cea2b8b915
library: o) Increase inline unit / large function growth limits for MIPS to accommodate the needs of the Simple Executive, which uses a shocking amount of inlining. o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and the Octeon SoC. o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific board numbers, specifically to support the MR320. o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd, which improperly uses an evaluation board's board number and breaks board detection at runtime. This board is sold by Portwell as the CAM-0100. o) Add support for the RTC available on some Octeon boards. o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO ports can not work unless building for n64. o) Clean up the CompactFlash driver to use Simple Executive macros and structures where possible (it would be advisable to use the Simple Executive API to set the PIO mode, too, but that is not done presently.) Also use structures from FreeBSD's ATA layer rather than structures copied from Linux. o) Print available Octeon SoC features on boot. o) Add support for the Octeon timecounter. o) Use the Simple Executive's routines rather than local copies for doing reads and writes to 64-bit addresses and use its macros for various device addresses rather than using local copies. o) Rename octeon_board_real to octeon_is_simulation to reduce differences with Cavium-provided code originally written for Linux. Also make it use the same simplified test that the Simple Executive and Linux both use rather than our complex one. o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus to use normal interrupt allocation and setup routines. o) Use the Simple Executive's bootmem facility to allocate physical memory for the kernel, rather than assuming we know which addresses we can steal. NB: This may reduce the amount of RAM the kernel reports you as having if you are leaving large temporary allocations made by U-Boot allocated when starting FreeBSD. o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes Ethernet interface naming from rgmxN to octeN. The new driver has vast improvements over the old one, both in performance and functionality, but does still have some features which have not been ported entirely and there may be unimplemented code that can be hit in everyday use. I will make every effort to correct those as they are reported. o) Support loading the kernel on non-contiguous cores. o) Add very conservative support for harvesting randomness from the Octeon random number device. o) Turn SMP on by default. o) Clean up the style of the Octeon kernel configurations a little and make them compile with -march=octeon. o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple Executive. o) Modify the Simple Executive to build on FreeBSD and to build without executive-config.h or cvmx-config.h. In the future we may want to revert part of these changes and supply executive-config.h and cvmx-config.h and access to the options contained in those files via kernel configuration files. o) Modify the Simple Executive USB routines to support getting and setting of the USB PID.
111 lines
3.5 KiB
C
111 lines
3.5 KiB
C
/***********************license start***************
|
|
* Copyright (c) 2003-2008 Cavium Networks (support@cavium.com). All rights
|
|
* reserved.
|
|
*
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met:
|
|
*
|
|
* * Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
*
|
|
* * Redistributions in binary form must reproduce the above
|
|
* copyright notice, this list of conditions and the following
|
|
* disclaimer in the documentation and/or other materials provided
|
|
* with the distribution.
|
|
*
|
|
* * Neither the name of Cavium Networks nor the names of
|
|
* its contributors may be used to endorse or promote products
|
|
* derived from this software without specific prior written
|
|
* permission.
|
|
*
|
|
* TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS"
|
|
* AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS
|
|
* OR WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH
|
|
* RESPECT TO THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY
|
|
* REPRESENTATION OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT
|
|
* DEFECTS, AND CAVIUM SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES
|
|
* OF TITLE, MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR
|
|
* PURPOSE, LACK OF VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET
|
|
* POSSESSION OR CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT
|
|
* OF USE OR PERFORMANCE OF THE SOFTWARE LIES WITH YOU.
|
|
*
|
|
*
|
|
* For any questions regarding licensing please contact marketing@caviumnetworks.com
|
|
*
|
|
***********************license end**************************************/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/**
|
|
* @file
|
|
*
|
|
* Functions for LOOP initialization, configuration,
|
|
* and monitoring.
|
|
*
|
|
* <hr>$Revision: 41586 $<hr>
|
|
*/
|
|
#include "cvmx.h"
|
|
#include "cvmx-helper.h"
|
|
|
|
|
|
#ifdef CVMX_ENABLE_PKO_FUNCTIONS
|
|
/**
|
|
* @INTERNAL
|
|
* Probe a LOOP interface and determine the number of ports
|
|
* connected to it. The LOOP interface should still be down
|
|
* after this call.
|
|
*
|
|
* @param interface Interface to probe
|
|
*
|
|
* @return Number of ports on the interface. Zero to disable.
|
|
*/
|
|
int __cvmx_helper_loop_probe(int interface)
|
|
{
|
|
cvmx_ipd_sub_port_fcs_t ipd_sub_port_fcs;
|
|
int num_ports = 4;
|
|
int port;
|
|
|
|
/* We need to disable length checking so packet < 64 bytes and jumbo
|
|
frames don't get errors */
|
|
for (port=0; port<num_ports; port++)
|
|
{
|
|
cvmx_pip_port_cfg_t port_cfg;
|
|
int ipd_port = cvmx_helper_get_ipd_port(interface, port);
|
|
port_cfg.u64 = cvmx_read_csr(CVMX_PIP_PRT_CFGX(ipd_port));
|
|
port_cfg.s.maxerr_en = 0;
|
|
port_cfg.s.minerr_en = 0;
|
|
cvmx_write_csr(CVMX_PIP_PRT_CFGX(ipd_port), port_cfg.u64);
|
|
}
|
|
|
|
/* Disable FCS stripping for loopback ports */
|
|
ipd_sub_port_fcs.u64 = cvmx_read_csr(CVMX_IPD_SUB_PORT_FCS);
|
|
ipd_sub_port_fcs.s.port_bit2 = 0;
|
|
cvmx_write_csr(CVMX_IPD_SUB_PORT_FCS, ipd_sub_port_fcs.u64);
|
|
return num_ports;
|
|
}
|
|
|
|
|
|
/**
|
|
* @INTERNAL
|
|
* Bringup and enable a LOOP interface. After this call packet
|
|
* I/O should be fully functional. This is called with IPD
|
|
* enabled but PKO disabled.
|
|
*
|
|
* @param interface Interface to bring up
|
|
*
|
|
* @return Zero on success, negative on failure
|
|
*/
|
|
int __cvmx_helper_loop_enable(int interface)
|
|
{
|
|
/* Do nothing. */
|
|
return 0;
|
|
}
|
|
|
|
#endif /* CVMX_ENABLE_PKO_FUNCTIONS */
|
|
|