d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
ededc31dd1
freebsd-nq/sys/dev/usb/umass.c
Ian Dowse e0a4f554be Abort any active transfers when the device detaches. This fixes a 
few situations where we used to crash, but by no means all of them.
2005-02-14 02:17:53 +00:00

3148 lines
90 KiB
C
Raw Blame History

/*-
* Copyright (c) 1999 MAEKAWA Masahide <bishop@rr.iij4u.or.jp>,
* Nick Hibma <n_hibma@freebsd.org>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
* $NetBSD: umass.c,v 1.28 2000/04/02 23:46:53 augustss Exp $
*/
/* Also already merged from NetBSD:
* $NetBSD: umass.c,v 1.67 2001/11/25 19:05:22 augustss Exp $
* $NetBSD: umass.c,v 1.90 2002/11/04 19:17:33 pooka Exp $
* $NetBSD: umass.c,v 1.108 2003/11/07 17:03:25 wiz Exp $
* $NetBSD: umass.c,v 1.109 2003/12/04 13:57:31 keihan Exp $
*/
/*
* Universal Serial Bus Mass Storage Class specs:
* http://www.usb.org/developers/devclass_docs/usb_msc_overview_1.2.pdf
* http://www.usb.org/developers/devclass_docs/usbmassbulk_10.pdf
* http://www.usb.org/developers/devclass_docs/usb_msc_cbi_1.1.pdf
* http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf
*/
/*
* Ported to NetBSD by Lennart Augustsson <augustss@NetBSD.org>.
* Parts of the code written by Jason R. Thorpe <thorpej@shagadelic.org>.
*/
/*
* The driver handles 3 Wire Protocols
* - Command/Bulk/Interrupt (CBI)
* - Command/Bulk/Interrupt with Command Completion Interrupt (CBI with CCI)
* - Mass Storage Bulk-Only (BBB)
* (BBB refers Bulk/Bulk/Bulk for Command/Data/Status phases)
*
* Over these wire protocols it handles the following command protocols
* - SCSI
* - UFI (floppy command set)
* - 8070i (ATAPI)
*
* UFI and 8070i (ATAPI) are transformed versions of the SCSI command set. The
* sc->transform method is used to convert the commands into the appropriate
* format (if at all necessary). For example, UFI requires all commands to be
* 12 bytes in length amongst other things.
*
* The source code below is marked and can be split into a number of pieces
* (in this order):
*
* - probe/attach/detach
* - generic transfer routines
* - BBB
* - CBI
* - CBI_I (in addition to functions from CBI)
* - CAM (Common Access Method)
* - SCSI
* - UFI
* - 8070i (ATAPI)
*
* The protocols are implemented using a state machine, for the transfers as
* well as for the resets. The state machine is contained in umass_*_state.
* The state machine is started through either umass_*_transfer or
* umass_*_reset.
*
* The reason for doing this is a) CAM performs a lot better this way and b) it
* avoids using tsleep from interrupt context (for example after a failed
* transfer).
*/
/*
* The SCSI related part of this driver has been derived from the
* dev/ppbus/vpo.c driver, by Nicolas Souchu (nsouch@freebsd.org).
*
* The CAM layer uses so called actions which are messages sent to the host
* adapter for completion. The actions come in through umass_cam_action. The
* appropriate block of routines is called depending on the transport protocol
* in use. When the transfer has finished, these routines call
* umass_cam_cb again to complete the CAM command.
*/
/*
* XXX Currently CBI with CCI is not supported because it bombs the system
* when the device is detached (low frequency interrupts are detached
* too late.
*/
#undef CBI_I
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <sys/sysctl.h>
#include <dev/usb/usb.h>
#include <dev/usb/usbdi.h>
#include <dev/usb/usbdi_util.h>
#include "usbdevs.h"
#include <cam/cam.h>
#include <cam/cam_ccb.h>
#include <cam/cam_sim.h>
#include <cam/cam_xpt_sim.h>
#include <cam/scsi/scsi_all.h>
#include <cam/scsi/scsi_da.h>
#include <cam/cam_periph.h>
#ifdef USB_DEBUG
#define DIF(m, x) if (umassdebug & (m)) do { x ; } while (0)
#define DPRINTF(m, x) if (umassdebug & (m)) logprintf x
#define UDMASS_GEN 0x00010000 /* general */
#define UDMASS_SCSI 0x00020000 /* scsi */
#define UDMASS_UFI 0x00040000 /* ufi command set */
#define UDMASS_ATAPI 0x00080000 /* 8070i command set */
#define UDMASS_CMD (UDMASS_SCSI|UDMASS_UFI|UDMASS_ATAPI)
#define UDMASS_USB 0x00100000 /* USB general */
#define UDMASS_BBB 0x00200000 /* Bulk-Only transfers */
#define UDMASS_CBI 0x00400000 /* CBI transfers */
#define UDMASS_WIRE (UDMASS_BBB|UDMASS_CBI)
#define UDMASS_ALL 0xffff0000 /* all of the above */
int umassdebug = 0;
SYSCTL_NODE(_hw_usb, OID_AUTO, umass, CTLFLAG_RW, 0, "USB umass");
SYSCTL_INT(_hw_usb_umass, OID_AUTO, debug, CTLFLAG_RW,
&umassdebug, 0, "umass debug level");
#else
#define DIF(m, x) /* nop */
#define DPRINTF(m, x) /* nop */
#endif
/* Generic definitions */
/* Direction for umass_*_transfer */
#define DIR_NONE 0
#define DIR_IN 1
#define DIR_OUT 2
/* device name */
#define DEVNAME "umass"
#define DEVNAME_SIM "umass-sim"
#define UMASS_MAX_TRANSFER_SIZE 65536
/* Approximate maximum transfer speeds (assumes 33% overhead). */
#define UMASS_FULL_TRANSFER_SPEED 1000
#define UMASS_HIGH_TRANSFER_SPEED 40000
#define UMASS_FLOPPY_TRANSFER_SPEED 20
#define UMASS_TIMEOUT 5000 /* msecs */
/* CAM specific definitions */
#define UMASS_SCSIID_MAX 1 /* maximum number of drives expected */
#define UMASS_SCSIID_HOST UMASS_SCSIID_MAX
#define MS_TO_TICKS(ms) ((ms) * hz / 1000)
/* Bulk-Only features */
#define UR_BBB_RESET 0xff /* Bulk-Only reset */
#define UR_BBB_GET_MAX_LUN 0xfe /* Get maximum lun */
/* Command Block Wrapper */
typedef struct {
uDWord dCBWSignature;
# define CBWSIGNATURE 0x43425355
uDWord dCBWTag;
uDWord dCBWDataTransferLength;
uByte bCBWFlags;
# define CBWFLAGS_OUT 0x00
# define CBWFLAGS_IN 0x80
uByte bCBWLUN;
uByte bCDBLength;
# define CBWCDBLENGTH 16
uByte CBWCDB[CBWCDBLENGTH];
} umass_bbb_cbw_t;
#define UMASS_BBB_CBW_SIZE 31
/* Command Status Wrapper */
typedef struct {
uDWord dCSWSignature;
# define CSWSIGNATURE 0x53425355
# define CSWSIGNATURE_OLYMPUS_C1 0x55425355
uDWord dCSWTag;
uDWord dCSWDataResidue;
uByte bCSWStatus;
# define CSWSTATUS_GOOD 0x0
# define CSWSTATUS_FAILED 0x1
# define CSWSTATUS_PHASE 0x2
} umass_bbb_csw_t;
#define UMASS_BBB_CSW_SIZE 13
/* CBI features */
#define UR_CBI_ADSC 0x00
typedef unsigned char umass_cbi_cbl_t[16]; /* Command block */
typedef union {
struct {
unsigned char type;
#define IDB_TYPE_CCI 0x00
unsigned char value;
#define IDB_VALUE_PASS 0x00
#define IDB_VALUE_FAIL 0x01
#define IDB_VALUE_PHASE 0x02
#define IDB_VALUE_PERSISTENT 0x03
#define IDB_VALUE_STATUS_MASK 0x03
} common;
struct {
unsigned char asc;
unsigned char ascq;
} ufi;
} umass_cbi_sbl_t;
struct umass_softc; /* see below */
typedef void (*transfer_cb_f) (struct umass_softc *sc, void *priv,
int residue, int status);
#define STATUS_CMD_OK 0 /* everything ok */
#define STATUS_CMD_UNKNOWN 1 /* will have to fetch sense */
#define STATUS_CMD_FAILED 2 /* transfer was ok, command failed */
#define STATUS_WIRE_FAILED 3 /* couldn't even get command across */
typedef void (*wire_reset_f) (struct umass_softc *sc, int status);
typedef void (*wire_transfer_f) (struct umass_softc *sc, int lun,
void *cmd, int cmdlen, void *data, int datalen,
int dir, u_int timeout, transfer_cb_f cb, void *priv);
typedef void (*wire_state_f) (usbd_xfer_handle xfer,
usbd_private_handle priv, usbd_status err);
typedef int (*command_transform_f) (struct umass_softc *sc,
unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen);
struct umass_devdescr_t {
u_int32_t vid;
# define VID_WILDCARD 0xffffffff
# define VID_EOT 0xfffffffe
u_int32_t pid;
# define PID_WILDCARD 0xffffffff
# define PID_EOT 0xfffffffe
u_int32_t rid;
# define RID_WILDCARD 0xffffffff
# define RID_EOT 0xfffffffe
/* wire and command protocol */
u_int16_t proto;
# define UMASS_PROTO_BBB 0x0001 /* USB wire protocol */
# define UMASS_PROTO_CBI 0x0002
# define UMASS_PROTO_CBI_I 0x0004
# define UMASS_PROTO_WIRE 0x00ff /* USB wire protocol mask */
# define UMASS_PROTO_SCSI 0x0100 /* command protocol */
# define UMASS_PROTO_ATAPI 0x0200
# define UMASS_PROTO_UFI 0x0400
# define UMASS_PROTO_RBC 0x0800
# define UMASS_PROTO_COMMAND 0xff00 /* command protocol mask */
/* Device specific quirks */
u_int16_t quirks;
# define NO_QUIRKS 0x0000
/* The drive does not support Test Unit Ready. Convert to Start Unit
*/
# define NO_TEST_UNIT_READY 0x0001
/* The drive does not reset the Unit Attention state after REQUEST
* SENSE has been sent. The INQUIRY command does not reset the UA
* either, and so CAM runs in circles trying to retrieve the initial
* INQUIRY data.
*/
# define RS_NO_CLEAR_UA 0x0002
/* The drive does not support START STOP. */
# define NO_START_STOP 0x0004
/* Don't ask for full inquiry data (255b). */
# define FORCE_SHORT_INQUIRY 0x0008
/* Needs to be initialised the Shuttle way */
# define SHUTTLE_INIT 0x0010
/* Drive needs to be switched to alternate iface 1 */
# define ALT_IFACE_1 0x0020
/* Drive does not do 1Mb/s, but just floppy speeds (20kb/s) */
# define FLOPPY_SPEED 0x0040
/* The device can't count and gets the residue of transfers wrong */
# define IGNORE_RESIDUE 0x0080
/* No GetMaxLun call */
# define NO_GETMAXLUN 0x0100
/* The device uses a weird CSWSIGNATURE. */
# define WRONG_CSWSIG 0x0200
/* Device cannot handle INQUIRY so fake a generic response */
# define NO_INQUIRY 0x0400
/* Device cannot handle INQUIRY EVPD, return CHECK CONDITION */
# define NO_INQUIRY_EVPD 0x0800
};
Static struct umass_devdescr_t umass_devdescrs[] = {
{ USB_VENDOR_ASAHIOPTICAL, PID_WILDCARD, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
RS_NO_CLEAR_UA
},
{ USB_VENDOR_FUJIPHOTO, USB_PRODUCT_FUJIPHOTO_MASS0100, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
RS_NO_CLEAR_UA
},
{ USB_VENDOR_GENESYS, USB_PRODUCT_GENESYS_GL641USB2IDE, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY | NO_START_STOP | IGNORE_RESIDUE
},
{ USB_VENDOR_GENESYS, USB_PRODUCT_GENESYS_GL641USB2IDE_2, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY | NO_START_STOP | IGNORE_RESIDUE
},
{ USB_VENDOR_GENESYS, USB_PRODUCT_GENESYS_GL641USB, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY | NO_START_STOP | IGNORE_RESIDUE
},
{ USB_VENDOR_HITACHI, USB_PRODUCT_HITACHI_DVDCAM_USB, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
NO_INQUIRY
},
{ USB_VENDOR_HP, USB_PRODUCT_HP_CDW8200, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
NO_TEST_UNIT_READY | NO_START_STOP
},
{ USB_VENDOR_INSYSTEM, USB_PRODUCT_INSYSTEM_USBCABLE, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI,
NO_TEST_UNIT_READY | NO_START_STOP | ALT_IFACE_1
},
{ USB_VENDOR_IODATA, USB_PRODUCT_IODATA_IU_CD2, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_IODATA, USB_PRODUCT_IODATA_DVR_UEH8, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_IOMEGA, USB_PRODUCT_IOMEGA_ZIP100, RID_WILDCARD,
/* XXX This is not correct as there are Zip drives that use ATAPI.
