d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
1f70d62298
freebsd-skq/sys/amd64/include/apicvar.h

181 lines
6.6 KiB
C
Raw Normal View History

New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
/*-
* Copyright (c) 2003 John Baldwin <jhb@FreeBSD.org>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _MACHINE_APICVAR_H_
#define _MACHINE_APICVAR_H_
Initial landing of SMP support for FreeBSD/amd64. - This is heavily derived from John Baldwin's apic/pci cleanup on i386. - I have completely rewritten or drastically cleaned up some other parts. (in particular, bootstrap) - This is still a WIP. It seems that there are some highly bogus bioses on nVidia nForce3-150 boards. I can't stress how broken these boards are. I have a workaround in mind, but right now the Asus SK8N is broken. The Gigabyte K8NPro (nVidia based) is also mind-numbingly hosed. - Most of my testing has been with SCHED_ULE. SCHED_4BSD works. - the apic and acpi components are 'standard'. - If you have an nVidia nForce3-150 board, you are stuck with 'device atpic' in addition, because they somehow managed to forget to connect the 8254 timer to the apic, even though its in the same silicon! ARGH! This directly violates the ACPI spec.
2003-11-17 08:58:16 +00:00
#include <machine/segments.h>
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
/*
* Local && I/O APIC variable definitions.
*/
/*
* Layout of local APIC interrupt vectors:
*
* 0xff (255) +-------------+
Whitespace nit (sorry, couldn't help it)
2003-11-14 22:21:30 +00:00
* | | 15 (Spurious / IPIs / Local Interrupts)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
* 0xf0 (240) +-------------+
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
* | | 14 (I/O Interrupts)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
* 0xe0 (224) +-------------+
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
* | | 13 (I/O Interrupts)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
* 0xd0 (208) +-------------+
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
* | | 12 (I/O Interrupts)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
* 0xc0 (192) +-------------+
* | | 11 (I/O Interrupts)
* 0xb0 (176) +-------------+
* | | 10 (I/O Interrupts)
* 0xa0 (160) +-------------+
* | | 9 (I/O Interrupts)
* 0x90 (144) +-------------+
* | | 8 (I/O Interrupts / System Calls)
* 0x80 (128) +-------------+
* | | 7 (I/O Interrupts)
* 0x70 (112) +-------------+
* | | 6 (I/O Interrupts)
* 0x60 (96) +-------------+
* | | 5 (I/O Interrupts)
* 0x50 (80) +-------------+
* | | 4 (I/O Interrupts)
* 0x40 (64) +-------------+
* | | 3 (I/O Interrupts)
* 0x30 (48) +-------------+
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
* | | 2 (ATPIC Interrupts)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
* 0x20 (32) +-------------+
* | | 1 (Exceptions, traps, faults, etc.)
* 0x10 (16) +-------------+
* | | 0 (Exceptions, traps, faults, etc.)
* 0x00 (0) +-------------+
*
* Note: 0x80 needs to be handled specially and not allocated to an
* I/O device!
*/
#define APIC_ID_ALL 0xff
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
#define APIC_IO_INTS (IDT_IO_INTS + 16)
#define APIC_NUM_IOINTS 192
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
#define APIC_LOCAL_INTS 240
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
#define APIC_TIMER_INT APIC_LOCAL_INTS
#define APIC_ERROR_INT (APIC_LOCAL_INTS + 1)
#define APIC_THERMAL_INT (APIC_LOCAL_INTS + 2)
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
#define APIC_IPI_INTS (APIC_LOCAL_INTS + 3)
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
#define IPI_AST APIC_IPI_INTS /* Generate software trap. */
#define IPI_INVLTLB (APIC_IPI_INTS + 1) /* TLB Shootdown IPIs */
#define IPI_INVLPG (APIC_IPI_INTS + 2)
#define IPI_INVLRNG (APIC_IPI_INTS + 3)
#define IPI_HARDCLOCK (APIC_IPI_INTS + 8) /* Inter-CPU clock handling. */
#define IPI_STATCLOCK (APIC_IPI_INTS + 9)
#define IPI_RENDEZVOUS (APIC_IPI_INTS + 10) /* Inter-CPU rendezvous. */
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
#define IPI_STOP (APIC_IPI_INTS + 11) /* Stop CPU until restarted. */
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
#define APIC_SPURIOUS_INT 255
#define LVT_LINT0 0
#define LVT_LINT1 1
#define LVT_TIMER 2
#define LVT_ERROR 3
#define LVT_PMC 4
#define LVT_THERMAL 5
#define LVT_MAX LVT_THERMAL
#ifndef LOCORE
#define APIC_IPI_DEST_SELF -1
#define APIC_IPI_DEST_ALL -2
#define APIC_IPI_DEST_OTHERS -3
MFi386: various io apic cleanups
2004-07-08 01:42:49 +00:00
#define APIC_BUS_UNKNOWN -1
#define APIC_BUS_ISA 0
#define APIC_BUS_EISA 1
#define APIC_BUS_PCI 2
#define APIC_BUS_MAX APIC_BUS_PCI
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
/*
* An APIC enumerator is a psuedo bus driver that enumerates APIC's including
* CPU's and I/O APIC's.
