2005-01-06 01:43:34 +00:00
|
|
|
/*-
|
2000-09-16 20:02:28 +00:00
|
|
|
* Inline routines shareable across OS platforms.
|
|
|
|
|
*
|
2001-01-27 20:54:24 +00:00
|
|
|
* Copyright (c) 1994-2001 Justin T. Gibbs.
|
2002-04-24 16:58:51 +00:00
|
|
|
* Copyright (c) 2000-2001 Adaptec Inc.
|
2000-09-16 20:02:28 +00:00
|
|
|
* All rights reserved.
|
|
|
|
|
*
|
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
|
* are met:
|
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
|
* notice, this list of conditions, and the following disclaimer,
|
|
|
|
|
* without modification.
|
2002-04-24 16:58:51 +00:00
|
|
|
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
|
|
|
|
|
* substantially similar to the "NO WARRANTY" disclaimer below
|
|
|
|
|
* ("Disclaimer") and any redistribution must be conditioned upon
|
|
|
|
|
* including a substantially similar Disclaimer requirement for further
|
|
|
|
|
* binary redistribution.
|
|
|
|
|
* 3. Neither the names of the above-listed copyright holders nor the names
|
|
|
|
|
* of any contributors may be used to endorse or promote products derived
|
|
|
|
|
* from this software without specific prior written permission.
|
2000-09-16 20:02:28 +00:00
|
|
|
*
|
|
|
|
|
* Alternatively, this software may be distributed under the terms of the
|
2002-04-24 16:58:51 +00:00
|
|
|
* GNU General Public License ("GPL") version 2 as published by the Free
|
|
|
|
|
* Software Foundation.
|
2000-09-16 20:02:28 +00:00
|
|
|
*
|
2002-04-24 16:58:51 +00:00
|
|
|
* NO WARRANTY
|
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
|
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
|
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
|
|
|
|
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
|
|
|
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
2000-09-16 20:02:28 +00:00
|
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
|
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
2002-04-24 16:58:51 +00:00
|
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
|
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
|
|
|
|
|
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
|
|
|
* POSSIBILITY OF SUCH DAMAGES.
|
2000-09-16 20:02:28 +00:00
|
|
|
*
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
* $Id: //depot/aic7xxx/aic7xxx/aic7xxx_inline.h#47 $
|
2000-09-16 20:02:28 +00:00
|
|
|
*
|
|
|
|
|
* $FreeBSD$
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#ifndef _AIC7XXX_INLINE_H_
|
|
|
|
|
#define _AIC7XXX_INLINE_H_
|
|
|
|
|
|
|
|
|
|
/************************* Sequencer Execution Control ************************/
|
|
|
|
|
static __inline void ahc_pause_bug_fix(struct ahc_softc *ahc);
|
2001-07-18 21:39:48 +00:00
|
|
|
static __inline int ahc_is_paused(struct ahc_softc *ahc);
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
static __inline void ahc_pause(struct ahc_softc *ahc);
|
|
|
|
|
static __inline void ahc_unpause(struct ahc_softc *ahc);
|
2000-09-16 20:02:28 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Work around any chip bugs related to halting sequencer execution.
|
|
|
|
|
* On Ultra2 controllers, we must clear the CIOBUS stretch signal by
|
|
|
|
|
* reading a register that will set this signal and deassert it.
|
|
|
|
|
* Without this workaround, if the chip is paused, by an interrupt or
|
|
|
|
|
* manual pause while accessing scb ram, accesses to certain registers
|
|
|
|
|
* will hang the system (infinite pci retries).
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_pause_bug_fix(struct ahc_softc *ahc)
|
|
|
|
|
{
|
|
|
|
|
if ((ahc->features & AHC_ULTRA2) != 0)
|
|
|
|
|
(void)ahc_inb(ahc, CCSCBCTL);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Determine whether the sequencer has halted code execution.
|
|
|
|
|
* Returns non-zero status if the sequencer is stopped.
|
|
|
|
|
*/
|
|
|
|
|
static __inline int
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
ahc_is_paused(struct ahc_softc *ahc)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
|
|
|
|
return ((ahc_inb(ahc, HCNTRL) & PAUSE) != 0);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Request that the sequencer stop and wait, indefinitely, for it
|
|
|
|
|
* to stop. The sequencer will only acknowledge that it is paused
|
|
|
|
|
* once it has reached an instruction boundary and PAUSEDIS is
|
|
|
|
|
* cleared in the SEQCTL register. The sequencer may use PAUSEDIS
|
|
|
|
|
* for critical sections.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
ahc_pause(struct ahc_softc *ahc)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
|
|
|
|
ahc_outb(ahc, HCNTRL, ahc->pause);
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Since the sequencer can disable pausing in a critical section, we
|
|
|
|
|
* must loop until it actually stops.
