d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
3384154590
freebsd-skq/sys/dev/ata/ata-dma.c

1135 lines
37 KiB
C
Raw Normal View History

Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/*-
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
* Copyright (c) 1998,1999,2000,2001 S<EFBFBD>ren Schmidt
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
$Id$ -> $FreeBSD$
1999-08-28 01:08:13 +00:00
* $FreeBSD$
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
*/
#include "pci.h"
#include <sys/param.h>
#include <sys/systm.h>
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
#include <sys/ata.h>
Separate the struct bio related stuff out of <sys/buf.h> into <sys/bio.h>. <sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall not be made a nested include according to bdes teachings on the subject of nested includes. Diskdrivers and similar stuff below specfs::strategy() should no longer need to include <sys/buf.> unless they need caching of data. Still a few bogus uses of struct buf to track down. Repocopy by: peter
2000-05-05 09:59:14 +00:00
#include <sys/bio.h>
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#include <sys/malloc.h>
Update to use the new-bus framework. No functional changes. Mostly done by Doug Rabson, minor fixes by me.
1999-04-18 20:48:15 +00:00
#include <sys/bus.h>
Try a little harder at the VIA DMA support. Only use UDMA66 on 82C686 and with prober cable.
1999-12-07 22:07:18 +00:00
#include <sys/disk.h>
#include <sys/devicestat.h>
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#include <vm/vm.h>
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#include <vm/pmap.h>
#include <pci/pcivar.h>
* Completely rewrite the alpha busspace to hide the implementation from the drivers. * Remove legacy inx/outx support from chipset and replace with macros which call busspace. * Rework pci config accesses to route through the pcib device instead of calling a MD function directly. With these changes it is possible to cleanly support machines which have more than one independantly numbered PCI busses. As a bonus, the new busspace implementation should be measurably faster than the old one.
2000-08-28 21:48:13 +00:00
#include <machine/bus.h>
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
#include <sys/rman.h>
Remove unneeded includes Pointed out by: phk
2000-09-20 07:00:24 +00:00
#include <dev/ata/ata-all.h>
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
/* prototypes */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static void cyrix_timing(struct ata_softc *, int, int);
static void promise_timing(struct ata_softc *, int, int);
static void hpt_timing(struct ata_softc *, int, int);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
/* misc defines */
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
#ifdef __alpha__
#undef vtophys
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define vtophys(va) alpha_XXX_dmamap((vm_offset_t)va)
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
#endif
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
void *
ata_dmaalloc(struct ata_softc *scp, int device)
{
void *dmatab;
if ((dmatab = malloc(PAGE_SIZE, M_DEVBUF, M_NOWAIT))) {
if (((uintptr_t)dmatab >> PAGE_SHIFT) ^
(((uintptr_t)dmatab + PAGE_SIZE - 1) >> PAGE_SHIFT)) {
ata_printf(scp, device, "dmatab crosses page boundary, no DMA\n");
free(dmatab, M_DEVBUF);
dmatab = NULL;
}
}
return dmatab;
}
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
void
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ata_dmainit(struct ata_softc *scp, int device,
int apiomode, int wdmamode, int udmamode)
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
{
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
device_t parent = device_get_parent(scp->dev);
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
int devno = (scp->channel << 1) + ATA_DEV(device);
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
int error;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
/* set our most pessimistic default mode */
scp->mode[ATA_DEV(device)] = ATA_PIO;
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
if (!scp->r_bmio)
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
/* if simplex controller, only allow DMA on primary channel */
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
if (scp->channel == 1) {
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
ATA_OUTB(scp->r_bmio, ATA_BMSTAT_PORT,
ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT) &
(ATA_BMSTAT_DMA_MASTER | ATA_BMSTAT_DMA_SLAVE));
if (ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT) & ATA_BMSTAT_DMA_SIMPLEX) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device, "simplex device, DMA on primary only\n");
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
/* DMA engine address alignment is usually 1 word (2 bytes) */
scp->alignment = 0x1;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
if (udmamode > 2 && !ATA_PARAM(scp, device)->cblid) {
ata_printf(scp, device,
Spell the word 'limited' with only one 't'.
2000-07-30 17:54:34 +00:00
"DMA limited to UDMA33, non-ATA66 compliant cable\n");
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
udmamode = 2;
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
switch (scp->chiptype) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
case 0x244a8086: /* Intel ICH2 mobile */
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
case 0x244b8086: /* Intel ICH2 */
if (udmamode >= 5) {
int32_t mask48, new48;
int16_t word54;
word54 = pci_read_config(parent, 0x54, 2);
if (word54 & (0x10 << devno)) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER,ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting UDMA5 on Intel chip\n",
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
(error) ? "failed" : "success");
if (!error) {
mask48 = (1 << devno) + (3 << (16 + (devno << 2)));
new48 = (1 << devno) + (1 << (16 + (devno << 2)));
pci_write_config(parent, 0x48,
(pci_read_config(parent, 0x48, 4) &
~mask48) | new48, 4);
Fix the ICH2 ATA100 support, and proberly downgrade the chip setup when going to slower DMA modes on all Intel chips.
2000-08-10 07:34:49 +00:00
pci_write_config(parent, 0x54, word54 | (0x1000<<devno), 2);
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
}
Fix the ICH2 ATA100 support, and proberly downgrade the chip setup when going to slower DMA modes on all Intel chips.
