */
|
|
|
|
/* values for SAS Expander Page 1 DiscoveryInfo field */
|
|
#define MPI2_SAS_EXPANDER1_DISCINFO_BAD_PHY_DISABLED (0x04)
|
|
#define MPI2_SAS_EXPANDER1_DISCINFO_LINK_STATUS_CHANGE (0x02)
|
|
#define MPI2_SAS_EXPANDER1_DISCINFO_NO_ROUTING_ENTRIES (0x01)
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS Device Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS Device Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U16 Slot; /* 0x08 */
|
|
U16 EnclosureHandle; /* 0x0A */
|
|
U64 SASAddress; /* 0x0C */
|
|
U16 ParentDevHandle; /* 0x14 */
|
|
U8 PhyNum; /* 0x16 */
|
|
U8 AccessStatus; /* 0x17 */
|
|
U16 DevHandle; /* 0x18 */
|
|
U8 AttachedPhyIdentifier; /* 0x1A */
|
|
U8 ZoneGroup; /* 0x1B */
|
|
U32 DeviceInfo; /* 0x1C */
|
|
U16 Flags; /* 0x20 */
|
|
U8 PhysicalPort; /* 0x22 */
|
|
U8 MaxPortConnections; /* 0x23 */
|
|
U64 DeviceName; /* 0x24 */
|
|
U8 PortGroups; /* 0x2C */
|
|
U8 DmaGroup; /* 0x2D */
|
|
U8 ControlGroup; /* 0x2E */
|
|
U8 Reserved1; /* 0x2F */
|
|
U32 Reserved2; /* 0x30 */
|
|
U32 Reserved3; /* 0x34 */
|
|
} MPI2_CONFIG_PAGE_SAS_DEV_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_DEV_0,
|
|
Mpi2SasDevicePage0_t, MPI2_POINTER pMpi2SasDevicePage0_t;
|
|
|
|
#define MPI2_SASDEVICE0_PAGEVERSION (0x08)
|
|
|
|
/* values for SAS Device Page 0 AccessStatus field */
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_NO_ERRORS (0x00)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_INIT_FAILED (0x01)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_CAPABILITY_FAILED (0x02)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_AFFILIATION_CONFLICT (0x03)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SATA_NEEDS_INITIALIZATION (0x04)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_ROUTE_NOT_ADDRESSABLE (0x05)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SMP_ERROR_NOT_ADDRESSABLE (0x06)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_DEVICE_BLOCKED (0x07)
|
|
/* specific values for SATA Init failures */
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_UNKNOWN (0x10)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_AFFILIATION_CONFLICT (0x11)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_DIAG (0x12)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_IDENTIFICATION (0x13)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_CHECK_POWER (0x14)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_PIO_SN (0x15)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_MDMA_SN (0x16)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_UDMA_SN (0x17)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_ZONING_VIOLATION (0x18)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_NOT_ADDRESSABLE (0x19)
|
|
#define MPI2_SAS_DEVICE0_ASTATUS_SIF_MAX (0x1F)
|
|
|
|
/* see mpi2_sas.h for values for SAS Device Page 0 DeviceInfo values */
|
|
|
|
/* values for SAS Device Page 0 Flags field */