*/
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_TEST_UNIT_READY
},
{ USB_VENDOR_LOGITEC, USB_PRODUCT_LOGITEC_LDR_H443SU2, RID_WILDCARD,
UMASS_PROTO_SCSI,
NO_QUIRKS
},
{ USB_VENDOR_LOGITEC, USB_PRODUCT_LOGITEC_LDR_H443U2, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_MELCO, USB_PRODUCT_MELCO_DUBPXXG, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY | NO_START_STOP | IGNORE_RESIDUE
},
{ USB_VENDOR_MICROTECH, USB_PRODUCT_MICROTECH_DPCM, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_CBI,
NO_TEST_UNIT_READY | NO_START_STOP
},
{ USB_VENDOR_MSYSTEMS, USB_PRODUCT_MSYSTEMS_DISKONKEY, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
IGNORE_RESIDUE | NO_GETMAXLUN | RS_NO_CLEAR_UA
},
{ USB_VENDOR_MSYSTEMS, USB_PRODUCT_MSYSTEMS_DISKONKEY2, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_NEODIO, USB_PRODUCT_NEODIO_ND3260, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY
},
{ USB_VENDOR_OLYMPUS, USB_PRODUCT_OLYMPUS_C1, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
WRONG_CSWSIG
},
{ USB_VENDOR_ONSPEC, USB_PRODUCT_ONSPEC_UCF100, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_BBB,
NO_INQUIRY | NO_GETMAXLUN
},
{ USB_VENDOR_PANASONIC, USB_PRODUCT_PANASONIC_KXLCB20AN, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_PANASONIC, USB_PRODUCT_PANASONIC_KXLCB35AN, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_PLEXTOR, USB_PRODUCT_PLEXTOR_40_12_40U, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_TEST_UNIT_READY
},
{ USB_VENDOR_PNY, USB_PRODUCT_PNY_ATTACHE, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
IGNORE_RESIDUE
},
{ USB_VENDOR_SANDISK, USB_PRODUCT_SANDISK_SDCZ2_256, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
IGNORE_RESIDUE
},
{ USB_VENDOR_SCANLOGIC, USB_PRODUCT_SCANLOGIC_SL11R, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_BBB,
NO_INQUIRY
},
{ USB_VENDOR_SHUTTLE, USB_PRODUCT_SHUTTLE_EUSB, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
NO_TEST_UNIT_READY | NO_START_STOP | SHUTTLE_INIT
},
{ USB_VENDOR_SIGMATEL, USB_PRODUCT_SIGMATEL_I_BEAD100, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
SHUTTLE_INIT
},
{ USB_VENDOR_SIIG, USB_PRODUCT_SIIG_WINTERREADER, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
IGNORE_RESIDUE
},
{ USB_VENDOR_SONY, USB_PRODUCT_SONY_DSC, RID_WILDCARD,
UMASS_PROTO_RBC | UMASS_PROTO_CBI,
NO_QUIRKS
},
{ USB_VENDOR_SONY, USB_PRODUCT_SONY_HANDYCAM, RID_WILDCARD,
UMASS_PROTO_RBC | UMASS_PROTO_CBI,
NO_QUIRKS
},
{ USB_VENDOR_SONY, USB_PRODUCT_SONY_MSC, RID_WILDCARD,
UMASS_PROTO_RBC | UMASS_PROTO_CBI,
NO_QUIRKS
},
{ USB_VENDOR_TREK, USB_PRODUCT_TREK_THUMBDRIVE_8MB, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_BBB,
IGNORE_RESIDUE
},
{ USB_VENDOR_TRUMPION, USB_PRODUCT_TRUMPION_C3310, RID_WILDCARD,
UMASS_PROTO_UFI | UMASS_PROTO_CBI,
NO_QUIRKS
},
{ USB_VENDOR_TWINMOS, USB_PRODUCT_TWINMOS_MDIV, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
NO_QUIRKS
},
{ USB_VENDOR_WESTERN, USB_PRODUCT_WESTERN_EXTHDD, RID_WILDCARD,
UMASS_PROTO_SCSI | UMASS_PROTO_BBB,
FORCE_SHORT_INQUIRY | NO_START_STOP | IGNORE_RESIDUE
},
{ USB_VENDOR_YANO, USB_PRODUCT_YANO_U640MO, RID_WILDCARD,
UMASS_PROTO_ATAPI | UMASS_PROTO_CBI_I,
FORCE_SHORT_INQUIRY
},
{ VID_EOT, PID_EOT, RID_EOT, 0, 0 }
};
/* the per device structure */
struct umass_softc {
USBBASEDEVICE sc_dev; /* base device */
usbd_device_handle sc_udev; /* USB device */
struct cam_sim *umass_sim; /* SCSI Interface Module */
unsigned char flags; /* various device flags */
# define UMASS_FLAGS_GONE 0x01 /* devices is no more */
u_int16_t proto; /* wire and cmd protocol */
u_int16_t quirks; /* they got it almost right */
usbd_interface_handle iface; /* Mass Storage interface */
int ifaceno; /* MS iface number */
u_int8_t bulkin; /* bulk-in Endpoint Address */
u_int8_t bulkout; /* bulk-out Endpoint Address */
u_int8_t intrin; /* intr-in Endp. (CBI) */
usbd_pipe_handle bulkin_pipe;
usbd_pipe_handle bulkout_pipe;
usbd_pipe_handle intrin_pipe;
/* Reset the device in a wire protocol specific way */
wire_reset_f reset;
/* The start of a wire transfer. It prepares the whole transfer (cmd,
* data, and status stage) and initiates it. It is up to the state
* machine (below) to handle the various stages and errors in these
*/
wire_transfer_f transfer;
/* The state machine, handling the various states during a transfer */
wire_state_f state;
/* The command transform function is used to conver the SCSI commands
* into their derivatives, like UFI, ATAPI, and friends.
*/
command_transform_f transform; /* command transform */
/* Bulk specific variables for transfers in progress */
umass_bbb_cbw_t cbw; /* command block wrapper */
umass_bbb_csw_t csw; /* command status wrapper*/
/* CBI specific variables for transfers in progress */
umass_cbi_cbl_t cbl; /* command block */
umass_cbi_sbl_t sbl; /* status block */
/* generic variables for transfers in progress */
/* ctrl transfer requests */
usb_device_request_t request;
/* xfer handles
* Most of our operations are initiated from interrupt context, so
* we need to avoid using the one that is in use. We want to avoid
* allocating them in the interrupt context as well.
*/
/* indices into array below */
# define XFER_BBB_CBW 0 /* Bulk-Only */
# define XFER_BBB_DATA 1
# define XFER_BBB_DCLEAR 2
# define XFER_BBB_CSW1 3
# define XFER_BBB_CSW2 4
# define XFER_BBB_SCLEAR 5
# define XFER_BBB_RESET1 6
# define XFER_BBB_RESET2 7
# define XFER_BBB_RESET3 8
# define XFER_CBI_CB 0 /* CBI */
# define XFER_CBI_DATA 1
# define XFER_CBI_STATUS 2
# define XFER_CBI_DCLEAR 3
# define XFER_CBI_SCLEAR 4
# define XFER_CBI_RESET1 5
# define XFER_CBI_RESET2 6
# define XFER_CBI_RESET3 7
# define XFER_NR 9 /* maximum number */
usbd_xfer_handle transfer_xfer[XFER_NR]; /* for ctrl xfers */
int transfer_dir; /* data direction */
void *transfer_data; /* data buffer */
int transfer_datalen; /* (maximum) length */
int transfer_actlen; /* actual length */
transfer_cb_f transfer_cb; /* callback */
void *transfer_priv; /* for callback */
int transfer_status;
int transfer_state;
# define TSTATE_ATTACH 0 /* in attach */
# define TSTATE_IDLE 1
# define TSTATE_BBB_COMMAND 2 /* CBW transfer */
# define TSTATE_BBB_DATA 3 /* Data transfer */
# define TSTATE_BBB_DCLEAR 4 /* clear endpt stall */
# define TSTATE_BBB_STATUS1 5 /* clear endpt stall */
# define TSTATE_BBB_SCLEAR 6 /* clear endpt stall */
# define TSTATE_BBB_STATUS2 7 /* CSW transfer */
# define TSTATE_BBB_RESET1 8 /* reset command */
# define TSTATE_BBB_RESET2 9 /* in clear stall */
# define TSTATE_BBB_RESET3 10 /* out clear stall */
# define TSTATE_CBI_COMMAND 11 /* command transfer */
# define TSTATE_CBI_DATA 12 /* data transfer */
# define TSTATE_CBI_STATUS 13 /* status transfer */
# define TSTATE_CBI_DCLEAR 14 /* clear ep stall */
# define TSTATE_CBI_SCLEAR 15 /* clear ep stall */
# define TSTATE_CBI_RESET1 16 /* reset command */
# define TSTATE_CBI_RESET2 17 /* in clear stall */
# define TSTATE_CBI_RESET3 18 /* out clear stall */
# define TSTATE_STATES 19 /* # of states above */
/* SCSI/CAM specific variables */
unsigned char cam_scsi_command[CAM_MAX_CDBLEN];
unsigned char cam_scsi_command2[CAM_MAX_CDBLEN];
struct scsi_sense cam_scsi_sense;
struct scsi_sense cam_scsi_test_unit_ready;
usb_callout_t cam_scsi_rescan_ch;
int timeout; /* in msecs */
int maxlun; /* maximum LUN number */
};
#ifdef USB_DEBUG
char *states[TSTATE_STATES+1] = {
/* should be kept in sync with the list at transfer_state */
"Attach",
"Idle",
"BBB CBW",
"BBB Data",
"BBB Data bulk-in/-out clear stall",
"BBB CSW, 1st attempt",
"BBB CSW bulk-in clear stall",
"BBB CSW, 2nd attempt",
"BBB Reset",
"BBB bulk-in clear stall",
"BBB bulk-out clear stall",
"CBI Command",
"CBI Data",
"CBI Status",
"CBI Data bulk-in/-out clear stall",
"CBI Status intr-in clear stall",
"CBI Reset",
"CBI bulk-in clear stall",
"CBI bulk-out clear stall",
NULL
};
#endif
/* If device cannot return valid inquiry data, fake it */
Static uint8_t fake_inq_data[SHORT_INQUIRY_LENGTH] = {
0, /*removable*/ 0x80, SCSI_REV_2, SCSI_REV_2,
/*additional_length*/ 31, 0, 0, 0
};
/* USB device probe/attach/detach functions */
USB_DECLARE_DRIVER(umass);
Static int umass_match_proto (struct umass_softc *sc,
usbd_interface_handle iface,
usbd_device_handle udev);
/* quirk functions */
Static void umass_init_shuttle (struct umass_softc *sc);
/* generic transfer functions */
Static usbd_status umass_setup_transfer (struct umass_softc *sc,
usbd_pipe_handle pipe,
void *buffer, int buflen, int flags,
usbd_xfer_handle xfer);
Static usbd_status umass_setup_ctrl_transfer (struct umass_softc *sc,
usbd_device_handle udev,
usb_device_request_t *req,
void *buffer, int buflen, int flags,
usbd_xfer_handle xfer);
Static void umass_clear_endpoint_stall (struct umass_softc *sc,
u_int8_t endpt, usbd_pipe_handle pipe,
int state, usbd_xfer_handle xfer);
Static void umass_reset (struct umass_softc *sc,
transfer_cb_f cb, void *priv);
/* Bulk-Only related functions */
Static void umass_bbb_reset (struct umass_softc *sc, int status);
Static void umass_bbb_transfer (struct umass_softc *sc, int lun,
void *cmd, int cmdlen,
void *data, int datalen, int dir, u_int timeout,
transfer_cb_f cb, void *priv);
Static void umass_bbb_state (usbd_xfer_handle xfer,
usbd_private_handle priv,
usbd_status err);
Static int umass_bbb_get_max_lun
(struct umass_softc *sc);
/* CBI related functions */
Static int umass_cbi_adsc (struct umass_softc *sc,
char *buffer, int buflen,
usbd_xfer_handle xfer);
Static void umass_cbi_reset (struct umass_softc *sc, int status);
Static void umass_cbi_transfer (struct umass_softc *sc, int lun,
void *cmd, int cmdlen,
void *data, int datalen, int dir, u_int timeout,
transfer_cb_f cb, void *priv);
Static void umass_cbi_state (usbd_xfer_handle xfer,
usbd_private_handle priv, usbd_status err);
/* CAM related functions */
Static void umass_cam_action (struct cam_sim *sim, union ccb *ccb);
Static void umass_cam_poll (struct cam_sim *sim);
Static void umass_cam_cb (struct umass_softc *sc, void *priv,
int residue, int status);
Static void umass_cam_sense_cb (struct umass_softc *sc, void *priv,
int residue, int status);
Static void umass_cam_quirk_cb (struct umass_softc *sc, void *priv,
int residue, int status);
Static void umass_cam_rescan_callback
(struct cam_periph *periph,union ccb *ccb);
Static void umass_cam_rescan (void *addr);
Static int umass_cam_attach_sim (struct umass_softc *sc);
Static int umass_cam_attach (struct umass_softc *sc);
Static int umass_cam_detach_sim (struct umass_softc *sc);
/* SCSI specific functions */
Static int umass_scsi_transform (struct umass_softc *sc,
unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen);
/* UFI specific functions */
#define UFI_COMMAND_LENGTH 12 /* UFI commands are always 12 bytes */
Static int umass_ufi_transform (struct umass_softc *sc,
unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen);
/* ATAPI (8070i) specific functions */
#define ATAPI_COMMAND_LENGTH 12 /* ATAPI commands are always 12 bytes */
Static int umass_atapi_transform (struct umass_softc *sc,
unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen);
/* RBC specific functions */
Static int umass_rbc_transform (struct umass_softc *sc,
unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen);
#ifdef USB_DEBUG
/* General debugging functions */
Static void umass_bbb_dump_cbw (struct umass_softc *sc, umass_bbb_cbw_t *cbw);
Static void umass_bbb_dump_csw (struct umass_softc *sc, umass_bbb_csw_t *csw);
Static void umass_cbi_dump_cmd (struct umass_softc *sc, void *cmd, int cmdlen);
Static void umass_dump_buffer (struct umass_softc *sc, u_int8_t *buffer,
int buflen, int printlen);
#endif
#if defined(__FreeBSD__)
MODULE_DEPEND(umass, cam, 1,1,1);
#endif
/*
* USB device probe/attach/detach
*/
/*
* Match the device we are seeing with the devices supported. Fill in the
* description in the softc accordingly. This function is called from both
* probe and attach.