2000-08-10 07:34:49 +00:00
/* make sure eventual ATA100 mode from the BIOS is disabled */
pci_write_config(parent, 0x54,
pci_read_config(parent, 0x54, 2) & ~(0x1000<<devno),2);
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
/* FALLTHROUGH */
Add UDMA66 support to the Intel ICH chip. Submitted by: sakichan@lares.dti.ne.jp
2000-02-22 20:37:01 +00:00
case 0x24118086: /* Intel ICH */
if (udmamode >= 4) {
int32_t mask48, new48;
int16_t word54;
word54 = pci_read_config(parent, 0x54, 2);
if (word54 & (0x10 << devno)) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER,ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting UDMA4 on Intel chip\n",
(error) ? "failed" : "success");
Add UDMA66 support to the Intel ICH chip. Submitted by: sakichan@lares.dti.ne.jp
2000-02-22 20:37:01 +00:00
if (!error) {
mask48 = (1 << devno) + (3 << (16 + (devno << 2)));
new48 = (1 << devno) + (2 << (16 + (devno << 2)));
pci_write_config(parent, 0x48,
(pci_read_config(parent, 0x48, 4) &
~mask48) | new48, 4);
pci_write_config(parent, 0x54, word54 | (1 << devno), 2);
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
}
}
Fix the ICH2 ATA100 support, and proberly downgrade the chip setup when going to slower DMA modes on all Intel chips.
2000-08-10 07:34:49 +00:00
/* make sure eventual ATA66 mode from the BIOS is disabled */
pci_write_config(parent, 0x54,
pci_read_config(parent, 0x54, 2) & ~(1 << devno), 2);
Add UDMA66 support to the Intel ICH chip. Submitted by: sakichan@lares.dti.ne.jp
2000-02-22 20:37:01 +00:00
/* FALLTHROUGH */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
case 0x71118086: /* Intel PIIX4 */
Add support for the Intel 810 chipset (ICH type of chips) Prober support for the VIA 82C686, I finally got the right datasheet. Get rid of atapi_wait, merge it into ata_wait. Avoid a couple of races by using asleep instead of tsleep. Always use 16bit transfers on ISA systems. Clear up the atapi_read/write functions.
2000-01-17 02:04:19 +00:00
case 0x71998086: /* Intel PIIX4e */
case 0x24218086: /* Intel ICH0 */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (udmamode >= 2) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
int32_t mask48, new48;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
ata_printf(scp, device, "%s setting UDMA2 on Intel chip\n",
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
mask48 = (1 << devno) + (3 << (16 + (devno << 2)));
new48 = (1 << devno) + (2 << (16 + (devno << 2)));
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x48,
(pci_read_config(parent, 0x48, 4) &
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
~mask48) | new48, 4);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Fix the ICH2 ATA100 support, and proberly downgrade the chip setup when going to slower DMA modes on all Intel chips.
2000-08-10 07:34:49 +00:00
/* make sure eventual ATA33 mode from the BIOS is disabled */
pci_write_config(parent, 0x48,
pci_read_config(parent, 0x48, 4) & ~(1 << devno), 4);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* FALLTHROUGH */
case 0x70108086: /* Intel PIIX3 */
if (wdmamode >= 2 && apiomode >= 4) {
int32_t mask40, new40, mask44, new44;
/* if SITRE not set doit for both channels */
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
if (!((pci_read_config(parent,0x40,4)>>(scp->channel<<8))&0x4000)) {
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
new40 = pci_read_config(parent, 0x40, 4);
new44 = pci_read_config(parent, 0x44, 4);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (!(new40 & 0x00004000)) {
new44 &= ~0x0000000f;
new44 |= ((new40&0x00003000)>>10)|((new40&0x00000300)>>8);
}
if (!(new40 & 0x40000000)) {
new44 &= ~0x000000f0;
new44 |= ((new40&0x30000000)>>22)|((new40&0x03000000)>>20);
}
new40 |= 0x40004000;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x40, new40, 4);
pci_write_config(parent, 0x44, new44, 4);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
ata_printf(scp, device, "%s setting WDMA2 on Intel chip\n",
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
if (device == ATA_MASTER) {
mask40 = 0x0000330f;
new40 = 0x00002307;
mask44 = 0;
new44 = 0;
}
else {
mask40 = 0x000000f0;
new40 = 0x00000070;
mask44 = 0x0000000f;
new44 = 0x0000000b;
}
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
if (scp->channel) {
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
mask40 <<= 16;
new40 <<= 16;
mask44 <<= 4;
new44 <<= 4;
}
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x40,
(pci_read_config(parent, 0x40, 4) & ~mask40)|
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
new40, 4);
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x44,
(pci_read_config(parent, 0x44, 4) & ~mask44)|
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
new44, 4);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
/* we could set PIO mode timings, but we assume the BIOS did that */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
break;
case 0x12308086: /* Intel PIIX */
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
if (wdmamode >= 2 && apiomode >= 4) {
int32_t word40;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
word40 = pci_read_config(parent, 0x40, 4);
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
word40 >>= scp->channel * 16;
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
/* Check for timing config usable for DMA on controller */
if (!((word40 & 0x3300) == 0x2300 &&
((word40 >> (device == ATA_MASTER ? 0 : 4)) & 1) == 1))
break;
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting WDMA2 on Intel chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
if (!error) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
}
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
break;
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
case 0x522910b9: /* AcerLabs Aladdin IV/V */
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
/* the older Aladdin doesn't support ATAPI DMA on both master & slave */
if (pci_get_revid(parent) < 0xC2 &&
scp->devices & ATA_ATAPI_MASTER && scp->devices & ATA_ATAPI_SLAVE) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
"Aladdin: two atapi devices on this channel, no DMA\n");
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
break;
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
if (udmamode >= 5 && pci_get_revid(parent) >= 0xC4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting UDMA5 on Acer chip\n",
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
(error) ? "failed" : "success");
if (!error) {
int32_t word54 = pci_read_config(parent, 0x54, 4);
pci_write_config(parent, 0x4b,
pci_read_config(parent, 0x4b, 1) | 0x01, 1);
word54 &= ~(0x000f000f << (devno << 2));
word54 |= (0x000f0005 << (devno << 2));
pci_write_config(parent, 0x54, word54, 4);
pci_write_config(parent, 0x53,
pci_read_config(parent, 0x53, 1) | 0x03, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
if (udmamode >= 4 && pci_get_revid(parent) >= 0xC2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting UDMA4 on Acer chip\n",
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
(error) ? "failed" : "success");
if (!error) {
int32_t word54 = pci_read_config(parent, 0x54, 4);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
pci_write_config(parent, 0x4b,
pci_read_config(parent, 0x4b, 1) | 0x01, 1);
word54 &= ~(0x000f000f << (devno << 2));
word54 |= (0x00080005 << (devno << 2));
pci_write_config(parent, 0x54, word54, 4);
pci_write_config(parent, 0x53,
pci_read_config(parent, 0x53, 1) | 0x03, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
}
if (udmamode >= 2 && pci_get_revid(parent) >= 0x20) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting UDMA2 on Acer chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add ATA66 and ATA100 mode support for Acer chipsets. MFC candidate :)
2001-04-06 19:18:35 +00:00
int32_t word54 = pci_read_config(parent, 0x54, 4);
Fix a nasty bug in ata_intr, parens are a good thing if used right. Make the error recovery code a little more obvious. Inform the user if UDMA66 mode couldn't be selected due to a non ATA66 compliant 80pin cable. Minor cosmetics.
