d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
22dbb8bf5e
freebsd-skq/sys/mips/include/reg.h

110 lines
3.3 KiB
C
Raw Normal View History

FreeBSD/mips port. The FreeBSD/mips port targets mips32, mips64, mips32r2 and mips64r2 (and close relatives) processors. There presently is support for ADMtek ADM5120, A mips 4Kc in a malta board, the RB533 routerboard (based on IDT RC32434) and some preliminary support for sibtye/broadcom designs. Other hardware support will be forthcomcing. This port boots multiuser under gxemul emulating the malta board and also bootstraps on the hardware whose support is forthcoming... Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard, Randall Stewert and others that have contributed to the mips2 and/or mips2-jnpr perforce branches. Juniper contirbuted a generic mips port late in the life cycle of the misp2 branch. Warner Losh merged the mips2 and Juniper code bases, and others list above have worked for the past several months to get to multiuser. In addition, the mips2 work owe a debt to the trail blazing efforts of the original mips branch in perforce done by Juli Mallett.
2008-04-13 07:27:37 +00:00
/* $OpenBSD: reg.h,v 1.1 1998/01/28 11:14:53 pefo Exp $ */
/*-
sys: further adoption of SPDX licensing ID tags. Mainly focus on files that use BSD 3-Clause license. The Software Package Data Exchange (SPDX) group provides a specification to make it easier for automated tools to detect and summarize well known opensource licenses. We are gradually adopting the specification, noting that the tags are considered only advisory and do not, in any way, superceed or replace the license texts. Special thanks to Wind River for providing access to "The Duke of Highlander" tool: an older (2014) run over FreeBSD tree was useful as a starting point.
2017-11-20 19:43:44 +00:00
* SPDX-License-Identifier: BSD-3-Clause
*
FreeBSD/mips port. The FreeBSD/mips port targets mips32, mips64, mips32r2 and mips64r2 (and close relatives) processors. There presently is support for ADMtek ADM5120, A mips 4Kc in a malta board, the RB533 routerboard (based on IDT RC32434) and some preliminary support for sibtye/broadcom designs. Other hardware support will be forthcomcing. This port boots multiuser under gxemul emulating the malta board and also bootstraps on the hardware whose support is forthcoming... Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard, Randall Stewert and others that have contributed to the mips2 and/or mips2-jnpr perforce branches. Juniper contirbuted a generic mips port late in the life cycle of the misp2 branch. Warner Losh merged the mips2 and Juniper code bases, and others list above have worked for the past several months to get to multiuser. In addition, the mips2 work owe a debt to the trail blazing efforts of the original mips branch in perforce done by Juli Mallett.
2008-04-13 07:27:37 +00:00
* Copyright (c) 1988 University of Utah.
* Copyright (c) 1992, 1993
* The Regents of the University of California. All rights reserved.
*
* This code is derived from software contributed to Berkeley by
* the Systems Programming Group of the University of Utah Computer
* Science Department and Ralph Campbell.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
Renumber copyright clause 4 Renumber cluase 4 to 3, per what everybody else did when BSD granted them permission to remove clause 3. My insistance on keeping the same numbering for legal reasons is too pedantic, so give up on that point. Submitted by: Jan Schaumann <jschauma@stevens.edu> Pull Request: https://github.com/freebsd/freebsd/pull/96
2017-02-28 23:42:47 +00:00
* 3. Neither the name of the University nor the names of its contributors
FreeBSD/mips port. The FreeBSD/mips port targets mips32, mips64, mips32r2 and mips64r2 (and close relatives) processors. There presently is support for ADMtek ADM5120, A mips 4Kc in a malta board, the RB533 routerboard (based on IDT RC32434) and some preliminary support for sibtye/broadcom designs. Other hardware support will be forthcomcing. This port boots multiuser under gxemul emulating the malta board and also bootstraps on the hardware whose support is forthcoming... Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard, Randall Stewert and others that have contributed to the mips2 and/or mips2-jnpr perforce branches. Juniper contirbuted a generic mips port late in the life cycle of the misp2 branch. Warner Losh merged the mips2 and Juniper code bases, and others list above have worked for the past several months to get to multiuser. In addition, the mips2 work owe a debt to the trail blazing efforts of the original mips branch in perforce done by Juli Mallett.