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SLUMBER_PM_CAPABLE (0x1000)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_PARTIAL_PM_CAPABLE (0x0800)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_ASYNCHRONOUS_NOTIFY (0x0400)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_SW_PRESERVE (0x0200)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_UNSUPPORTED_DEVICE (0x0100)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_48BIT_LBA_SUPPORTED (0x0080)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_SMART_SUPPORTED (0x0040)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_NCQ_SUPPORTED (0x0020)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_SATA_FUA_SUPPORTED (0x0010)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_PORT_SELECTOR_ATTACH (0x0008)
|
|
#define MPI2_SAS_DEVICE0_FLAGS_DEVICE_PRESENT (0x0001)
|
|
|
|
|
|
/* SAS Device Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_DEV_1
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U64 SASAddress; /* 0x0C */
|
|
U32 Reserved2; /* 0x14 */
|
|
U16 DevHandle; /* 0x18 */
|
|
U16 Reserved3; /* 0x1A */
|
|
U8 InitialRegDeviceFIS[20];/* 0x1C */
|
|
} MPI2_CONFIG_PAGE_SAS_DEV_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_DEV_1,
|
|
Mpi2SasDevicePage1_t, MPI2_POINTER pMpi2SasDevicePage1_t;
|
|
|
|
#define MPI2_SASDEVICE1_PAGEVERSION (0x01)
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS PHY Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS PHY Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U16 OwnerDevHandle; /* 0x08 */
|
|
U16 Reserved1; /* 0x0A */
|
|
U16 AttachedDevHandle; /* 0x0C */
|
|
U8 AttachedPhyIdentifier; /* 0x0E */
|
|
U8 Reserved2; /* 0x0F */
|
|
U32 AttachedPhyInfo; /* 0x10 */
|
|
U8 ProgrammedLinkRate; /* 0x14 */
|
|
U8 HwLinkRate; /* 0x15 */
|
|
U8 ChangeCount; /* 0x16 */
|
|
U8 Flags; /* 0x17 */
|
|
U32 PhyInfo; /* 0x18 */
|
|
U8 NegotiatedLinkRate; /* 0x1C */
|
|
U8 Reserved3; /* 0x1D */
|
|
U16 Reserved4; /* 0x1E */
|
|
} MPI2_CONFIG_PAGE_SAS_PHY_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PHY_0,
|
|
Mpi2SasPhyPage0_t, MPI2_POINTER pMpi2SasPhyPage0_t;
|
|
|
|
#define MPI2_SASPHY0_PAGEVERSION (0x03)
|
|
|
|
/* use MPI2_SAS_PRATE_ defines for the ProgrammedLinkRate field */
|
|
|
|
/* use MPI2_SAS_HWRATE_ defines for the HwLinkRate field */
|
|
|
|
/* values for SAS PHY Page 0 Flags field */
|
|
#define MPI2_SAS_PHY0_FLAGS_SGPIO_DIRECT_ATTACH_ENC (0x01)
|
|
|
|
/* use MPI2_SAS_APHYINFO_ defines for AttachedPhyInfo field */
|
|
|
|
/* use MPI2_SAS_NEG_LINK_RATE_ defines for the NegotiatedLinkRate field */
|
|
|
|
/* use MPI2_SAS_PHYINFO_ for the PhyInfo field */
|
|
|
|
|
|
/* SAS PHY Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_1
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U32 InvalidDwordCount; /* 0x0C */
|
|
U32 RunningDisparityErrorCount; /* 0x10 */
|
|
U32 LossDwordSynchCount; /* 0x14 */
|
|
U32 PhyResetProblemCount; /* 0x18 */
|
|
} MPI2_CONFIG_PAGE_SAS_PHY_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PHY_1,
|
|
Mpi2SasPhyPage1_t, MPI2_POINTER pMpi2SasPhyPage1_t;
|
|
|
|
#define MPI2_SASPHY1_PAGEVERSION (0x01)
|
|
|
|
|
|
/* SAS PHY Page 2 */
|
|
|
|
typedef struct _MPI2_SASPHY2_PHY_EVENT
|
|
{
|
|
U8 PhyEventCode; /* 0x00 */
|
|
U8 Reserved1; /* 0x01 */
|
|
U16 Reserved2; /* 0x02 */
|
|
U32 PhyEventInfo; /* 0x04 */
|
|
} MPI2_SASPHY2_PHY_EVENT, MPI2_POINTER PTR_MPI2_SASPHY2_PHY_EVENT,
|
|
Mpi2SasPhy2PhyEvent_t, MPI2_POINTER pMpi2SasPhy2PhyEvent_t;
|
|
|
|
/* use MPI2_SASPHY3_EVENT_CODE_ for the PhyEventCode field */
|
|
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhyEvents at runtime.
