d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
18c72666ce
freebsd-skq/sys/dev/mii/e1000phy.c

501 lines
14 KiB
C
Raw Normal View History

Start each of the license/copyright comments with /*-, minor shuffle of lines
2005-01-06 01:43:34 +00:00
/*-
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
* Principal Author: Parag Patel
* Copyright (c) 2001
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice unmodified, this list of conditions, and the following
* disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
Correct spelling in comments. Submitted by: brucec
2011-04-22 09:22:27 +00:00
* Additional Copyright (c) 2001 by Traakan Software under same licence.
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
* Secondary Author: Matthew Jacob
*/
Move __FBSDID out from under a comment.
2004-05-29 17:45:45 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
/*
* driver for the Marvell 88E1000 series external 1000/100/10-BT PHY.
*/
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
/*
* Support added for the Marvell 88E1011 (Alaska) 1000/100/10baseTX and
* 1000baseSX PHY.
* Nathan Binkert <nate@openbsd.org>
* Jung-uk Kim <jkim@niksun.com>
*/
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
Add some missing <sys/module.h> includes which are masked by the one on death-row in <sys/kernel.h>
2004-05-30 17:57:46 +00:00
#include <sys/module.h>
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
#include <sys/socket.h>
#include <sys/bus.h>
#include <net/if.h>
The MII layer shouldn't care about administrative status of an interface. Make MII drivers forget about 'struct ifnet'. Later plan is to provide an administrative downcall from ifnet layer into drivers, to inform them about administrative status change. If someone thinks that processing MII events for an administratively down interface is a big problem, then drivers would turn MII processing off. The following MII drivers do evil things, like strcmp() on driver name, so they still need knowledge of ifnet and thus include if_var.h. They all need to be fixed: sys/dev/mii/brgphy.c sys/dev/mii/e1000phy.c sys/dev/mii/ip1000phy.c sys/dev/mii/jmphy.c sys/dev/mii/nsphy.c sys/dev/mii/rgephy.c sys/dev/mii/truephy.c Sponsored by: Netflix Sponsored by: Nginx, Inc.
2013-10-26 18:40:17 +00:00
#include <net/if_var.h>
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
Remove miidevs.h and generate it from miidevs at compile time. The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
#include "miidevs.h"
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
#include <dev/mii/e1000phyreg.h>
#include "miibus_if.h"
style(9)
2006-12-11 10:22:24 +00:00
static int e1000phy_probe(device_t);
static int e1000phy_attach(device_t);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
static device_method_t e1000phy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, e1000phy_probe),
DEVMETHOD(device_attach, e1000phy_attach),
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
DEVMETHOD(device_detach, mii_phy_detach),
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
DEVMETHOD(device_shutdown, bus_generic_shutdown),
Use DEVMETHOD_END.
2011-11-23 20:27:26 +00:00
DEVMETHOD_END
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
};
static devclass_t e1000phy_devclass;
static driver_t e1000phy_driver = {
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
"e1000phy",
e1000phy_methods,
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
sizeof(struct mii_softc)
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
};
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
DRIVER_MODULE(e1000phy, miibus, e1000phy_driver, e1000phy_devclass, 0, 0);
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int e1000phy_service(struct mii_softc *, struct mii_data *, int);
static void e1000phy_status(struct mii_softc *);
static void e1000phy_reset(struct mii_softc *);
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
static int e1000phy_mii_phy_auto(struct mii_softc *, int);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
static const struct mii_phydesc e1000phys[] = {
MII_PHY_DESC(MARVELL, E1000),
MII_PHY_DESC(MARVELL, E1011),
MII_PHY_DESC(MARVELL, E1000_3),
MII_PHY_DESC(MARVELL, E1000_5),
MII_PHY_DESC(MARVELL, E1111),
MII_PHY_DESC(xxMARVELL, E1000),
MII_PHY_DESC(xxMARVELL, E1011),
MII_PHY_DESC(xxMARVELL, E1000_3),
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxMARVELL, E1000S),
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
MII_PHY_DESC(xxMARVELL, E1000_5),
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxMARVELL, E1101),
MII_PHY_DESC(xxMARVELL, E3082),
MII_PHY_DESC(xxMARVELL, E1112),
MII_PHY_DESC(xxMARVELL, E1149),
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
MII_PHY_DESC(xxMARVELL, E1111),
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxMARVELL, E1116),
MII_PHY_DESC(xxMARVELL, E1116R),
Add support for 88E1116R. Sponsored by: Plat'Home, Co.,Ltd.
2012-07-28 21:59:12 +00:00
MII_PHY_DESC(xxMARVELL, E1116R_29),
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxMARVELL, E1118),
Recognize the Marvell 88E1145 Quad Gigabit PHY.