2000-05-23 19:05:56 +00:00
word54 &= ~(0x000f000f << (devno << 2));
word54 |= (0x000a0005 << (devno << 2));
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x54, word54, 4);
pci_write_config(parent, 0x53,
pci_read_config(parent, 0x53, 1) | 0x03, 1);
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
scp->flags |= ATA_ATAPI_DMA_RO;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Proberly back down DMA modes on the Acer Aladdin.
2000-12-19 10:37:03 +00:00
/* make sure eventual UDMA mode from the BIOS is disabled */
Try better this time at a patch that properly backspeeds on the Acer chips.
2001-01-07 17:00:09 +00:00
pci_write_config(parent, 0x56, pci_read_config(parent, 0x56, 2) &
~(0x0008 << (devno << 2)), 2);
Proberly back down DMA modes on the Acer Aladdin.
2000-12-19 10:37:03 +00:00
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (wdmamode >= 2 && apiomode >= 4) {
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Add support the the Intel ICH2 mobile Tidy chip name printing a bit.
2001-04-16 21:22:34 +00:00
"%s setting WDMA2 on Acer chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x53,
pci_read_config(parent, 0x53, 1) | 0x03, 1);
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
scp->flags |= ATA_ATAPI_DMA_RO;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
pci_write_config(parent, 0x53,
(pci_read_config(parent, 0x53, 1) & ~0x01) | 0x02, 1);
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
/* we could set PIO mode timings, but we assume the BIOS did that */
break;
Add support for the AMD 766 southbridge incl ATA100 support Fix ATA66 mode for the AMD756, the timing was way to slow
2001-05-14 18:38:22 +00:00
case 0x74111022: /* AMD 766 */
if (udmamode >= 5) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA5 on AMD chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xc6, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
/* FALLTHROUGH */
Add support for ATA66 on newer revisions of the VIA 82C596
2000-04-09 15:08:27 +00:00
case 0x74091022: /* AMD 756 */
if (udmamode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting UDMA4 on AMD chip\n",
Add support for ATA66 on newer revisions of the VIA 82C596
2000-04-09 15:08:27 +00:00
(error) ? "failed" : "success");
if (!error) {
Add support for the AMD 766 southbridge incl ATA100 support Fix ATA66 mode for the AMD756, the timing was way to slow
2001-05-14 18:38:22 +00:00
pci_write_config(parent, 0x53 - devno, 0xc5, 1);
Add support for ATA66 on newer revisions of the VIA 82C596
2000-04-09 15:08:27 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
}
goto via_82c586;
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
case 0x05711106: /* VIA 82C571, 82C586, 82C596, 82C686 */
Add first cut support for the ATA100 capable VIA82c686b.
2001-01-17 09:22:13 +00:00
if (ata_find_dev(parent, 0x06861106, 0x40)) { /* 82C686b */
if (udmamode >= 5) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA5 on VIA chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xf0, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
if (udmamode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA4 on VIA chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xf1, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
}
if (udmamode >= 2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA2 on VIA chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xf4, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
}
}
Correct botchup in last commit that made older VIA chips fail...
2001-01-21 16:13:03 +00:00
else if (ata_find_dev(parent, 0x06861106, 0) || /* 82C686a */
ata_find_dev(parent, 0x05961106, 0x12)) { /* 82C596b */
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
if (udmamode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA4 on VIA chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xe8, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
Add support for the Intel 810 chipset (ICH type of chips) Prober support for the VIA 82C686, I finally got the right datasheet. Get rid of atapi_wait, merge it into ata_wait. Avoid a couple of races by using asleep instead of tsleep. Always use 16bit transfers on ISA systems. Clear up the atapi_read/write functions.
2000-01-17 02:04:19 +00:00
}
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
if (udmamode >= 2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA2 on VIA chip\n",
(error) ? "failed" : "success");
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xea, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
Add support for the Intel 810 chipset (ICH type of chips) Prober support for the VIA 82C686, I finally got the right datasheet. Get rid of atapi_wait, merge it into ata_wait. Avoid a couple of races by using asleep instead of tsleep. Always use 16bit transfers on ISA systems. Clear up the atapi_read/write functions.
2000-01-17 02:04:19 +00:00
}
}
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
else if (ata_find_dev(parent, 0x05961106, 0) || /* 82C596a */
The VIA 586 chip does UDMA from rev 0x3 onwards. MFC candidate!