*/
Static int
umass_match_proto(struct umass_softc *sc, usbd_interface_handle iface,
usbd_device_handle udev)
{
usb_device_descriptor_t *dd;
usb_interface_descriptor_t *id;
int i;
int found = 0;
sc->sc_udev = udev;
sc->proto = 0;
sc->quirks = 0;
dd = usbd_get_device_descriptor(udev);
/* An entry specifically for Y-E Data devices as they don't fit in the
* device description table.
*/
if (UGETW(dd->idVendor) == USB_VENDOR_YEDATA
&& UGETW(dd->idProduct) == USB_PRODUCT_YEDATA_FLASHBUSTERU) {
/* Revisions < 1.28 do not handle the interrupt endpoint
* very well.
*/
if (UGETW(dd->bcdDevice) < 0x128) {
sc->proto = UMASS_PROTO_UFI | UMASS_PROTO_CBI;
} else {
sc->proto = UMASS_PROTO_UFI | UMASS_PROTO_CBI_I;
}
/*
* Revisions < 1.28 do not have the TEST UNIT READY command
* Revisions == 1.28 have a broken TEST UNIT READY
*/
if (UGETW(dd->bcdDevice) <= 0x128)
sc->quirks |= NO_TEST_UNIT_READY;
sc->quirks |= RS_NO_CLEAR_UA | FLOPPY_SPEED;
return(UMATCH_VENDOR_PRODUCT);
}
/* Check the list of supported devices for a match. While looking,
* check for wildcarded and fully matched. First match wins.
*/
for (i = 0; umass_devdescrs[i].vid != VID_EOT && !found; i++) {
if (umass_devdescrs[i].vid == VID_WILDCARD &&
umass_devdescrs[i].pid == PID_WILDCARD &&
umass_devdescrs[i].rid == RID_WILDCARD) {
printf("umass: ignoring invalid wildcard quirk\n");
continue;
}
if ((umass_devdescrs[i].vid == UGETW(dd->idVendor) ||
umass_devdescrs[i].vid == VID_WILDCARD)
&& (umass_devdescrs[i].pid == UGETW(dd->idProduct) ||
umass_devdescrs[i].pid == PID_WILDCARD)) {
if (umass_devdescrs[i].rid == RID_WILDCARD) {
sc->proto = umass_devdescrs[i].proto;
sc->quirks = umass_devdescrs[i].quirks;
return (UMATCH_VENDOR_PRODUCT);
} else if (umass_devdescrs[i].rid ==
UGETW(dd->bcdDevice)) {
sc->proto = umass_devdescrs[i].proto;
sc->quirks = umass_devdescrs[i].quirks;
return (UMATCH_VENDOR_PRODUCT_REV);
} /* else RID does not match */
}
}
/* Check for a standards compliant device */
id = usbd_get_interface_descriptor(iface);
if (id == NULL || id->bInterfaceClass != UICLASS_MASS)
return(UMATCH_NONE);
switch (id->bInterfaceSubClass) {
case UISUBCLASS_SCSI:
sc->proto |= UMASS_PROTO_SCSI;
break;
case UISUBCLASS_UFI:
sc->proto |= UMASS_PROTO_UFI;
break;
case UISUBCLASS_RBC:
sc->proto |= UMASS_PROTO_RBC;
break;
case UISUBCLASS_SFF8020I:
case UISUBCLASS_SFF8070I:
sc->proto |= UMASS_PROTO_ATAPI;
break;
default:
DPRINTF(UDMASS_GEN, ("%s: Unsupported command protocol %d\n",
USBDEVNAME(sc->sc_dev), id->bInterfaceSubClass));
return(UMATCH_NONE);
}
switch (id->bInterfaceProtocol) {
case UIPROTO_MASS_CBI:
sc->proto |= UMASS_PROTO_CBI;
break;
case UIPROTO_MASS_CBI_I:
sc->proto |= UMASS_PROTO_CBI_I;
break;
case UIPROTO_MASS_BBB_OLD:
case UIPROTO_MASS_BBB:
sc->proto |= UMASS_PROTO_BBB;
break;
default:
DPRINTF(UDMASS_GEN, ("%s: Unsupported wire protocol %d\n",
USBDEVNAME(sc->sc_dev), id->bInterfaceProtocol));
return(UMATCH_NONE);
}
return(UMATCH_DEVCLASS_DEVSUBCLASS_DEVPROTO);
}
USB_MATCH(umass)
{
USB_MATCH_START(umass, uaa);
struct umass_softc *sc = device_get_softc(self);
USB_MATCH_SETUP;
if (uaa->iface == NULL)
return(UMATCH_NONE);
return(umass_match_proto(sc, uaa->iface, uaa->device));
}
USB_ATTACH(umass)
{
USB_ATTACH_START(umass, sc, uaa);
usb_interface_descriptor_t *id;
usb_endpoint_descriptor_t *ed;
char devinfo[1024];
int i;
int err;
/*
* the softc struct is bzero-ed in device_set_driver. We can safely
* call umass_detach without specifically initialising the struct.
*/
usbd_devinfo(uaa->device, 0, devinfo);
USB_ATTACH_SETUP;
sc->iface = uaa->iface;
sc->ifaceno = uaa->ifaceno;
usb_callout_init(sc->cam_scsi_rescan_ch);
/* initialise the proto and drive values in the umass_softc (again) */
(void) umass_match_proto(sc, sc->iface, uaa->device);
id = usbd_get_interface_descriptor(sc->iface);
#ifdef USB_DEBUG
printf("%s: ", USBDEVNAME(sc->sc_dev));
switch (sc->proto&UMASS_PROTO_COMMAND) {
case UMASS_PROTO_SCSI:
printf("SCSI");
break;
case UMASS_PROTO_ATAPI:
printf("8070i (ATAPI)");
break;
case UMASS_PROTO_UFI:
printf("UFI");
break;
case UMASS_PROTO_RBC:
printf("RBC");
break;
default:
printf("(unknown 0x%02x)", sc->proto&UMASS_PROTO_COMMAND);
break;
}
printf(" over ");
switch (sc->proto&UMASS_PROTO_WIRE) {
case UMASS_PROTO_BBB:
printf("Bulk-Only");
break;
case UMASS_PROTO_CBI: /* uses Comand/Bulk pipes */
printf("CBI");
break;
case UMASS_PROTO_CBI_I: /* uses Comand/Bulk/Interrupt pipes */
printf("CBI with CCI");
#ifndef CBI_I
printf(" (using CBI)");
#endif
break;
default:
printf("(unknown 0x%02x)", sc->proto&UMASS_PROTO_WIRE);
}
printf("; quirks = 0x%04x\n", sc->quirks);
#endif
#ifndef CBI_I
if (sc->proto & UMASS_PROTO_CBI_I) {
/* See beginning of file for comment on the use of CBI with CCI */
sc->proto = (sc->proto & ~UMASS_PROTO_CBI_I) | UMASS_PROTO_CBI;
}
#endif
if (sc->quirks & ALT_IFACE_1) {
err = usbd_set_interface(0, 1);
if (err) {
DPRINTF(UDMASS_USB, ("%s: could not switch to "
"Alt Interface %d\n",
USBDEVNAME(sc->sc_dev), 1));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
}
/*
* In addition to the Control endpoint the following endpoints
* are required:
* a) bulk-in endpoint.
* b) bulk-out endpoint.
* and for Control/Bulk/Interrupt with CCI (CBI_I)
* c) intr-in
*
* The endpoint addresses are not fixed, so we have to read them
* from the device descriptors of the current interface.
*/
for (i = 0 ; i < id->bNumEndpoints ; i++) {
ed = usbd_interface2endpoint_descriptor(sc->iface, i);
if (!ed) {
printf("%s: could not read endpoint descriptor\n",
USBDEVNAME(sc->sc_dev));
USB_ATTACH_ERROR_RETURN;
}
if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN
&& (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) {
sc->bulkin = ed->bEndpointAddress;
} else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_OUT
&& (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) {
sc->bulkout = ed->bEndpointAddress;
} else if (sc->proto & UMASS_PROTO_CBI_I
&& UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN
&& (ed->bmAttributes & UE_XFERTYPE) == UE_INTERRUPT) {
sc->intrin = ed->bEndpointAddress;
#ifdef USB_DEBUG
if (UGETW(ed->wMaxPacketSize) > 2) {
DPRINTF(UDMASS_CBI, ("%s: intr size is %d\n",
USBDEVNAME(sc->sc_dev),
UGETW(ed->wMaxPacketSize)));
}
#endif
}
}
/* check whether we found all the endpoints we need */
if (!sc->bulkin || !sc->bulkout
|| (sc->proto & UMASS_PROTO_CBI_I && !sc->intrin) ) {
DPRINTF(UDMASS_USB, ("%s: endpoint not found %d/%d/%d\n",
USBDEVNAME(sc->sc_dev),
sc->bulkin, sc->bulkout, sc->intrin));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
/* Open the bulk-in and -out pipe */
err = usbd_open_pipe(sc->iface, sc->bulkout,
USBD_EXCLUSIVE_USE, &sc->bulkout_pipe);
if (err) {
DPRINTF(UDMASS_USB, ("%s: cannot open %d-out pipe (bulk)\n",
USBDEVNAME(sc->sc_dev), sc->bulkout));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
err = usbd_open_pipe(sc->iface, sc->bulkin,
USBD_EXCLUSIVE_USE, &sc->bulkin_pipe);
if (err) {
DPRINTF(UDMASS_USB, ("%s: could not open %d-in pipe (bulk)\n",
USBDEVNAME(sc->sc_dev), sc->bulkin));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
/* Open the intr-in pipe if the protocol is CBI with CCI.
* Note: early versions of the Zip drive do have an interrupt pipe, but
* this pipe is unused.
*
* We do not open the interrupt pipe as an interrupt pipe, but as a
* normal bulk endpoint. We send an IN transfer down the wire at the
* appropriate time, because we know exactly when to expect data on
* that endpoint. This saves bandwidth, but more important, makes the
* code for handling the data on that endpoint simpler. No data
* arriving concurrently.
*/
if (sc->proto & UMASS_PROTO_CBI_I) {
err = usbd_open_pipe(sc->iface, sc->intrin,
USBD_EXCLUSIVE_USE, &sc->intrin_pipe);
if (err) {
DPRINTF(UDMASS_USB, ("%s: couldn't open %d-in (intr)\n",
USBDEVNAME(sc->sc_dev), sc->intrin));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
}
/* initialisation of generic part */
sc->transfer_state = TSTATE_ATTACH;
/* request a sufficient number of xfer handles */
for (i = 0; i < XFER_NR; i++) {
sc->transfer_xfer[i] = usbd_alloc_xfer(uaa->device);
if (!sc->transfer_xfer[i]) {
DPRINTF(UDMASS_USB, ("%s: Out of memory\n",
USBDEVNAME(sc->sc_dev)));
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
}
/* Initialise the wire protocol specific methods */
if (sc->proto & UMASS_PROTO_BBB) {
sc->reset = umass_bbb_reset;
sc->transfer = umass_bbb_transfer;
sc->state = umass_bbb_state;
} else if (sc->proto & (UMASS_PROTO_CBI|UMASS_PROTO_CBI_I)) {
sc->reset = umass_cbi_reset;
sc->transfer = umass_cbi_transfer;
sc->state = umass_cbi_state;
#ifdef USB_DEBUG
} else {
panic("%s:%d: Unknown proto 0x%02x",
__FILE__, __LINE__, sc->proto);
#endif
}
if (sc->proto & UMASS_PROTO_SCSI)
sc->transform = umass_scsi_transform;
else if (sc->proto & UMASS_PROTO_UFI)
sc->transform = umass_ufi_transform;
else if (sc->proto & UMASS_PROTO_ATAPI)
sc->transform = umass_atapi_transform;
else if (sc->proto & UMASS_PROTO_RBC)
sc->transform = umass_rbc_transform;
#ifdef USB_DEBUG
else
panic("No transformation defined for command proto 0x%02x",
sc->proto & UMASS_PROTO_COMMAND);
#endif
/* From here onwards the device can be used. */
if (sc->quirks & SHUTTLE_INIT)
umass_init_shuttle(sc);
/* Get the maximum LUN supported by the device.