2012-10-29 00:17:12 +00:00
MII_PHY_DESC(xxMARVELL, E1145),
Add detection for the Marvel 88E1149R and treat it just like the 88E1149.
2011-06-30 05:20:02 +00:00
MII_PHY_DESC(xxMARVELL, E1149R),
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxMARVELL, E3016),
MII_PHY_DESC(xxMARVELL, PHYG65G),
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
MII_PHY_END
};
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
static const struct mii_phy_funcs e1000phy_funcs = {
e1000phy_service,
e1000phy_status,
e1000phy_reset
};
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
static int
e1000phy_probe(device_t dev)
{
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
return (mii_phy_dev_probe(dev, e1000phys, BUS_PROBE_DEFAULT));
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
static int
e1000phy_attach(device_t dev)
{
struct mii_softc *sc;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
sc = device_get_softc(dev);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
mii_phy_dev_attach(dev, MIIF_NOMANPAUSE, &e1000phy_funcs, 0);
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
- Remove unused variable. - Wrap long line.
2015-01-13 06:22:55 +00:00
if (mii_dev_mac_match(dev, "msk") &&
(sc->mii_flags & MIIF_MACPRIV0) != 0)
Convert the PHY drivers to honor the mii_flags passed down and convert the NIC drivers as well as the PHY drivers to take advantage of the mii_attach() introduced in r213878 to get rid of certain hacks. For the most part these were: - Artificially limiting miibus_{read,write}reg methods to certain PHY addresses; we now let mii_attach() only probe the PHY at the desired address(es) instead. - PHY drivers setting MIIF_* flags based on the NIC driver they hang off from, partly even based on grabbing and using the softc of the parent; we now pass these flags down from the NIC to the PHY drivers via mii_attach(). This got us rid of all such hacks except those of brgphy() in combination with bce(4) and bge(4), which is way beyond what can be expressed with simple flags. While at it, I took the opportunity to change the NIC drivers to pass up the error returned by mii_attach() (previously by mii_phy_probe()) and unify the error message used in this case where and as appropriate as mii_attach() actually can fail for a number of reasons, not just because of no PHY(s) being present at the expected address(es). Reviewed by: jhb, yongari
2010-10-15 14:52:11 +00:00
sc->mii_flags |= MIIF_PHYPRIV0;
Add hack to pass controller specific information to phy driver. Unlike most other PHYs there is no easy way to know which media type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now passed via bus-specific instance variable of a device. While I'm here add 88E1112 specific work around to set SIGDET polarity low. Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly gave remote access to system with DGE-560SX.
2009-09-28 21:03:28 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
switch (sc->mii_mpd_model) {
case MII_MODEL_xxMARVELL_E1011:
case MII_MODEL_xxMARVELL_E1112:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
if (PHY_READ(sc, E1000_ESSR) & E1000_ESSR_FIBER_LINK)
sc->mii_flags |= MIIF_HAVEFIBER;
break;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E1149:
Add detection for the Marvel 88E1149R and treat it just like the 88E1149.
2011-06-30 05:20:02 +00:00
case MII_MODEL_xxMARVELL_E1149R:
Some 88E1149 PHY's page select is initialized to point to other bank instead of copper/fiber bank which in turn resulted in wrong registers were accessed during PHY operation. It is believed that page 0 should be used for copper PHY so reinitialize E1000_EADR to select default copper PHY. This fixes link establishment issue of nfe(4) on Sun Fire X4140. OpenBSD also has similimar patch but they just reset the E1000_EADR register to page 0. However some Marvell PHYs((88E3082, 88E1000) don't have the extended address register and the meaning of the register is quite different for each PHY model. So selecting copper PHY is limited to 88E1149 PHY which seems to be the only one that exhibits link establishment problem. If parent device know the type of PHY(either copper or fiber) that information should be notified to PHY driver but there is no good way to pass this information yet. Reported by: thompsa Reviewed by: thompsa
2008-10-17 05:26:51 +00:00
/*
* Some 88E1149 PHY's page select is initialized to
* point to other bank instead of copper/fiber bank
* which in turn resulted in wrong registers were
* accessed during PHY operation. It is believed that
* page 0 should be used for copper PHY so reinitialize
* E1000_EADR to select default copper PHY. If parent
* device know the type of PHY(either copper or fiber),
* that information should be used to select default
* type of PHY.