2001-04-14 18:33:08 +00:00
ata_find_dev(parent, 0x05861106, 0x03)) { /* 82C586b */
Add support for ATA66 on newer revisions of the VIA 82C596
2000-04-09 15:08:27 +00:00
via_82c586:
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
if (udmamode >= 2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting UDMA2 on %s chip\n",
(error) ? "failed" : "success",
Add support for the AMD 766 southbridge incl ATA100 support Fix ATA66 mode for the AMD756, the timing was way to slow
2001-05-14 18:38:22 +00:00
((scp->chiptype == 0x74091022) ||
(scp->chiptype == 0x74111022)) ? "AMD" : "VIA");
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
if (!error) {
pci_write_config(parent, 0x53 - devno, 0xc0, 1);
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
}
if (wdmamode >= 2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
ata_printf(scp, device, "%s setting WDMA2 on %s chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success",
(scp->chiptype == 0x74091022) ? "AMD" : "VIA");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add support for yet another Promise ATA100 variant Minor fix to the VIA setup code.
2001-06-08 09:51:33 +00:00
pci_write_config(parent, 0x53 - devno, 0x0b, 1);
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x4b - devno, 0x31, 1);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
}
/* we could set PIO mode timings, but we assume the BIOS did that */
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
break;
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
case 0x55131039: /* SiS 5591 */
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
if (udmamode >= 2 && pci_get_revid(parent) > 0xc1) {
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting UDMA2 on SiS chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
if (!error) {
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x40 + (devno << 1), 0xa301, 2);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
}
}
if (wdmamode >=2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting WDMA2 on SiS chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
if (!error) {
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(parent, 0x40 + (devno << 1), 0x0301, 2);
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
return;
}
}
/* we could set PIO mode timings, but we assume the BIOS did that */
break;
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
case 0x06491095: /* CMD 649 ATA100 controller */
if (udmamode >= 5) {
u_int8_t umode;
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting UDMA5 on CMD chip\n",
(error) ? "failed" : "success");
if (!error) {
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
umode = pci_read_config(parent, scp->channel ? 0x7b : 0x73, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
umode &= ~(device == ATA_MASTER ? 0x35 : 0xca);
umode |= (device == ATA_MASTER ? 0x05 : 0x0a);
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
pci_write_config(parent, scp->channel ? 0x7b : 0x73, umode, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
/* FALLTHROUGH */
case 0x06481095: /* CMD 648 ATA66 controller */
if (udmamode >= 4) {
u_int8_t umode;
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting UDMA4 on CMD chip\n",
(error) ? "failed" : "success");
if (!error) {
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
umode = pci_read_config(parent, scp->channel ? 0x7b : 0x73, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
umode &= ~(device == ATA_MASTER ? 0x35 : 0xca);
umode |= (device == ATA_MASTER ? 0x15 : 0x4a);
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
pci_write_config(parent, scp->channel ? 0x7b : 0x73, umode, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
return;
}
}
if (udmamode >= 2) {
u_int8_t umode;
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting UDMA2 on CMD chip\n",
(error) ? "failed" : "success");
if (!error) {
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
umode = pci_read_config(parent, scp->channel ? 0x7b : 0x73, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
umode &= ~(device == ATA_MASTER ? 0x35 : 0xca);
umode |= (device == ATA_MASTER ? 0x11 : 0x42);
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
pci_write_config(parent, scp->channel ? 0x7b : 0x73, umode, 1);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
}
/* make sure eventual UDMA mode from the BIOS is disabled */
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
pci_write_config(parent, scp->channel ? 0x7b : 0x73,
Fix ISA only systems.
2000-10-13 12:09:23 +00:00
pci_read_config(parent, scp->channel ? 0x7b : 0x73, 1)&
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
~(device == ATA_MASTER ? 0x35 : 0xca), 1);
/* FALLTHROUGH */
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
case 0x06461095: /* CMD 646 ATA controller */
if (wdmamode >= 2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
ata_printf(scp, device, "%s setting WDMA2 on CMD chip\n",
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
error ? "failed" : "success");
if (!error) {
int32_t offset = (devno < 3) ? (devno << 1) : 7;
pci_write_config(parent, 0x54 + offset, 0x3f, 1);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the SiS 5591 and old PIIX chipsets. Add a missing DELAY(1) in ata_wait. Change the info from ad_version, so the ATA version from the disk can be used to quantify the DAM modes valid for this drive, ie be more selective with turning DMA on on older disks that should not support it.. Fix the probe for BIOS enabled DMA in the generic case, master/slave was reversed in the test. Check the return for ata_command in all cases, and print warnings if it fails. Call ata_dmainit with all dmamodes off when falling back to PIO mode, that should take care of both the Promise & HPT366 controllers not being able to handle the fallback... Cleanup the printf's in the drivers, use the prober device name (if possible) instead of ataN-master/slave.
1999-12-13 10:19:39 +00:00
}
}
/* we could set PIO mode timings, but we assume the BIOS did that */
break;
Add (partial) support for the Cypress ATA controller. Call intr_teardown on detach. Always add non masterdevice from unit 2 upwards. Update to the pccard code, at least some cards are now working, more testing to follow.
2000-02-25 09:48:23 +00:00
case 0xc6931080: /* Cypress 82c693 ATA controller */
if (wdmamode >= 2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting WDMA2 on Cypress chip\n",
Add (partial) support for the Cypress ATA controller. Call intr_teardown on detach. Always add non masterdevice from unit 2 upwards. Update to the pccard code, at least some cards are now working, more testing to follow.
2000-02-25 09:48:23 +00:00
error ? "failed" : "success");
if (!error) {
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
pci_write_config(scp->dev, scp->channel ? 0x4e:0x4c, 0x2020, 2);
Add (partial) support for the Cypress ATA controller. Call intr_teardown on detach. Always add non masterdevice from unit 2 upwards. Update to the pccard code, at least some cards are now working, more testing to follow.
