792c00971a
man page. Tweak comments to not refer to EISA scenarios now that it is no longer supported. Remove unused enum.
693 lines
18 KiB
C
693 lines
18 KiB
C
/*-
|
|
* Generic register and struct definitions for the BusLogic
|
|
* MultiMaster SCSI host adapters. Product specific probe and
|
|
* attach routines can be found in:
|
|
* sys/dev/buslogic/bt_isa.c BT-54X, BT-445 cards
|
|
* sys/dev/buslogic/bt_mca.c BT-64X, SDC3211B, SDC3211F
|
|
* sys/dev/buslogic/bt_pci.c BT-946, BT-948, BT-956, BT-958 cards
|
|
*
|
|
* Copyright (c) 1998, 1999 Justin T. Gibbs.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions, and the following disclaimer,
|
|
* without modification, immediately at the beginning of the file.
|
|
* 2. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
#ifndef _BTREG_H_
|
|
#define _BTREG_H_
|
|
|
|
#include <sys/queue.h>
|
|
|
|
#define BT_MAXTRANSFER_SIZE 0xffffffff /* limited by 32bit counter */
|
|
#define BT_NSEG 32 /* The number of dma segments supported.
|
|
* BT_NSEG can be maxed out at 8192 entries,
|
|
* but the kernel will never need to transfer
|
|
* such a large request. To reduce the
|
|
* driver's memory consumption, we reduce the
|
|
* max to 32. 16 would work if all transfers
|
|
* are paged alined since the kernel will only
|
|
* generate at most a 64k transfer, but to
|
|
* handle non-page aligned transfers, you need
|
|
* 17, so we round to the next power of two
|
|
* to make allocating SG space easy and
|
|
* efficient.
|
|
*/
|
|
|
|
#define ALL_TARGETS (~0)
|
|
|
|
/*
|
|
* Control Register pp. 1-8, 1-9 (Write Only)
|
|
*/
|
|
#define CONTROL_REG 0x00
|
|
#define HARD_RESET 0x80 /* Hard Reset - return to POST state */
|
|
#define SOFT_RESET 0x40 /* Soft Reset - Clears Adapter state */
|
|
#define RESET_INTR 0x20 /* Reset/Ack Interrupt */
|
|
#define RESET_SBUS 0x10 /* Drive SCSI bus reset signal */
|
|
|
|
/*
|
|
* Status Register pp. 1-9, 1-10 (Read Only)
|
|
*/
|
|
#define STATUS_REG 0x00
|
|
#define DIAG_ACTIVE 0x80 /* Performing Internal Diags */
|
|
#define DIAG_FAIL 0x40 /* Internal Diags failed */
|
|
#define INIT_REQUIRED 0x20 /* MBOXes need initialization */
|
|
#define HA_READY 0x10 /* HA ready for new commands */
|
|
#define CMD_REG_BUSY 0x08 /* HA busy with last cmd byte */
|
|
#define DATAIN_REG_READY 0x04 /* Data-in Byte available */
|
|
#define STATUS_REG_RSVD 0x02
|
|
#define CMD_INVALID 0x01 /* Invalid Command detected */
|
|
|
|
/*
|
|
* Command/Parameter Register pp. 1-10, 1-11 (Write Only)
|
|
*/
|
|
#define COMMAND_REG 0x01
|
|
|
|
/*
|
|
* Data in Register p. 1-11 (Read Only)
|
|
*/
|
|
#define DATAIN_REG 0x01
|
|
|
|
/*
|
|
* Interrupt Status Register pp. 1-12 -> 1-14 (Read Only)
|
|
*/
|
|
#define INTSTAT_REG 0x02
|
|
#define INTR_PENDING 0x80 /* There is a pending INTR */
|
|
#define INTSTAT_REG_RSVD 0x70
|
|
#define SCSI_BUS_RESET 0x08 /* Bus Reset detected */
|
|
#define CMD_COMPLETE 0x04
|
|
#define OMB_READY 0x02 /* Outgoin Mailbox Ready */
|
|
#define IMB_LOADED 0x01 /* Incoming Mailbox loaded */
|
|
|
|
/*
|
|
* Definitions for the "undocumented" geometry register
|
|
*/
|
|
typedef enum {
|
|
GEOM_NODISK,
|
|
GEOM_64x32,
|
|
GEOM_128x32,
|
|
GEOM_255x32
|
|
} disk_geom_t;
|
|
|
|
#define GEOMETRY_REG 0x03
|
|
#define DISK0_GEOMETRY 0x03
|
|
#define DISK1_GEOMETRY 0x0c
|
|
#define EXTENDED_TRANSLATION 0x80
|
|
#define GEOMETRY_DISK0(g_reg) (greg & DISK0_GEOMETRY)
|
|
#define GEOMETRY_DISK1(g_reg) ((greg & DISK1_GEOMETRY) >> 2)
|
|
|
|
#define BT_NREGS (4)
|
|
/*
|
|
* Opcodes for Adapter commands.
