ef27340c5b
for the ath(4) driver. Currently, there's nothing stopping reset, channel change and general TX/RX from overlapping with each other. This wasn't a big deal with pre-11n traffic as it just results in some dropped frames. It's possible this may have also caused some inconsistencies and badly-setup hardware. Since locks can't be held across all of this (the Linux solution) due to LORs with the network stack locks, some state counter variables are used to track what parts of the code the driver is currently in. When the hardware is being reset, it disables the taskqueue and waits for pending interrupts, tx, rx and tx completion before it begins the reset or channel change. TX and RX both abort if called during an active reset or channel change. Finally, the reset path now doesn't flush frames if ATH_RESET_NOLOSS is set. Instead, completed TX and RX frames are passed back up to net80211 before the reset occurs. This is not without problems: * Raw frame xmit are just dropped, rather than placed on a queue. The net80211 stack should be the one which queues these frames rather than the driver. * It's all very messy. It'd be better if these hardware operations were serialised on some kind of work queue, rather than hoping they can be run in parallel. * The taskqueue block/unblock may occur in parallel with the newstate() function - which shuts down the taskqueue and restarts it once the new state is known. It's likely these operations should be refcounted so the taskqueue is restored once no other areas in the code wish to suspend operations. * .. interrupt disable/enable should likely be refcounted as well. With this work, the driver does not drop frames during stuck beacon or fatal errors and thus 11n traffic continues to run correctly. Default and full resets however do still drop frames and it's possible this may occur, causing traffic loss and session stalls. Sponsored by: Hobnob, Inc.
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html