2000-02-25 09:48:23 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
return;
}
}
/* we could set PIO mode timings, but we assume the BIOS did that */
break;
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
case 0x01021078: /* Cyrix 5530 ATA33 controller */
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
scp->alignment = 0xf; /* DMA engine requires 16 byte alignment */
if (udmamode >= 2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
ata_printf(scp, device, "%s setting UDMA2 on Cyrix chip\n",
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(error) ? "failed" : "success");
if (!error) {
cyrix_timing(scp, devno, ATA_UDMA2);
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
}
if (wdmamode >= 2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting WDMA2 on Cyrix chip\n",
(error) ? "failed" : "success");
if (!error) {
cyrix_timing(scp, devno, ATA_WDMA2);
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
return;
}
}
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ata_pio2mode(apiomode), ATA_C_F_SETXFER,
ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device, "%s setting %s on Cyrix chip\n",
(error) ? "failed" : "success",
ata_mode2str(ata_pio2mode(apiomode)));
cyrix_timing(scp, devno, ata_pio2mode(apiomode));
scp->mode[ATA_DEV(device)] = ata_pio2mode(apiomode);
return;
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
case 0x02111166: /* ServerWorks ROSB4 ATA33 controller */
if (udmamode >= 2) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting UDMA2 on ServerWorks chip\n",
(error) ? "failed" : "success");
if (!error) {
Proberly back down DMA modes on the Acer Aladdin.
2000-12-19 10:37:03 +00:00
u_int16_t reg56;
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
pci_write_config(parent, 0x54,
pci_read_config(parent, 0x54, 1) |
(0x01 << devno), 1);
reg56 = pci_read_config(parent, 0x56, 2);
reg56 &= ~(0xf << (devno * 4));
reg56 |= (0x2 << (devno * 4));
pci_write_config(parent, 0x56, reg56, 2);
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
return;
}
}
if (wdmamode >= 2 && apiomode >= 4) {
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
"%s setting WDMA2 on ServerWorks chip\n",
(error) ? "failed" : "success");
if (!error) {
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
int offset = (scp->channel * 2) + (device == ATA_MASTER);
Add support for ServerWorks ROSB4 ATA33 chipset. Add support for CMD 648 ATA66 & CMD 649 ATA100 chipsets. Fix the "resource already allocated" panic with the CMD and other braindead controllers. Add options ATA_ENABLE_TAGS, without this option tagged queuing will not be attempted.
2000-10-03 13:12:36 +00:00
int word44 = pci_read_config(parent, 0x44, 4);
pci_write_config(parent, 0x54,
pci_read_config(parent, 0x54, 1) &
~(0x01 << devno), 1);
word44 &= ~(0xff << (offset << 8));
word44 |= (0x20 << (offset << 8));
pci_write_config(parent, 0x44, 0x20, 4);
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
return;
}
}
/* we could set PIO mode timings, but we assume the BIOS did that */
break;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
case 0x4d33105a: /* Promise Ultra/FastTrak 33 controllers */
case 0x4d38105a: /* Promise Ultra/FastTrak 66 controllers */
case 0x4d30105a: /* Promise Ultra/FastTrak 100 controllers */
case 0x0d30105a: /* Promise OEM ATA100 controllers */
Add support for yet another Promise ATA100 variant Minor fix to the VIA setup code.
2001-06-08 09:51:33 +00:00
case 0x4d68105a: /* Promise TX2 ATA100 controllers */
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
/* the Promise can only do DMA on ATA disks not on ATAPI devices */
if ((device == ATA_MASTER && scp->devices & ATA_ATAPI_MASTER) ||
(device == ATA_SLAVE && scp->devices & ATA_ATAPI_SLAVE))
break;
Add support for yet another Promise ATA100 variant Minor fix to the VIA setup code.
2001-06-08 09:51:33 +00:00
if (udmamode >= 5 && (scp->chiptype == 0x4d30105a ||
scp->chiptype == 0x0d30105a || scp->chiptype == 0x4d68105a) &&
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
!(pci_read_config(parent, 0x50, 2)&(scp->channel ? 1<<11 : 1<<10))){
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting UDMA5 on Promise chip\n",
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
(error) ? "failed" : "success");
if (!error) {
promise_timing(scp, devno, ATA_UDMA5);
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
Add support for yet another Promise ATA100 variant Minor fix to the VIA setup code.
2001-06-08 09:51:33 +00:00
if (udmamode >= 4 &&
(scp->chiptype == 0x4d38105a || scp->chiptype == 0x4d30105a ||
scp->chiptype == 0x0d30105a || scp->chiptype == 0x4d68105a) &&
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
!(pci_read_config(parent, 0x50, 2)&(scp->channel ? 1<<11 : 1<<10))){
Fix IRQ allocation bug on controllers using a shared interrupt. Fix a bug which could cause panics in ad/atapi-interrupt. Add support for UDMA66 on Promise Ultra/Fasttrak controllers. Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead. Add a delay in the dump routine in ata-disk.c, some controllers seem to need this. Also dont use the timeout watchdog when dumping. Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA for those that has HW that works. Add support for some not-up-to-spec ATAPI devices that returns data together with completition status on data moving cmd's.
1999-11-06 16:50:21 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
Fix IRQ allocation bug on controllers using a shared interrupt. Fix a bug which could cause panics in ad/atapi-interrupt. Add support for UDMA66 on Promise Ultra/Fasttrak controllers. Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead. Add a delay in the dump routine in ata-disk.c, some controllers seem to need this. Also dont use the timeout watchdog when dumping. Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA for those that has HW that works. Add support for some not-up-to-spec ATAPI devices that returns data together with completition status on data moving cmd's.
1999-11-06 16:50:21 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting UDMA4 on Promise chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
promise_timing(scp, devno, ATA_UDMA4);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fix IRQ allocation bug on controllers using a shared interrupt. Fix a bug which could cause panics in ad/atapi-interrupt. Add support for UDMA66 on Promise Ultra/Fasttrak controllers. Get rid of ATA_IGNORE_INTR, and introduce ATA_WAIT_INTR instead. Add a delay in the dump routine in ata-disk.c, some controllers seem to need this. Also dont use the timeout watchdog when dumping. Disable DMA on ATAPI devices as default, add option ATA_ENABLE_ATAPI_DMA for those that has HW that works. Add support for some not-up-to-spec ATAPI devices that returns data together with completition status on data moving cmd's.