|
|
|
|
|
*/
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
while (ahc_is_paused(ahc) == 0)
|
2000-09-16 20:02:28 +00:00
|
|
|
;
|
|
|
|
|
|
|
|
|
|
ahc_pause_bug_fix(ahc);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Allow the sequencer to continue program execution.
|
|
|
|
|
* We check here to ensure that no additional interrupt
|
|
|
|
|
* sources that would cause the sequencer to halt have been
|
|
|
|
|
* asserted. If, for example, a SCSI bus reset is detected
|
|
|
|
|
* while we are fielding a different, pausing, interrupt type,
|
|
|
|
|
* we don't want to release the sequencer before going back
|
|
|
|
|
* into our interrupt handler and dealing with this new
|
|
|
|
|
* condition.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
ahc_unpause(struct ahc_softc *ahc)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
|
|
|
|
if ((ahc_inb(ahc, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) == 0)
|
|
|
|
|
ahc_outb(ahc, HCNTRL, ahc->unpause);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*********************** Untagged Transaction Routines ************************/
|
|
|
|
|
static __inline void ahc_freeze_untagged_queues(struct ahc_softc *ahc);
|
|
|
|
|
static __inline void ahc_release_untagged_queues(struct ahc_softc *ahc);
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Block our completion routine from starting the next untagged
|
|
|
|
|
* transaction for this target or target lun.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_freeze_untagged_queues(struct ahc_softc *ahc)
|
|
|
|
|
{
|
2001-01-22 21:03:48 +00:00
|
|
|
if ((ahc->flags & AHC_SCB_BTT) == 0)
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc->untagged_queue_lock++;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Allow the next untagged transaction for this target or target lun
|
|
|
|
|
* to be executed. We use a counting semaphore to allow the lock
|
|
|
|
|
* to be acquired recursively. Once the count drops to zero, the
|
|
|
|
|
* transaction queues will be run.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_release_untagged_queues(struct ahc_softc *ahc)
|
|
|
|
|
{
|
2001-01-22 21:03:48 +00:00
|
|
|
if ((ahc->flags & AHC_SCB_BTT) == 0) {
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc->untagged_queue_lock--;
|
|
|
|
|
if (ahc->untagged_queue_lock == 0)
|
|
|
|
|
ahc_run_untagged_queues(ahc);
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/************************** Memory mapping routines ***************************/
|
|
|
|
|
static __inline struct ahc_dma_seg *
|
|
|
|
|
ahc_sg_bus_to_virt(struct scb *scb,
|
|
|
|
|
uint32_t sg_busaddr);
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_sg_virt_to_bus(struct scb *scb,
|
|
|
|
|
struct ahc_dma_seg *sg);
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index);
|
2001-07-18 21:39:48 +00:00
|
|
|
static __inline void ahc_sync_scb(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb, int op);
|
|
|
|
|
static __inline void ahc_sync_sglist(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb, int op);
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_targetcmd_offset(struct ahc_softc *ahc,
|
|
|
|
|
u_int index);
|
2000-09-16 20:02:28 +00:00
|
|
|
|
|
|
|
|
static __inline struct ahc_dma_seg *
|
|
|
|
|
ahc_sg_bus_to_virt(struct scb *scb, uint32_t sg_busaddr)
|
|
|
|
|
{
|
|
|
|
|
int sg_index;
|
|
|
|
|
|
|
|
|
|
sg_index = (sg_busaddr - scb->sg_list_phys)/sizeof(struct ahc_dma_seg);
|
|
|
|
|
/* sg_list_phys points to entry 1, not 0 */
|
|
|
|
|
sg_index++;
|
|
|
|
|
|
|
|
|
|
return (&scb->sg_list[sg_index]);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_sg_virt_to_bus(struct scb *scb, struct ahc_dma_seg *sg)
|
|
|
|
|
{
|
|
|
|
|
int sg_index;
|
|
|
|
|
|
|
|
|
|
/* sg_list_phys points to entry 1, not 0 */
|
|
|
|
|
sg_index = sg - &scb->sg_list[1];
|
|
|
|
|
|
|
|
|
|
return (scb->sg_list_phys + (sg_index * sizeof(*scb->sg_list)));
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index)
|
|
|
|
|
{
|
|
|
|
|
return (ahc->scb_data->hscb_busaddr
|
|
|
|
|
+ (sizeof(struct hardware_scb) * index));
|
|
|
|
|
}
|
|
|
|
|
|
2001-07-18 21:39:48 +00:00
|
|