|
|
*/
|
|
#ifndef MPI2_SASPHY2_PHY_EVENT_MAX
|
|
#define MPI2_SASPHY2_PHY_EVENT_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_2
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U8 NumPhyEvents; /* 0x0C */
|
|
U8 Reserved2; /* 0x0D */
|
|
U16 Reserved3; /* 0x0E */
|
|
MPI2_SASPHY2_PHY_EVENT PhyEvent[MPI2_SASPHY2_PHY_EVENT_MAX]; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_SAS_PHY_2, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PHY_2,
|
|
Mpi2SasPhyPage2_t, MPI2_POINTER pMpi2SasPhyPage2_t;
|
|
|
|
#define MPI2_SASPHY2_PAGEVERSION (0x00)
|
|
|
|
|
|
/* SAS PHY Page 3 */
|
|
|
|
typedef struct _MPI2_SASPHY3_PHY_EVENT_CONFIG
|
|
{
|
|
U8 PhyEventCode; /* 0x00 */
|
|
U8 Reserved1; /* 0x01 */
|
|
U16 Reserved2; /* 0x02 */
|
|
U8 CounterType; /* 0x04 */
|
|
U8 ThresholdWindow; /* 0x05 */
|
|
U8 TimeUnits; /* 0x06 */
|
|
U8 Reserved3; /* 0x07 */
|
|
U32 EventThreshold; /* 0x08 */
|
|
U16 ThresholdFlags; /* 0x0C */
|
|
U16 Reserved4; /* 0x0E */
|
|
} MPI2_SASPHY3_PHY_EVENT_CONFIG, MPI2_POINTER PTR_MPI2_SASPHY3_PHY_EVENT_CONFIG,
|
|
Mpi2SasPhy3PhyEventConfig_t, MPI2_POINTER pMpi2SasPhy3PhyEventConfig_t;
|
|
|
|
/* values for PhyEventCode field */
|
|
#define MPI2_SASPHY3_EVENT_CODE_NO_EVENT (0x00)
|
|
#define MPI2_SASPHY3_EVENT_CODE_INVALID_DWORD (0x01)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RUNNING_DISPARITY_ERROR (0x02)
|
|
#define MPI2_SASPHY3_EVENT_CODE_LOSS_DWORD_SYNC (0x03)
|
|
#define MPI2_SASPHY3_EVENT_CODE_PHY_RESET_PROBLEM (0x04)
|
|
#define MPI2_SASPHY3_EVENT_CODE_ELASTICITY_BUF_OVERFLOW (0x05)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_ERROR (0x06)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_ADDR_FRAME_ERROR (0x20)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_AC_OPEN_REJECT (0x21)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_AC_OPEN_REJECT (0x22)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_RC_OPEN_REJECT (0x23)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_RC_OPEN_REJECT (0x24)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP_PARTIAL_WAITING_ON (0x25)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP_CONNECT_WAITING_ON (0x26)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_BREAK (0x27)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_BREAK (0x28)
|
|
#define MPI2_SASPHY3_EVENT_CODE_BREAK_TIMEOUT (0x29)
|
|
#define MPI2_SASPHY3_EVENT_CODE_CONNECTION (0x2A)
|
|
#define MPI2_SASPHY3_EVENT_CODE_PEAKTX_PATHWAY_BLOCKED (0x2B)
|
|
#define MPI2_SASPHY3_EVENT_CODE_PEAKTX_ARB_WAIT_TIME (0x2C)
|
|
#define MPI2_SASPHY3_EVENT_CODE_PEAK_ARB_WAIT_TIME (0x2D)
|
|
#define MPI2_SASPHY3_EVENT_CODE_PEAK_CONNECT_TIME (0x2E)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_SSP_FRAMES (0x40)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_SSP_FRAMES (0x41)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_SSP_ERROR_FRAMES (0x42)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_SSP_ERROR_FRAMES (0x43)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_CREDIT_BLOCKED (0x44)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_CREDIT_BLOCKED (0x45)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_SATA_FRAMES (0x50)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_SATA_FRAMES (0x51)
|
|
#define MPI2_SASPHY3_EVENT_CODE_SATA_OVERFLOW (0x52)
|
|
#define MPI2_SASPHY3_EVENT_CODE_TX_SMP_FRAMES (0x60)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_SMP_FRAMES (0x61)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_SMP_ERROR_FRAMES (0x63)
|
|
#define MPI2_SASPHY3_EVENT_CODE_HOTPLUG_TIMEOUT (0xD0)
|
|
#define MPI2_SASPHY3_EVENT_CODE_MISALIGNED_MUX_PRIMITIVE (0xD1)
|
|
#define MPI2_SASPHY3_EVENT_CODE_RX_AIP (0xD2)
|
|
|
|
/* values for the CounterType field */
|
|
#define MPI2_SASPHY3_COUNTER_TYPE_WRAPPING (0x00)
|
|
#define MPI2_SASPHY3_COUNTER_TYPE_SATURATING (0x01)
|
|
#define MPI2_SASPHY3_COUNTER_TYPE_PEAK_VALUE (0x02)
|
|
|
|
/* values for the TimeUnits field */
|
|
#define MPI2_SASPHY3_TIME_UNITS_10_MICROSECONDS (0x00)
|
|
#define MPI2_SASPHY3_TIME_UNITS_100_MICROSECONDS (0x01)
|
|
#define MPI2_SASPHY3_TIME_UNITS_1_MILLISECOND (0x02)
|
|
#define MPI2_SASPHY3_TIME_UNITS_10_MILLISECONDS (0x03)
|
|
|
|
/* values for the ThresholdFlags field */
|
|
#define MPI2_SASPHY3_TFLAGS_PHY_RESET (0x0002)
|
|
#define MPI2_SASPHY3_TFLAGS_EVENT_NOTIFY (0x0001)
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumPhyEvents at runtime.