1999-11-06 16:50:21 +00:00
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (udmamode >= 2) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting UDMA2 on Promise chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
promise_timing(scp, devno, ATA_UDMA2);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (wdmamode >= 2 && apiomode >= 4) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting WDMA2 on Promise chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
promise_timing(scp, devno, ATA_WDMA2);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ata_pio2mode(apiomode),
ATA_C_F_SETXFER, ATA_WAIT_READY);
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting PIO%d on Promise chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success",
(apiomode >= 0) ? apiomode : 0);
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
promise_timing(scp, devno, ata_pio2mode(apiomode));
scp->mode[ATA_DEV(device)] = ata_pio2mode(apiomode);
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
case 0x00041103: /* HighPoint HPT366/368/370 controllers */
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
/* no ATAPI devices for now */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if ((device == ATA_MASTER && scp->devices & ATA_ATAPI_MASTER) ||
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
(device == ATA_SLAVE && scp->devices & ATA_ATAPI_SLAVE))
break;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
if (udmamode >=5 && pci_get_revid(parent) >= 0x03 &&
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
!(pci_read_config(parent, 0x5a, 1) & (scp->channel ? 0x01:0x02))) {
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ATA_UDMA5, ATA_C_F_SETXFER, ATA_WAIT_READY);
if (bootverbose)
ata_printf(scp, device,
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
"%s setting UDMA5 on HighPoint chip\n",
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
(error) ? "failed" : "success");
if (!error) {
hpt_timing(scp, devno, ATA_UDMA5);
scp->mode[ATA_DEV(device)] = ATA_UDMA5;
return;
}
}
if (udmamode >=4 &&
Get rid of the ivars entirely.
2000-10-13 11:21:27 +00:00
!(pci_read_config(parent, 0x5a, 1) & (scp->channel ? 0x01:0x02))) {
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA4, ATA_C_F_SETXFER, ATA_WAIT_READY);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
"%s setting UDMA4 on HighPoint chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
hpt_timing(scp, devno, ATA_UDMA4);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA4;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (udmamode >= 2) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_UDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
"%s setting UDMA2 on HighPoint chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
hpt_timing(scp, devno, ATA_UDMA2);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_UDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (wdmamode >= 2 && apiomode >= 4) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
"%s setting WDMA2 on HighPoint chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
hpt_timing(scp, devno, ATA_WDMA2);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ata_pio2mode(apiomode),
ATA_C_F_SETXFER, ATA_WAIT_READY);
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (bootverbose)
Only allow UDMA2 mode on SiS rev > 0xc1 Minor cosmetics
2000-10-13 10:54:47 +00:00
ata_printf(scp, device, "%s setting PIO%d on HighPoint chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success",
(apiomode >= 0) ? apiomode : 0);
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
hpt_timing(scp, devno, ata_pio2mode(apiomode));
Add sysctl oid hw.atamodes to set the transfermodes online.
2000-01-27 19:00:51 +00:00
scp->mode[ATA_DEV(device)] = ata_pio2mode(apiomode);
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Support quad & max speeds in wormcontrol. A bit more general cleanup.
1999-09-22 12:04:51 +00:00
default: /* unknown controller chip */
/* better not try generic DMA on ATAPI devices it almost never works */
if ((device == ATA_MASTER && scp->devices & ATA_ATAPI_MASTER) ||
(device == ATA_SLAVE && scp->devices & ATA_ATAPI_SLAVE))
break;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
/* if controller says its setup for DMA take the easy way out */
/* the downside is we dont know what DMA mode we are in */
if ((udmamode >= 0 || wdmamode > 1) &&
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
(ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT) &
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
((device==ATA_MASTER) ?
ATA_BMSTAT_DMA_MASTER : ATA_BMSTAT_DMA_SLAVE))) {
scp->mode[ATA_DEV(device)] = ATA_DMA;
return;
}
Support quad & max speeds in wormcontrol. A bit more general cleanup.
1999-09-22 12:04:51 +00:00
/* well, we have no support for this, but try anyways */
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
if ((wdmamode >= 2 && apiomode >= 4) && scp->r_bmio) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
Unbreak ATAPI on the Aladdin chipset, only DMA access worked. Try to use a 32bit mask on the IO addresses, this fixes the alpha and hopefully doesn't break on any i386 machines. Try to enable both read & write cache on disks, they should be as default, but better be sure..
1999-11-08 21:36:00 +00:00
ATA_WDMA2, ATA_C_F_SETXFER, ATA_WAIT_READY);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (bootverbose)
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device,
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
"%s setting WDMA2 on generic chip\n",
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
(error) ? "failed" : "success");
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
if (!error) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
scp->mode[ATA_DEV(device)] = ATA_WDMA2;
Cleanup the ata_dmainit function a bit. Also allow BIOS setup DMA on unknown controllers.
2000-01-28 13:35:43 +00:00
return;
Add DMA support for the VIA 82C586 & 82C686 chips, also rearrange to fall back to slower speeds if the faster ones fails to probe. Log and retry request on UDMA CRC errors. Fix a couple of warnings.
1999-11-24 21:40:05 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
}
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
error = ata_command(scp, device, ATA_C_SETFEATURES, 0, 0, 0,
ata_pio2mode(apiomode), ATA_C_F_SETXFER,ATA_WAIT_READY);
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
if (bootverbose)
Rearrange the probe a bit, hopefully this will help to eleminate some of the fake devices sometimes seen on single device ATA channels. Proberly fail on failures in ata-disk.c, retry instead of hang. Cleanup the VIA probe/init code a bit. Fix a couble of missing free's in atapi-cd.c in the changer code.