|
static __inline void
|
|
|
|
|
ahc_sync_scb(struct ahc_softc *ahc, struct scb *scb, int op)
|
|
|
|
|
{
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->scb_data->hscb_dmat,
|
2001-07-18 21:39:48 +00:00
|
|
|
ahc->scb_data->hscb_dmamap,
|
|
|
|
|
/*offset*/(scb->hscb - ahc->hscbs) * sizeof(*scb->hscb),
|
|
|
|
|
/*len*/sizeof(*scb->hscb), op);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_sync_sglist(struct ahc_softc *ahc, struct scb *scb, int op)
|
|
|
|
|
{
|
|
|
|
|
if (scb->sg_count == 0)
|
|
|
|
|
return;
|
|
|
|
|
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->scb_data->sg_dmat, scb->sg_map->sg_dmamap,
|
2001-07-18 21:39:48 +00:00
|
|
|
/*offset*/(scb->sg_list - scb->sg_map->sg_vaddr)
|
|
|
|
|
* sizeof(struct ahc_dma_seg),
|
|
|
|
|
/*len*/sizeof(struct ahc_dma_seg) * scb->sg_count, op);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_targetcmd_offset(struct ahc_softc *ahc, u_int index)
|
|
|
|
|
{
|
|
|
|
|
return (((uint8_t *)&ahc->targetcmds[index]) - ahc->qoutfifo);
|
|
|
|
|
}
|
|
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
/******************************** Debugging ***********************************/
|
|
|
|
|
static __inline char *ahc_name(struct ahc_softc *ahc);
|
|
|
|
|
|
|
|
|
|
static __inline char *
|
|
|
|
|
ahc_name(struct ahc_softc *ahc)
|
|
|
|
|
{
|
|
|
|
|
return (ahc->name);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*********************** Miscelaneous Support Functions ***********************/
|
|
|
|
|
|
2002-04-24 16:58:51 +00:00
|
|
|
static __inline void ahc_update_residual(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
static __inline struct ahc_initiator_tinfo *
|
|
|
|
|
ahc_fetch_transinfo(struct ahc_softc *ahc,
|
|
|
|
|
char channel, u_int our_id,
|
|
|
|
|
u_int remote_id,
|
2001-03-29 00:36:35 +00:00
|
|
|
struct ahc_tmode_tstate **tstate);
|
aic7xxx.reg:
Add a constant for the controller's stack size and the
maximum scsi offset.
aic7xxx.seq:
Style nit. The source is implied to be the destination
unless overridden in an "and" instruction.
Update target mode code for changes in identify seen
sequencer flags.
aic7xxx_pci.c:
Ensure that the PCIERRGENDIS bit is set in the
PCIERRGEN config space register. Perhaps this
is a reason for the spurios parity errors reported
on U160 controllers.
Honor the AHC_NO_BIOS_INIT flag.
Allow PCI interrupt reporting to be disabled,
by clearing the PERRRESEN bit in the command
register. This option is now enabled via a new
softc flag: AHC_DISABLE_PCI_PERR.
Disable SERR and pause the controller prior to performing
our mmapped I/O test. This should handle the case of
controllers that do not "auto-access pause". For legacy
controllers, use SCB ram instead of scratch ram since
the latter may contain settings left over from the BIOS
that we will use if an seeprom is not found.
Make use of new ahc_inl/outl() inlines.
aic7xxx.h:
Reformat a few comments to follow driver style.
Add a controller flags that indicate that a controller
has not been initialized by the BIOS and whether to
disable PCI parity errors..
Remove stack probing softc members.
Add a few more syncrate constants that are useful in speed
fallback calculations.
Add the SHOW_MASKED_ERRORS debug flag.
aic7xxx.h:
aic7xxx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
aic7xxx_inline.h:
Implement ahc_[in|out][w|l|q]. This removes the need
for manual 'or and shift" type operations throughout
the driver.
aic7xxx.c:
Move SELTO dignostic so that the SCB is still valid
when we use it for printing path information.
If we are narrow, limit syncrate to Ultra2.
Don't clobber ppr_options when forcing a renegotiation.
The current ppr_options may be referenced while queuing
new commands. Don't set our width to unknown when forcing
negotiation on narrow controllers. This will confuse the
negotiation code into negotiating with a wide message on
narrow controllers.
Add an "asserting atn" diagnostic with controller/target
information.
Remove the probe_stack code. The stack is always
4 deep on legacy controllers, so probing is pointless.
This also avoids an issue where probing the stack would
upset the aic7770.
