freebsd-skq/usr.sbin/ppp/ppp.8.m4

.\" manual page [] for ppp 0.94 beta2 + alpha
.\" $Id: ppp.8,v 1.26 1997/03/13 21:39:41 brian Exp $
.Dd 20 September 1995
.Os FreeBSD
.Dt PPP 8
.Sh NAME
.Nm ppp
.Nd
Point to Point Protocol (aka iijppp) 
.Sh SYNOPSIS
.Nm
.Op Fl auto | background | ddial | direct | dedicated 
.Op Fl alias
.Op Ar system
.Sh DESCRIPTION
This is a user process
.Em PPP
software package.  Normally,
.Em PPP
is implemented as a part of the kernel (e.g. as managed by pppd) and it's
thus somewhat hard to debug and/or modify its behavior.  However, in this
implementation
.Em PPP
is done as a user process with the help of the
tunnel device driver (tun).

.Sh Major Features

.Bl -diag
.It Provides interactive user interface.
Using its command mode, the user can
easily enter commands to establish the connection with the remote end, check
the status of connection and close the connection.  All functions can
also be optionally password protected for security.

.It Supports both manual and automatic dialing.
Interactive mode has a
.Dq term
command which enables you to talk to your modem directly.  When your
modem is connected to the remote peer and it starts to talk
.Em PPP
, the
.Em PPP
software detects it and switches to packet
mode automatically. Once you have determined the proper sequence for connecting
with the remote host, you can write a chat script to define the necessary
dialing and login procedure for later convenience.

.It Supports on-demand dialup capability.
By using auto mode,
.Nm
will act as a daemon and wait for a packet to be sent over the
.Em PPP
link.  When this happens, the daemon automatically dials and establishes the
connection.

In almost the same manner ddial mode (dedicated or demon dialing)
also automatically dials and establishes the connection.  However, it
differs in that it will dial the remote site any time it detects the
link is down, even if there are no packets to be sent.  This mode is
useful for full-time connections who worry less about line charges
and more about being connected full time.

.It Supports packet aliasing.
Packet aliasing, more commonly known as masquerading, allows computers
on a private, unregistered network to access the internet.  The
.Em PPP
host acts as a masquerading gateway.  IP addresses as well as TCP and
UDP port numbers are aliased for outgoing packets and de-aliased for
returning packets.

.It Supports background PPP connections.
In background mode, if
.Nm
successfully establishes the connection, it will become a daemon.
Otherwise, it will exit with an error.

.It Supports server-side PPP connections.
Can act as server which accepts incoming
.Em PPP
connections.

.It Supports PAP and CHAP authentication.

.It Supports Proxy Arp.
When
.Em PPP
is set up as server, you can also configure it to do proxy arp for your
connection.

.It Supports packet filtering.
User can define four kinds of filters:
.Em ifilter
for incoming packets,
.Em ofilter
for outgoing packets,
.Em dfilter
to define a dialing trigger packet and
.Em afilter
for keeping a connection alive with the trigger packet.

.It Tunnel driver supports bpf.
The user can use
.Xr tcpdump 1
to check the packet flow over the
.Em PPP
link.

.It Supports PPP over TCP capability.


.It Supports IETF draft Predictor-1 compression.
.Nm
supports not only VJ-compression but also Predictor-1 compression.
Normally, a modem has built-in compression (e.g. v42.bis) and the system
may receive higher data rates from it as a result of such compression.
While this is generally a good thing in most other situations, this
higher speed data imposes a penalty on the system by increasing the
number of serial interrupts the system has to process in talking to the
modem and also increases latency.  Unlike VJ-compression, Predictor-1
compression pre-compresses
.Em all
data flowing through the link, thus reducing overhead to a minimum.

.It Supports Microsofts IPCP extentions.
Name Server Addresses and NetBIOS Name Server Addresses can be negotiated
with clients using the Microsoft
.Em PPP
stack (ie. Win95, WinNT)

.It Runs under BSDI-1.1 and FreeBSD.

.El


Patches for NeXTSTEP 3.2 are also available on the net.