|
|
* pp 1-18 -> 1-20
|
|
*/
|
|
typedef enum {
|
|
BOP_TEST_CMDC_INTR = 0x00,
|
|
BOP_INITIALIZE_24BMBOX = 0x01,
|
|
BOP_START_MBOX = 0x02,
|
|
BOP_EXECUTE_BIOS_CMD = 0x03,
|
|
BOP_INQUIRE_BOARD_ID = 0x04,
|
|
BOP_ENABLE_OMBR_INT = 0x05,
|
|
BOP_SET_SEL_TIMOUT = 0x06,
|
|
BOP_SET_TIME_ON_BUS = 0x07,
|
|
BOP_SET_TIME_OFF_BUS = 0x08,
|
|
BOP_SET_BUS_TRANS_RATE = 0x09,
|
|
BOP_INQUIRE_INST_LDEVS = 0x0A,
|
|
BOP_INQUIRE_CONFIG = 0x0B,
|
|
BOP_ENABLE_TARGET_MODE = 0x0C,
|
|
BOP_INQUIRE_SETUP_INFO = 0x0D,
|
|
BOP_WRITE_LRAM = 0x1A,
|
|
BOP_READ_LRAM = 0x1B,
|
|
BOP_WRITE_CHIP_FIFO = 0x1C,
|
|
BOP_READ_CHIP_FIFO = 0x1C,
|
|
BOP_ECHO_DATA_BYTE = 0x1F,
|
|
BOP_ADAPTER_DIAGNOSTICS = 0x20,
|
|
BOP_SET_ADAPTER_OPTIONS = 0x21,
|
|
BOP_INQUIRE_INST_HDEVS = 0x23,
|
|
BOP_INQUIRE_TARG_DEVS = 0x24,
|
|
BOP_DISABLE_HAC_INTR = 0x25,
|
|
BOP_INITIALIZE_32BMBOX = 0x81,
|
|
BOP_EXECUTE_SCSI_CMD = 0x83,
|
|
BOP_INQUIRE_FW_VER_3DIG = 0x84,
|
|
BOP_INQUIRE_FW_VER_4DIG = 0x85,
|
|
BOP_INQUIRE_PCI_INFO = 0x86,
|
|
BOP_INQUIRE_MODEL = 0x8B,
|
|
BOP_TARG_SYNC_INFO = 0x8C,
|
|
BOP_INQUIRE_ESETUP_INFO = 0x8D,
|
|
BOP_ENABLE_STRICT_RR = 0x8F,
|
|
BOP_STORE_LRAM = 0x90,
|
|
BOP_FETCH_LRAM = 0x91,
|
|
BOP_SAVE_TO_EEPROM = 0x92,
|
|
BOP_UPLOAD_AUTO_SCSI = 0x94,
|
|
BOP_MODIFY_IO_ADDR = 0x95,
|
|
BOP_SET_CCB_FORMAT = 0x96,
|
|
BOP_FLASH_ROM_DOWNLOAD = 0x97,
|
|
BOP_FLASH_WRITE_ENABLE = 0x98,
|
|
BOP_WRITE_INQ_BUFFER = 0x9A,
|
|
BOP_READ_INQ_BUFFER = 0x9B,
|
|
BOP_FLASH_UP_DOWNLOAD = 0xA7,
|
|
BOP_READ_SCAM_DATA = 0xA8,
|
|
BOP_WRITE_SCAM_DATA = 0xA9
|
|
} bt_op_t;
|
|
|
|
/************** Definitions of Multi-byte commands and responses ************/
|
|
|
|
typedef struct {
|
|
u_int8_t num_mboxes;
|
|
u_int8_t base_addr[3];
|
|
} init_24b_mbox_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t board_type;
|
|
#define BOARD_TYPE_NON_MCA 0x41
|
|
#define BOARD_TYPE_MCA 0x42
|
|
u_int8_t cust_features;
|
|
#define FEATURES_STANDARD 0x41
|
|
u_int8_t firmware_rev_major;
|
|
u_int8_t firmware_rev_minor;
|
|
} board_id_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t enable;
|
|
} enable_ombr_intr_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t enable;
|
|
u_int8_t reserved;
|
|
u_int8_t timeout[2]; /* timeout in milliseconds */
|
|
} set_selto_parmas_t;
|
|
|
|
typedef struct {
|
|
u_int8_t time; /* time in milliseconds (2-15) */
|
|
} set_timeon_bus_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t time; /* time in milliseconds (2-15) */
|
|
} set_timeoff_bus_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t rate;
|