2000-08-16 07:09:04 +00:00
ata_printf(scp, device, "%s setting PIO%d on generic chip\n",
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
(error) ? "failed" : "success", apiomode < 0 ? 0 : apiomode);
if (!error)
scp->mode[ATA_DEV(device)] = ata_pio2mode(apiomode);
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
else {
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
if (bootverbose)
ata_printf(scp, device, "using PIO mode set by BIOS\n");
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
scp->mode[ATA_DEV(device)] = ATA_PIO;
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int
ata_dmasetup(struct ata_softc *scp, int device, struct ata_dmaentry *dmatab,
caddr_t data, int32_t count)
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
{
u_int32_t dma_count, dma_base;
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
int i = 0;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
if (((uintptr_t)data & scp->alignment) || (count & scp->alignment)) {
ata_printf(scp, device, "non aligned DMA transfer attempted\n");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
return -1;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (!count) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device, "zero length DMA transfer attempted\n");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
return -1;
}
dma_base = vtophys(data);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
dma_count = min(count, (PAGE_SIZE - ((uintptr_t)data & PAGE_MASK)));
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
data += dma_count;
count -= dma_count;
while (count) {
dmatab[i].base = dma_base;
dmatab[i].count = (dma_count & 0xffff);
i++;
if (i >= ATA_DMA_ENTRIES) {
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ata_printf(scp, device, "too many segments in DMA table\n");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
return -1;
}
dma_base = vtophys(data);
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
dma_count = min(count, PAGE_SIZE);
data += min(count, PAGE_SIZE);
count -= min(count, PAGE_SIZE);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
dmatab[i].base = dma_base;
dmatab[i].count = (dma_count & 0xffff) | ATA_DMA_EOT;
return 0;
}
void
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
ata_dmastart(struct ata_softc *scp, int device,
struct ata_dmaentry *dmatab, int dir)
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
{
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
scp->flags |= ATA_DMA_ACTIVE;
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
ATA_OUTL(scp->r_bmio, ATA_BMDTP_PORT, vtophys(dmatab));
ATA_OUTB(scp->r_bmio, ATA_BMCMD_PORT, dir ? ATA_BMCMD_WRITE_READ : 0);
ATA_OUTB(scp->r_bmio, ATA_BMSTAT_PORT,
(ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT) |
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(ATA_BMSTAT_INTERRUPT | ATA_BMSTAT_ERROR)));
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
ATA_OUTB(scp->r_bmio, ATA_BMCMD_PORT,
ATA_INB(scp->r_bmio, ATA_BMCMD_PORT) | ATA_BMCMD_START_STOP);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
ata_dmadone(struct ata_softc *scp)
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
{
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
int error;
ATA_OUTB(scp->r_bmio, ATA_BMCMD_PORT,
ATA_INB(scp->r_bmio, ATA_BMCMD_PORT) & ~ATA_BMCMD_START_STOP);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
scp->flags &= ~ATA_DMA_ACTIVE;
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
error = ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT);
ATA_OUTB(scp->r_bmio, ATA_BMSTAT_PORT,
error | ATA_BMSTAT_INTERRUPT | ATA_BMSTAT_ERROR);
return error & ATA_BMSTAT_MASK;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
ata_dmastatus(struct ata_softc *scp)
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
{
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
return ATA_INB(scp->r_bmio, ATA_BMSTAT_PORT) & ATA_BMSTAT_MASK;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
}
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
static void
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
cyrix_timing(struct ata_softc *scp, int devno, int mode)
{
u_int32_t reg20 = 0x0000e132;
u_int32_t reg24 = 0x00017771;
switch (mode) {
case ATA_PIO0: reg20 = 0x0000e132; break;
case ATA_PIO1: reg20 = 0x00018121; break;
case ATA_PIO2: reg20 = 0x00024020; break;
case ATA_PIO3: reg20 = 0x00032010; break;
case ATA_PIO4: reg20 = 0x00040010; break;
case ATA_WDMA2: reg24 = 0x00002020; break;
case ATA_UDMA2: reg24 = 0x00911030; break;
}
Introduce busspace instead of the good old in/out instructions. Not pretty but it works (I hope)...
2001-02-06 16:44:25 +00:00
ATA_OUTL(scp->r_bmio, (devno << 3) + 0x20, reg20);
ATA_OUTL(scp->r_bmio, (devno << 3) + 0x24, reg24);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
}
static void
promise_timing(struct ata_softc *scp, int devno, int mode)
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
{
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
u_int32_t timing = 0;
struct promise_timing {
u_int8_t pa:4;
u_int8_t prefetch:1;
u_int8_t iordy:1;
u_int8_t errdy:1;
u_int8_t syncin:1;
u_int8_t pb:5;
u_int8_t mb:3;
u_int8_t mc:4;
u_int8_t dmaw:1;
u_int8_t dmar:1;
u_int8_t iordyp:1;
u_int8_t dmarqp:1;
u_int8_t reserved:8;
} *t = (struct promise_timing*)&timing;
t->iordy = 1; t->iordyp = 1;
if (mode >= ATA_DMA) {
t->prefetch = 1; t->errdy = 1; t->syncin = 1;
}
switch (scp->chiptype) {
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
case 0x4d33105a: /* Promise Ultra/Fasttrak 33 */
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
switch (mode) {
default:
case ATA_PIO0: t->pa = 9; t->pb = 19; t->mb = 7; t->mc = 15; break;
case ATA_PIO1: t->pa = 5; t->pb = 12; t->mb = 7; t->mc = 15; break;
case ATA_PIO2: t->pa = 3; t->pb = 8; t->mb = 7; t->mc = 15; break;
case ATA_PIO3: t->pa = 2; t->pb = 6; t->mb = 7; t->mc = 15; break;
case ATA_PIO4: t->pa = 1; t->pb = 4; t->mb = 7; t->mc = 15; break;
case ATA_WDMA2: t->pa = 3; t->pb = 7; t->mb = 3; t->mc = 3; break;
case ATA_UDMA2: t->pa = 3; t->pb = 7; t->mb = 1; t->mc = 1; break;
}
break;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
case 0x4d38105a: /* Promise Ultra/Fasttrak 66 */
case 0x4d30105a: /* Promise Ultra/Fasttrak 100 */
case 0x0d30105a: /* Promise OEM ATA 100 */
Add support for yet another Promise ATA100 variant Minor fix to the VIA setup code.