.Sh GETTING STARTED

When you first run
.Nm
you may need to deal with some initial configuration details.  First,
your kernel should include a tunnel device (the default in FreeBSD 2.0.5
and later). If it doesn't, you'll need to rebuild your kernel with the
following line in your kernel configuration file:

.Dl pseudo-device   tun             1

You should set the numeric field to the maximum number of
.Em PPP
connections you wish to support.

Second, check your
.Pa /dev
directory for the tunnel device entry
.Pa /dev/tun0.
If it doesn't exist, you can create it by running "MAKEDEV tun0"

.Sh MANUAL DIALING

%
.Nm
User Process PPP written by Toshiharu OHNO.

* If you set your hostname and password in
.Pa /etc/ppp/ppp.secret ,
you can't do
anything except run the quit and help commands *

ppp on "your hostname"> help
  passwd  : Password for security
  quit    : Quit the PPP program
  help    : Display this message

ppp on tama> pass <password>

* "on" will change to "ON" if you specify the correct password. *

ppp ON tama>

* You can now specify the device name, speed and parity
for your modem, and whether
CTS/RTS signalling should be used (CTS/RTS is used by default).
If your hardware does not provide CTS/RTS lines (as
may happen when you are connected directly to certain ppp-capable
terminal servers),
.Nm
will never send any output through the port; it
waits for a signal which never comes.
Thus, if you have a direct line and can't seem to make
a connection, try turning ctsrts off: *


ppp ON tama> set line /dev/cuaa0

ppp ON tama> set speed 38400

ppp ON tama> set parity even

ppp ON tama> set ctsrts on

ppp ON tama> show modem

* Modem related parameters are shown in here *

ppp ON tama>

* Use term command to talk with your modem *

ppp ON tama> term
 at
 OK
 atdt123456
 CONNECT

 login: ppp
 Password:

* PPP started in remote side.  When the peer start to talk PPP, the
program will detect it automatically and return to command mode. *

ppp ON tama>

.Nm PPP
ON tama>

* NOW, you are connected!  Note that
.Sq PPP
in the prompt has changed to capital letters to indicate this. *

PPP ON tama> show lcp

* You'll see LCP status *

PPP ON tama> show ipcp

* You'll see IPCP status.  At this point, your machine has a host route
to the peer. If you want to add a default route entry, then enter the
following command. *

PPP ON tama> add 0 0 HISADDR

* The string
.Sq HISADDR
represents the IP address of connected peer. *

PPP ON tama>

* Use network applications (i.e. ping, telnet, ftp) in other windows *

PPP ON tama> show log

* Gives you some logging messages *

PPP ON tama> close

* The connection is closed and modem will be disconnected. *

ppp ON tama> quit

%

.Sh AUTOMATIC DIALING

To use automatic dialing, you must prepare some Dial and Login chat scripts.
See the example definitions in
.Pa /etc/ppp/ppp.conf.sample
(the format of ppp.conf is pretty simple).

.Bl -bullet -compact
.It
Each line contains one command, label or comment.
.It
A line starting with a
.Sq #
character is treated as a comment line.
.It
A label name has to start in the first column and should be followed by
a colon (:).
.It
A command line must contain a space or tab in the first column.
.El

Once ppp.conf is ready, specify the destination label name when you
invoke
.Nm ppp .
Commands associated with the destination label are then
executed. Note that the commands associated with the
.Dq default
label are ALWAYS executed.

Once the connection is made, you'll find that the
.Nm ppp
portion of the prompt has changed to
.Nm PPP .

   % ppp pm2
   ...
   ppp ON tama> dial
   dial OK!
   login OK!
   PPP ON tama>

If the
.Pa /etc/ppp/ppp.linkup
file is available, its contents are executed
when the
.Em PPP
connection is established.  See the provided example which adds a
default route.  The string HISADDR represents the IP address of the
remote peer.

.Sh BACKGROUND DIALING

If you want to establish a connection using
.Nm ppp non-interactively (such as from a
.Xr crontab(5)
entry or an
.Xr at(1)
script) you should use the
.Fl background
option.  You must also specify the destination label in
.Pa /etc/ppp/ppp.conf
to use.