|
|
*/
|
|
#ifndef MPI2_SASPHY3_PHY_EVENT_MAX
|
|
#define MPI2_SASPHY3_PHY_EVENT_MAX (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_3
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U8 NumPhyEvents; /* 0x0C */
|
|
U8 Reserved2; /* 0x0D */
|
|
U16 Reserved3; /* 0x0E */
|
|
MPI2_SASPHY3_PHY_EVENT_CONFIG PhyEventConfig[MPI2_SASPHY3_PHY_EVENT_MAX]; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_SAS_PHY_3, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PHY_3,
|
|
Mpi2SasPhyPage3_t, MPI2_POINTER pMpi2SasPhyPage3_t;
|
|
|
|
#define MPI2_SASPHY3_PAGEVERSION (0x00)
|
|
|
|
|
|
/* SAS PHY Page 4 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PHY_4
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U16 Reserved1; /* 0x08 */
|
|
U8 Reserved2; /* 0x0A */
|
|
U8 Flags; /* 0x0B */
|
|
U8 InitialFrame[28]; /* 0x0C */
|
|
} MPI2_CONFIG_PAGE_SAS_PHY_4, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PHY_4,
|
|
Mpi2SasPhyPage4_t, MPI2_POINTER pMpi2SasPhyPage4_t;
|
|
|
|
#define MPI2_SASPHY4_PAGEVERSION (0x00)
|
|
|
|
/* values for the Flags field */
|
|
#define MPI2_SASPHY4_FLAGS_FRAME_VALID (0x02)
|
|
#define MPI2_SASPHY4_FLAGS_SATA_FRAME (0x01)
|
|
|
|
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS Port Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS Port Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_PORT_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 PortNumber; /* 0x08 */
|
|
U8 PhysicalPort; /* 0x09 */
|
|
U8 PortWidth; /* 0x0A */
|
|
U8 PhysicalPortWidth; /* 0x0B */
|
|
U8 ZoneGroup; /* 0x0C */
|
|
U8 Reserved1; /* 0x0D */
|
|
U16 Reserved2; /* 0x0E */
|
|
U64 SASAddress; /* 0x10 */
|
|
U32 DeviceInfo; /* 0x18 */
|
|
U32 Reserved3; /* 0x1C */
|
|
U32 Reserved4; /* 0x20 */
|
|
} MPI2_CONFIG_PAGE_SAS_PORT_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_PORT_0,
|
|
Mpi2SasPortPage0_t, MPI2_POINTER pMpi2SasPortPage0_t;
|
|
|
|
#define MPI2_SASPORT0_PAGEVERSION (0x00)
|
|
|
|
/* see mpi2_sas.h for values for SAS Port Page 0 DeviceInfo values */
|
|
|
|
|
|
/****************************************************************************
|
|
* SAS Enclosure Config Pages
|
|
****************************************************************************/
|
|
|
|
/* SAS Enclosure Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U64 EnclosureLogicalID; /* 0x0C */
|
|
U16 Flags; /* 0x14 */
|
|
U16 EnclosureHandle; /* 0x16 */
|
|
U16 NumSlots; /* 0x18 */
|
|
U16 StartSlot; /* 0x1A */
|
|
U16 Reserved2; /* 0x1C */
|
|
U16 SEPDevHandle; /* 0x1E */
|
|
U32 Reserved3; /* 0x20 */
|
|
U32 Reserved4; /* 0x24 */
|
|
} MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_SAS_ENCLOSURE_0,
|
|
Mpi2SasEnclosurePage0_t, MPI2_POINTER pMpi2SasEnclosurePage0_t;
|
|
|
|
#define MPI2_SASENCLOSURE0_PAGEVERSION (0x03)
|
|
|
|
/* values for SAS Enclosure Page 0 Flags field */
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_MASK (0x000F)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_UNKNOWN (0x0000)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_SES (0x0001)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_SGPIO (0x0002)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_EXP_SGPIO (0x0003)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_SES_ENCLOSURE (0x0004)
|
|
#define MPI2_SAS_ENCLS0_FLAGS_MNG_IOC_GPIO (0x0005)
|
|
|
|
|
|
/****************************************************************************
|
|
* Log Config Page
|
|
****************************************************************************/
|
|
|
|
/* Log Page 0 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumLogEntries at runtime.