|
} set_bus_trasfer_rate_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t targets[8];
|
|
} installed_ldevs_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t dma_chan;
|
|
#define DMA_CHAN_5 0x20
|
|
#define DMA_CHAN_6 0x40
|
|
#define DMA_CHAN_7 0x80
|
|
u_int8_t irq;
|
|
#define IRQ_9 0x01
|
|
#define IRQ_10 0x02
|
|
#define IRQ_11 0x04
|
|
#define IRQ_12 0x08
|
|
#define IRQ_14 0x20
|
|
#define IRQ_15 0x40
|
|
u_int8_t scsi_id;
|
|
} config_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t enable;
|
|
} target_mode_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t offset : 4,
|
|
period : 3,
|
|
sync : 1;
|
|
} targ_syncinfo_t;
|
|
|
|
typedef struct {
|
|
u_int8_t initiate_sync : 1,
|
|
parity_enable : 1,
|
|
: 6;
|
|
|
|
u_int8_t bus_transfer_rate;
|
|
u_int8_t time_on_bus;
|
|
u_int8_t time_off_bus;
|
|
u_int8_t num_mboxes;
|
|
u_int8_t mbox_base_addr[3];
|
|
targ_syncinfo_t low_syncinfo[8]; /* For fast and ultra, use 8C */
|
|
u_int8_t low_discinfo;
|
|
u_int8_t customer_sig;
|
|
u_int8_t letter_d;
|
|
u_int8_t ha_type;
|
|
u_int8_t low_wide_allowed;
|
|
u_int8_t low_wide_active;
|
|
targ_syncinfo_t high_syncinfo[8];
|
|
u_int8_t high_discinfo;
|
|
u_int8_t high_wide_allowed;
|
|
u_int8_t high_wide_active;
|
|
} setup_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t phys_addr[3];
|
|
} write_adapter_lram_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t phys_addr[3];
|
|
} read_adapter_lram_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t phys_addr[3];
|
|
} write_chip_fifo_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t phys_addr[3];
|
|
} read_chip_fifo_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t length; /* Excludes this member */
|
|
u_int8_t low_disc_disable;
|
|
u_int8_t low_busy_retry_disable;
|
|
u_int8_t high_disc_disable;
|
|
u_int8_t high_busy_retry_disable;
|
|
} set_adapter_options_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t targets[8];
|
|
} installed_hdevs_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t low_devs;
|
|
u_int8_t high_devs;
|
|
} target_devs_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t enable;
|
|
} enable_hac_interrupt_params_t;
|
|
|
|
typedef struct {
|
|
u_int8_t num_boxes;
|
|
u_int8_t base_addr[4];
|
|
} init_32b_mbox_params_t;
|
|
|
|
typedef u_int8_t fw_ver_3dig_data_t;
|
|
|
|
typedef u_int8_t fw_ver_4dig_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t offset;
|
|
u_int8_t response_len;
|
|
} fetch_lram_params_t;
|
|
|
|
#define AUTO_SCSI_BYTE_OFFSET 64
|
|
typedef struct {
|