When
.Fl background
is specified,
.Nm
attempts to establish the connection.  If this attempt fails,
.Nm ppp
exits immediately with a non-zero exit code.

If it succeeds, then
.Nm ppp
becomes a daemon, and returns an exit status of zero to its caller.
The daemon exits automatically if the connection is dropped by the
remote system, or it receives a TERM signal.

The file
.Pa /var/run/ppp.tun0.pid
contains the process id number of the
.Nm ppp
program that is using the tunnel device tun0.

.Sh DIAL ON DEMAND

To play with demand dialing, you must use the
.Fl auto
or
.Fl ddial
option.  You must also specify the destination label in
.Pa /etc/ppp/ppp.conf
to use.  It should contain the
.Dq ifaddr
command to define the remote peer's IP address. (refer to
.Pa /etc/ppp/ppp.conf.sample )

   % ppp -auto pm2demand
   ...
   %

When
.Fl auto
or
.Fl ddial
is specified,
.Nm
runs as a daemon but you can still configure or examine its
configuration by using the diagnostic port as follows:


  % telnet localhost 3000
    Trying 127.0.0.1...
    Connected to localhost.spec.co.jp.
    Escape character is '^]'.
    User Process PPP. Written by Toshiharu OHNO.
    Working as auto mode.
    PPP on tama> show ipcp
    what ?
    PPP on tama> pass xxxx
    PPP ON tama> show ipcp
    IPCP [OPEND]
      his side: xxxx
      ....

.Pp
Each
.Nm
daemon has an associated port number which is computed as "3000 +
tunnel_device_number". If 3000 is not good base number, edit defs.h in
the ppp sources (
.Pa /usr/src/usr.sbin/ppp )
and recompile it.

When an outgoing packet is detected,
.Nm
will perform the dialing action (chat script) and try to connect
with the peer.

If the connect fails, the default behavior is to wait 30 seconds
and then attempt to connect when another outgoing packet is detected.
This behavior can be changed with
.Bd -literal -offset indent
set redial seconds|random [dial_attempts]
.Ed
.Pp
Seconds is the number of seconds to wait before attempting
to connect again. If the argument is
.Sq random ,
the delay period is a random value between 0 and 30 seconds.
.Sq dial_attempts
is the number of times to try to connect for each outgoing packet
that is received. The previous value is unchanged if this parameter
is omitted.  If a value of zero is specified for
.Sq dial_attempts ,
.Nm ppp
will keep trying until a connection is made.
.Bd -literal -offset indent
set redial 10 4
.Ed
.Pp
will attempt to connect 4 times for each outgoing packet that is
detected with a 10 second delay between each attempt.  If multiple
phone numbers are specified, the total number of attempts is still
4 (it does not attempt each number 4 times).

Modifying the dial delay is very useful when running
.Nm
in demand
dial mode on both ends of the link. If each end has the same timeout,
both ends wind up calling each other at the same time if the link
drops and both ends have packets queued.

 To terminate the program, type

  PPP ON tama> close
  ppp ON tama> quit all

.Pp
A simple
.Dq quit
command will terminate the telnet connection but not the program itself.
You must use
.Dq quit all
to terminate the program as well.

.Sh PACKET ALIASING

The
.Fl alias
command line option enables packet aliasing.  This allows the
ppp host to act as a masquerading gateway for other computers over
a local area network.  Outgoing IP packets are are aliased so that
they appear to come from the ppp host, and incoming packets are
de-aliased so that they are routed to the correct machine on the
local area network.

Packet aliasing allows computers on private, unregistered
subnets to have internet access, although they are invisible
from the outside world.

In general, correct ppp operation should first be verified
with packet aliasing disabled.  Then, the 
.Fl alias
option should be switched on, and network applications (web browser,
telnet, ftp, ping, traceroute) should be checked on the ppp host.
Finally, the same or similar applications should be checked on other
computers in the LAN.

If network applications work correctly on the ppp host, but not on
other machines in the LAN, then the masquerading software is working
properly, but the host is either not forwarding or possibly receiving
IP packets.  Check that IP forwarding is enabled in /etc/sysconfig
and that other machines have designated the ppp host as the gateway
for the LAN.

