179 lines
5.0 KiB
Plaintext
179 lines
5.0 KiB
Plaintext
# This is a placeholder until the hardware support is complete.
|
|
|
|
# I'm assuming this is an AP135-020. The AP136-010 in openwrt has
|
|
# the ethernet ports wired up to the switch in the reverse way.
|
|
|
|
# $FreeBSD$
|
|
|
|
# QCA955X_ETH_CFG_RGMII_EN (1 << 0)
|
|
hint.qca955x_gmac.0.gmac_cfg=0x1
|
|
|
|
# mdiobus0 on arge0
|
|
hint.argemdio.0.at="nexus0"
|
|
hint.argemdio.0.maddr=0x19000000
|
|
hint.argemdio.0.msize=0x1000
|
|
hint.argemdio.0.order=0
|
|
|
|
# mdiobus1 on arge1 - required to bring up arge1?
|
|
hint.argemdio.1.at="nexus0"
|
|
hint.argemdio.1.maddr=0x1a000000
|
|
hint.argemdio.1.msize=0x1000
|
|
hint.argemdio.1.order=0
|
|
|
|
# AR8327 - connected via mdiobus0 on arge0
|
|
hint.arswitch.0.at="mdio0"
|
|
hint.arswitch.0.is_7240=0 # definitely not the internal switch!
|
|
hint.arswitch.0.is_9340=0 # not the internal switch!