|
u_int8_t factory_sig[2];
|
|
u_int8_t auto_scsi_data_size; /* 2 -> 64 bytes */
|
|
u_int8_t model_num[6];
|
|
u_int8_t adapter_ioport;
|
|
u_int8_t floppy_enabled :1,
|
|
floppy_secondary :1,
|
|
level_trigger :1,
|
|
:2,
|
|
system_ram_area :3;
|
|
u_int8_t dma_channel :7,
|
|
dma_autoconf :1;
|
|
u_int8_t irq_channel :7,
|
|
irq_autoconf :1;
|
|
u_int8_t dma_trans_rate;
|
|
u_int8_t scsi_id;
|
|
u_int8_t low_termination :1,
|
|
scsi_parity :1,
|
|
high_termination :1,
|
|
req_ack_filter :1,
|
|
fast_sync :1,
|
|
bus_reset :1,
|
|
:1,
|
|
active_negation :1;
|
|
u_int8_t bus_on_delay;
|
|
u_int8_t bus_off_delay;
|
|
u_int8_t bios_enabled :1,
|
|
int19h_redirect :1,
|
|
extended_trans :1,
|
|
removable_drives :1,
|
|
:1,
|
|
morethan2disks :1,
|
|
interrupt_mode :1,
|
|
floptical_support:1;
|
|
u_int8_t low_device_enabled;
|
|
u_int8_t high_device_enabled;
|
|
u_int8_t low_wide_permitted;
|
|
u_int8_t high_wide_permitted;
|
|
u_int8_t low_fast_permitted;
|
|
u_int8_t high_fast_permitted;
|
|
u_int8_t low_sync_permitted;
|
|
u_int8_t high_sync_permitted;
|
|
u_int8_t low_disc_permitted;
|
|
u_int8_t high_disc_permitted;
|
|
u_int8_t low_send_start_unit;
|
|
u_int8_t high_send_start_unit;
|
|
u_int8_t low_ignore_in_bios_scan;
|
|
u_int8_t high_ignore_in_bios_scan;
|
|
u_int8_t pci_int_pin :2,
|
|
host_ioport :2,
|
|
round_robin :1,
|
|
vesa_bus_over_33 :1,
|
|
vesa_burst_write :1,
|
|
vesa_burst_read :1;
|
|
u_int8_t low_ultra_permitted;
|
|
u_int8_t high_ultra_permitted;
|
|
u_int8_t reserved[5];
|
|
u_int8_t auto_scsi_max_lun;
|
|
u_int8_t :1,
|
|
scam_dominant :1,
|
|
scam_enabled :1,
|
|
scam_level2 :1,
|
|
:4;
|
|
u_int8_t int13_extensions :1,
|
|
:1,
|
|
cdrom_boot :1,
|
|
:2,
|
|
multi_boot :1,
|
|
:2;
|
|
u_int8_t boot_target_id :4,
|
|
boot_channel :4;
|
|
u_int8_t force_dev_scan :1,
|
|
:7;
|
|
u_int8_t low_tagged_lun_independance;
|
|
u_int8_t high_tagged_lun_independance;
|
|
u_int8_t low_renegotiate_after_cc;
|
|
u_int8_t high_renegotiate_after_cc;
|
|
u_int8_t reserverd2[10];
|
|
u_int8_t manufacturing_diagnotic[2];
|
|
u_int8_t checksum[2];
|
|
} auto_scsi_data_t;
|
|
|
|
struct bt_isa_port {
|
|
u_int16_t addr;
|
|
u_int8_t probed;
|
|
u_int8_t bio;
|
|
};
|
|
|
|
extern struct bt_isa_port bt_isa_ports[];
|
|
|
|
#define BT_NUM_ISAPORTS 6
|
|
|
|
typedef enum {
|
|
BIO_330 = 0,
|
|
BIO_334 = 1,
|
|
BIO_230 = 2,
|
|
BIO_234 = 3,
|
|
BIO_130 = 4,
|
|
BIO_134 = 5,
|
|
BIO_DISABLED = 6,
|
|
BIO_DISABLED2 = 7
|
|
} isa_compat_io_t;
|
|
|
|
typedef struct {
|
|
u_int8_t io_port;
|
|
u_int8_t irq_num;