*/
if ((sc->proto & UMASS_PROTO_WIRE) == UMASS_PROTO_BBB)
sc->maxlun = umass_bbb_get_max_lun(sc);
else
sc->maxlun = 0;
if ((sc->proto & UMASS_PROTO_SCSI) ||
(sc->proto & UMASS_PROTO_ATAPI) ||
(sc->proto & UMASS_PROTO_UFI) ||
(sc->proto & UMASS_PROTO_RBC)) {
/* Prepare the SCSI command block */
sc->cam_scsi_sense.opcode = REQUEST_SENSE;
sc->cam_scsi_test_unit_ready.opcode = TEST_UNIT_READY;
/* register the SIM */
err = umass_cam_attach_sim(sc);
if (err) {
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
/* scan the new sim */
err = umass_cam_attach(sc);
if (err) {
umass_cam_detach_sim(sc);
umass_detach(self);
USB_ATTACH_ERROR_RETURN;
}
} else {
panic("%s:%d: Unknown proto 0x%02x",
__FILE__, __LINE__, sc->proto);
}
sc->transfer_state = TSTATE_IDLE;
DPRINTF(UDMASS_GEN, ("%s: Attach finished\n", USBDEVNAME(sc->sc_dev)));
USB_ATTACH_SUCCESS_RETURN;
}
USB_DETACH(umass)
{
USB_DETACH_START(umass, sc);
int err = 0;
int i;
DPRINTF(UDMASS_USB, ("%s: detached\n", USBDEVNAME(sc->sc_dev)));
sc->flags |= UMASS_FLAGS_GONE;
/* abort all the pipes in case there are transfers active. */
usbd_abort_default_pipe(sc->sc_udev);
if (sc->bulkout_pipe)
usbd_abort_pipe(sc->bulkout_pipe);
if (sc->bulkin_pipe)
usbd_abort_pipe(sc->bulkin_pipe);
if (sc->intrin_pipe)
usbd_abort_pipe(sc->intrin_pipe);
usb_uncallout_drain(sc->cam_scsi_rescan_ch, umass_cam_rescan, sc);
if ((sc->proto & UMASS_PROTO_SCSI) ||
(sc->proto & UMASS_PROTO_ATAPI) ||
(sc->proto & UMASS_PROTO_UFI) ||
(sc->proto & UMASS_PROTO_RBC))
/* detach the SCSI host controller (SIM) */
err = umass_cam_detach_sim(sc);
for (i = 0; i < XFER_NR; i++)
if (sc->transfer_xfer[i])
usbd_free_xfer(sc->transfer_xfer[i]);
/* remove all the pipes */
if (sc->bulkout_pipe)
usbd_close_pipe(sc->bulkout_pipe);
if (sc->bulkin_pipe)
usbd_close_pipe(sc->bulkin_pipe);
if (sc->intrin_pipe)
usbd_close_pipe(sc->intrin_pipe);
return(err);
}
Static void
umass_init_shuttle(struct umass_softc *sc)
{
usb_device_request_t req;
u_char status[2];
/* The Linux driver does this, but no one can tell us what the
* command does.
*/
req.bmRequestType = UT_READ_VENDOR_DEVICE;
req.bRequest = 1; /* XXX unknown command */
USETW(req.wValue, 0);
USETW(req.wIndex, sc->ifaceno);
USETW(req.wLength, sizeof status);
(void) usbd_do_request(sc->sc_udev, &req, &status);
DPRINTF(UDMASS_GEN, ("%s: Shuttle init returned 0x%02x%02x\n",
USBDEVNAME(sc->sc_dev), status[0], status[1]));
}
/*
* Generic functions to handle transfers
*/
Static usbd_status
umass_setup_transfer(struct umass_softc *sc, usbd_pipe_handle pipe,
void *buffer, int buflen, int flags,
usbd_xfer_handle xfer)
{
usbd_status err;
/* Initialise a USB transfer and then schedule it */
(void) usbd_setup_xfer(xfer, pipe, (void *) sc, buffer, buflen, flags,
sc->timeout, sc->state);
err = usbd_transfer(xfer);
if (err && err != USBD_IN_PROGRESS) {
DPRINTF(UDMASS_BBB, ("%s: failed to setup transfer, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err)));
return(err);
}
return (USBD_NORMAL_COMPLETION);
}
Static usbd_status
umass_setup_ctrl_transfer(struct umass_softc *sc, usbd_device_handle udev,
usb_device_request_t *req,
void *buffer, int buflen, int flags,
usbd_xfer_handle xfer)
{
usbd_status err;
/* Initialise a USB control transfer and then schedule it */
(void) usbd_setup_default_xfer(xfer, udev, (void *) sc,
sc->timeout, req, buffer, buflen, flags, sc->state);
err = usbd_transfer(xfer);
if (err && err != USBD_IN_PROGRESS) {
DPRINTF(UDMASS_BBB, ("%s: failed to setup ctrl transfer, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err)));
/* do not reset, as this would make us loop */
return(err);
}
return (USBD_NORMAL_COMPLETION);
}
Static void
umass_clear_endpoint_stall(struct umass_softc *sc,
u_int8_t endpt, usbd_pipe_handle pipe,
int state, usbd_xfer_handle xfer)
{
usbd_device_handle udev;
DPRINTF(UDMASS_BBB, ("%s: Clear endpoint 0x%02x stall\n",
USBDEVNAME(sc->sc_dev), endpt));
usbd_interface2device_handle(sc->iface, &udev);
sc->transfer_state = state;
usbd_clear_endpoint_toggle(pipe);
sc->request.bmRequestType = UT_WRITE_ENDPOINT;
sc->request.bRequest = UR_CLEAR_FEATURE;
USETW(sc->request.wValue, UF_ENDPOINT_HALT);
USETW(sc->request.wIndex, endpt);
USETW(sc->request.wLength, 0);
umass_setup_ctrl_transfer(sc, udev, &sc->request, NULL, 0, 0, xfer);
}
Static void
umass_reset(struct umass_softc *sc, transfer_cb_f cb, void *priv)
{
sc->transfer_cb = cb;
sc->transfer_priv = priv;
/* The reset is a forced reset, so no error (yet) */
sc->reset(sc, STATUS_CMD_OK);
}
/*
* Bulk protocol specific functions
*/
Static void
umass_bbb_reset(struct umass_softc *sc, int status)
{
usbd_device_handle udev;
KASSERT(sc->proto & UMASS_PROTO_BBB,
("%s: umass_bbb_reset: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/*
* Reset recovery (5.3.4 in Universal Serial Bus Mass Storage Class)
*
* For Reset Recovery the host shall issue in the following order:
* a) a Bulk-Only Mass Storage Reset
* b) a Clear Feature HALT to the Bulk-In endpoint
* c) a Clear Feature HALT to the Bulk-Out endpoint
*
* This is done in 3 steps, states:
* TSTATE_BBB_RESET1
* TSTATE_BBB_RESET2
* TSTATE_BBB_RESET3
*
* If the reset doesn't succeed, the device should be port reset.
*/
DPRINTF(UDMASS_BBB, ("%s: Bulk Reset\n",
USBDEVNAME(sc->sc_dev)));
sc->transfer_state = TSTATE_BBB_RESET1;
sc->transfer_status = status;
usbd_interface2device_handle(sc->iface, &udev);
/* reset is a class specific interface write */
sc->request.bmRequestType = UT_WRITE_CLASS_INTERFACE;
sc->request.bRequest = UR_BBB_RESET;
USETW(sc->request.wValue, 0);
USETW(sc->request.wIndex, sc->ifaceno);
USETW(sc->request.wLength, 0);
umass_setup_ctrl_transfer(sc, udev, &sc->request, NULL, 0, 0,
sc->transfer_xfer[XFER_BBB_RESET1]);
}
Static void
umass_bbb_transfer(struct umass_softc *sc, int lun, void *cmd, int cmdlen,
void *data, int datalen, int dir, u_int timeout,
transfer_cb_f cb, void *priv)
{
KASSERT(sc->proto & UMASS_PROTO_BBB,
("%s: umass_bbb_transfer: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/* Be a little generous. */
sc->timeout = timeout + UMASS_TIMEOUT;
/*
* Do a Bulk-Only transfer with cmdlen bytes from cmd, possibly
* a data phase of datalen bytes from/to the device and finally a
* csw read phase.
* If the data direction was inbound a maximum of datalen bytes
* is stored in the buffer pointed to by data.
*
* umass_bbb_transfer initialises the transfer and lets the state
* machine in umass_bbb_state handle the completion. It uses the
* following states:
* TSTATE_BBB_COMMAND
* -> TSTATE_BBB_DATA
* -> TSTATE_BBB_STATUS
* -> TSTATE_BBB_STATUS2
* -> TSTATE_BBB_IDLE
*
* An error in any of those states will invoke
* umass_bbb_reset.
*/
/* check the given arguments */
KASSERT(datalen == 0 || data != NULL,
("%s: datalen > 0, but no buffer",USBDEVNAME(sc->sc_dev)));
KASSERT(cmdlen <= CBWCDBLENGTH,
("%s: cmdlen exceeds CDB length in CBW (%d > %d)",
USBDEVNAME(sc->sc_dev), cmdlen, CBWCDBLENGTH));
KASSERT(dir == DIR_NONE || datalen > 0,
("%s: datalen == 0 while direction is not NONE\n",
USBDEVNAME(sc->sc_dev)));
KASSERT(datalen == 0 || dir != DIR_NONE,
("%s: direction is NONE while datalen is not zero\n",
USBDEVNAME(sc->sc_dev)));
KASSERT(sizeof(umass_bbb_cbw_t) == UMASS_BBB_CBW_SIZE,
("%s: CBW struct does not have the right size (%ld vs. %d)\n",
USBDEVNAME(sc->sc_dev),
(long)sizeof(umass_bbb_cbw_t), UMASS_BBB_CBW_SIZE));
KASSERT(sizeof(umass_bbb_csw_t) == UMASS_BBB_CSW_SIZE,
("%s: CSW struct does not have the right size (%ld vs. %d)\n",
USBDEVNAME(sc->sc_dev),
(long)sizeof(umass_bbb_csw_t), UMASS_BBB_CSW_SIZE));
/*
* Determine the direction of the data transfer and the length.
*
* dCBWDataTransferLength (datalen) :
* This field indicates the number of bytes of data that the host
* intends to transfer on the IN or OUT Bulk endpoint(as indicated by
* the Direction bit) during the execution of this command. If this
* field is set to 0, the device will expect that no data will be
* transferred IN or OUT during this command, regardless of the value
* of the Direction bit defined in dCBWFlags.
*
* dCBWFlags (dir) :
* The bits of the Flags field are defined as follows:
* Bits 0-6 reserved
* Bit 7 Direction - this bit shall be ignored if the
* dCBWDataTransferLength field is zero.
* 0 = data Out from host to device
* 1 = data In from device to host
*/
/* Fill in the Command Block Wrapper
* We fill in all the fields, so there is no need to bzero it first.
*/
USETDW(sc->cbw.dCBWSignature, CBWSIGNATURE);
/* We don't care about the initial value, as long as the values are unique */
USETDW(sc->cbw.dCBWTag, UGETDW(sc->cbw.dCBWTag) + 1);
USETDW(sc->cbw.dCBWDataTransferLength, datalen);
/* DIR_NONE is treated as DIR_OUT (0x00) */
sc->cbw.bCBWFlags = (dir == DIR_IN? CBWFLAGS_IN:CBWFLAGS_OUT);
sc->cbw.bCBWLUN = lun;
sc->cbw.bCDBLength = cmdlen;
bcopy(cmd, sc->cbw.CBWCDB, cmdlen);
DIF(UDMASS_BBB, umass_bbb_dump_cbw(sc, &sc->cbw));
/* store the details for the data transfer phase */
sc->transfer_dir = dir;
sc->transfer_data = data;
sc->transfer_datalen = datalen;
sc->transfer_actlen = 0;
sc->transfer_cb = cb;
sc->transfer_priv = priv;
sc->transfer_status = STATUS_CMD_OK;
/* move from idle to the command state */
sc->transfer_state = TSTATE_BBB_COMMAND;
/* Send the CBW from host to device via bulk-out endpoint. */
if (umass_setup_transfer(sc, sc->bulkout_pipe,
&sc->cbw, UMASS_BBB_CBW_SIZE, 0,
sc->transfer_xfer[XFER_BBB_CBW])) {
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
}
}
Static void
umass_bbb_state(usbd_xfer_handle xfer, usbd_private_handle priv,
usbd_status err)
{
struct umass_softc *sc = (struct umass_softc *) priv;
usbd_xfer_handle next_xfer;
KASSERT(sc->proto & UMASS_PROTO_BBB,
("%s: umass_bbb_state: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/*
* State handling for BBB transfers.
*
* The subroutine is rather long. It steps through the states given in
* Annex A of the Bulk-Only specification.
* Each state first does the error handling of the previous transfer
* and then prepares the next transfer.
* Each transfer is done asynchronously so after the request/transfer
* has been submitted you will find a 'return;'.