.Sh PACKET FILTERING

This implementation supports packet filtering. There are three kinds of
filters: ifilter, ofilter and dfilter.  Here are the basics:

.Bl -bullet -compact
.It
A filter definition has the following syntax:

set filter-name rule-no action [src_addr/src_width] [dst_addr/dst_width]
[proto [src [lt|eq|gt] port ]] [dst [lt|eq|gt] port] [estab]
.Bl -enum
.It
.Sq filter-name
should be one of ifilter, ofilter, or dfilter.
.It
There are two actions:
.Sq permit
and
.Sq deny .
If a given packet
matches the rule, the associated action is taken immediately.
.It
.Sq src_width
and
.Sq dst_width
work like a netmask to represent an address range.
.It
.Sq proto
must be one of icmp, udp or tcp.
.It
.Sq port number
can be specified by number and service name from
.Pa /etc/services .

.El

.It
Each filter can hold up to 20 rules, starting from rule 0.

The entire rule set is not effective until rule 0 is defined.

.It
If no rule is matched to a packet, that packet will be discarded
(blocked).

.It
Use
.Dq set filter-name -1
to flush all rules.

.El

See
.Pa /etc/ppp/ppp.conf.filter.example .


.Sh RECEIVING INCOMING PPP CONNECTIONS (Method 1)

To handle an incoming
.Em PPP
connection request, follow these steps:

.Bl -enum
.It
Make sure the modem and (optionally)
.Pa /etc/rc.serial
is configured correctly.
.Bl -bullet -compact
.It
Use Hardware Handshake (CTS/RTS) for flow control.
.It
Modem should be set to NO echo back (ATE0) and NO results string (ATQ1).
.El

.It
Edit
.Pa /etc/ttys
to enable a getty on the port where the modem is attached.

For example:

.Dl ttyd1  "/usr/libexec/getty std.38400" dialup on secure

Don't forget to send a HUP signal to the init process to start the getty.

.Dl # kill -HUP 1

.It
Prepare an account for the incoming user.
.Bd -literal
ppp:xxxx:66:66:PPP Login User:/home/ppp:/usr/local/bin/ppplogin
.Ed

.It
Create a
.Pa /usr/local/bin/ppplogin
file with the following contents:
.Bd -literal -offset indent
#!/bin/sh -p
exec /usr/sbin/ppp -direct
.Ed

(You can specify a label name for further control.)

.Pp
Direct mode (
.Fl direct )
lets
.Nm
work with stdin and stdout.  You can also telnet to port 3000 to get
command mode control in the same manner as client-side
.Nm.

.It
Optional support for Microsoft's IPCP Name Server and NetBIOS
Name Server negotiation can be enabled use
.Dq enable msext
and 
.Dq set ns pri-addr [sec-addr]
along with
.Dq set nbns pri-addr [sec-addr]
in your ppp.conf file

.El

.Sh RECEIVING INCOMING PPP CONNECTIONS (Method 2)

This method differs in that it recommends the use of 
.Em mgetty+sendfax
to handle the modem connections.  The latest version 0.99
can be compiled with the
.Dq AUTO_PPP
option to allow detection of clients speaking PPP to the login
prompt.

Follow these steps:

.Bl -enum
.It
Get, configure, and install mgetty+sendfax v0.99 or later (beta)
making sure you have used the AUTO_PPP option.
.It
Edit
.Pa /etc/ttys
to enable a mgetty on the port where the modem is attached.

For example:

.Dl cuaa1  "/usr/local/sbin/mgetty -s 57600"       dialup on

.It
Prepare an account for the incoming user.
.Bd -literal
Pfred:xxxx:66:66:Fred's PPP:/home/ppp:/etc/ppp/ppp-dialup
.Ed

.It
Examine the files
.Pa /etc/ppp/sample.ppp-dialup
.Pa /etc/ppp/sample.ppp-pap-dialup
and
.Pa /etc/ppp/sample.ppp.conf
for ideas.   ppp-pap-dialup is supposed to be called from
.Pa /usr/local/etc/mgetty+sendfax/login.conf
from a line like

.Dl /AutoPPP/ -     -       /etc/ppp/ppp-pap-dialup
.El

.Sh SETTING IDLE, LINE QUALITY REQUEST, RETRY TIMER

To check/set idletimer, use the
.Dq show timeout
and
.Dq set timeout [lqrtimer [retrytimer]]
commands.