*/
struct apic_enumerator {
const char *apic_name;
int (*apic_probe)(void);
int (*apic_probe_cpus)(void);
int (*apic_setup_local)(void);
int (*apic_setup_io)(void);
SLIST_ENTRY(apic_enumerator) apic_next;
};
inthand_t
IDTVEC(apic_isr1), IDTVEC(apic_isr2), IDTVEC(apic_isr3),
Shuffle the APIC interrupt vectors around a bit: - Move the IPI and local APIC interrupt vectors up into the 0xf0 - 0xff range. The pmap lazyfix IPI was reordered down next to the TLB shootdowns to avoid conflicting with the spurious interrupt vector. - Move the base of APIC interrupts up 16 so that the first 16 APIC interrupts do not overlap the vectors used by the ATPIC. - Remove bogus interrupt vector reservations for LINT[01]. - Now that 0xc0 - 0xef are available, use them for device interrupts. This increases the number of APIC device interrupts to 191. - Increase the system-wide number of global interrupts to 191 to catch up to more APIC interrupts. Requested by: peter (2)
2003-11-14 19:10:13 +00:00
IDTVEC(apic_isr4), IDTVEC(apic_isr5), IDTVEC(apic_isr6),
IDTVEC(apic_isr7), IDTVEC(spuriousint);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
u_int apic_irq_to_idt(u_int irq);
u_int apic_idt_to_irq(u_int vector);
void apic_register_enumerator(struct apic_enumerator *enumerator);
void *ioapic_create(uintptr_t addr, int32_t id, int intbase);
int ioapic_disable_pin(void *cookie, u_int pin);
MFi386: numerous interrupt and acpi updates
2004-05-16 20:30:47 +00:00
void ioapic_enable_mixed_mode(void);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
int ioapic_get_vector(void *cookie, u_int pin);
int ioapic_next_logical_cluster(void);
void ioapic_register(void *cookie);
int ioapic_remap_vector(void *cookie, u_int pin, int vector);
MFi386: various io apic cleanups
2004-07-08 01:42:49 +00:00
int ioapic_set_bus(void *cookie, u_int pin, int bus_type);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
int ioapic_set_extint(void *cookie, u_int pin);
int ioapic_set_nmi(void *cookie, u_int pin);
MFi386: numerous interrupt and acpi updates
2004-05-16 20:30:47 +00:00
int ioapic_set_polarity(void *cookie, u_int pin, enum intr_polarity pol);
int ioapic_set_triggermode(void *cookie, u_int pin,
enum intr_trigger trigger);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
int ioapic_set_smi(void *cookie, u_int pin);
void lapic_create(u_int apic_id, int boot_cpu);
void lapic_disable(void);
void lapic_dump(const char *str);
void lapic_enable_intr(u_int vector);
- Move manipulation of td_intr_nesting_level out of assembly interrupt vector stubs and into the C functions they call. - Move disabling and EOIing of interrupt sources out of PIC driver entry points and into intr_execute_handlers(). Intr_execute_handlers() only disables a source for an interrupt if it is a stray interrupt or has threaded handlers. Sources with fast handlers no longer disable (mask) the source while executing the handlers. - Move the setting of clkintr_pending into intr_execute_handlers() and set the variable for any interrupt source with a vector of 0. (Should only be true for IRQ 0.) This fixes clkintr_pending in the NO_MIXED_MODE case. - Implement lapic_eoi() and use it to implement ioapic_eoi_source(). - Rename atpic_sched_ithd() to atpic_handle_intr() since it is used to handle all atpic interrupts and not just threaded ones. Inspired by: peter's changes to amd64 in p4 (1) Requested by: bde (2)
2003-11-12 18:13:57 +00:00
void lapic_eoi(void);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
int lapic_id(void);
void lapic_init(uintptr_t addr);
int lapic_intr_pending(u_int vector);