|
|
u_int8_t low_byte_term :1,
|
|
high_byte_term :1,
|
|
:2,
|
|
jp1_status :1,
|
|
jp2_status :1,
|
|
jp3_status :1,
|
|
:1;
|
|
u_int8_t reserved;
|
|
} pci_info_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t ascii_model[5]; /* Fifth byte is always 0 */
|
|
} ha_model_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t sync_rate[16]; /* Sync in 10ns units */
|
|
} target_sync_info_data_t;
|
|
|
|
typedef struct {
|
|
u_int8_t bus_type;
|
|
u_int8_t bios_addr;
|
|
u_int16_t max_sg;
|
|
u_int8_t num_mboxes;
|
|
u_int8_t mbox_base[4];
|
|
u_int8_t :2,
|
|
sync_neg10MB :1,
|
|
floppy_disable :1,
|
|
floppy_secondary_port :1,
|
|
burst_mode_enabled :1,
|
|
level_trigger_ints :1,
|
|
:1;
|
|
u_int8_t fw_ver_bytes_2_to_4[3];
|
|
u_int8_t wide_bus :1,
|
|
diff_bus :1,
|
|
scam_capable :1,
|
|
ultra_scsi :1,
|
|
auto_term :1,
|
|
:3;
|
|
} esetup_info_data_t;
|
|
|
|
typedef struct {
|
|
u_int32_t len;
|
|
u_int32_t addr;
|
|
} bt_sg_t;
|
|
|
|
/********************** Mail Box definitions *******************************/
|
|
|
|
typedef enum {
|
|
BMBO_FREE = 0x0, /* MBO intry is free */
|
|
BMBO_START = 0x1, /* MBO activate entry */
|
|
BMBO_ABORT = 0x2 /* MBO abort entry */
|
|
} bt_mbo_action_code_t;
|
|
|
|
typedef struct bt_mbox_out {
|
|
u_int32_t ccb_addr;
|
|
u_int8_t reserved[3];
|
|
u_int8_t action_code;
|
|
} bt_mbox_out_t;
|
|
|
|
typedef enum {
|
|
BMBI_FREE = 0x0, /* MBI entry is free */
|
|
BMBI_OK = 0x1, /* completed without error */
|
|
BMBI_ABORT = 0x2, /* aborted ccb */
|
|
BMBI_NOT_FOUND = 0x3, /* Tried to abort invalid CCB */
|
|
BMBI_ERROR = 0x4 /* Completed with error */
|
|
} bt_mbi_comp_code_t;
|
|
|
|
typedef struct bt_mbox_in {
|
|
u_int32_t ccb_addr;
|
|
u_int8_t btstat;
|
|
u_int8_t sdstat;
|
|
u_int8_t reserved;
|
|
u_int8_t comp_code;
|
|
} bt_mbox_in_t;
|
|
|
|
/***************** Compiled Probe Information *******************************/
|
|
struct bt_probe_info {
|
|
int drq;
|
|
int irq;
|
|
};
|
|
|
|
/****************** Hardware CCB definition *********************************/
|
|
typedef enum {
|
|
INITIATOR_CCB = 0x00,
|
|
INITIATOR_SG_CCB = 0x02,
|
|
INITIATOR_CCB_WRESID = 0x03,
|
|
INITIATOR_SG_CCB_WRESID = 0x04,
|
|
INITIATOR_BUS_DEV_RESET = 0x81
|
|
} bt_ccb_opcode_t;
|
|
|
|
typedef enum {
|
|
BTSTAT_NOERROR = 0x00,
|
|
BTSTAT_LINKED_CMD_COMPLETE = 0x0A,
|
|
BTSTAT_LINKED_CMD_FLAG_COMPLETE = 0x0B,
|
|
BTSTAT_DATAUNDERUN_ERROR = 0x0C,
|
|
BTSTAT_SELTIMEOUT = 0x11,
|
|
BTSTAT_DATARUN_ERROR = 0x12,
|
|
BTSTAT_UNEXPECTED_BUSFREE = 0x13,
|
|
BTSTAT_INVALID_PHASE = 0x14,