|
|
*/
|
|
#ifndef MPI2_LOG_0_NUM_LOG_ENTRIES
|
|
#define MPI2_LOG_0_NUM_LOG_ENTRIES (1)
|
|
#endif
|
|
|
|
#define MPI2_LOG_0_LOG_DATA_LENGTH (0x1C)
|
|
|
|
typedef struct _MPI2_LOG_0_ENTRY
|
|
{
|
|
U64 TimeStamp; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U16 LogSequence; /* 0x0C */
|
|
U16 LogEntryQualifier; /* 0x0E */
|
|
U8 VP_ID; /* 0x10 */
|
|
U8 VF_ID; /* 0x11 */
|
|
U16 Reserved2; /* 0x12 */
|
|
U8 LogData[MPI2_LOG_0_LOG_DATA_LENGTH];/* 0x14 */
|
|
} MPI2_LOG_0_ENTRY, MPI2_POINTER PTR_MPI2_LOG_0_ENTRY,
|
|
Mpi2Log0Entry_t, MPI2_POINTER pMpi2Log0Entry_t;
|
|
|
|
/* values for Log Page 0 LogEntry LogEntryQualifier field */
|
|
#define MPI2_LOG_0_ENTRY_QUAL_ENTRY_UNUSED (0x0000)
|
|
#define MPI2_LOG_0_ENTRY_QUAL_POWER_ON_RESET (0x0001)
|
|
#define MPI2_LOG_0_ENTRY_QUAL_TIMESTAMP_UPDATE (0x0002)
|
|
#define MPI2_LOG_0_ENTRY_QUAL_MIN_IMPLEMENT_SPEC (0x8000)
|
|
#define MPI2_LOG_0_ENTRY_QUAL_MAX_IMPLEMENT_SPEC (0xFFFF)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_LOG_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved1; /* 0x08 */
|
|
U32 Reserved2; /* 0x0C */
|
|
U16 NumLogEntries; /* 0x10 */
|
|
U16 Reserved3; /* 0x12 */
|
|
MPI2_LOG_0_ENTRY LogEntry[MPI2_LOG_0_NUM_LOG_ENTRIES]; /* 0x14 */
|
|
} MPI2_CONFIG_PAGE_LOG_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_LOG_0,
|
|
Mpi2LogPage0_t, MPI2_POINTER pMpi2LogPage0_t;
|
|
|
|
#define MPI2_LOG_0_PAGEVERSION (0x02)
|
|
|
|
|
|
/****************************************************************************
|
|
* RAID Config Page
|
|
****************************************************************************/
|
|
|
|
/* RAID Page 0 */
|
|
|
|
/*
|
|
* Host code (drivers, BIOS, utilities, etc.) should leave this define set to
|
|
* one and check the value returned for NumElements at runtime.
