d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
2dacd5d401
freebsd-skq/sys/dev/mii/nsphy.c

389 lines
11 KiB
C
Raw Normal View History

This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* $NetBSD: nsphy.c,v 1.18 1999/07/14 23:57:36 thorpej Exp $ */
/*-
* Copyright (c) 1998, 1999 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Copyright (c) 1997 Manuel Bouyer. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Manuel Bouyer.
* 4. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
Remove double __FBSDID and move the remaining one into a common place after the license(s) and before the driver comment (the latter only in drivers not having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
* driver for National Semiconductor's DP83840A ethernet 10/100 PHY
* Data Sheet available from www.national.com
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/errno.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
Remove miidevs.h and generate it from miidevs at compile time. The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
#include "miidevs.h"
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#include <dev/mii/nsphyreg.h>
#include "miibus_if.h"
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int nsphy_probe(device_t);
static int nsphy_attach(device_t);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
static device_method_t nsphy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, nsphy_probe),
DEVMETHOD(device_attach, nsphy_attach),
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
DEVMETHOD(device_detach, mii_phy_detach),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
DEVMETHOD(device_shutdown, bus_generic_shutdown),
{ 0, 0 }
};
static devclass_t nsphy_devclass;
static driver_t nsphy_driver = {
"nsphy",
nsphy_methods,
sizeof(struct mii_softc)
};
DRIVER_MODULE(nsphy, miibus, nsphy_driver, nsphy_devclass, 0, 0);
Remove __P.
2002-03-20 02:08:01 +00:00
static int nsphy_service(struct mii_softc *, struct mii_data *, int);
static void nsphy_status(struct mii_softc *);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
nsphy_probe(dev)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
device_t dev;
{
struct mii_attach_args *ma;
ma = device_get_ivars(dev);
Added code to handle QS6612 PHY as standard NS PHY for support of tx driver.
2000-04-11 18:39:00 +00:00
if (MII_OUI(ma->mii_id1, ma->mii_id2) == MII_OUI_NATSEMI &&
MII_MODEL(ma->mii_id2) == MII_MODEL_NATSEMI_DP83840) {
device_set_desc(dev, MII_STR_NATSEMI_DP83840);
} else
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (ENXIO);
return (0);
}
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
nsphy_attach(dev)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
device_t dev;
{
struct mii_softc *sc;
struct mii_attach_args *ma;
struct mii_data *mii;
sc = device_get_softc(dev);
ma = device_get_ivars(dev);
sc->mii_dev = device_get_parent(dev);
mii = device_get_softc(sc->mii_dev);
LIST_INSERT_HEAD(&mii->mii_phys, sc, mii_list);
sc->mii_inst = mii->mii_instance;
sc->mii_phy = ma->mii_phyno;
sc->mii_service = nsphy_service;
sc->mii_pdata = mii;
#ifdef foo
/*
* i82557 wedges if all of its PHYs are isolated!
*/
if (strcmp(device_get_name(device_get_parent(sc->mii_dev)),
"fxp") == 0 && mii->mii_instance == 0)
#endif
sc->mii_flags |= MIIF_NOISOLATE;
mii->mii_instance++;
#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
#if 0
/* Can't do this on the i82557! */
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_NONE, 0, sc->mii_inst),
BMCR_ISO);
#endif
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_LOOP, sc->mii_inst),
BMCR_LOOP|BMCR_S100);
mii_phy_reset(sc);
sc->mii_capabilities =
PHY_READ(sc, MII_BMSR) & ma->mii_capmask;
device_printf(dev, " ");
Don't pass three args when one will do just fine, and even prevent mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
mii_add_media(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
printf("\n");
#undef ADD
MIIBUS_MEDIAINIT(sc->mii_dev);
return(0);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
nsphy_service(sc, mii, cmd)
struct mii_softc *sc;
struct mii_data *mii;
int cmd;
{
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
int reg;
DP83840A on hme(4) don't advertise their media capabilities themselves properly. This causes the autonegotiation to e.g. never establish a 100baseTX full-duplex link. The solution to this problem is to manually write the capabilities from the BMSR to the ANAR every time a media change occurs, even when already in autonegotiation mode. The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which will set the ANAR according to the BMSR) even when the PHY alread is in autonegotiation mode. However, while doing the same on FreeBSD (which involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia() causes this driver to no longer work properly in the other modes. Another drawback of that approach is that this will also force writing the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is known to be used together with 3 different PHYs while only the DP83840A require this workaround). So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in nsphy_service() unconditionally when hanging off of a hme(4) and serving a media change This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
2004-05-29 18:23:26 +00:00
device_t parent;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
switch (cmd) {
case MII_POLLSTAT:
/*
* If we're not polling our PHY instance, just return.