*/
DPRINTF(UDMASS_BBB, ("%s: Handling BBB state %d (%s), xfer=%p, %s\n",
USBDEVNAME(sc->sc_dev), sc->transfer_state,
states[sc->transfer_state], xfer, usbd_errstr(err)));
/* Give up if the device has detached. */
if (sc->flags & UMASS_FLAGS_GONE) {
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv, sc->transfer_datalen,
STATUS_CMD_FAILED);
return;
}
switch (sc->transfer_state) {
/***** Bulk Transfer *****/
case TSTATE_BBB_COMMAND:
/* Command transport phase, error handling */
if (err) {
DPRINTF(UDMASS_BBB, ("%s: failed to send CBW\n",
USBDEVNAME(sc->sc_dev)));
/* If the device detects that the CBW is invalid, then
* the device may STALL both bulk endpoints and require
* a Bulk-Reset
*/
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
}
/* Data transport phase, setup transfer */
sc->transfer_state = TSTATE_BBB_DATA;
if (sc->transfer_dir == DIR_IN) {
if (umass_setup_transfer(sc, sc->bulkin_pipe,
sc->transfer_data, sc->transfer_datalen,
USBD_SHORT_XFER_OK,
sc->transfer_xfer[XFER_BBB_DATA]))
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
} else if (sc->transfer_dir == DIR_OUT) {
if (umass_setup_transfer(sc, sc->bulkout_pipe,
sc->transfer_data, sc->transfer_datalen,
0, /* fixed length transfer */
sc->transfer_xfer[XFER_BBB_DATA]))
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
} else {
DPRINTF(UDMASS_BBB, ("%s: no data phase\n",
USBDEVNAME(sc->sc_dev)));
}
/* FALLTHROUGH if no data phase, err == 0 */
case TSTATE_BBB_DATA:
/* Command transport phase, error handling (ignored if no data
* phase (fallthrough from previous state)) */
if (sc->transfer_dir != DIR_NONE) {
/* retrieve the length of the transfer that was done */
usbd_get_xfer_status(xfer, NULL, NULL,
&sc->transfer_actlen, NULL);
if (err) {
DPRINTF(UDMASS_BBB, ("%s: Data-%s %db failed, "
"%s\n", USBDEVNAME(sc->sc_dev),
(sc->transfer_dir == DIR_IN?"in":"out"),
sc->transfer_datalen,usbd_errstr(err)));
if (err == USBD_STALLED) {
umass_clear_endpoint_stall(sc,
(sc->transfer_dir == DIR_IN?
sc->bulkin:sc->bulkout),
(sc->transfer_dir == DIR_IN?
sc->bulkin_pipe:sc->bulkout_pipe),
TSTATE_BBB_DCLEAR,
sc->transfer_xfer[XFER_BBB_DCLEAR]);
return;
} else {
/* Unless the error is a pipe stall the
* error is fatal.
*/
umass_bbb_reset(sc,STATUS_WIRE_FAILED);
return;
}
}
}
DIF(UDMASS_BBB, if (sc->transfer_dir == DIR_IN)
umass_dump_buffer(sc, sc->transfer_data,
sc->transfer_datalen, 48));
/* FALLTHROUGH, err == 0 (no data phase or successfull) */
case TSTATE_BBB_DCLEAR: /* stall clear after data phase */
case TSTATE_BBB_SCLEAR: /* stall clear after status phase */
/* Reading of CSW after bulk stall condition in data phase
* (TSTATE_BBB_DATA2) or bulk-in stall condition after
* reading CSW (TSTATE_BBB_SCLEAR).
* In the case of no data phase or successfull data phase,
* err == 0 and the following if block is passed.
*/
if (err) { /* should not occur */
/* try the transfer below, even if clear stall failed */
DPRINTF(UDMASS_BBB, ("%s: bulk-%s stall clear failed"
", %s\n", USBDEVNAME(sc->sc_dev),
(sc->transfer_dir == DIR_IN? "in":"out"),
usbd_errstr(err)));
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
}
/* Status transport phase, setup transfer */
if (sc->transfer_state == TSTATE_BBB_COMMAND ||
sc->transfer_state == TSTATE_BBB_DATA ||
sc->transfer_state == TSTATE_BBB_DCLEAR) {
/* After no data phase, successfull data phase and
* after clearing bulk-in/-out stall condition
*/
sc->transfer_state = TSTATE_BBB_STATUS1;
next_xfer = sc->transfer_xfer[XFER_BBB_CSW1];
} else {
/* After first attempt of fetching CSW */
sc->transfer_state = TSTATE_BBB_STATUS2;
next_xfer = sc->transfer_xfer[XFER_BBB_CSW2];
}
/* Read the Command Status Wrapper via bulk-in endpoint. */
if (umass_setup_transfer(sc, sc->bulkin_pipe,
&sc->csw, UMASS_BBB_CSW_SIZE, 0,
next_xfer)) {
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
}
return;
case TSTATE_BBB_STATUS1: /* first attempt */
case TSTATE_BBB_STATUS2: /* second attempt */
/* Status transfer, error handling */
if (err) {
DPRINTF(UDMASS_BBB, ("%s: Failed to read CSW, %s%s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err),
(sc->transfer_state == TSTATE_BBB_STATUS1?
", retrying":"")));
/* If this was the first attempt at fetching the CSW
* retry it, otherwise fail.
*/
if (sc->transfer_state == TSTATE_BBB_STATUS1) {
umass_clear_endpoint_stall(sc,
sc->bulkin, sc->bulkin_pipe,
TSTATE_BBB_SCLEAR,
sc->transfer_xfer[XFER_BBB_SCLEAR]);
return;
} else {
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
}
}
DIF(UDMASS_BBB, umass_bbb_dump_csw(sc, &sc->csw));
/* Translate weird command-status signatures. */
if ((sc->quirks & WRONG_CSWSIG) &&
UGETDW(sc->csw.dCSWSignature) == CSWSIGNATURE_OLYMPUS_C1)
USETDW(sc->csw.dCSWSignature, CSWSIGNATURE);
int Residue;
Residue = UGETDW(sc->csw.dCSWDataResidue);
if (Residue == 0 &&
sc->transfer_datalen - sc->transfer_actlen != 0)
Residue = sc->transfer_datalen - sc->transfer_actlen;
/* Check CSW and handle any error */
if (UGETDW(sc->csw.dCSWSignature) != CSWSIGNATURE) {
/* Invalid CSW: Wrong signature or wrong tag might
* indicate that the device is confused -> reset it.
*/
printf("%s: Invalid CSW: sig 0x%08x should be 0x%08x\n",
USBDEVNAME(sc->sc_dev),
UGETDW(sc->csw.dCSWSignature),
CSWSIGNATURE);
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
} else if (UGETDW(sc->csw.dCSWTag)
!= UGETDW(sc->cbw.dCBWTag)) {
printf("%s: Invalid CSW: tag %d should be %d\n",
USBDEVNAME(sc->sc_dev),
UGETDW(sc->csw.dCSWTag),
UGETDW(sc->cbw.dCBWTag));
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
/* CSW is valid here */
} else if (sc->csw.bCSWStatus > CSWSTATUS_PHASE) {
printf("%s: Invalid CSW: status %d > %d\n",
USBDEVNAME(sc->sc_dev),
sc->csw.bCSWStatus,
CSWSTATUS_PHASE);
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
} else if (sc->csw.bCSWStatus == CSWSTATUS_PHASE) {
printf("%s: Phase Error, residue = %d\n",
USBDEVNAME(sc->sc_dev), Residue);
umass_bbb_reset(sc, STATUS_WIRE_FAILED);
return;
} else if (sc->transfer_actlen > sc->transfer_datalen) {
/* Buffer overrun! Don't let this go by unnoticed */
panic("%s: transferred %db instead of %db",
USBDEVNAME(sc->sc_dev),
sc->transfer_actlen, sc->transfer_datalen);
} else if (sc->csw.bCSWStatus == CSWSTATUS_FAILED) {
DPRINTF(UDMASS_BBB, ("%s: Command Failed, res = %d\n",
USBDEVNAME(sc->sc_dev), Residue));
/* SCSI command failed but transfer was succesful */
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv, Residue,
STATUS_CMD_FAILED);
return;
} else { /* success */
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv, Residue,
STATUS_CMD_OK);
return;
}
/***** Bulk Reset *****/
case TSTATE_BBB_RESET1:
if (err)
printf("%s: BBB reset failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
umass_clear_endpoint_stall(sc,
sc->bulkin, sc->bulkin_pipe, TSTATE_BBB_RESET2,
sc->transfer_xfer[XFER_BBB_RESET2]);
return;
case TSTATE_BBB_RESET2:
if (err) /* should not occur */
printf("%s: BBB bulk-in clear stall failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* no error recovery, otherwise we end up in a loop */
umass_clear_endpoint_stall(sc,
sc->bulkout, sc->bulkout_pipe, TSTATE_BBB_RESET3,
sc->transfer_xfer[XFER_BBB_RESET3]);
return;
case TSTATE_BBB_RESET3:
if (err) /* should not occur */
printf("%s: BBB bulk-out clear stall failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* no error recovery, otherwise we end up in a loop */
sc->transfer_state = TSTATE_IDLE;
if (sc->transfer_priv) {
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen,
sc->transfer_status);
}
return;
/***** Default *****/
default:
panic("%s: Unknown state %d",
USBDEVNAME(sc->sc_dev), sc->transfer_state);
}
}
Static int
umass_bbb_get_max_lun(struct umass_softc *sc)
{
usbd_device_handle udev;
usb_device_request_t req;
usbd_status err;
usb_interface_descriptor_t *id;
int maxlun = 0;
u_int8_t buf = 0;
usbd_interface2device_handle(sc->iface, &udev);
id = usbd_get_interface_descriptor(sc->iface);
/* The Get Max Lun command is a class-specific request. */
req.bmRequestType = UT_READ_CLASS_INTERFACE;
req.bRequest = UR_BBB_GET_MAX_LUN;
USETW(req.wValue, 0);
USETW(req.wIndex, id->bInterfaceNumber);
USETW(req.wLength, 1);
err = usbd_do_request(udev, &req, &buf);
switch (err) {
case USBD_NORMAL_COMPLETION:
maxlun = buf;
DPRINTF(UDMASS_BBB, ("%s: Max Lun is %d\n",
USBDEVNAME(sc->sc_dev), maxlun));
break;
case USBD_STALLED:
case USBD_SHORT_XFER:
default:
/* Device doesn't support Get Max Lun request. */
printf("%s: Get Max Lun not supported (%s)\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* XXX Should we port_reset the device? */
break;
}
return(maxlun);
}
/*
* Command/Bulk/Interrupt (CBI) specific functions
*/
Static int
umass_cbi_adsc(struct umass_softc *sc, char *buffer, int buflen,
usbd_xfer_handle xfer)
{
usbd_device_handle udev;
KASSERT(sc->proto & (UMASS_PROTO_CBI|UMASS_PROTO_CBI_I),
("%s: umass_cbi_adsc: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
usbd_interface2device_handle(sc->iface, &udev);
sc->request.bmRequestType = UT_WRITE_CLASS_INTERFACE;
sc->request.bRequest = UR_CBI_ADSC;
USETW(sc->request.wValue, 0);
USETW(sc->request.wIndex, sc->ifaceno);
USETW(sc->request.wLength, buflen);
return umass_setup_ctrl_transfer(sc, udev, &sc->request, buffer,
buflen, 0, xfer);
}
Static void
umass_cbi_reset(struct umass_softc *sc, int status)
{
int i;
# define SEND_DIAGNOSTIC_CMDLEN 12
KASSERT(sc->proto & (UMASS_PROTO_CBI|UMASS_PROTO_CBI_I),
("%s: umass_cbi_reset: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/*
* Command Block Reset Protocol
*
* First send a reset request to the device. Then clear
* any possibly stalled bulk endpoints.
*
* This is done in 3 steps, states:
* TSTATE_CBI_RESET1
* TSTATE_CBI_RESET2
* TSTATE_CBI_RESET3
*
* If the reset doesn't succeed, the device should be port reset.
*/
DPRINTF(UDMASS_CBI, ("%s: CBI Reset\n",
USBDEVNAME(sc->sc_dev)));
KASSERT(sizeof(sc->cbl) >= SEND_DIAGNOSTIC_CMDLEN,
("%s: CBL struct is too small (%ld < %d)\n",
USBDEVNAME(sc->sc_dev),
(long)sizeof(sc->cbl), SEND_DIAGNOSTIC_CMDLEN));
sc->transfer_state = TSTATE_CBI_RESET1;
sc->transfer_status = status;
/* The 0x1d code is the SEND DIAGNOSTIC command. To distinguish between
* the two the last 10 bytes of the cbl is filled with 0xff (section
* 2.2 of the CBI spec).
*/
sc->cbl[0] = 0x1d; /* Command Block Reset */
sc->cbl[1] = 0x04;
for (i = 2; i < SEND_DIAGNOSTIC_CMDLEN; i++)
sc->cbl[i] = 0xff;
umass_cbi_adsc(sc, sc->cbl, SEND_DIAGNOSTIC_CMDLEN,
sc->transfer_xfer[XFER_CBI_RESET1]);
/* XXX if the command fails we should reset the port on the hub */
}
Static void
umass_cbi_transfer(struct umass_softc *sc, int lun,
void *cmd, int cmdlen, void *data, int datalen, int dir,
u_int timeout, transfer_cb_f cb, void *priv)
{
KASSERT(sc->proto & (UMASS_PROTO_CBI|UMASS_PROTO_CBI_I),
("%s: umass_cbi_transfer: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/* Be a little generous. */
sc->timeout = timeout + UMASS_TIMEOUT;
/*
* Do a CBI transfer with cmdlen bytes from cmd, possibly
* a data phase of datalen bytes from/to the device and finally a
* csw read phase.
* If the data direction was inbound a maximum of datalen bytes
* is stored in the buffer pointed to by data.
*
* umass_cbi_transfer initialises the transfer and lets the state
* machine in umass_cbi_state handle the completion. It uses the
* following states:
* TSTATE_CBI_COMMAND
* -> XXX fill in
*
* An error in any of those states will invoke
* umass_cbi_reset.