|
|
hint.arswitch.0.numphys=5 # all ports are PHYs
|
|
hint.arswitch.0.phy4cpu=0
|
|
hint.arswitch.0.is_rgmii=0 # not needed
|
|
hint.arswitch.0.is_gmii=0 # not needed
|
|
|
|
# This is where it gets a bit odd. port 0 and port 6 are CPU ports.
|
|
# The current code only supports one CPU port. So hm, what should
|
|
# we do to hook PAD6 up to be RGMII but a PHY, not a MAC?
|
|
|
|
# The other trick - how do we get arge1 (hooked up to GMAC0) to work?
|
|
# That's currently supposed to be hooked up to CPU port 0.
|
|
|
|
# Other AR8327 configuration parameters
|
|
|
|
# AP136-020 parameters
|
|
|
|
# GMAC0 AR8327 -> GMAC1 (arge1) SoC, SGMII
|
|
|
|
# AR8327_PAD_MAC_SGMII
|
|
hint.arswitch.0.pad.0.mode=3
|
|
#hint.arswitch.0.pad.0.rxclk_delay_sel=0
|
|
hint.arswitch.0.pad.0.sgmii_delay_en=1
|
|
|
|
# GMAC6 AR8327 -> GMAC0 (arge0) SoC, RGMII
|
|
|
|
# AR8327_PAD_MAC_RGMII
|
|
# XXX I think this hooks it up to the internal MAC6
|
|
hint.arswitch.0.pad.6.mode=6
|
|
hint.arswitch.0.pad.6.txclk_delay_en=1
|
|
hint.arswitch.0.pad.6.rxclk_delay_en=1
|
|
# AR8327_CLK_DELAY_SEL1
|
|
hint.arswitch.0.pad.6.txclk_delay_sel=1
|
|
# AR8327_CLK_DELAY_SEL2
|
|
hint.arswitch.0.pad.6.rxclk_delay_sel=2
|
|
|
|
# XXX there's no LED management just yet!
|
|
hint.arswitch.0.led.ctrl0=0x00000000
|
|
hint.arswitch.0.led.ctrl1=0xc737c737
|
|
hint.arswitch.0.led.ctrl2=0x00000000
|
|
hint.arswitch.0.led.ctrl3=0x00c30c00
|
|
hint.arswitch.0.led.open_drain=1
|
|
|
|
# force_link=1 is required for the rest of the parameters
|
|
# to be configured.
|
|
hint.arswitch.0.port.0.force_link=1
|
|
hint.arswitch.0.port.0.speed=1000
|
|
hint.arswitch.0.port.0.duplex=1
|
|
hint.arswitch.0.port.0.txpause=1
|
|
hint.arswitch.0.port.0.rxpause=1
|
|
|
|
# force_link=1 is required for the rest of the parameters
|
|
# to be configured.
|
|
hint.arswitch.0.port.6.force_link=1
|
|
hint.arswitch.0.port.6.speed=1000
|
|
hint.arswitch.0.port.6.duplex=1
|
|
hint.arswitch.0.port.6.txpause=1
|
|
hint.arswitch.0.port.6.rxpause=1
|
|
|
|
# arge0 - hooked up to AR8327 GMAC6, RGMII
|
|
# set at 1000/full to the switch.
|
|
# so, lock both sides of this connect up to 1000/full;
|
|
# if_arge thus wont change the PLL configuration
|
|
# upon a link status change.
|
|
hint.arge.0.phymask=0x0
|
|
hint.arge.0.miimode=3 # RGMII
|
|
hint.arge.0.media=1000
|
|
hint.arge.0.fduplex=1
|
|
hint.arge.0.pll_1000=0x56000000
|
|
|
|
# MAC for arge0 is the first 6 bytes of the ART
|
|
hint.arge.0.eeprommac=0x1fff0000
|
|
|
|
# arge1 - lock up to 1000/full
|
|
hint.arge.1.phymask=0x0
|
|
hint.arge.1.media=1000
|
|
hint.arge.1.fduplex=1
|
|
hint.arge.1.miimode=5 # SGMII
|
|
hint.arge.1.pll_1000=0x03000101
|
|
|
|
# MAC for arge1 is the second 6 bytes of the ART
|
|
hint.arge.1.eeprommac=0x1fff0006
|
|
|
|
# ath0: Where the ART is - last 64k in the flash
|
|
hint.ath.0.eepromaddr=0x1fff0000
|
|
hint.ath.0.eepromsize=16384
|
|
|
|
# ath1: it's different; it's a PCIe attached device, so
|
|
# we instead need to teach the PCIe bridge code about it
|
|
# (ie, the 'early pci fixup' stuff that programs the PCIe
|
|
# host registers on the NIC) and then we teach ath where
|
|
# to find it.
|
|
|
|
# ath1 hint - pcie slot 0
|
|
# hint.pcib.0.bus.0.0.0.ath_fixup_addr=0x1fff4000
|
|
# hint.pcib.0.bus.0.0.0.ath_fixup_size=16384
|
|
|
|
# ath0 - eeprom comes from here
|
|
# hint.ath.1.eeprom_firmware="pcib.0.bus.0.0.0.eeprom_firmware"
|
|
|
|
# flash layout:
|
|
#
|
|
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),8256k(mib0),64k(ART)
|
|
|
|
|
|
# 256KiB u-boot
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x00040000 # 256k u-boot
|
|
hint.map.0.name="u-boot"
|
|
hint.map.0.readonly=1
|
|
|
|
# 64KiB u-boot-env
|
|
hint.map.1.at="flash/spi0"
|
|
hint.map.1.start=0x00040000
|
|
hint.map.1.end=0x00050000 # 64k u-boot-env
|
|
hint.map.1.name="u-boot-env"
|
|
hint.map.1.readonly=1
|
|
|
|
# 6336KiB rootfs
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start=0x00050000
|
|
hint.map.2.end=0x00680000 # 6336k rootfs
|
|
hint.map.2.name="rootfs"
|
|
hint.map.2.readonly=1
|
|
|
|
# 1344KiB uImage
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start=0x00680000
|
|
hint.map.3.end=0x007d0000 # 1408k uImage, 64k off the end..
|
|
hint.map.3.name="uImage"
|
|
hint.map.3.readonly=1
|
|
|
|
# 64KiB cfg
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x007d0000
|
|
hint.map.4.end=0x007e0000
|
|
hint.map.4.name="cfg"
|
|
hint.map.4.readonly=0
|
|
|
|
# 8256 KiB mib0
|
|
hint.map.5.at="flash/spi0"
|
|
hint.map.5.start=0x007e0000
|
|
hint.map.5.end=0x00ff0000 # 64k mib0
|
|
hint.map.5.name="mib0"
|
|
hint.map.5.readonly=1
|
|
|
|
# 64KiB ART
|
|
hint.map.6.at="flash/spi0"
|
|
hint.map.6.start=0x007f0000
|
|
hint.map.6.end=0x01000000 # 64k ART
|
|
hint.map.6.name="ART"
|
|
hint.map.6.readonly=1
|