|
|
*/
|
|
#ifndef MPI2_RAIDCONFIG0_MAX_ELEMENTS
|
|
#define MPI2_RAIDCONFIG0_MAX_ELEMENTS (1)
|
|
#endif
|
|
|
|
typedef struct _MPI2_RAIDCONFIG0_CONFIG_ELEMENT
|
|
{
|
|
U16 ElementFlags; /* 0x00 */
|
|
U16 VolDevHandle; /* 0x02 */
|
|
U8 HotSparePool; /* 0x04 */
|
|
U8 PhysDiskNum; /* 0x05 */
|
|
U16 PhysDiskDevHandle; /* 0x06 */
|
|
} MPI2_RAIDCONFIG0_CONFIG_ELEMENT,
|
|
MPI2_POINTER PTR_MPI2_RAIDCONFIG0_CONFIG_ELEMENT,
|
|
Mpi2RaidConfig0ConfigElement_t, MPI2_POINTER pMpi2RaidConfig0ConfigElement_t;
|
|
|
|
/* values for the ElementFlags field */
|
|
#define MPI2_RAIDCONFIG0_EFLAGS_MASK_ELEMENT_TYPE (0x000F)
|
|
#define MPI2_RAIDCONFIG0_EFLAGS_VOLUME_ELEMENT (0x0000)
|
|
#define MPI2_RAIDCONFIG0_EFLAGS_VOL_PHYS_DISK_ELEMENT (0x0001)
|
|
#define MPI2_RAIDCONFIG0_EFLAGS_HOT_SPARE_ELEMENT (0x0002)
|
|
#define MPI2_RAIDCONFIG0_EFLAGS_OCE_ELEMENT (0x0003)
|
|
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumHotSpares; /* 0x08 */
|
|
U8 NumPhysDisks; /* 0x09 */
|
|
U8 NumVolumes; /* 0x0A */
|
|
U8 ConfigNum; /* 0x0B */
|
|
U32 Flags; /* 0x0C */
|
|
U8 ConfigGUID[24]; /* 0x10 */
|
|
U32 Reserved1; /* 0x28 */
|
|
U8 NumElements; /* 0x2C */
|
|
U8 Reserved2; /* 0x2D */
|
|
U16 Reserved3; /* 0x2E */
|
|
MPI2_RAIDCONFIG0_CONFIG_ELEMENT ConfigElement[MPI2_RAIDCONFIG0_MAX_ELEMENTS]; /* 0x30 */
|
|
} MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_RAID_CONFIGURATION_0,
|
|
Mpi2RaidConfigurationPage0_t, MPI2_POINTER pMpi2RaidConfigurationPage0_t;
|
|
|
|
#define MPI2_RAIDCONFIG0_PAGEVERSION (0x00)
|
|
|
|
/* values for RAID Configuration Page 0 Flags field */
|
|
#define MPI2_RAIDCONFIG0_FLAG_FOREIGN_CONFIG (0x00000001)
|
|
|
|
|
|
/****************************************************************************
|
|
* Driver Persistent Mapping Config Pages
|
|
****************************************************************************/
|
|
|
|
/* Driver Persistent Mapping Page 0 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY
|
|
{
|
|
U64 PhysicalIdentifier; /* 0x00 */
|
|
U16 MappingInformation; /* 0x08 */
|
|
U16 DeviceIndex; /* 0x0A */
|
|
U32 PhysicalBitsMapping; /* 0x0C */
|
|
U32 Reserved1; /* 0x10 */
|
|
} MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY,
|
|
Mpi2DriverMap0Entry_t, MPI2_POINTER pMpi2DriverMap0Entry_t;
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_DRIVER_MAPPING_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
MPI2_CONFIG_PAGE_DRIVER_MAP0_ENTRY Entry; /* 0x08 */
|
|
} MPI2_CONFIG_PAGE_DRIVER_MAPPING_0,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_DRIVER_MAPPING_0,
|
|
Mpi2DriverMappingPage0_t, MPI2_POINTER pMpi2DriverMappingPage0_t;
|
|
|
|
#define MPI2_DRIVERMAPPING0_PAGEVERSION (0x00)
|
|
|
|
/* values for Driver Persistent Mapping Page 0 MappingInformation field */
|
|
#define MPI2_DRVMAP0_MAPINFO_SLOT_MASK (0x07F0)
|
|
#define MPI2_DRVMAP0_MAPINFO_SLOT_SHIFT (4)
|