2001-06-08 09:51:33 +00:00
case 0x4d68105a: /* Promise TX2 ATA 100 */
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
switch (mode) {
default:
case ATA_PIO0: t->pa = 15; t->pb = 31; t->mb = 7; t->mc = 15; break;
case ATA_PIO1: t->pa = 10; t->pb = 24; t->mb = 7; t->mc = 15; break;
case ATA_PIO2: t->pa = 6; t->pb = 16; t->mb = 7; t->mc = 15; break;
case ATA_PIO3: t->pa = 4; t->pb = 12; t->mb = 7; t->mc = 15; break;
case ATA_PIO4: t->pa = 2; t->pb = 8; t->mb = 7; t->mc = 15; break;
case ATA_WDMA2: t->pa = 6; t->pb = 14; t->mb = 6; t->mc = 6; break;
case ATA_UDMA2: t->pa = 6; t->pb = 14; t->mb = 2; t->mc = 2; break;
case ATA_UDMA4: t->pa = 3; t->pb = 7; t->mb = 1; t->mc = 1; break;
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
case ATA_UDMA5: t->pa = 3; t->pb = 7; t->mb = 1; t->mc = 1; break;
fix support for shared IRQ's. fix support for multiple HPT & Promise controllers. support mixed 33/66 devices on the Promise 66 controllers. fix the refcount stuff in the atapi drivers. misc cleanups.
2000-02-04 10:20:22 +00:00
}
break;
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
}
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
pci_write_config(device_get_parent(scp->dev), 0x60 + (devno<<2), timing, 4);
Add support for VIA 82C596 controller Better shared irq handeling for Promise & HPT366 controllers Setup prober PIO mode timings on Promise & HPT366 controllers Update Copyright headers to be Y2K compliant :)
2000-01-03 10:26:59 +00:00
}
static void
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
hpt_timing(struct ata_softc *scp, int devno, int mode)
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
{
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
device_t parent = device_get_parent(scp->dev);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
u_int32_t timing;
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
if (pci_get_revid(parent) >= 0x03) { /* HPT370 */
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
switch (mode) {
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
case ATA_PIO0: timing = 0x06914e57; break;
case ATA_PIO1: timing = 0x06914e43; break;
case ATA_PIO2: timing = 0x06514e33; break;
case ATA_PIO3: timing = 0x06514e22; break;
case ATA_PIO4: timing = 0x06514e21; break;
case ATA_WDMA2: timing = 0x26514e21; break;
case ATA_UDMA2: timing = 0x16494e31; break;
case ATA_UDMA4: timing = 0x16454e31; break;
case ATA_UDMA5: timing = 0x16454e31; break;
default: timing = 0x06514e57;
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
pci_write_config(parent, 0x40 + (devno << 2) , timing, 4);
pci_write_config(parent, 0x5b, 0x22, 1);
}
else { /* HPT36[68] */
switch (pci_read_config(parent, 0x41 + (devno << 2), 1)) {
case 0x85: /* 25Mhz */
switch (mode) {
case ATA_PIO0: timing = 0xc0d08585; break;
case ATA_PIO1: timing = 0xc0d08572; break;
case ATA_PIO2: timing = 0xc0ca8542; break;
case ATA_PIO3: timing = 0xc0ca8532; break;
case ATA_PIO4: timing = 0xc0ca8521; break;
case ATA_WDMA2: timing = 0xa0ca8521; break;
case ATA_UDMA2: timing = 0x90cf8521; break;
case ATA_UDMA4: timing = 0x90c98521; break;
default: timing = 0x01208585;
}
break;
default:
case 0xa7: /* 33MHz */
switch (mode) {
case ATA_PIO0: timing = 0xc0d0a7aa; break;
case ATA_PIO1: timing = 0xc0d0a7a3; break;
case ATA_PIO2: timing = 0xc0d0a753; break;
case ATA_PIO3: timing = 0xc0c8a742; break;
case ATA_PIO4: timing = 0xc0c8a731; break;
case ATA_WDMA2: timing = 0xa0c8a731; break;
case ATA_UDMA2: timing = 0x90caa731; break;
case ATA_UDMA4: timing = 0x90c9a731; break;
default: timing = 0x0120a7a7;
}
break;
case 0xd9: /* 40Mhz */
switch (mode) {
case ATA_PIO0: timing = 0xc018d9d9; break;
case ATA_PIO1: timing = 0xc010d9c7; break;
case ATA_PIO2: timing = 0xc010d997; break;
case ATA_PIO3: timing = 0xc010d974; break;
case ATA_PIO4: timing = 0xc008d963; break;
case ATA_WDMA2: timing = 0xa008d943; break;
case ATA_UDMA2: timing = 0x900bd943; break;
case ATA_UDMA4: timing = 0x900fd943; break;
default: timing = 0x0120d9d9;
}
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
Add experimental code for ATA100 support on: Promise Ultra100 / Fasttrak100 HighPoint HPT370 controllers (fx Abit KA7-100 onboard ctrl, Abit HotRod 100) Intel ICH2 (Intel 815E based motherboards) So far I can read >90MB/s on the Promise and the HPT370. I can write >64MB/s on the promise and >50MB/s on the HPT370 so it seems writing is still done in ATA66 mode :( The ICH2 support is untested as of yet...
2000-08-06 19:51:58 +00:00
pci_write_config(parent, 0x40 + (devno << 2), (timing & ~0x80000000),4);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
}
}
Reference in New Issue Copy Permalink