2008-04-13 07:27:37 +00:00
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* from: Utah Hdr: reg.h 1.1 90/07/09
* @(#)reg.h 8.2 (Berkeley) 1/11/94
* JNPR: reg.h,v 1.6 2006/09/15 12:52:34 katta
* $FreeBSD$
*/
#ifndef _MACHINE_REG_H_
#define _MACHINE_REG_H_
/*
* Location of the users' stored registers relative to ZERO.
* must be visible to assembly code.
*/
#include <machine/regnum.h>
/*
* Register set accessible via /proc/$pid/reg
*/
struct reg {
register_t r_regs[NUMSAVEREGS]; /* numbered as above */
};
struct fpreg {
f_register_t r_regs[NUMFPREGS];
};
/*
* Placeholder.
*/
struct dbreg {
unsigned long junk;
};
Move the 32-bit compatible procfs types from freebsd32.h to <sys/procfs.h> and export them to userland. - Define __HAVE_REG32 on platforms that define a reg32 structure and check for this in <sys/procfs.h> to control when to export prstatus32, etc. - Add prstatus32_t and prpsinfo32_t typedefs for the 32-bit structures. libbfd looks for these types, and having them fixes 'gcore' in gdb of a 32-bit process on a 64-bit platform. - Use the structure definitions from <sys/procfs.h> in gcore's elf32 core dump code instead of duplicating the definitions. Differential Revision: https://reviews.freebsd.org/D2142 Reviewed by: kib, nathanw (powerpc bits) MFC after: 1 week
2015-04-08 16:30:45 +00:00
#ifdef __LP64__
o) Add COMPAT_FREEBSD32 support for MIPS kernels using the n64 ABI with userlands using the o32 ABI. This mostly follows nwhitehorn's lead in implementing COMPAT_FREEBSD32 on powerpc64. o) Add a new type to the freebsd32 compat layer, time32_t, which is time_t in the 32-bit ABI being used. Since the MIPS port is relatively-new, even the 32-bit ABIs use a 64-bit time_t. o) Because time{spec,val}32 has the same size and layout as time{spec,val} on MIPS with 32-bit compatibility, then, disable some code which assumes otherwise wrongly when built for MIPS. A more general macro to check in this case would seem like a good idea eventually. If someone adds support for using n32 userland with n64 kernels on MIPS, then they will have to add a variety of flags related to each piece of the ABI that can vary. That's probably the right time to generalize further. o) Add MIPS to the list of architectures which use PAD64_REQUIRED in the freebsd32 compat code. Probably this should be generalized at some point. Reviewed by: gonzo
2012-03-03 08:19:18 +00:00
/* Must match struct trapframe */
struct reg32 {
uint32_t r_regs[NUMSAVEREGS];
};
struct fpreg32 {
int32_t r_regs[NUMFPREGS];
};
struct dbreg32 {
uint32_t junk;
};
Move the 32-bit compatible procfs types from freebsd32.h to <sys/procfs.h> and export them to userland. - Define __HAVE_REG32 on platforms that define a reg32 structure and check for this in <sys/procfs.h> to control when to export prstatus32, etc. - Add prstatus32_t and prpsinfo32_t typedefs for the 32-bit structures. libbfd looks for these types, and having them fixes 'gcore' in gdb of a 32-bit process on a 64-bit platform. - Use the structure definitions from <sys/procfs.h> in gcore's elf32 core dump code instead of duplicating the definitions. Differential Revision: https://reviews.freebsd.org/D2142 Reviewed by: kib, nathanw (powerpc bits) MFC after: 1 week
2015-04-08 16:30:45 +00:00
#define __HAVE_REG32
o) Add COMPAT_FREEBSD32 support for MIPS kernels using the n64 ABI with userlands using the o32 ABI. This mostly follows nwhitehorn's lead in implementing COMPAT_FREEBSD32 on powerpc64. o) Add a new type to the freebsd32 compat layer, time32_t, which is time_t in the 32-bit ABI being used. Since the MIPS port is relatively-new, even the 32-bit ABIs use a 64-bit time_t. o) Because time{spec,val}32 has the same size and layout as time{spec,val} on MIPS with 32-bit compatibility, then, disable some code which assumes otherwise wrongly when built for MIPS. A more general macro to check in this case would seem like a good idea eventually. If someone adds support for using n32 userland with n64 kernels on MIPS, then they will have to add a variety of flags related to each piece of the ABI that can vary. That's probably the right time to generalize further. o) Add MIPS to the list of architectures which use PAD64_REQUIRED in the freebsd32 compat code. Probably this should be generalized at some point. Reviewed by: gonzo