 Ex:
.Dl ppp ON tama> set timeout 600

The timeout period is measured in seconds, the  default values for which
are timeout = 180 or 3 min, lqrtimer = 30sec and retrytimer = 3sec.
To disable the idle timer function,
use the command
.Dq set timeout 0 .

In
.Fl auto
mode, an idle timeout causes the
.Em PPP
session to be
closed, though the
.Nm
program itself remains running.  Another trigger packet will cause it to
attempt to reestablish the link.

.Sh Predictor-1 compression

This version supports CCP and Predictor type 1 compression based on
the current IETF-draft specs. As a default behavior,
.Nm
will attempt to use (or be willing to accept) this capability when the
peer agrees (or requests it).

To disable CCP/predictor functionality completely, use the
.Dq disable pred1
and
.Dq deny pred1
commands.

.Sh Controlling IP address

.Nm
uses IPCP to negotiate IP addresses. Each side of the connection
specifies the IP address that it's willing to use, and if the requested
IP address is acceptable then
.Nm
returns ACK to the requester.  Otherwise,
.Nm
returns NAK to suggest that the peer use a different IP address. When
both sides of the connection agree to accept the received request (and
send ACK), IPCP is set to the open state and a network level connection
is established.

To control this IPCP behavior, this implementation has the
.Dq set ifaddr
command for defining the local and remote IP address:

.Nm set ifaddr
.Op src_addr Op dst_addr Op netmask Op trg_addr

Where,
.Sq src_addr
is the IP address that the local side is willing to use and
.Sq dst_addr
is the IP address which the remote side should use.
.Sq netmask
is interface netmask.
.Sq trg_addr
is the IP address which used in address negotiation.

Ex:
.Dl set ifaddr 192.244.177.38 192.244.177.2 255.255.255.0

The above specification means:
.Bl -bullet -compact
.It
I strongly want to use 192.244.177.38 as my IP address, and I'll
disagree if the peer suggests that I use another address.

.It
I strongly insist that peer use 192.244.177.2 as own side address and
don't permit it to use any IP address but 192.244.177.2.  When peer
request another IP address, I always suggest that it use 192.244.177.2.

.It
My interface netmask will be 255.255.255.0.

.It
This is all fine when each side has a pre-determined IP address, however
it is often the case that one side is acting as a server which controls
all IP addresses and the other side should obey the direction from it.
.El

In order to allow more flexible behavior, `ifaddr' variable allows the
user to specify IP address more loosely:

.Dl set ifaddr 192.244.177.38/24 192.244.177.2/20

A number followed by a slash (/) represent the number of bits significant in
the IP address.  The above example signifies that:

.Bl -bullet -compact
.It
I'd like to use 192.244.177.38 as my address if it is possible, but I'll
also accept any IP address between 192.244.177.0 and 192.244.177.255.

.It
I'd like to make him use 192.244.177.2 as his own address, but I'll also
permit him to use any IP address between 192.244.176.0 and
192.244.191.255.

.It
As you may have already noticed, 192.244.177.2 is equivalent to saying
192.244.177.2/32.

.It
As an exception, 0 is equivalent to 0.0.0.0/0, meaning that I have no
preferred IP address and will obey the remote peer's selection.

.It
192.244.177.2/0 means that I'll accept/permit any IP address but I'll
try to insist that 192.244.177.2 be used first.
.El

.Sh Connecting with your service provider

The following steps should be taken when connecting to your ISP:

.Bl -enum
.It
Describe your provider's phone number(s) in the dial script using the
.Dq set phone
command.  This command allows you to set multiple phone numbers for
dialing and redialing separated by a colon (:).  For example:
.Bd -literal -offset indent
set phone "1234567:2345678"
.Ed
.Pp
Here, the first number is attempted.  If the connection fails, the second
number is attempted immediately.  The redial timeout is ignored (although
the value of dial_attempts is not - see above).  If the second number
also fails, the first is tried again after the redial timeout has expired.
The selected phone number is substituted for the \\T string in the
.Dq set dial
command (see below).