*/
PHY_WRITE(sc, E1000_EADR, 0);
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_RESET(sc);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
sc->mii_capabilities = PHY_READ(sc, MII_BMSR) & sc->mii_capmask;
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
if (sc->mii_capabilities & BMSR_EXTSTAT) {
Use mii_phy_add_media() and remove usage of local macro ADD. Also checks extended status register to see whether the PHY is fast ethernet or not. This removes a lot of checks for specific PHY models and it makes easy to add more PHYs to e1000phy(4). While I'm here remove setting mii_anegticks as it is set with mii_phy_add_media().
2009-05-25 01:41:05 +00:00
sc->mii_extcapabilities = PHY_READ(sc, MII_EXTSR);
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
if ((sc->mii_extcapabilities &
(EXTSR_1000TFDX | EXTSR_1000THDX)) != 0)
sc->mii_flags |= MIIF_HAVE_GTCR;
}
Change the order that we print the media options during device probe to match the other mii drivers.
2001-09-29 18:59:17 +00:00
device_printf(dev, " ");
Use mii_phy_add_media() and remove usage of local macro ADD. Also checks extended status register to see whether the PHY is fast ethernet or not. This removes a lot of checks for specific PHY models and it makes easy to add more PHYs to e1000phy(4). While I'm here remove setting mii_anegticks as it is set with mii_phy_add_media().
2009-05-25 01:41:05 +00:00
mii_phy_add_media(sc);
printf("\n");
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
MIIBUS_MEDIAINIT(sc->mii_dev);
style(9)
2006-12-11 10:22:24 +00:00
return (0);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
static void
e1000phy_reset(struct mii_softc *sc)
{
Save extended address register prior to switching to 1000BASE-X only mode and restore original value of extended address register instead of overwriting it with page 1. There are still instance information passing issue(e.g configured media type: fiber or copper) from driver to PHY layer but this change make the selected PHY work with 88E1112 PHY. Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl > Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
2008-09-30 08:18:38 +00:00
uint16_t reg, page;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
reg = PHY_READ(sc, E1000_SCR);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
if ((sc->mii_flags & MIIF_HAVEFIBER) != 0) {
reg &= ~E1000_SCR_AUTO_X_MODE;
PHY_WRITE(sc, E1000_SCR, reg);
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if (sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1112) {
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
/* Select 1000BASE-X only mode. */
Save extended address register prior to switching to 1000BASE-X only mode and restore original value of extended address register instead of overwriting it with page 1. There are still instance information passing issue(e.g configured media type: fiber or copper) from driver to PHY layer but this change make the selected PHY work with 88E1112 PHY. Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl > Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
2008-09-30 08:18:38 +00:00
page = PHY_READ(sc, E1000_EADR);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
PHY_WRITE(sc, E1000_EADR, 2);
reg = PHY_READ(sc, E1000_SCR);
reg &= ~E1000_SCR_MODE_MASK;
reg |= E1000_SCR_MODE_1000BX;
PHY_WRITE(sc, E1000_SCR, reg);
Correct a bug in r213893; within a PHY driver MIIF_PHYPRIVn should be used instead of MIIF_MACPRIVn. This didn't make a functional difference though.
2010-10-30 20:51:25 +00:00
if ((sc->mii_flags & MIIF_PHYPRIV0) != 0) {
Add hack to pass controller specific information to phy driver. Unlike most other PHYs there is no easy way to know which media type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now passed via bus-specific instance variable of a device. While I'm here add 88E1112 specific work around to set SIGDET polarity low. Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly gave remote access to system with DGE-560SX.
2009-09-28 21:03:28 +00:00
/* Set SIGDET polarity low for SFP module. */
PHY_WRITE(sc, E1000_EADR, 1);
reg = PHY_READ(sc, E1000_SCR);
reg |= E1000_SCR_FIB_SIGDET_POLARITY;
PHY_WRITE(sc, E1000_SCR, reg);
}
Save extended address register prior to switching to 1000BASE-X only mode and restore original value of extended address register instead of overwriting it with page 1. There are still instance information passing issue(e.g configured media type: fiber or copper) from driver to PHY layer but this change make the selected PHY work with 88E1112 PHY. Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl > Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
2008-09-30 08:18:38 +00:00
PHY_WRITE(sc, E1000_EADR, page);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
}
} else {
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
switch (sc->mii_mpd_model) {
case MII_MODEL_xxMARVELL_E1111:
case MII_MODEL_xxMARVELL_E1112:
case MII_MODEL_xxMARVELL_E1116:
Add support for 88E1116R. Sponsored by: Plat'Home, Co.,Ltd.
2012-07-28 21:59:12 +00:00
case MII_MODEL_xxMARVELL_E1116R_29:
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E1118:
case MII_MODEL_xxMARVELL_E1149:
Add detection for the Marvel 88E1149R and treat it just like the 88E1149.