2012-03-03 08:19:18 +00:00
#endif
FreeBSD/mips port. The FreeBSD/mips port targets mips32, mips64, mips32r2 and mips64r2 (and close relatives) processors. There presently is support for ADMtek ADM5120, A mips 4Kc in a malta board, the RB533 routerboard (based on IDT RC32434) and some preliminary support for sibtye/broadcom designs. Other hardware support will be forthcomcing. This port boots multiuser under gxemul emulating the malta board and also bootstraps on the hardware whose support is forthcoming... Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard, Randall Stewert and others that have contributed to the mips2 and/or mips2-jnpr perforce branches. Juniper contirbuted a generic mips port late in the life cycle of the misp2 branch. Warner Losh merged the mips2 and Juniper code bases, and others list above have worked for the past several months to get to multiuser. In addition, the mips2 work owe a debt to the trail blazing efforts of the original mips branch in perforce done by Juli Mallett.
2008-04-13 07:27:37 +00:00
#ifdef _KERNEL
int fill_fpregs(struct thread *, struct fpreg *);
int fill_regs(struct thread *, struct reg *);
int set_fpregs(struct thread *, struct fpreg *);
int set_regs(struct thread *, struct reg *);
int fill_dbregs(struct thread *, struct dbreg *);
int set_dbregs(struct thread *, struct dbreg *);
#endif
o) Add COMPAT_FREEBSD32 support for MIPS kernels using the n64 ABI with userlands using the o32 ABI. This mostly follows nwhitehorn's lead in implementing COMPAT_FREEBSD32 on powerpc64. o) Add a new type to the freebsd32 compat layer, time32_t, which is time_t in the 32-bit ABI being used. Since the MIPS port is relatively-new, even the 32-bit ABIs use a 64-bit time_t. o) Because time{spec,val}32 has the same size and layout as time{spec,val} on MIPS with 32-bit compatibility, then, disable some code which assumes otherwise wrongly when built for MIPS. A more general macro to check in this case would seem like a good idea eventually. If someone adds support for using n32 userland with n64 kernels on MIPS, then they will have to add a variety of flags related to each piece of the ABI that can vary. That's probably the right time to generalize further. o) Add MIPS to the list of architectures which use PAD64_REQUIRED in the freebsd32 compat code. Probably this should be generalized at some point. Reviewed by: gonzo
2012-03-03 08:19:18 +00:00
#ifdef COMPAT_FREEBSD32
struct image_params;
int fill_regs32(struct thread *, struct reg32 *);
int set_regs32(struct thread *, struct reg32 *);
int fill_fpregs32(struct thread *, struct fpreg32 *);
int set_fpregs32(struct thread *, struct fpreg32 *);
#define fill_dbregs32(td, reg) 0
#define set_dbregs32(td, reg) 0
#endif
FreeBSD/mips port. The FreeBSD/mips port targets mips32, mips64, mips32r2 and mips64r2 (and close relatives) processors. There presently is support for ADMtek ADM5120, A mips 4Kc in a malta board, the RB533 routerboard (based on IDT RC32434) and some preliminary support for sibtye/broadcom designs. Other hardware support will be forthcomcing. This port boots multiuser under gxemul emulating the malta board and also bootstraps on the hardware whose support is forthcoming... Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard, Randall Stewert and others that have contributed to the mips2 and/or mips2-jnpr perforce branches. Juniper contirbuted a generic mips port late in the life cycle of the misp2 branch. Warner Losh merged the mips2 and Juniper code bases, and others list above have worked for the past several months to get to multiuser. In addition, the mips2 work owe a debt to the trail blazing efforts of the original mips branch in perforce done by Juli Mallett.
2008-04-13 07:27:37 +00:00
#endif /* !_MACHINE_REG_H_ */
Reference in New Issue Copy Permalink