*/
/* check the given arguments */
KASSERT(datalen == 0 || data != NULL,
("%s: datalen > 0, but no buffer",USBDEVNAME(sc->sc_dev)));
KASSERT(datalen == 0 || dir != DIR_NONE,
("%s: direction is NONE while datalen is not zero\n",
USBDEVNAME(sc->sc_dev)));
/* store the details for the data transfer phase */
sc->transfer_dir = dir;
sc->transfer_data = data;
sc->transfer_datalen = datalen;
sc->transfer_actlen = 0;
sc->transfer_cb = cb;
sc->transfer_priv = priv;
sc->transfer_status = STATUS_CMD_OK;
/* move from idle to the command state */
sc->transfer_state = TSTATE_CBI_COMMAND;
DIF(UDMASS_CBI, umass_cbi_dump_cmd(sc, cmd, cmdlen));
/* Send the Command Block from host to device via control endpoint. */
if (umass_cbi_adsc(sc, cmd, cmdlen, sc->transfer_xfer[XFER_CBI_CB]))
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
Static void
umass_cbi_state(usbd_xfer_handle xfer, usbd_private_handle priv,
usbd_status err)
{
struct umass_softc *sc = (struct umass_softc *) priv;
KASSERT(sc->proto & (UMASS_PROTO_CBI|UMASS_PROTO_CBI_I),
("%s: umass_cbi_state: wrong sc->proto 0x%02x\n",
USBDEVNAME(sc->sc_dev), sc->proto));
/*
* State handling for CBI transfers.
*/
DPRINTF(UDMASS_CBI, ("%s: Handling CBI state %d (%s), xfer=%p, %s\n",
USBDEVNAME(sc->sc_dev), sc->transfer_state,
states[sc->transfer_state], xfer, usbd_errstr(err)));
/* Give up if the device has detached. */
if (sc->flags & UMASS_FLAGS_GONE) {
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv, sc->transfer_datalen,
STATUS_CMD_FAILED);
return;
}
switch (sc->transfer_state) {
/***** CBI Transfer *****/
case TSTATE_CBI_COMMAND:
if (err == USBD_STALLED) {
DPRINTF(UDMASS_CBI, ("%s: Command Transport failed\n",
USBDEVNAME(sc->sc_dev)));
/* Status transport by control pipe (section 2.3.2.1).
* The command contained in the command block failed.
*
* The control pipe has already been unstalled by the
* USB stack.
* Section 2.4.3.1.1 states that the bulk in endpoints
* should not be stalled at this point.
*/
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen,
STATUS_CMD_FAILED);
return;
} else if (err) {
DPRINTF(UDMASS_CBI, ("%s: failed to send ADSC\n",
USBDEVNAME(sc->sc_dev)));
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
return;
}
sc->transfer_state = TSTATE_CBI_DATA;
if (sc->transfer_dir == DIR_IN) {
if (umass_setup_transfer(sc, sc->bulkin_pipe,
sc->transfer_data, sc->transfer_datalen,
USBD_SHORT_XFER_OK,
sc->transfer_xfer[XFER_CBI_DATA]))
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
} else if (sc->transfer_dir == DIR_OUT) {
if (umass_setup_transfer(sc, sc->bulkout_pipe,
sc->transfer_data, sc->transfer_datalen,
0, /* fixed length transfer */
sc->transfer_xfer[XFER_CBI_DATA]))
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
} else if (sc->proto & UMASS_PROTO_CBI_I) {
DPRINTF(UDMASS_CBI, ("%s: no data phase\n",
USBDEVNAME(sc->sc_dev)));
sc->transfer_state = TSTATE_CBI_STATUS;
if (umass_setup_transfer(sc, sc->intrin_pipe,
&sc->sbl, sizeof(sc->sbl),
0, /* fixed length transfer */
sc->transfer_xfer[XFER_CBI_STATUS])){
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
} else {
DPRINTF(UDMASS_CBI, ("%s: no data phase\n",
USBDEVNAME(sc->sc_dev)));
/* No command completion interrupt. Request
* sense data.
*/
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
0, STATUS_CMD_UNKNOWN);
}
return;
case TSTATE_CBI_DATA:
/* retrieve the length of the transfer that was done */
usbd_get_xfer_status(xfer,NULL,NULL,&sc->transfer_actlen,NULL);
if (err) {
DPRINTF(UDMASS_CBI, ("%s: Data-%s %db failed, "
"%s\n", USBDEVNAME(sc->sc_dev),
(sc->transfer_dir == DIR_IN?"in":"out"),
sc->transfer_datalen,usbd_errstr(err)));
if (err == USBD_STALLED) {
umass_clear_endpoint_stall(sc,
sc->bulkin, sc->bulkin_pipe,
TSTATE_CBI_DCLEAR,
sc->transfer_xfer[XFER_CBI_DCLEAR]);
} else {
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
return;
}
DIF(UDMASS_CBI, if (sc->transfer_dir == DIR_IN)
umass_dump_buffer(sc, sc->transfer_data,
sc->transfer_actlen, 48));
if (sc->proto & UMASS_PROTO_CBI_I) {
sc->transfer_state = TSTATE_CBI_STATUS;
if (umass_setup_transfer(sc, sc->intrin_pipe,
&sc->sbl, sizeof(sc->sbl),
0, /* fixed length transfer */
sc->transfer_xfer[XFER_CBI_STATUS])){
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
} else {
/* No command completion interrupt. Request
* sense to get status of command.
*/
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen - sc->transfer_actlen,
STATUS_CMD_UNKNOWN);
}
return;
case TSTATE_CBI_STATUS:
if (err) {
DPRINTF(UDMASS_CBI, ("%s: Status Transport failed\n",
USBDEVNAME(sc->sc_dev)));
/* Status transport by interrupt pipe (section 2.3.2.2).
*/
if (err == USBD_STALLED) {
umass_clear_endpoint_stall(sc,
sc->intrin, sc->intrin_pipe,
TSTATE_CBI_SCLEAR,
sc->transfer_xfer[XFER_CBI_SCLEAR]);
} else {
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
return;
}
/* Dissect the information in the buffer */
if (sc->proto & UMASS_PROTO_UFI) {
int status;
/* Section 3.4.3.1.3 specifies that the UFI command
* protocol returns an ASC and ASCQ in the interrupt
* data block.
*/
DPRINTF(UDMASS_CBI, ("%s: UFI CCI, ASC = 0x%02x, "
"ASCQ = 0x%02x\n",
USBDEVNAME(sc->sc_dev),
sc->sbl.ufi.asc, sc->sbl.ufi.ascq));
if (sc->sbl.ufi.asc == 0 && sc->sbl.ufi.ascq == 0)
status = STATUS_CMD_OK;
else
status = STATUS_CMD_FAILED;
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen - sc->transfer_actlen,
status);
} else {
/* Command Interrupt Data Block */
DPRINTF(UDMASS_CBI, ("%s: type=0x%02x, value=0x%02x\n",
USBDEVNAME(sc->sc_dev),
sc->sbl.common.type, sc->sbl.common.value));
if (sc->sbl.common.type == IDB_TYPE_CCI) {
int err;
if ((sc->sbl.common.value&IDB_VALUE_STATUS_MASK)
== IDB_VALUE_PASS) {
err = STATUS_CMD_OK;
} else if ((sc->sbl.common.value & IDB_VALUE_STATUS_MASK)
== IDB_VALUE_FAIL ||
(sc->sbl.common.value & IDB_VALUE_STATUS_MASK)
== IDB_VALUE_PERSISTENT) {
err = STATUS_CMD_FAILED;
} else {
err = STATUS_WIRE_FAILED;
}
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen-sc->transfer_actlen,
err);
}
}
return;
case TSTATE_CBI_DCLEAR:
if (err) { /* should not occur */
printf("%s: CBI bulk-in/out stall clear failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
umass_cbi_reset(sc, STATUS_WIRE_FAILED);
}
sc->transfer_state = TSTATE_IDLE;
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen,
STATUS_CMD_FAILED);
return;
case TSTATE_CBI_SCLEAR:
if (err) /* should not occur */
printf("%s: CBI intr-in stall clear failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* Something really bad is going on. Reset the device */
umass_cbi_reset(sc, STATUS_CMD_FAILED);
return;
/***** CBI Reset *****/
case TSTATE_CBI_RESET1:
if (err)
printf("%s: CBI reset failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
umass_clear_endpoint_stall(sc,
sc->bulkin, sc->bulkin_pipe, TSTATE_CBI_RESET2,
sc->transfer_xfer[XFER_CBI_RESET2]);
return;
case TSTATE_CBI_RESET2:
if (err) /* should not occur */
printf("%s: CBI bulk-in stall clear failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* no error recovery, otherwise we end up in a loop */
umass_clear_endpoint_stall(sc,
sc->bulkout, sc->bulkout_pipe, TSTATE_CBI_RESET3,
sc->transfer_xfer[XFER_CBI_RESET3]);
return;
case TSTATE_CBI_RESET3:
if (err) /* should not occur */
printf("%s: CBI bulk-out stall clear failed, %s\n",
USBDEVNAME(sc->sc_dev), usbd_errstr(err));
/* no error recovery, otherwise we end up in a loop */
sc->transfer_state = TSTATE_IDLE;
if (sc->transfer_priv) {
sc->transfer_cb(sc, sc->transfer_priv,
sc->transfer_datalen,
sc->transfer_status);
}
return;
/***** Default *****/
default:
panic("%s: Unknown state %d",
USBDEVNAME(sc->sc_dev), sc->transfer_state);
}
}
/*
* CAM specific functions (used by SCSI, UFI, 8070i (ATAPI))
*/
Static int
umass_cam_attach_sim(struct umass_softc *sc)
{
struct cam_devq *devq; /* Per device Queue */
/* A HBA is attached to the CAM layer.
*
* The CAM layer will then after a while start probing for
* devices on the bus. The number of SIMs is limited to one.
*/
devq = cam_simq_alloc(1 /*maximum openings*/);
if (devq == NULL)
return(ENOMEM);
sc->umass_sim = cam_sim_alloc(umass_cam_action, umass_cam_poll,
DEVNAME_SIM,
sc /*priv*/,
USBDEVUNIT(sc->sc_dev) /*unit number*/,
1 /*maximum device openings*/,
0 /*maximum tagged device openings*/,
devq);
if (sc->umass_sim == NULL) {
cam_simq_free(devq);
return(ENOMEM);
}
if(xpt_bus_register(sc->umass_sim, USBDEVUNIT(sc->sc_dev)) !=
CAM_SUCCESS)
return(ENOMEM);
return(0);
}
Static void
umass_cam_rescan_callback(struct cam_periph *periph, union ccb *ccb)
{
#ifdef USB_DEBUG
if (ccb->ccb_h.status != CAM_REQ_CMP) {
DPRINTF(UDMASS_SCSI, ("%s:%d Rescan failed, 0x%04x\n",
periph->periph_name, periph->unit_number,
ccb->ccb_h.status));
} else {
DPRINTF(UDMASS_SCSI, ("%s%d: Rescan succeeded\n",
periph->periph_name, periph->unit_number));
}
#endif
xpt_free_path(ccb->ccb_h.path);
free(ccb, M_USBDEV);
}
Static void
umass_cam_rescan(void *addr)
{
struct umass_softc *sc = (struct umass_softc *) addr;
struct cam_path *path;
union ccb *ccb = malloc(sizeof(union ccb), M_USBDEV, M_WAITOK);
memset(ccb, 0, sizeof(union ccb));
DPRINTF(UDMASS_SCSI, ("scbus%d: scanning for %s:%d:%d:%d\n",
cam_sim_path(sc->umass_sim),
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
USBDEVUNIT(sc->sc_dev), CAM_LUN_WILDCARD));
if (xpt_create_path(&path, xpt_periph, cam_sim_path(sc->umass_sim),
CAM_TARGET_WILDCARD, CAM_LUN_WILDCARD)
!= CAM_REQ_CMP)
return;
xpt_setup_ccb(&ccb->ccb_h, path, 5/*priority (low)*/);
ccb->ccb_h.func_code = XPT_SCAN_BUS;
ccb->ccb_h.cbfcnp = umass_cam_rescan_callback;
ccb->crcn.flags = CAM_FLAG_NONE;
xpt_action(ccb);
/* The scan is in progress now. */
}
Static int
umass_cam_attach(struct umass_softc *sc)
{
#ifndef USB_DEBUG
if (bootverbose)
#endif
printf("%s:%d:%d:%d: Attached to scbus%d\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
USBDEVUNIT(sc->sc_dev), CAM_LUN_WILDCARD,
cam_sim_path(sc->umass_sim));
if (!cold) {
/* Notify CAM of the new device after a short delay. Any
* failure is benign, as the user can still do it by hand
* (camcontrol rescan <busno>). Only do this if we are not
* booting, because CAM does a scan after booting has
* completed, when interrupts have been enabled.
*/
usb_callout(sc->cam_scsi_rescan_ch, MS_TO_TICKS(200),
umass_cam_rescan, sc);
}
return(0); /* always succesfull */
}
/* umass_cam_detach
* detach from the CAM layer
*/
Static int
umass_cam_detach_sim(struct umass_softc *sc)
{
if (sc->umass_sim) {
if (xpt_bus_deregister(cam_sim_path(sc->umass_sim)))
cam_sim_free(sc->umass_sim, /*free_devq*/TRUE);
else
return(EBUSY);
sc->umass_sim = NULL;
}
return(0);
}
/* umass_cam_action
* CAM requests for action come through here
*/
Static void
umass_cam_action(struct cam_sim *sim, union ccb *ccb)
{
struct umass_softc *sc = (struct umass_softc *)sim->softc;
/* The softc is still there, but marked as going away. umass_cam_detach
* has not yet notified CAM of the lost device however.
*/
if (sc && (sc->flags & UMASS_FLAGS_GONE)) {
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:func_code 0x%04x: "
"Invalid target (gone)\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
ccb->ccb_h.func_code));
ccb->ccb_h.status = CAM_TID_INVALID;
xpt_done(ccb);
return;
}
/* Verify, depending on the operation to perform, that we either got a
* valid sc, because an existing target was referenced, or otherwise
* the SIM is addressed.
*
* This avoids bombing out at a printf and does give the CAM layer some
* sensible feedback on errors.