2011-06-30 05:20:02 +00:00
case MII_MODEL_xxMARVELL_E1149R:
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_PHYG65G:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
/* Disable energy detect mode. */
reg &= ~E1000_SCR_EN_DETECT_MASK;
reg |= E1000_SCR_AUTO_X_MODE;
Add support for 88E1116R. Sponsored by: Plat'Home, Co.,Ltd.
2012-07-28 21:59:12 +00:00
if (sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1116 ||
sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1116R_29)
Add 88E1116/88E1116R PHY support code that takes the PHY out of power-down mode. PR: kern/114086 MFC after: 3 days
2007-10-29 05:50:22 +00:00
reg &= ~E1000_SCR_POWER_DOWN;
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
reg |= E1000_SCR_ASSERT_CRS_ON_TX;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
break;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E3082:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
reg |= (E1000_SCR_AUTO_X_MODE >> 1);
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
reg |= E1000_SCR_ASSERT_CRS_ON_TX;
break;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E3016:
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
reg |= E1000_SCR_AUTO_MDIX;
reg &= ~(E1000_SCR_EN_DETECT |
E1000_SCR_SCRAMBLER_DISABLE);
reg |= E1000_SCR_LPNP;
/* XXX Enable class A driver for Yukon FE+ A0. */
PHY_WRITE(sc, 0x1C, PHY_READ(sc, 0x1C) | 0x0001);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
default:
reg &= ~E1000_SCR_AUTO_X_MODE;
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
reg |= E1000_SCR_ASSERT_CRS_ON_TX;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
break;
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if (sc->mii_mpd_model != MII_MODEL_xxMARVELL_E3016) {
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
/* Auto correction for reversed cable polarity. */
reg &= ~E1000_SCR_POLARITY_REVERSAL;
}
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
PHY_WRITE(sc, E1000_SCR, reg);
Add 88E1116/88E1116R PHY support code that takes the PHY out of power-down mode. PR: kern/114086 MFC after: 3 days
2007-10-29 05:50:22 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if (sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1116 ||
Add support for 88E1116R. Sponsored by: Plat'Home, Co.,Ltd.
2012-07-28 21:59:12 +00:00
sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1116R_29 ||
Add detection for the Marvel 88E1149R and treat it just like the 88E1149.
2011-06-30 05:20:02 +00:00
sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1149 ||
sc->mii_mpd_model == MII_MODEL_xxMARVELL_E1149R) {
Add 88E1116/88E1116R PHY support code that takes the PHY out of power-down mode. PR: kern/114086 MFC after: 3 days
2007-10-29 05:50:22 +00:00
PHY_WRITE(sc, E1000_EADR, 2);
reg = PHY_READ(sc, E1000_SCR);
reg |= E1000_SCR_RGMII_POWER_UP;
PHY_WRITE(sc, E1000_SCR, reg);
Backout r193289. r193289 restored page select bits to previous value instead of blindly resetting it to 0. However, it seems page select bits of some 88E1116 PHY is initialized to invalid one such that restoring page select bits after programming broke MII register access. The correct solution would be reset page select bits to 0 in PHY attach stage but it would require more testing. Since we're in BETA stage such a change would be dangerous so just back it out. This change should fix nfe(4) breakage on NVIDIA MCP55. Reported by: Ryan Rogers < webmaster <> doghouserepair dot com > Sam Fourman Jr. < sfourman <> gmail dot com > Tested by: Ryan Rogers < webmaster <> doghouserepair dot com > Sam Fourman Jr. < sfourman <> gmail dot com > Approved by: re (kib)
2009-08-18 20:20:15 +00:00
PHY_WRITE(sc, E1000_EADR, 0);
Add 88E1116/88E1116R PHY support code that takes the PHY out of power-down mode. PR: kern/114086 MFC after: 3 days
2007-10-29 05:50:22 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
switch (sc->mii_mpd_model) {
case MII_MODEL_xxMARVELL_E3082:
case MII_MODEL_xxMARVELL_E1112:
case MII_MODEL_xxMARVELL_E1118:
Program LED registers for 88E1116/88E1149 PHYs. These PHYs are found on Marvell Yukon Ultra, Marvell Yukon Extreme controllers. While I'm here explicitly issue 'powerup' command for 88E1149 PHY. Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
2009-06-02 00:30:30 +00:00
break;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E1116:
Add support for 88E1116R. Sponsored by: Plat'Home, Co.,Ltd.