.It
Set up your redial requirements using
.Dq set redial .
For example, if you have a bad telephone line or your provider is
usually engaged (not so common these days), you may want to specify
the following:
.Bd -literal -offset indent
set redial 10 4
.Ed
.Pp
This says that up to 4 phone calls should be attempted with a pause of 10
seconds before dialing the first number again.

.It
Describe your login procedure using the
.Dq set dial
and
.Dq set login
commands.  The
.Dq set dial
command is used to talk to your modem and establish a link with your
ISP, for example:
.Bd -literal -offset indent
set dial "ABORT BUSY ABORT NO\\\\sCARRIER TIMEOUT 4 \\"\\" ATZ OK-ATZ-OK ATDT\\\\T TIMEOUT 60 CONNECT"
.Ed
.Pp
This modem "chat" string means:

.Bl -bullet
.It
Abort if the string "BUSY" or "NO CARRIER" are received.
.It
Set the timeout to 4.
.It
Expect nothing.
.It
Send ATZ.
.It
Expect OK.  If that's not received, send ATZ and expect OK.
.It
Send ATDTxxxxxxx where xxxxxxx is the next number in the phone list from
above.
.It
Set the timeout to 60.
.It
Wait for the CONNECT string.
.El

Once the connection is established, the login script is executed.  This
script is written in the same style as the dial script:
.Bd -literal -offset indent
set login "TIMEOUT 15 login:-\\\\r-login: awfulhak word: xxx ocol: PPP HELLO"
.Ed
.Pp
This login "chat" string means:

.Bl -bullet
.It
Set the timeout to 15 seconds.
.It
Expect "login:".  If it's not received, send a carriage return and expect
"login:" again.
.It
Send "awfulhak"
.It
Expect "word:" (the tail end of a "Password:" prompt).
.It
Send "xxx".
.It
Expect "ocol:" (the tail end of a "Protocol:" prompt).
.It
Send "PPP".
.It
Expect "HELLO".
.El
.Pp
Login scripts vary greatly between ISPs.

.It
Use
.Dq set line
and
.Dq set sp
to specify your serial line and speed, for example:
.Bd -literal -offset indent
set line /dev/cuaa0
set sp 115200
.Ed
.Pp
Cuaa0 is the first serial port on FreeBSD.  Cuaa1 is the second etc.  A
speed of 115200 should be specified if you have a modem capable of bit
rates of 28800 or more.  In general, the serial speed should be about
four times the modem speed.

.It
Use
.Dq set ifaddr
command to define the IP address.
.Bl -bullet
.It
If you know what IP address your provider uses, then use it as the remote
address, otherwise choose something like 10.0.0.2/0 (see below).
.It
If your provider has assigned a particular IP address to you, then use
it as your address.
.It
If your provider assigns your address dynamically, choose a suitably
unobtrusive and unspecific IP number as your address.  10.0.0.1/0 would
be appropriate.  The bit after the / specifies how many bits of the
address you consider to be important, so if you wanted to insist on
something in the class C network 1.2.3.0, you could specify 1.2.3.0/24.
.El
.Pp
An example for a connection where you don't know your IP number or your
ISPs IP number would be:
.Bd -literal -offset indent
set ifaddr 10.0.0.1/0 10.0.0.2/0
.Ed

.It
In most cases, your ISP will also be your default router.  If this is
the case, add the lines
.Bd -literal -offset indent
delete ALL
add 0 0 HISADDR
.Ed
.Pp
to
.Pa ppp.conf .
.Pp
This tells
.Nm ppp
to delete all routing entries already made by
.Nm ppp ,
then to add a default route to HISADDR.  HISADDR is a macro meaning the
"other side"s IP number.
.Pp
If you're using dynamic IP numbers, you must also put these two lines
in the
.Pa ppp.linkup
file.  Then, once the link has been established and
.Nm ppp
knows the actual IP numbers in use, all previous (and probably incorrect)
entries are deleted and a default to the correct IP number is added.  Use
the same label as the one used in
.Pa ppp.conf .
.Pp
If commands are being typed interactively, the only requirement is
to type
.Bd -literal -offset indent
add 0 0 HISADDR
.Ed
.Pp
after a successful dial.