|
|
BTSTAT_INVALID_ACTION_CODE = 0x15,
|
|
BTSTAT_INVALID_OPCODE = 0x16,
|
|
BTSTAT_LINKED_CCB_LUN_MISMATCH = 0x17,
|
|
BTSTAT_INVALID_CCB_OR_SG_PARAM = 0x1A,
|
|
BTSTAT_AUTOSENSE_FAILED = 0x1B,
|
|
BTSTAT_TAGGED_MSG_REJECTED = 0x1C,
|
|
BTSTAT_UNSUPPORTED_MSG_RECEIVED = 0x1D,
|
|
BTSTAT_HARDWARE_FAILURE = 0x20,
|
|
BTSTAT_TARGET_IGNORED_ATN = 0x21,
|
|
BTSTAT_HA_SCSI_BUS_RESET = 0x22,
|
|
BTSTAT_OTHER_SCSI_BUS_RESET = 0x23,
|
|
BTSTAT_INVALID_RECONNECT = 0x24,
|
|
BTSTAT_HA_BDR = 0x25,
|
|
BTSTAT_ABORT_QUEUE_GENERATED = 0x26,
|
|
BTSTAT_HA_SOFTWARE_ERROR = 0x27,
|
|
BTSTAT_HA_WATCHDOG_ERROR = 0x28,
|
|
BTSTAT_SCSI_PERROR_DETECTED = 0x30
|
|
} btstat_t;
|
|
|
|
struct bt_hccb {
|
|
u_int8_t opcode;
|
|
u_int8_t :3,
|
|
datain :1,
|
|
dataout :1,
|
|
wide_tag_enable :1, /* Wide Lun CCB format */
|
|
wide_tag_type :2; /* Wide Lun CCB format */
|
|
u_int8_t cmd_len;
|
|
u_int8_t sense_len;
|
|
int32_t data_len; /* residuals can be negative */
|
|
u_int32_t data_addr;
|
|
u_int8_t reserved[2];
|
|
u_int8_t btstat;
|
|
u_int8_t sdstat;
|
|
u_int8_t target_id;
|
|
u_int8_t target_lun :5,
|
|
tag_enable :1,
|
|
tag_type :2;
|
|
u_int8_t scsi_cdb[12];
|
|
u_int8_t reserved2[6];
|
|
u_int32_t sense_addr;
|
|
};
|
|
|
|
typedef enum {
|
|
BCCB_FREE = 0x0,
|
|
BCCB_ACTIVE = 0x1,
|
|
BCCB_DEVICE_RESET = 0x2,
|
|
BCCB_RELEASE_SIMQ = 0x4
|
|
} bccb_flags_t;
|
|
|
|
struct bt_ccb {
|
|
struct bt_hccb hccb;
|
|
SLIST_ENTRY(bt_ccb) links;
|
|
u_int32_t flags;
|
|
union ccb *ccb;
|
|
bus_dmamap_t dmamap;
|
|
struct callout timer;
|
|
bt_sg_t *sg_list;
|
|
u_int32_t sg_list_phys;
|
|
};
|
|
|
|
struct sg_map_node {
|
|
bus_dmamap_t sg_dmamap;
|
|
bus_addr_t sg_physaddr;
|
|
bt_sg_t* sg_vaddr;
|
|
SLIST_ENTRY(sg_map_node) links;
|
|
};
|
|
|
|
struct bt_softc {
|
|
device_t dev;
|
|
struct resource *port;
|
|
struct resource *irq;
|
|
struct resource *drq;
|
|
void *ih;
|
|
struct mtx lock;
|
|
struct cam_sim *sim;
|
|
struct cam_path *path;
|
|
bt_mbox_out_t *cur_outbox;
|
|
bt_mbox_in_t *cur_inbox;
|
|
bt_mbox_out_t *last_outbox;
|
|
bt_mbox_in_t *last_inbox;
|
|
struct bt_ccb *bt_ccb_array;
|
|
SLIST_HEAD(,bt_ccb) free_bt_ccbs;
|
|
LIST_HEAD(,ccb_hdr) pending_ccbs;
|
|
u_int active_ccbs;
|
|
u_int32_t bt_ccb_physbase;
|
|
bt_mbox_in_t *in_boxes;
|
|
bt_mbox_out_t *out_boxes;
|
|
struct scsi_sense_data *sense_buffers;
|
|
u_int32_t sense_buffers_physbase;
|
|
struct bt_ccb *recovery_bccb;
|
|
u_int num_boxes;
|
|
bus_dma_tag_t parent_dmat; /*
|
|
* All dmat's derive from
|
|
* the dmat defined by our
|
|
* bus.