2012-07-28 21:59:12 +00:00
case MII_MODEL_xxMARVELL_E1116R_29:
Program LED registers for 88E1116/88E1149 PHYs. These PHYs are found on Marvell Yukon Ultra, Marvell Yukon Extreme controllers. While I'm here explicitly issue 'powerup' command for 88E1149 PHY. Tested by: jhb, Warren Block ( wblock <> wonkity dot com )
2009-06-02 00:30:30 +00:00
page = PHY_READ(sc, E1000_EADR);
/* Select page 3, LED control register. */
PHY_WRITE(sc, E1000_EADR, 3);
PHY_WRITE(sc, E1000_SCR,
E1000_SCR_LED_LOS(1) | /* Link/Act */
E1000_SCR_LED_INIT(8) | /* 10Mbps */
E1000_SCR_LED_STAT1(7) | /* 100Mbps */
E1000_SCR_LED_STAT0(7)); /* 1000Mbps */
/* Set blink rate. */
PHY_WRITE(sc, E1000_IER, E1000_PULSE_DUR(E1000_PULSE_170MS) |
E1000_BLINK_RATE(E1000_BLINK_84MS));
PHY_WRITE(sc, E1000_EADR, page);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
break;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
case MII_MODEL_xxMARVELL_E3016:
Add driver support for 88E3016 PHY which is found on Marvell Yukon FE+ controller. Due to the severe silicon bugs for Yukon FE+, 88E3016 seems to require more workarounds. However I'm not sure whether the workaround is PHY specific or only applicable to Yukon FE+. The datasheet for the PHY is publicly available but it lacks several details for the workaround used in this change. The workaround information was obtained from Linux. Many thanks to Yukon FE+ users who helped me add 88E3016 support. Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com ) Bruce Cran ( bruce <> cran dot org dot uk ) Michael Reifenberger ( mike <> reifenberger dot com ) Stephen Montgomery-Smith ( stephen <> missouri dot edu )
2009-05-25 02:36:29 +00:00
/* LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED. */
PHY_WRITE(sc, 0x16, 0x0B << 8 | 0x05 << 4 | 0x04);
/* Integrated register calibration workaround. */
PHY_WRITE(sc, 0x1D, 17);
PHY_WRITE(sc, 0x1E, 0x3F60);
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
default:
/* Force TX_CLK to 25MHz clock. */
reg = PHY_READ(sc, E1000_ESCR);
reg |= E1000_ESCR_TX_CLK_25;
PHY_WRITE(sc, E1000_ESCR, reg);
break;
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
/* Reset the PHY so all changes take effect. */
reg = PHY_READ(sc, E1000_CR);
reg |= E1000_CR_RESET;
PHY_WRITE(sc, E1000_CR, reg);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
e1000phy_service(struct mii_softc *sc, struct mii_data *mii, int cmd)
{
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
uint16_t speed, gig;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
int reg;
switch (cmd) {
case MII_POLLSTAT:
break;
case MII_MEDIACHG:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
if (IFM_SUBTYPE(ife->ifm_media) == IFM_AUTO) {
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
e1000phy_mii_phy_auto(sc, ife->ifm_media);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
speed = 0;
switch (IFM_SUBTYPE(ife->ifm_media)) {
Follow NetBSD and s/IFM_1000_TX/IFM_1000_T/
2002-04-28 20:34:20 +00:00
case IFM_1000_T:
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
if ((sc->mii_flags & MIIF_HAVE_GTCR) == 0)
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
return (EINVAL);
speed = E1000_CR_SPEED_1000;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
break;
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
case IFM_1000_SX:
Use mii_phy_add_media() and remove usage of local macro ADD. Also checks extended status register to see whether the PHY is fast ethernet or not. This removes a lot of checks for specific PHY models and it makes easy to add more PHYs to e1000phy(4). While I'm here remove setting mii_anegticks as it is set with mii_phy_add_media().