|
#define MPI2_DRVMAP0_MAPINFO_MISSING_MASK (0x000F)
|
|
|
|
|
|
/****************************************************************************
|
|
* Ethernet Config Pages
|
|
****************************************************************************/
|
|
|
|
/* Ethernet Page 0 */
|
|
|
|
/* IP address (union of IPv4 and IPv6) */
|
|
typedef union _MPI2_ETHERNET_IP_ADDR
|
|
{
|
|
U32 IPv4Addr;
|
|
U32 IPv6Addr[4];
|
|
} MPI2_ETHERNET_IP_ADDR, MPI2_POINTER PTR_MPI2_ETHERNET_IP_ADDR,
|
|
Mpi2EthernetIpAddr_t, MPI2_POINTER pMpi2EthernetIpAddr_t;
|
|
|
|
#define MPI2_ETHERNET_HOST_NAME_LENGTH (32)
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_ETHERNET_0
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U8 NumInterfaces; /* 0x08 */
|
|
U8 Reserved0; /* 0x09 */
|
|
U16 Reserved1; /* 0x0A */
|
|
U32 Status; /* 0x0C */
|
|
U8 MediaState; /* 0x10 */
|
|
U8 Reserved2; /* 0x11 */
|
|
U16 Reserved3; /* 0x12 */
|
|
U8 MacAddress[6]; /* 0x14 */
|
|
U8 Reserved4; /* 0x1A */
|
|
U8 Reserved5; /* 0x1B */
|
|
MPI2_ETHERNET_IP_ADDR IpAddress; /* 0x1C */
|
|
MPI2_ETHERNET_IP_ADDR SubnetMask; /* 0x2C */
|
|
MPI2_ETHERNET_IP_ADDR GatewayIpAddress; /* 0x3C */
|
|
MPI2_ETHERNET_IP_ADDR DNS1IpAddress; /* 0x4C */
|
|
MPI2_ETHERNET_IP_ADDR DNS2IpAddress; /* 0x5C */
|
|
MPI2_ETHERNET_IP_ADDR DhcpIpAddress; /* 0x6C */
|
|
U8 HostName[MPI2_ETHERNET_HOST_NAME_LENGTH];/* 0x7C */
|
|
} MPI2_CONFIG_PAGE_ETHERNET_0, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_ETHERNET_0,
|
|
Mpi2EthernetPage0_t, MPI2_POINTER pMpi2EthernetPage0_t;
|
|
|
|
#define MPI2_ETHERNETPAGE0_PAGEVERSION (0x00)
|
|
|
|
/* values for Ethernet Page 0 Status field */
|
|
#define MPI2_ETHPG0_STATUS_IPV6_CAPABLE (0x80000000)
|
|
#define MPI2_ETHPG0_STATUS_IPV4_CAPABLE (0x40000000)
|
|
#define MPI2_ETHPG0_STATUS_CONSOLE_CONNECTED (0x20000000)
|
|
#define MPI2_ETHPG0_STATUS_DEFAULT_IF (0x00000100)
|
|
#define MPI2_ETHPG0_STATUS_FW_DWNLD_ENABLED (0x00000080)
|
|
#define MPI2_ETHPG0_STATUS_TELNET_ENABLED (0x00000040)
|
|
#define MPI2_ETHPG0_STATUS_SSH2_ENABLED (0x00000020)
|
|
#define MPI2_ETHPG0_STATUS_DHCP_CLIENT_ENABLED (0x00000010)
|
|
#define MPI2_ETHPG0_STATUS_IPV6_ENABLED (0x00000008)
|
|
#define MPI2_ETHPG0_STATUS_IPV4_ENABLED (0x00000004)
|
|
#define MPI2_ETHPG0_STATUS_IPV6_ADDRESSES (0x00000002)
|
|
#define MPI2_ETHPG0_STATUS_ETH_IF_ENABLED (0x00000001)
|
|
|
|
/* values for Ethernet Page 0 MediaState field */
|
|
#define MPI2_ETHPG0_MS_DUPLEX_MASK (0x80)
|
|
#define MPI2_ETHPG0_MS_HALF_DUPLEX (0x00)
|
|
#define MPI2_ETHPG0_MS_FULL_DUPLEX (0x80)
|
|
|
|
#define MPI2_ETHPG0_MS_CONNECT_SPEED_MASK (0x07)
|
|
#define MPI2_ETHPG0_MS_NOT_CONNECTED (0x00)
|
|
#define MPI2_ETHPG0_MS_10MBIT (0x01)
|
|
#define MPI2_ETHPG0_MS_100MBIT (0x02)
|
|
#define MPI2_ETHPG0_MS_1GBIT (0x03)
|
|
|
|
|
|
/* Ethernet Page 1 */
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_ETHERNET_1