void lapic_ipi_raw(register_t icrlo, u_int dest);
void lapic_ipi_vectored(u_int vector, int dest);
int lapic_ipi_wait(int delay);
Initial landing of SMP support for FreeBSD/amd64. - This is heavily derived from John Baldwin's apic/pci cleanup on i386. - I have completely rewritten or drastically cleaned up some other parts. (in particular, bootstrap) - This is still a WIP. It seems that there are some highly bogus bioses on nVidia nForce3-150 boards. I can't stress how broken these boards are. I have a workaround in mind, but right now the Asus SK8N is broken. The Gigabyte K8NPro (nVidia based) is also mind-numbingly hosed. - Most of my testing has been with SCHED_ULE. SCHED_4BSD works. - the apic and acpi components are 'standard'. - If you have an nVidia nForce3-150 board, you are stuck with 'device atpic' in addition, because they somehow managed to forget to connect the 8254 timer to the apic, even though its in the same silicon! ARGH! This directly violates the ACPI spec.
2003-11-17 08:58:16 +00:00
void lapic_handle_intr(void *cookie, struct intrframe frame);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
void lapic_set_logical_id(u_int apic_id, u_int cluster, u_int cluster_id);
int lapic_set_lvt_mask(u_int apic_id, u_int lvt, u_char masked);
int lapic_set_lvt_mode(u_int apic_id, u_int lvt, u_int32_t mode);
MFi386: numerous interrupt and acpi updates
2004-05-16 20:30:47 +00:00
int lapic_set_lvt_polarity(u_int apic_id, u_int lvt,
enum intr_polarity pol);
int lapic_set_lvt_triggermode(u_int apic_id, u_int lvt,
enum intr_trigger trigger);
New APIC support code: - The apic interrupt entry points have been rewritten so that each entry point can serve 32 different vectors. When the entry is executed, it uses one of the 32-bit ISR registers to determine which vector in its assigned range was triggered. Thus, the apic code can support 159 different interrupt vectors with only 5 entry points. - We now always to disable the local APIC to work around an errata in certain PPros and then re-enable it again if we decide to use the APICs to route interrupts. - We no longer map IO APICs or local APICs using special page table entries. Instead, we just use pmap_mapdev(). We also no longer export the virtual address of the local APIC as a global symbol to the rest of the system, but only in local_apic.c. To aid this, the APIC ID of each CPU is exported as a per-CPU variable. - Interrupt sources are provided for each intpin on each IO APIC. Currently, each source is given a unique interrupt vector meaning that PCI interrupts are not shared on most machines with an I/O APIC. That mapping for interrupt sources to interrupt vectors is up to the APIC enumerator driver however. - We no longer probe to see if we need to use mixed mode to route IRQ 0, instead we always use mixed mode to route IRQ 0 for now. This can be disabled via the 'NO_MIXED_MODE' kernel option. - The npx(4) driver now always probes to see if a built-in FPU is present since this test can now be performed with the new APIC code. However, an SMP kernel will panic if there is more than one CPU and a built-in FPU is not found. - PCI interrupts are now properly routed when using APICs to route interrupts, so remove the hack to psuedo-route interrupts when the intpin register was read. - The apic.h header was moved to apicreg.h and a new apicvar.h header that declares the APIs used by the new APIC code was added.
2003-11-03 21:53:38 +00:00
void lapic_setup(void);
#endif /* !LOCORE */
#endif /* _MACHINE_APICVAR_H_ */
Reference in New Issue Copy Permalink