2009-05-25 01:41:05 +00:00
if ((sc->mii_extcapabilities &
(EXTSR_1000XFDX | EXTSR_1000XHDX)) == 0)
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
return (EINVAL);
speed = E1000_CR_SPEED_1000;
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
break;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
case IFM_100_TX:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
speed = E1000_CR_SPEED_100;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
break;
case IFM_10_T:
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
speed = E1000_CR_SPEED_10;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
case IFM_NONE:
reg = PHY_READ(sc, E1000_CR);
PHY_WRITE(sc, E1000_CR,
reg | E1000_CR_ISOLATE | E1000_CR_POWER_DOWN);
goto done;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
default:
return (EINVAL);
}
- Masking IFM_GMASK when also masking IFM_FDX is redundant and just complicates the code. - Don't let atphy_setmedia() announce PAUSE support for half-duplex when MIIF_FORCEPAUSE is set. - Simplify e1000phy_service() and ip1000phy_service() to only set the manual configuration bits once after we have figured them all out. For ip1000phy_service() this also means we no longer unnecessarily update the hardware along the road. MFC after: 1 week
2011-01-14 19:16:59 +00:00
if ((ife->ifm_media & IFM_FDX) != 0) {
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
speed |= E1000_CR_FULL_DUPLEX;
gig = E1000_1GCR_1000T_FD;
} else
gig = E1000_1GCR_1000T;
reg = PHY_READ(sc, E1000_CR);
reg &= ~E1000_CR_AUTO_NEG_ENABLE;
PHY_WRITE(sc, E1000_CR, reg | E1000_CR_RESET);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
if (IFM_SUBTYPE(ife->ifm_media) == IFM_1000_T) {
gig |= E1000_1GCR_MS_ENABLE;
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
if ((ife->ifm_media & IFM_ETH_MASTER) != 0)
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
gig |= E1000_1GCR_MS_VALUE;
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
} else if ((sc->mii_flags & MIIF_HAVE_GTCR) != 0)
- Masking IFM_GMASK when also masking IFM_FDX is redundant and just complicates the code. - Don't let atphy_setmedia() announce PAUSE support for half-duplex when MIIF_FORCEPAUSE is set. - Simplify e1000phy_service() and ip1000phy_service() to only set the manual configuration bits once after we have figured them all out. For ip1000phy_service() this also means we no longer unnecessarily update the hardware along the road. MFC after: 1 week
2011-01-14 19:16:59 +00:00
gig = 0;
PHY_WRITE(sc, E1000_1GCR, gig);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
PHY_WRITE(sc, E1000_AR, E1000_AR_SELECTOR_FIELD);
PHY_WRITE(sc, E1000_CR, speed | E1000_CR_RESET);
done:
break;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
case MII_TICK:
/*
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
* Only used for autonegotiation.
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
*/
Reset autonegotation timer if media option is not IFM_AUTO. Make mii_ticks advance, autonegiation is retried every mii_anegticks seconds.
2007-11-16 10:39:18 +00:00
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO) {
sc->mii_ticks = 0;
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
break;
Reset autonegotation timer if media option is not IFM_AUTO. Make mii_ticks advance, autonegiation is retried every mii_anegticks seconds.
2007-11-16 10:39:18 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
/*
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
* check for link.
* Read the status register twice; BMSR_LINK is latch-low.
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
*/
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
reg = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
if (reg & BMSR_LINK) {
sc->mii_ticks = 0;
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
/* Announce link loss right after it happens. */
Reset autonegotation timer if media option is not IFM_AUTO. Make mii_ticks advance, autonegiation is retried every mii_anegticks seconds.
2007-11-16 10:39:18 +00:00
if (sc->mii_ticks++ == 0)
break;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
if (sc->mii_ticks <= sc->mii_anegticks)
Report current link state while auto-negotiation is in progress.
2009-05-25 01:45:28 +00:00
break;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
sc->mii_ticks = 0;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_RESET(sc);
e1000phy_mii_phy_auto(sc, ife->ifm_media);
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
break;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
/* Update the media status. */
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_STATUS(sc);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
/* Callback if something changed. */
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
mii_phy_update(sc, cmd);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
return (0);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static void
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
e1000phy_status(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
int bmcr, bmsr, ssr;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
bmsr = PHY_READ(sc, E1000_SR) | PHY_READ(sc, E1000_SR);
bmcr = PHY_READ(sc, E1000_CR);
ssr = PHY_READ(sc, E1000_SSR);
if (bmsr & E1000_SR_LINK_STATUS)
mii->mii_media_status |= IFM_ACTIVE;
if (bmcr & E1000_CR_LOOPBACK)
mii->mii_media_active |= IFM_LOOP;
Don't read unnecessary PHY registers. Speed/duplex resolution bit is valid only for auto-negotiation case so check the bit if we know auto-negotiation is active. While I'm here explicitly checks current speed with speed mask and set IFM_NONE if resolved speed is unknown.
2009-05-25 01:56:19 +00:00
if ((bmcr & E1000_CR_AUTO_NEG_ENABLE) != 0 &&
(ssr & E1000_SSR_SPD_DPLX_RESOLVED) == 0) {
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
/* Erg, still trying, I guess... */
mii->mii_media_active |= IFM_NONE;
return;
}
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
if ((sc->mii_flags & MIIF_HAVEFIBER) == 0) {
Don't read unnecessary PHY registers. Speed/duplex resolution bit is valid only for auto-negotiation case so check the bit if we know auto-negotiation is active. While I'm here explicitly checks current speed with speed mask and set IFM_NONE if resolved speed is unknown.