*/
if (IFM_INST(ife->ifm_media) != sc->mii_inst)
return (0);
break;
case MII_MEDIACHG:
/*
* If the media indicates a different PHY instance,
* isolate ourselves.
*/
if (IFM_INST(ife->ifm_media) != sc->mii_inst) {
reg = PHY_READ(sc, MII_BMCR);
PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO);
return (0);
}
/*
* If the interface is not up, don't do anything.
*/
if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
break;
DP83840A on hme(4) don't advertise their media capabilities themselves properly. This causes the autonegotiation to e.g. never establish a 100baseTX full-duplex link. The solution to this problem is to manually write the capabilities from the BMSR to the ANAR every time a media change occurs, even when already in autonegotiation mode. The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which will set the ANAR according to the BMSR) even when the PHY alread is in autonegotiation mode. However, while doing the same on FreeBSD (which involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia() causes this driver to no longer work properly in the other modes. Another drawback of that approach is that this will also force writing the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is known to be used together with 3 different PHYs while only the DP83840A require this workaround). So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in nsphy_service() unconditionally when hanging off of a hme(4) and serving a media change This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
2004-05-29 18:23:26 +00:00
parent = device_get_parent(sc->mii_dev);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
reg = PHY_READ(sc, MII_NSPHY_PCR);
/*
* Set up the PCR to use LED4 to indicate full-duplex
* in both 10baseT and 100baseTX modes.
*/
reg |= PCR_LED4MODE;
/*
Spelling fix in a comment.
2004-05-29 16:54:59 +00:00
* Make sure Carrier Integrity Monitor function is
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* disabled (normal for Node operation, but sometimes
* it's not set?!)
*/
reg |= PCR_CIMDIS;
/*
* Make sure "force link good" is set to normal mode.
* It's only intended for debugging.
*/
reg |= PCR_FLINK100;
/*
* Mystery bits which are supposedly `reserved',
* but we seem to need to set them when the PHY
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
* is connected to some interfaces:
*
* 0x0400 is needed for fxp
* (Intel EtherExpress Pro 10+/100B, 82557 chip)
* (nsphy with a DP83840 chip)
* 0x0100 may be needed for some other card
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
reg |= 0x0100 | 0x0400;
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
DP83840A on hme(4) don't advertise their media capabilities themselves properly. This causes the autonegotiation to e.g. never establish a 100baseTX full-duplex link. The solution to this problem is to manually write the capabilities from the BMSR to the ANAR every time a media change occurs, even when already in autonegotiation mode. The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which will set the ANAR according to the BMSR) even when the PHY alread is in autonegotiation mode. However, while doing the same on FreeBSD (which involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia() causes this driver to no longer work properly in the other modes. Another drawback of that approach is that this will also force writing the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is known to be used together with 3 different PHYs while only the DP83840A require this workaround). So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in nsphy_service() unconditionally when hanging off of a hme(4) and serving a media change This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
2004-05-29 18:23:26 +00:00
if (strcmp(device_get_name(parent), "fxp") == 0)
Only touch the PCR register in order to set bits for the fxp driver. The 3C509-TX card apparently had a slightly different version of the chip, and has problems when this register is set. The problem does not appear on the 3C509{BC} cards, but since only the fxp driver needs specific bits set, conditionalize on that.
2001-06-02 19:51:02 +00:00
PHY_WRITE(sc, MII_NSPHY_PCR, reg);
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
switch (IFM_SUBTYPE(ife->ifm_media)) {
case IFM_AUTO:
/*
DP83840A on hme(4) don't advertise their media capabilities themselves properly. This causes the autonegotiation to e.g. never establish a 100baseTX full-duplex link. The solution to this problem is to manually write the capabilities from the BMSR to the ANAR every time a media change occurs, even when already in autonegotiation mode. The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which will set the ANAR according to the BMSR) even when the PHY alread is in autonegotiation mode. However, while doing the same on FreeBSD (which involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia() causes this driver to no longer work properly in the other modes. Another drawback of that approach is that this will also force writing the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is known to be used together with 3 different PHYs while only the DP83840A require this workaround). So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in nsphy_service() unconditionally when hanging off of a hme(4) and serving a media change This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
2004-05-29 18:23:26 +00:00
* If we're already in auto mode and don't hang off
* of a hme(4), just return. DP83840A on hme(4) don't
* advertise their media capabilities themselves
* properly so force writing the ANAR according to
* the BMSR by mii_phy_auto() every time.