.It
If your provider requests that you use PAP/CHAP authentication methods, add
the next lines to your
.Pa ppp.conf
file:
.Bd -literal -offset indent
enable pap (or enable chap)
disable chap (or disable pap)
set authname MyName
set authkey MyPassword
.Ed

.It
It is also worth adding the following line:
.Bd -literal -offset indent
set openmode active
.Ed
.Pp
This tells
.Nm ppp
to initiate LCP.  Without this line, there's a possibility
of both sides of the connection just sitting there and looking at
eachother rather than communicating.

.El

Please refer to
.Pa /etc/ppp/ppp.conf.sample
and
.Pa /etc/ppp/ppp.linkup.sample
for some real examples.  The pmdemand label should be appropriate for most
ISPs.

.Sh Logging facility

.Nm
is able to generate the following log info into
.Pa /var/log/ppp.log :

.Bl -column SMMMMMM -offset indent -compat
.It Li Phase	Phase transition log output
.It Li Chat	Generate Chat script trace log
.It Li Connect	Generate complete Chat log
.It Li Carrier	Log Chat lines with 'CARRIER'
.It Li LQM	Generate LQR report
.It Li LCP	Generate LCP/IPCP packet trace
.It Li Link	Log address assignments and link up/down events
.It Li TCP/IP	Dump TCP/IP packet
.It Li HDLC	Dump HDLC packet in hex
.It Li Async	Dump async level packet in hex
.El

The
.Dq set debug
command allows you to set logging output level, of which
multiple levels can be specified.  The default is equivalent to
.Dq set debug carrier link phase .

If a HUP signal is received, the log file is closed and re-opened
to facilitate log file rotation.

.Sh MORE DETAILS

.Bl -bullet -compact
.It
Please read the Japanese doc for complete explanation. It may not be
useful for non-japanese readers,  but examples in the document may help
you to guess.

.It
Please read example configuration files.

.It
Use
.Dq help ,
.Dq show ? ,
.Dq set ?
and
.Dq set ? <var>
commands.

.It
NetBSD and BSDI-1.0 were supported in previous releases but are no
longer supported in this release.  Please contact the author if you need
old driver code.
.El

.Sh FILES
.Nm
refers to three files: ppp.conf, ppp.linkup and ppp.secret.
These files are placed in
.Pa /etc/ppp ,
but the user can create his own files under his $HOME directory as
.Pa .ppp.conf ,
.Pa .ppp.linkup
and
.Pa .ppp.secret.
.Nm
will always try to consult the user's personal setup first.

.Bl -tag -width flag
.Pa $HOME/ppp/.ppp.[conf|linkup|secret]
User dependent configuration files.

.Pa /etc/ppp/ppp.conf
System default configuration file.

.Pa /etc/ppp/ppp.secret
An authorization file for each system.

.Pa /etc/ppp/ppp.linkup
A file to check when
.Nm
establishes a network level connection.

.Pa /var/log/ppp.log
Logging and debugging information file.

.Pa /var/spool/lock/Lck..* 
tty port locking file.

.Pa /var/run/PPP.system
Holds the pid for ppp -auto system.

.Pa /var/run/ppp.tun0.pid
The process id (pid) of the ppp program connected to the ppp0 device.

.Pa /etc/services
Get port number if port number is using service name.
.El
.Sh SEE ALSO
.Xr chat 8 ,
.Xr pppd 8
.Sh HISTORY
This program was submitted in FreeBSD-2.0.5 Atsushi Murai (amurai@spec.co.jp).

.Sh AUTHORS
Toshiharu OHNO (tony-o@iij.ad.jp)