2009-05-25 01:56:19 +00:00
switch (ssr & E1000_SSR_SPEED) {
case E1000_SSR_1000MBS:
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
mii->mii_media_active |= IFM_1000_T;
Don't read unnecessary PHY registers. Speed/duplex resolution bit is valid only for auto-negotiation case so check the bit if we know auto-negotiation is active. While I'm here explicitly checks current speed with speed mask and set IFM_NONE if resolved speed is unknown.
2009-05-25 01:56:19 +00:00
break;
case E1000_SSR_100MBS:
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
mii->mii_media_active |= IFM_100_TX;
Don't read unnecessary PHY registers. Speed/duplex resolution bit is valid only for auto-negotiation case so check the bit if we know auto-negotiation is active. While I'm here explicitly checks current speed with speed mask and set IFM_NONE if resolved speed is unknown.
2009-05-25 01:56:19 +00:00
break;
case E1000_SSR_10MBS:
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
mii->mii_media_active |= IFM_10_T;
Don't read unnecessary PHY registers. Speed/duplex resolution bit is valid only for auto-negotiation case so check the bit if we know auto-negotiation is active. While I'm here explicitly checks current speed with speed mask and set IFM_NONE if resolved speed is unknown.
2009-05-25 01:56:19 +00:00
break;
default:
mii->mii_media_active |= IFM_NONE;
return;
}
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
} else {
Some fiber PHY(88E1112) does not seem to set resolved speed so always assume we've got IFM_1000_SX.
2009-09-28 19:53:53 +00:00
/*
* Some fiber PHY(88E1112) does not seem to set resolved
* speed so always assume we've got IFM_1000_SX.
*/
mii->mii_media_active |= IFM_1000_SX;
Add support for SK-9521 V2.0 and 3COM 3C940. Tested at 100Mbit only, using Asus P4P800 onboard 3C940. The -stable version of this patch I have in use for ~2 weeks now, and works just fine for me. Based on: Nathan L. Binkert's patch for OpenBSD Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com> MFC after: 2 weeks
2003-09-20 10:53:08 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
if (ssr & E1000_SSR_DUPLEX) {
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
mii->mii_media_active |= IFM_FDX;
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
if ((sc->mii_flags & MIIF_HAVEFIBER) == 0)
mii->mii_media_active |= mii_phy_flowstatus(sc);
} else
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
mii->mii_media_active |= IFM_HDX;
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
if (IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T) {
if (((PHY_READ(sc, E1000_1GSR) | PHY_READ(sc, E1000_1GSR)) &
E1000_1GSR_MS_CONFIG_RES) != 0)
mii->mii_media_active |= IFM_ETH_MASTER;
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
}
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
}
static int
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
e1000phy_mii_phy_auto(struct mii_softc *sc, int media)
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
{
Do not ignore NEXT Page capability of auto-negotiation advertisement register. Some PHYs such as 88E3016 requires NEXT Page capability to establish valid link. Also set protocol selector field which is read only but it makes the intention clearer.
2009-05-25 02:05:00 +00:00
uint16_t reg;
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
Do not ignore NEXT Page capability of auto-negotiation advertisement register. Some PHYs such as 88E3016 requires NEXT Page capability to establish valid link. Also set protocol selector field which is read only but it makes the intention clearer.
2009-05-25 02:05:00 +00:00
if ((sc->mii_flags & MIIF_HAVEFIBER) == 0) {
reg = PHY_READ(sc, E1000_AR);
Allow pause support advertisement to be turned off again. Submitted by: yongari (ip1000phy(4))
2010-11-27 01:26:59 +00:00
reg &= ~(E1000_AR_PAUSE | E1000_AR_ASM_DIR);
Do not ignore NEXT Page capability of auto-negotiation advertisement register. Some PHYs such as 88E3016 requires NEXT Page capability to establish valid link. Also set protocol selector field which is read only but it makes the intention clearer.
2009-05-25 02:05:00 +00:00
reg |= E1000_AR_10T | E1000_AR_10T_FD |
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
E1000_AR_100TX | E1000_AR_100TX_FD;
if ((media & IFM_FLOW) != 0 ||
(sc->mii_flags & MIIF_FORCEPAUSE) != 0)
reg |= E1000_AR_PAUSE | E1000_AR_ASM_DIR;
Do not ignore NEXT Page capability of auto-negotiation advertisement register. Some PHYs such as 88E3016 requires NEXT Page capability to establish valid link. Also set protocol selector field which is read only but it makes the intention clearer.