*/
switch (ccb->ccb_h.func_code) {
case XPT_SCSI_IO:
case XPT_RESET_DEV:
case XPT_GET_TRAN_SETTINGS:
case XPT_SET_TRAN_SETTINGS:
case XPT_CALC_GEOMETRY:
/* the opcodes requiring a target. These should never occur. */
if (sc == NULL) {
printf("%s:%d:%d:%d:func_code 0x%04x: "
"Invalid target (target needed)\n",
DEVNAME_SIM, cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
ccb->ccb_h.func_code);
ccb->ccb_h.status = CAM_TID_INVALID;
xpt_done(ccb);
return;
}
break;
case XPT_PATH_INQ:
case XPT_NOOP:
/* The opcodes sometimes aimed at a target (sc is valid),
* sometimes aimed at the SIM (sc is invalid and target is
* CAM_TARGET_WILDCARD)
*/
if (sc == NULL && ccb->ccb_h.target_id != CAM_TARGET_WILDCARD) {
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:func_code 0x%04x: "
"Invalid target (no wildcard)\n",
DEVNAME_SIM, cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
ccb->ccb_h.func_code));
ccb->ccb_h.status = CAM_TID_INVALID;
xpt_done(ccb);
return;
}
break;
default:
/* XXX Hm, we should check the input parameters */
break;
}
/* Perform the requested action */
switch (ccb->ccb_h.func_code) {
case XPT_SCSI_IO:
{
struct ccb_scsiio *csio = &ccb->csio; /* deref union */
int dir;
unsigned char *cmd;
int cmdlen;
unsigned char *rcmd;
int rcmdlen;
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_SCSI_IO: "
"cmd: 0x%02x, flags: 0x%02x, "
"%db cmd/%db data/%db sense\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
csio->cdb_io.cdb_bytes[0],
ccb->ccb_h.flags & CAM_DIR_MASK,
csio->cdb_len, csio->dxfer_len,
csio->sense_len));
/* clear the end of the buffer to make sure we don't send out
* garbage.
*/
DIF(UDMASS_SCSI, if ((ccb->ccb_h.flags & CAM_DIR_MASK)
== CAM_DIR_OUT)
umass_dump_buffer(sc, csio->data_ptr,
csio->dxfer_len, 48));
if (sc->transfer_state != TSTATE_IDLE) {
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_SCSI_IO: "
"I/O in progress, deferring (state %d, %s)\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
sc->transfer_state,states[sc->transfer_state]));
ccb->ccb_h.status = CAM_SCSI_BUSY;
xpt_done(ccb);
return;
}
switch(ccb->ccb_h.flags&CAM_DIR_MASK) {
case CAM_DIR_IN:
dir = DIR_IN;
break;
case CAM_DIR_OUT:
dir = DIR_OUT;
break;
default:
dir = DIR_NONE;
}
ccb->ccb_h.status = CAM_REQ_INPROG | CAM_SIM_QUEUED;
if (csio->ccb_h.flags & CAM_CDB_POINTER) {
cmd = (unsigned char *) csio->cdb_io.cdb_ptr;
} else {
cmd = (unsigned char *) &csio->cdb_io.cdb_bytes;
}
cmdlen = csio->cdb_len;
rcmd = (unsigned char *) &sc->cam_scsi_command;
rcmdlen = sizeof(sc->cam_scsi_command);
/* sc->transform will convert the command to the command
* (format) needed by the specific command set and return
* the converted command in a buffer pointed to be rcmd.
* We pass in a buffer, but if the command does not
* have to be transformed it returns a ptr to the original
* buffer (see umass_scsi_transform).
*/
if (sc->transform(sc, cmd, cmdlen, &rcmd, &rcmdlen)) {
/*
* Handle EVPD inquiry for broken devices first
* NO_INQUIRY also implies NO_INQUIRY_EVPD
*/
if ((sc->quirks & (NO_INQUIRY_EVPD | NO_INQUIRY)) &&
rcmd[0] == INQUIRY && (rcmd[1] & SI_EVPD)) {
struct scsi_sense_data *sense;
sense = &ccb->csio.sense_data;
bzero(sense, sizeof(*sense));
sense->error_code = SSD_CURRENT_ERROR;
sense->flags = SSD_KEY_ILLEGAL_REQUEST;
sense->add_sense_code = 0x24;
sense->extra_len = 10;
ccb->csio.scsi_status = SCSI_STATUS_CHECK_COND;
ccb->ccb_h.status = CAM_SCSI_STATUS_ERROR |
CAM_AUTOSNS_VALID;
xpt_done(ccb);
return;
}
/* Return fake inquiry data for broken devices */
if ((sc->quirks & NO_INQUIRY) && rcmd[0] == INQUIRY) {
struct ccb_scsiio *csio = &ccb->csio;
memcpy(csio->data_ptr, &fake_inq_data,
sizeof(fake_inq_data));
csio->scsi_status = SCSI_STATUS_OK;
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
return;
}
if ((sc->quirks & FORCE_SHORT_INQUIRY) &&
rcmd[0] == INQUIRY) {
csio->dxfer_len = SHORT_INQUIRY_LENGTH;
}
sc->transfer(sc, ccb->ccb_h.target_lun, rcmd, rcmdlen,
csio->data_ptr,
csio->dxfer_len, dir, ccb->ccb_h.timeout,
umass_cam_cb, (void *) ccb);
} else {
ccb->ccb_h.status = CAM_REQ_INVALID;
xpt_done(ccb);
}
break;
}
case XPT_PATH_INQ:
{
struct ccb_pathinq *cpi = &ccb->cpi;
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_PATH_INQ:.\n",
(sc == NULL? DEVNAME_SIM:USBDEVNAME(sc->sc_dev)),
cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun));
/* host specific information */
cpi->version_num = 1;
cpi->hba_inquiry = 0;
cpi->target_sprt = 0;
cpi->hba_misc = PIM_NO_6_BYTE;
cpi->hba_eng_cnt = 0;
cpi->max_target = UMASS_SCSIID_MAX; /* one target */
cpi->initiator_id = UMASS_SCSIID_HOST;
strncpy(cpi->sim_vid, "FreeBSD", SIM_IDLEN);
strncpy(cpi->hba_vid, "USB SCSI", HBA_IDLEN);
strncpy(cpi->dev_name, cam_sim_name(sim), DEV_IDLEN);
cpi->unit_number = cam_sim_unit(sim);
cpi->bus_id = USBDEVUNIT(sc->sc_dev);
if (sc == NULL) {
cpi->base_transfer_speed = 0;
cpi->max_lun = 0;
} else {
if (sc->quirks & FLOPPY_SPEED) {
cpi->base_transfer_speed =
UMASS_FLOPPY_TRANSFER_SPEED;
} else if (usbd_get_speed(sc->sc_udev) ==
USB_SPEED_HIGH) {
cpi->base_transfer_speed =
UMASS_HIGH_TRANSFER_SPEED;
} else {
cpi->base_transfer_speed =
UMASS_FULL_TRANSFER_SPEED;
}
cpi->max_lun = sc->maxlun;
}
cpi->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
case XPT_RESET_DEV:
{
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_RESET_DEV:.\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun));
ccb->ccb_h.status = CAM_REQ_INPROG;
umass_reset(sc, umass_cam_cb, (void *) ccb);
break;
}
case XPT_GET_TRAN_SETTINGS:
{
struct ccb_trans_settings *cts = &ccb->cts;
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_GET_TRAN_SETTINGS:.\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun));
cts->valid = 0;
cts->flags = 0; /* no disconnection, tagging */
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
case XPT_SET_TRAN_SETTINGS:
{
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_SET_TRAN_SETTINGS:.\n",
USBDEVNAME(sc->sc_dev), cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun));
ccb->ccb_h.status = CAM_FUNC_NOTAVAIL;
xpt_done(ccb);
break;
}
case XPT_CALC_GEOMETRY:
{
cam_calc_geometry(&ccb->ccg, /*extended*/1);
xpt_done(ccb);
break;
}
case XPT_NOOP:
{
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:XPT_NOOP:.\n",
(sc == NULL? DEVNAME_SIM:USBDEVNAME(sc->sc_dev)),
cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun));
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
default:
DPRINTF(UDMASS_SCSI, ("%s:%d:%d:%d:func_code 0x%04x: "
"Not implemented\n",
(sc == NULL? DEVNAME_SIM:USBDEVNAME(sc->sc_dev)),
cam_sim_path(sc->umass_sim),
ccb->ccb_h.target_id, ccb->ccb_h.target_lun,
ccb->ccb_h.func_code));
ccb->ccb_h.status = CAM_FUNC_NOTAVAIL;
xpt_done(ccb);
break;
}
}
/* umass_cam_poll
* all requests are handled through umass_cam_action, requests
* are never pending. So, nothing to do here.
*/
Static void
umass_cam_poll(struct cam_sim *sim)
{
#ifdef USB_DEBUG
struct umass_softc *sc = (struct umass_softc *) sim->softc;
DPRINTF(UDMASS_SCSI, ("%s: CAM poll\n",
USBDEVNAME(sc->sc_dev)));
#endif
/* nop */
}
/* umass_cam_cb
* finalise a completed CAM command
*/
Static void
umass_cam_cb(struct umass_softc *sc, void *priv, int residue, int status)
{
union ccb *ccb = (union ccb *) priv;
struct ccb_scsiio *csio = &ccb->csio; /* deref union */
/* If the device is gone, just fail the request. */
if (sc->flags & UMASS_FLAGS_GONE) {
ccb->ccb_h.status = CAM_TID_INVALID;
xpt_done(ccb);
return;
}
csio->resid = residue;
switch (status) {
case STATUS_CMD_OK:
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
case STATUS_CMD_UNKNOWN:
case STATUS_CMD_FAILED:
switch (ccb->ccb_h.func_code) {
case XPT_SCSI_IO:
{
unsigned char *rcmd;
int rcmdlen;
/* fetch sense data */
/* the rest of the command was filled in at attach */
sc->cam_scsi_sense.length = csio->sense_len;
DPRINTF(UDMASS_SCSI,("%s: Fetching %db sense data\n",
USBDEVNAME(sc->sc_dev), csio->sense_len));
rcmd = (unsigned char *) &sc->cam_scsi_command;
rcmdlen = sizeof(sc->cam_scsi_command);
if (sc->transform(sc,
(unsigned char *) &sc->cam_scsi_sense,
sizeof(sc->cam_scsi_sense),
&rcmd, &rcmdlen)) {
if ((sc->quirks & FORCE_SHORT_INQUIRY) && (rcmd[0] == INQUIRY)) {
csio->sense_len = SHORT_INQUIRY_LENGTH;
}
sc->transfer(sc, ccb->ccb_h.target_lun,
rcmd, rcmdlen,
&csio->sense_data,
csio->sense_len, DIR_IN, ccb->ccb_h.timeout,
umass_cam_sense_cb, (void *) ccb);
} else {
panic("transform(REQUEST_SENSE) failed");
}
break;
}
case XPT_RESET_DEV: /* Reset failed */
ccb->ccb_h.status = CAM_REQ_CMP_ERR;
xpt_done(ccb);
break;
default:
panic("umass_cam_cb called for func_code %d",
ccb->ccb_h.func_code);
}
break;
case STATUS_WIRE_FAILED:
/* the wire protocol failed and will have recovered
* (hopefully). We return an error to CAM and let CAM retry
* the command if necessary.
*/
ccb->ccb_h.status = CAM_REQ_CMP_ERR;
xpt_done(ccb);
break;
default:
panic("%s: Unknown status %d in umass_cam_cb",
USBDEVNAME(sc->sc_dev), status);
}
}
/* Finalise a completed autosense operation
*/
Static void
umass_cam_sense_cb(struct umass_softc *sc, void *priv, int residue, int status)
{
union ccb *ccb = (union ccb *) priv;
struct ccb_scsiio *csio = &ccb->csio; /* deref union */
unsigned char *rcmd;
int rcmdlen;
if (sc->flags & UMASS_FLAGS_GONE) {
ccb->ccb_h.status = CAM_AUTOSENSE_FAIL;
xpt_done(ccb);
return;
}
switch (status) {
case STATUS_CMD_OK:
case STATUS_CMD_UNKNOWN:
case STATUS_CMD_FAILED:
/* Getting sense data always succeeds (apart from wire
* failures).
*/
if ((sc->quirks & RS_NO_CLEAR_UA)
&& csio->cdb_io.cdb_bytes[0] == INQUIRY
&& (csio->sense_data.flags & SSD_KEY)
== SSD_KEY_UNIT_ATTENTION) {
/* Ignore unit attention errors in the case where
* the Unit Attention state is not cleared on
* REQUEST SENSE. They will appear again at the next
* command.
*/
ccb->ccb_h.status = CAM_REQ_CMP;
} else if ((csio->sense_data.flags & SSD_KEY)
== SSD_KEY_NO_SENSE) {
/* No problem after all (in the case of CBI without
* CCI)
*/
ccb->ccb_h.status = CAM_REQ_CMP;
} else if ((sc->quirks & RS_NO_CLEAR_UA) &&
(csio->cdb_io.cdb_bytes[0] == READ_CAPACITY) &&
((csio->sense_data.flags & SSD_KEY)
== SSD_KEY_UNIT_ATTENTION)) {
/*
* Some devices do not clear the unit attention error
* on request sense. We insert a test unit ready
* command to make sure we clear the unit attention
* condition, then allow the retry to proceed as
* usual.