|
|
*/
|
|
bus_dma_tag_t buffer_dmat; /* dmat for buffer I/O */
|
|
bus_dma_tag_t mailbox_dmat; /* dmat for our mailboxes */
|
|
bus_dmamap_t mailbox_dmamap;
|
|
bus_dma_tag_t ccb_dmat; /* dmat for our ccb array */
|
|
bus_dmamap_t ccb_dmamap;
|
|
bus_dma_tag_t sg_dmat; /* dmat for our sg segments */
|
|
bus_dma_tag_t sense_dmat; /* dmat for our sense buffers */
|
|
bus_dmamap_t sense_dmamap;
|
|
SLIST_HEAD(, sg_map_node) sg_maps;
|
|
bus_addr_t mailbox_physbase;
|
|
bus_addr_t mailbox_addrlimit;
|
|
u_int num_ccbs; /* Number of CCBs malloc'd */
|
|
u_int max_ccbs; /* Maximum allocatable CCBs */
|
|
u_int max_sg;
|
|
u_int scsi_id;
|
|
u_int32_t extended_trans :1,
|
|
wide_bus :1,
|
|
diff_bus :1,
|
|
ultra_scsi :1,
|
|
extended_lun :1,
|
|
strict_rr :1,
|
|
tag_capable :1,
|
|
wide_lun_ccb :1,
|
|
resource_shortage :1,
|
|
level_trigger_ints:1,
|
|
:22;
|
|
u_int16_t tags_permitted;
|
|
u_int16_t disc_permitted;
|
|
u_int16_t sync_permitted;
|
|
u_int16_t fast_permitted;
|
|
u_int16_t ultra_permitted;
|
|
u_int16_t wide_permitted;
|
|
u_int8_t init_level;
|
|
volatile u_int8_t command_cmp;
|
|
volatile u_int8_t latched_status;
|
|
u_int32_t bios_addr;
|
|
char firmware_ver[6];
|
|
char model[5];
|
|
};
|
|
|
|
#define BT_TEMP_UNIT 0xFF /* Unit for probes */
|
|
void bt_init_softc(device_t dev,
|
|
struct resource *port,
|
|
struct resource *irq,
|
|
struct resource *drq);
|
|
void bt_free_softc(device_t dev);
|
|
int bt_port_probe(device_t dev,
|
|
struct bt_probe_info *info);
|
|
int bt_probe(device_t dev);
|
|
int bt_fetch_adapter_info(device_t dev);
|
|
int bt_init(device_t dev);
|
|
int bt_attach(device_t dev);
|
|
void bt_intr(void *arg);
|
|
int bt_check_probed_iop(u_int ioport);
|
|
void bt_mark_probed_bio(isa_compat_io_t port);
|
|
void bt_mark_probed_iop(u_int ioport);
|
|
void bt_find_probe_range(int ioport,
|
|
int *port_index,
|
|
int *max_port_index);
|
|
|
|
int bt_iop_from_bio(isa_compat_io_t bio_index);
|
|
|
|
#define DEFAULT_CMD_TIMEOUT 100000 /* 10 sec */
|
|
int bt_cmd(struct bt_softc *bt, bt_op_t opcode,
|
|
u_int8_t *params, u_int param_len,
|
|
u_int8_t *reply_data, u_int reply_len,
|
|
u_int cmd_timeout);
|
|
|
|
#define bt_name(bt) device_get_nameunit(bt->dev)
|
|
|
|
#define bt_inb(bt, reg) \
|
|
bus_read_1((bt)->port, reg)
|
|
|
|
#define bt_outb(bt, reg, value) \
|
|
bus_write_1((bt)->port, reg, value)
|
|
|
|
#endif /* _BT_H_ */
|