2009-05-25 02:05:00 +00:00
PHY_WRITE(sc, E1000_AR, reg | E1000_AR_SELECTOR_FIELD);
} else
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control support in mii(4): - Merge generic flow control advertisement (which can be enabled by passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD, IFM_FLOW isn't implemented as a global option via the "don't care mask" but instead as a media specific option this. This has the following advantages: o allows flow control advertisement with autonegotiation to be turned on and off via ifconfig(8) with the default typically being off (though MIIF_FORCEPAUSE has been added causing flow control to be always advertised, allowing to easily MFC this changes for drivers that previously used home-grown support for flow control that behaved that way without breaking POLA) o allows to deal with PHY drivers where flow control advertisement with manual selection doesn't work or at least isn't implemented, like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4), by setting MIIF_NOMANPAUSE o the available combinations of media options are readily available from the `ifconfig -m` output - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so these are understood by ifconfig(8). o Make the master/slave support in mii(4) actually usable: - Change IFM_ETH_MASTER from being implemented as a global option via the "don't care mask" to a media specific one as it actually is only applicable to IFM_1000_T to date. - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to actually configure manually selected slave mode (like we also do in the PHY specific implementations). - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it is understood by ifconfig(8). o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4), e1000phy(4) and ip1000phy(4) to use the generic flow control support instead of home-grown solutions via IFM_FLAGs. This includes changing these PHY drivers and smcphy(4) to no longer unconditionally advertise support for flow control but only if the selected media has IFM_FLOW set (or MIIF_FORCEPAUSE is set) and implemented for these media variants, i.e. typically only for copper. o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0 and some IFM_FLAGn. o Switch brgphy(4) to add at least the the supported copper media based on the contents of the BMSR via mii_phy_add_media() instead of hardcoding them. The latter approach seems to have developed historically, besides causing unnecessary code duplication it was also undesirable because brgphy_mii_phy_auto() already based the capability advertisement on the contents of the BMSR though. o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not just BCM5701. Apparently this was a misinterpretation of a workaround in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but this doesn't mean we can't set these as well on other PHYs for manual media selection. o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so IFM_1000_T master mode support now is generally available with all PHY drivers. o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's not applicable there. Reviewed by: yongari (plus additional testing) Obtained from: NetBSD (partially), OpenBSD (partially) MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
PHY_WRITE(sc, E1000_AR, E1000_FA_1000X_FD | E1000_FA_1000X);
Do not blindly announce 1000baseT half-duplex capability in autonegotiation. Some controllers like cgem(4) do not support half-duplex at gigabit speeds.
2014-09-04 01:04:37 +00:00
if ((sc->mii_flags & MIIF_HAVE_GTCR) != 0) {
reg = 0;
if ((sc->mii_extcapabilities & EXTSR_1000TFDX) != 0)
reg |= E1000_1GCR_1000T_FD;
if ((sc->mii_extcapabilities & EXTSR_1000THDX) != 0)
reg |= E1000_1GCR_1000T;
PHY_WRITE(sc, E1000_1GCR, reg);
}
o Add support code for newer Marvell PHYs. o Remove unused static global variable e1000phy_debug. o Take advantage of mii_phy_dev_probe(). o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5. o Add IFM_NONE as e1000phy(4) supports it without issues. o Nuke magic PHY programming sequence in PHY reset and follow correct reset sequence. [1] o Make manual media selection work for all supported media types. o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in configurations with multiple PHYs. o In 1000baseT, when setting the link manually, one side must be the master and the other the slave. If LINK0 is set, program the PHY to be a master, otherwise it's a slave. o When we lost a link, reset mii_ticks immediately so it correctly check number of seconds elapsed in autonegotiation phase. o Announce link loss right after it happens. o After kicking autonegotiation, report PHY status instead of returning immediatly. o When link state check is in progress, check auto negotiation completion bit only when auto negotiation is enbaled. o When PHY is resolved to a master, show it with IFM_FLAG2. Special thanks to marius who fixed several nits in original patch. In half-duplex mode, nfe(4) fails to send packets. I think it's a bug in nfe(4) as the same PHY works without problems on msk(4). Obtained from: em(4) [1] Reviewed by: marius Tested by: bz
2006-12-11 11:09:48 +00:00
PHY_WRITE(sc, E1000_CR,
E1000_CR_AUTO_NEG_ENABLE | E1000_CR_RESTART_AUTO_NEG);
Add Marvell PHY support for 10/100/1000 LIVENGOOD_CU Intel NIC. Parag Patel did all of the grunt work, so he gets the credit. Register definitions and actions inferred from a Linux driver, so Intel also gets some 'credit'.
2001-04-09 21:29:44 +00:00
return (EJUSTRETURN);
}
Reference in New Issue Copy Permalink