*/
ccb->ccb_h.status = CAM_SCSI_STATUS_ERROR
| CAM_AUTOSNS_VALID;
csio->scsi_status = SCSI_STATUS_CHECK_COND;
#if 0
DELAY(300000);
#endif
DPRINTF(UDMASS_SCSI,("%s: Doing a sneaky"
"TEST_UNIT_READY\n",
USBDEVNAME(sc->sc_dev)));
/* the rest of the command was filled in at attach */
rcmd = (unsigned char *) &sc->cam_scsi_command2;
rcmdlen = sizeof(sc->cam_scsi_command2);
if (sc->transform(sc,
(unsigned char *)
&sc->cam_scsi_test_unit_ready,
sizeof(sc->cam_scsi_test_unit_ready),
&rcmd, &rcmdlen)) {
sc->transfer(sc, ccb->ccb_h.target_lun,
rcmd, rcmdlen,
NULL, 0, DIR_NONE, ccb->ccb_h.timeout,
umass_cam_quirk_cb, (void *) ccb);
} else {
panic("transform(TEST_UNIT_READY) failed");
}
break;
} else {
ccb->ccb_h.status = CAM_SCSI_STATUS_ERROR
| CAM_AUTOSNS_VALID;
csio->scsi_status = SCSI_STATUS_CHECK_COND;
}
xpt_done(ccb);
break;
default:
DPRINTF(UDMASS_SCSI, ("%s: Autosense failed, status %d\n",
USBDEVNAME(sc->sc_dev), status));
ccb->ccb_h.status = CAM_AUTOSENSE_FAIL;
xpt_done(ccb);
}
}
/*
* This completion code just handles the fact that we sent a test-unit-ready
* after having previously failed a READ CAPACITY with CHECK_COND. Even
* though this command succeeded, we have to tell CAM to retry.
*/
Static void
umass_cam_quirk_cb(struct umass_softc *sc, void *priv, int residue, int status)
{
union ccb *ccb = (union ccb *) priv;
DPRINTF(UDMASS_SCSI, ("%s: Test unit ready returned status %d\n",
USBDEVNAME(sc->sc_dev), status));
if (sc->flags & UMASS_FLAGS_GONE) {
ccb->ccb_h.status = CAM_TID_INVALID;
xpt_done(ccb);
return;
}
#if 0
ccb->ccb_h.status = CAM_REQ_CMP;
#endif
ccb->ccb_h.status = CAM_SCSI_STATUS_ERROR
| CAM_AUTOSNS_VALID;
ccb->csio.scsi_status = SCSI_STATUS_CHECK_COND;
xpt_done(ccb);
}
Static int
umass_driver_load(module_t mod, int what, void *arg)
{
switch (what) {
case MOD_UNLOAD:
case MOD_LOAD:
default:
return(usbd_driver_load(mod, what, arg));
}
}
/*
* SCSI specific functions
*/
Static int
umass_scsi_transform(struct umass_softc *sc, unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen)
{
switch (cmd[0]) {
case TEST_UNIT_READY:
if (sc->quirks & NO_TEST_UNIT_READY) {
KASSERT(*rcmdlen >= sizeof(struct scsi_start_stop_unit),
("rcmdlen = %d < %ld, buffer too small",
*rcmdlen,
(long)sizeof(struct scsi_start_stop_unit)));
DPRINTF(UDMASS_SCSI, ("%s: Converted TEST_UNIT_READY "
"to START_UNIT\n", USBDEVNAME(sc->sc_dev)));
memset(*rcmd, 0, *rcmdlen);
(*rcmd)[0] = START_STOP_UNIT;
(*rcmd)[4] = SSS_START;
return 1;
}
/* fallthrough */
case INQUIRY:
/* some drives wedge when asked for full inquiry information. */
if (sc->quirks & FORCE_SHORT_INQUIRY) {
memcpy(*rcmd, cmd, cmdlen);
*rcmdlen = cmdlen;
(*rcmd)[4] = SHORT_INQUIRY_LENGTH;
return 1;
}
/* fallthrough */
default:
*rcmd = cmd; /* We don't need to copy it */
*rcmdlen = cmdlen;
}
return 1;
}
/* RBC specific functions */
Static int
umass_rbc_transform(struct umass_softc *sc, unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen)
{
switch (cmd[0]) {
/* these commands are defined in RBC: */
case READ_10:
case READ_CAPACITY:
case START_STOP_UNIT:
case SYNCHRONIZE_CACHE:
case WRITE_10:
case 0x2f: /* VERIFY_10 is absent from scsi_all.h??? */
case INQUIRY:
case MODE_SELECT_10:
case MODE_SENSE_10:
case TEST_UNIT_READY:
case WRITE_BUFFER:
/* The following commands are not listed in my copy of the RBC specs.
* CAM however seems to want those, and at least the Sony DSC device
* appears to support those as well */
case REQUEST_SENSE:
case PREVENT_ALLOW:
*rcmd = cmd; /* We don't need to copy it */
*rcmdlen = cmdlen;
return 1;
/* All other commands are not legal in RBC */
default:
printf("%s: Unsupported RBC command 0x%02x",
USBDEVNAME(sc->sc_dev), cmd[0]);
printf("\n");
return 0; /* failure */
}
}
/*
* UFI specific functions
*/
Static int
umass_ufi_transform(struct umass_softc *sc, unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen)
{
/* A UFI command is always 12 bytes in length */
KASSERT(*rcmdlen >= UFI_COMMAND_LENGTH,
("rcmdlen = %d < %d, buffer too small",
*rcmdlen, UFI_COMMAND_LENGTH));
*rcmdlen = UFI_COMMAND_LENGTH;
memset(*rcmd, 0, UFI_COMMAND_LENGTH);
switch (cmd[0]) {
/* Commands of which the format has been verified. They should work.
* Copy the command into the (zeroed out) destination buffer.
*/
case TEST_UNIT_READY:
if (sc->quirks & NO_TEST_UNIT_READY) {
/* Some devices do not support this command.
* Start Stop Unit should give the same results
*/
DPRINTF(UDMASS_UFI, ("%s: Converted TEST_UNIT_READY "
"to START_UNIT\n", USBDEVNAME(sc->sc_dev)));
(*rcmd)[0] = START_STOP_UNIT;
(*rcmd)[4] = SSS_START;
} else {
memcpy(*rcmd, cmd, cmdlen);
}
return 1;
case REZERO_UNIT:
case REQUEST_SENSE:
case FORMAT_UNIT:
case INQUIRY:
case START_STOP_UNIT:
case SEND_DIAGNOSTIC:
case PREVENT_ALLOW:
case READ_CAPACITY:
case READ_10:
case WRITE_10:
case POSITION_TO_ELEMENT: /* SEEK_10 */
case WRITE_AND_VERIFY:
case VERIFY:
case MODE_SELECT_10:
case MODE_SENSE_10:
case READ_12:
case WRITE_12:
case READ_FORMAT_CAPACITIES:
memcpy(*rcmd, cmd, cmdlen);
return 1;
default:
printf("%s: Unsupported UFI command 0x%02x\n",
USBDEVNAME(sc->sc_dev), cmd[0]);
return 0; /* failure */
}
}
/*
* 8070i (ATAPI) specific functions
*/
Static int
umass_atapi_transform(struct umass_softc *sc, unsigned char *cmd, int cmdlen,
unsigned char **rcmd, int *rcmdlen)
{
/* An ATAPI command is always 12 bytes in length. */
KASSERT(*rcmdlen >= ATAPI_COMMAND_LENGTH,
("rcmdlen = %d < %d, buffer too small",
*rcmdlen, ATAPI_COMMAND_LENGTH));
*rcmdlen = ATAPI_COMMAND_LENGTH;
memset(*rcmd, 0, ATAPI_COMMAND_LENGTH);
switch (cmd[0]) {
/* Commands of which the format has been verified. They should work.
* Copy the command into the (zeroed out) destination buffer.
*/
case INQUIRY:
memcpy(*rcmd, cmd, cmdlen);
/* some drives wedge when asked for full inquiry information. */
if (sc->quirks & FORCE_SHORT_INQUIRY)
(*rcmd)[4] = SHORT_INQUIRY_LENGTH;
return 1;
case TEST_UNIT_READY:
if (sc->quirks & NO_TEST_UNIT_READY) {
KASSERT(*rcmdlen >= sizeof(struct scsi_start_stop_unit),
("rcmdlen = %d < %ld, buffer too small",
*rcmdlen,
(long)sizeof(struct scsi_start_stop_unit)));
DPRINTF(UDMASS_SCSI, ("%s: Converted TEST_UNIT_READY "
"to START_UNIT\n", USBDEVNAME(sc->sc_dev)));
memset(*rcmd, 0, *rcmdlen);
(*rcmd)[0] = START_STOP_UNIT;
(*rcmd)[4] = SSS_START;
return 1;
}
/* fallthrough */
case REZERO_UNIT:
case REQUEST_SENSE:
case START_STOP_UNIT:
case SEND_DIAGNOSTIC:
case PREVENT_ALLOW:
case READ_CAPACITY:
case READ_10:
case WRITE_10:
case POSITION_TO_ELEMENT: /* SEEK_10 */
case SYNCHRONIZE_CACHE:
case MODE_SELECT_10:
case MODE_SENSE_10:
case READ_BUFFER:
case 0x42: /* READ_SUBCHANNEL */
case 0x43: /* READ_TOC */
case 0x44: /* READ_HEADER */
case 0x51: /* READ_DISK_INFO */
case 0x52: /* READ_TRACK_INFO */
case 0x54: /* SEND_OPC */
case 0x59: /* READ_MASTER_CUE */
case 0x5b: /* CLOSE_TR_SESSION */
case 0x5c: /* READ_BUFFER_CAP */
case 0x5d: /* SEND_CUE_SHEET */
case 0xa1: /* BLANK */
case 0xa6: /* EXCHANGE_MEDIUM */
case 0xad: /* READ_DVD_STRUCTURE */
case 0xbb: /* SET_CD_SPEED */
case 0xe5: /* READ_TRACK_INFO_PHILIPS */
memcpy(*rcmd, cmd, cmdlen);
return 1;
case READ_12:
case WRITE_12:
default:
printf("%s: Unsupported ATAPI command 0x%02x\n",
USBDEVNAME(sc->sc_dev), cmd[0]);
return 0; /* failure */
}
}
/* (even the comment is missing) */
DRIVER_MODULE(umass, uhub, umass_driver, umass_devclass, umass_driver_load, 0);
#ifdef USB_DEBUG
Static void
umass_bbb_dump_cbw(struct umass_softc *sc, umass_bbb_cbw_t *cbw)
{
int clen = cbw->bCDBLength;
int dlen = UGETDW(cbw->dCBWDataTransferLength);
u_int8_t *c = cbw->CBWCDB;
int tag = UGETDW(cbw->dCBWTag);
int flags = cbw->bCBWFlags;
DPRINTF(UDMASS_BBB, ("%s: CBW %d: cmd = %db "
"(0x%02x%02x%02x%02x%02x%02x%s), "
"data = %db, dir = %s\n",
USBDEVNAME(sc->sc_dev), tag, clen,
c[0], c[1], c[2], c[3], c[4], c[5], (clen > 6? "...":""),
dlen, (flags == CBWFLAGS_IN? "in":
(flags == CBWFLAGS_OUT? "out":"<invalid>"))));
}
Static void
umass_bbb_dump_csw(struct umass_softc *sc, umass_bbb_csw_t *csw)
{
int sig = UGETDW(csw->dCSWSignature);
int tag = UGETW(csw->dCSWTag);
int res = UGETDW(csw->dCSWDataResidue);
int status = csw->bCSWStatus;
DPRINTF(UDMASS_BBB, ("%s: CSW %d: sig = 0x%08x (%s), tag = %d, "
"res = %d, status = 0x%02x (%s)\n", USBDEVNAME(sc->sc_dev),
tag, sig, (sig == CSWSIGNATURE? "valid":"invalid"),
tag, res,
status, (status == CSWSTATUS_GOOD? "good":
(status == CSWSTATUS_FAILED? "failed":
(status == CSWSTATUS_PHASE? "phase":"<invalid>")))));
}
Static void
umass_cbi_dump_cmd(struct umass_softc *sc, void *cmd, int cmdlen)
{
u_int8_t *c = cmd;
int dir = sc->transfer_dir;
DPRINTF(UDMASS_BBB, ("%s: cmd = %db "
"(0x%02x%02x%02x%02x%02x%02x%s), "
"data = %db, dir = %s\n",
USBDEVNAME(sc->sc_dev), cmdlen,
c[0], c[1], c[2], c[3], c[4], c[5], (cmdlen > 6? "...":""),
sc->transfer_datalen,
(dir == DIR_IN? "in":
(dir == DIR_OUT? "out":
(dir == DIR_NONE? "no data phase": "<invalid>")))));
}
Static void
umass_dump_buffer(struct umass_softc *sc, u_int8_t *buffer, int buflen,
int printlen)
{
int i, j;
char s1[40];
char s2[40];
char s3[5];
s1[0] = '\0';
s3[0] = '\0';
sprintf(s2, " buffer=%p, buflen=%d", buffer, buflen);
for (i = 0; i < buflen && i < printlen; i++) {
j = i % 16;
if (j == 0 && i != 0) {
DPRINTF(UDMASS_GEN, ("%s: 0x %s%s\n",
USBDEVNAME(sc->sc_dev), s1, s2));
s2[0] = '\0';
}
sprintf(&s1[j*2], "%02x", buffer[i] & 0xff);
}
if (buflen > printlen)
sprintf(s3, " ...");
DPRINTF(UDMASS_GEN, ("%s: 0x %s%s%s\n",
USBDEVNAME(sc->sc_dev), s1, s2, s3));
}
#endif
Reference in New Issue View Git Blame Copy Permalink