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
DP83840A on hme(4) don't advertise their media capabilities themselves properly. This causes the autonegotiation to e.g. never establish a 100baseTX full-duplex link. The solution to this problem is to manually write the capabilities from the BMSR to the ANAR every time a media change occurs, even when already in autonegotiation mode. The NetBSD way of doing this is to set their MIIF_FORCEANEG flag in the NIC driver. This causes mii_phy_setmedia() to call mii_phy_auto() (which will set the ANAR according to the BMSR) even when the PHY alread is in autonegotiation mode. However, while doing the same on FreeBSD (which involves porting the MIIF_FORCEANEG flag and converting nsphy.c to use mii_phy_setmedia()) fixes autonegotiation, using mii_phy_setmedia() causes this driver to no longer work properly in the other modes. Another drawback of that approach is that this will also force writing the ANAR on other PHYs whose drivers use mii_phy_setmedia() and which are used with a NIC whose driver sets MIIF_FORCEANEG (e.g. hme(4) is known to be used together with 3 different PHYs while only the DP83840A require this workaround). So instead of moving to MIIF_FORCEANEG, just call mii_phy_auto() in nsphy_service() unconditionally when hanging off of a hme(4) and serving a media change This is part 1/2 of fixing autonegotiation on hme(4) using DP83840A PHYs.
2004-05-29 18:23:26 +00:00
if ((PHY_READ(sc, MII_BMCR) & BMCR_AUTOEN) == 0 &&
strcmp(device_get_name(parent), "hme") != 0)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
Clean up mii/phy drivers: Remove the MIIF_DOINGAUTO which doesn't really do anything at the end of the day except bloat the drivers which has copy&pasted it.
2002-05-04 11:00:30 +00:00
(void) mii_phy_auto(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
break;
case IFM_100_T4:
/*
* XXX Not supported as a manual setting right now.
*/
return (EINVAL);
default:
/*
* BMCR data is stored in the ifmedia entry.
*/
PHY_WRITE(sc, MII_ANAR,
mii_anar(ife->ifm_media));
PHY_WRITE(sc, MII_BMCR, ife->ifm_data);
}
break;
case MII_TICK:
/*
* If we're not currently selected, just return.
*/
if (IFM_INST(ife->ifm_media) != sc->mii_inst)
return (0);
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
if (mii_phy_tick(sc) == EJUSTRETURN)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
break;
}
/* Update the media status. */
nsphy_status(sc);
/* Callback if something changed. */
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
mii_phy_update(sc, cmd);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static void
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
nsphy_status(sc)
struct mii_softc *sc;
{
struct mii_data *mii = sc->mii_pdata;
int bmsr, bmcr, par, anlpar;
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
bmsr = PHY_READ(sc, MII_BMSR) |
PHY_READ(sc, MII_BMSR);
if (bmsr & BMSR_LINK)
mii->mii_media_status |= IFM_ACTIVE;
bmcr = PHY_READ(sc, MII_BMCR);
if (bmcr & BMCR_ISO) {
mii->mii_media_active |= IFM_NONE;
mii->mii_media_status = 0;
return;
}
if (bmcr & BMCR_LOOP)
mii->mii_media_active |= IFM_LOOP;
if (bmcr & BMCR_AUTOEN) {
/*
* The PAR status bits are only valid of autonegotiation
* has completed (or it's disabled).
*/
if ((bmsr & BMSR_ACOMP) == 0) {
/* Erg, still trying, I guess... */
mii->mii_media_active |= IFM_NONE;
return;
}
/*
* Argh. The PAR doesn't seem to indicate duplex mode
* properly! Determine media based on link partner's
* advertised capabilities.
*/
if (PHY_READ(sc, MII_ANER) & ANER_LPAN) {
anlpar = PHY_READ(sc, MII_ANAR) &
PHY_READ(sc, MII_ANLPAR);
if (anlpar & ANLPAR_T4)
mii->mii_media_active |= IFM_100_T4;
else if (anlpar & ANLPAR_TX_FD)
mii->mii_media_active |= IFM_100_TX|IFM_FDX;
else if (anlpar & ANLPAR_TX)
mii->mii_media_active |= IFM_100_TX;
else if (anlpar & ANLPAR_10_FD)
mii->mii_media_active |= IFM_10_T|IFM_FDX;
else if (anlpar & ANLPAR_10)
mii->mii_media_active |= IFM_10_T;
else
mii->mii_media_active |= IFM_NONE;
return;
}
/*
* Link partner is not capable of autonegotiation.
* We will never be in full-duplex mode if this is
* the case, so reading the PAR is OK.
*/
par = PHY_READ(sc, MII_NSPHY_PAR);
if (par & PAR_10)
mii->mii_media_active |= IFM_10_T;
else
mii->mii_media_active |= IFM_100_TX;
#if 0
if (par & PAR_FDX)
mii->mii_media_active |= IFM_FDX;
#endif
} else
Added code to handle QS6612 PHY as standard NS PHY for support of tx driver.
2000-04-11 18:39:00 +00:00
mii->mii_media_active |= mii_media_from_bmcr(bmcr);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
Reference in New Issue Copy Permalink