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 Reserved0; /* 0x08 */
|
|
U32 Flags; /* 0x0C */
|
|
U8 MediaState; /* 0x10 */
|
|
U8 Reserved1; /* 0x11 */
|
|
U16 Reserved2; /* 0x12 */
|
|
U8 MacAddress[6]; /* 0x14 */
|
|
U8 Reserved3; /* 0x1A */
|
|
U8 Reserved4; /* 0x1B */
|
|
MPI2_ETHERNET_IP_ADDR StaticIpAddress; /* 0x1C */
|
|
MPI2_ETHERNET_IP_ADDR StaticSubnetMask; /* 0x2C */
|
|
MPI2_ETHERNET_IP_ADDR StaticGatewayIpAddress; /* 0x3C */
|
|
MPI2_ETHERNET_IP_ADDR StaticDNS1IpAddress; /* 0x4C */
|
|
MPI2_ETHERNET_IP_ADDR StaticDNS2IpAddress; /* 0x5C */
|
|
U32 Reserved5; /* 0x6C */
|
|
U32 Reserved6; /* 0x70 */
|
|
U32 Reserved7; /* 0x74 */
|
|
U32 Reserved8; /* 0x78 */
|
|
U8 HostName[MPI2_ETHERNET_HOST_NAME_LENGTH];/* 0x7C */
|
|
} MPI2_CONFIG_PAGE_ETHERNET_1, MPI2_POINTER PTR_MPI2_CONFIG_PAGE_ETHERNET_1,
|
|
Mpi2EthernetPage1_t, MPI2_POINTER pMpi2EthernetPage1_t;
|
|
|
|
#define MPI2_ETHERNETPAGE1_PAGEVERSION (0x00)
|
|
|
|
/* values for Ethernet Page 1 Flags field */
|
|
#define MPI2_ETHPG1_FLAG_SET_DEFAULT_IF (0x00000100)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_FW_DOWNLOAD (0x00000080)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_TELNET (0x00000040)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_SSH2 (0x00000020)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_DHCP_CLIENT (0x00000010)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_IPV6 (0x00000008)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_IPV4 (0x00000004)
|
|
#define MPI2_ETHPG1_FLAG_USE_IPV6_ADDRESSES (0x00000002)
|
|
#define MPI2_ETHPG1_FLAG_ENABLE_ETH_IF (0x00000001)
|
|
|
|
/* values for Ethernet Page 1 MediaState field */
|
|
#define MPI2_ETHPG1_MS_DUPLEX_MASK (0x80)
|
|
#define MPI2_ETHPG1_MS_HALF_DUPLEX (0x00)
|
|
#define MPI2_ETHPG1_MS_FULL_DUPLEX (0x80)
|
|
|
|
#define MPI2_ETHPG1_MS_DATA_RATE_MASK (0x07)
|
|
#define MPI2_ETHPG1_MS_DATA_RATE_AUTO (0x00)
|
|
#define MPI2_ETHPG1_MS_DATA_RATE_10MBIT (0x01)
|
|
#define MPI2_ETHPG1_MS_DATA_RATE_100MBIT (0x02)
|
|
#define MPI2_ETHPG1_MS_DATA_RATE_1GBIT (0x03)
|
|
|
|
|
|
/****************************************************************************
|
|
* Extended Manufacturing Config Pages
|
|
****************************************************************************/
|
|
|
|
/*
|
|
* Generic structure to use for product-specific extended manufacturing pages
|
|
* (currently Extended Manufacturing Page 40 through Extended Manufacturing
|
|
* Page 60).
|
|
*/
|
|
|
|
typedef struct _MPI2_CONFIG_PAGE_EXT_MAN_PS
|
|
{
|
|
MPI2_CONFIG_EXTENDED_PAGE_HEADER Header; /* 0x00 */
|
|
U32 ProductSpecificInfo; /* 0x08 */
|
|
} MPI2_CONFIG_PAGE_EXT_MAN_PS,
|
|
MPI2_POINTER PTR_MPI2_CONFIG_PAGE_EXT_MAN_PS,
|
|
Mpi2ExtManufacturingPagePS_t, MPI2_POINTER pMpi2ExtManufacturingPagePS_t;
|
|
|
|
/* PageVersion should be provided by product-specific code */
|
|
|
|
#endif
|
|
|