In ahc_reset(), record whether or not we found the
controller in a reset state. If the controller was
already reset, assume that no BIOS has initialized
the controller and ignore left over scratch ram
settings.
Fix an ifdef bug that caused sequencer debugging to
be enabled always.
Clear the ultraenb flag in our tstate during startup.
The ultraenbled'ness of a device is recorded in the user
transfer settings. tstate->ultraenb bitmask indicates
which devices we have negotiated an ultra speed with.
Just after initialization, we are async. Setting the
ultraenb flag while async seems to be harmless, but it
was confusing to see the ULTRAENB flag set in the SCB.
Enhance residual diagnostic to indicate if the residual
if for sense information or normal data transfers.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
In ahc_dump_card_state() fix a logic reversal. The
SCSIPHASE register only exists on U160 controllers.
The SCSISIGI register exists on all controllers. Not
the other way around. Also print out the ERROR register.
Allow ahc_dump_card_state() to be called when the sequencer
is not paused. Add dump card state markers as in the U320
driver.
2003-01-20 20:44:55 +00:00
|
|
|
static __inline uint16_t
|
|
|
|
|
ahc_inw(struct ahc_softc *ahc, u_int port);
|
|
|
|
|
static __inline void ahc_outw(struct ahc_softc *ahc, u_int port,
|
|
|
|
|
u_int value);
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_inl(struct ahc_softc *ahc, u_int port);
|
|
|
|
|
static __inline void ahc_outl(struct ahc_softc *ahc, u_int port,
|
|
|
|
|
uint32_t value);
|
|
|
|
|
static __inline uint64_t
|
|
|
|
|
ahc_inq(struct ahc_softc *ahc, u_int port);
|
|
|
|
|
static __inline void ahc_outq(struct ahc_softc *ahc, u_int port,
|
|
|
|
|
uint64_t value);
|
2000-09-16 20:02:28 +00:00
|
|
|
static __inline struct scb*
|
|
|
|
|
ahc_get_scb(struct ahc_softc *ahc);
|
|
|
|
|
static __inline void ahc_free_scb(struct ahc_softc *ahc, struct scb *scb);
|
2000-11-06 20:05:38 +00:00
|
|
|
static __inline void ahc_swap_with_next_hscb(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
static __inline void ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb);
|
2001-01-09 00:40:38 +00:00
|
|
|
static __inline struct scsi_sense_data *
|
|
|
|
|
ahc_get_sense_buf(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb);
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_get_sense_bufaddr(struct ahc_softc *ahc,
|
|
|
|
|
struct scb *scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Determine whether the sequencer reported a residual
|
|
|
|
|
* for this SCB/transaction.
|
|
|
|
|
*/
|
2001-05-15 19:41:12 +00:00
|
|
|
static __inline void
|
2002-04-24 16:58:51 +00:00
|
|
|
ahc_update_residual(struct ahc_softc *ahc, struct scb *scb)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
2001-05-15 19:41:12 +00:00
|
|
|
uint32_t sgptr;
|
2000-09-16 20:02:28 +00:00
|
|
|
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
sgptr = aic_le32toh(scb->hscb->sgptr);
|
2001-05-15 19:41:12 +00:00
|
|
|
if ((sgptr & SG_RESID_VALID) != 0)
|
2002-04-24 16:58:51 +00:00
|
|
|
ahc_calc_residual(ahc, scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Return pointers to the transfer negotiation information
|
|
|
|
|
* for the specified our_id/remote_id pair.
|
|
|
|
|
*/
|
|
|
|
|
static __inline struct ahc_initiator_tinfo *
|
|
|
|
|
ahc_fetch_transinfo(struct ahc_softc *ahc, char channel, u_int our_id,
|
2001-03-29 00:36:35 +00:00
|
|
|
u_int remote_id, struct ahc_tmode_tstate **tstate)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
|
|
|
|
/*
|
|
|
|
|
* Transfer data structures are stored from the perspective
|
|
|
|
|
* of the target role. Since the parameters for a connection
|
|
|
|
|
* in the initiator role to a given target are the same as
|
|
|
|
|
* when the roles are reversed, we pretend we are the target.
|
|
|
|
|
*/
|
|
|
|
|
if (channel == 'B')
|
|
|
|
|
our_id += 8;
|
|
|
|
|
*tstate = ahc->enabled_targets[our_id];
|
|
|
|
|
return (&(*tstate)->transinfo[remote_id]);
|
|
|
|
|
}
|
|
|
|
|
|
aic7xxx.reg:
Add a constant for the controller's stack size and the
maximum scsi offset.
aic7xxx.seq:
Style nit. The source is implied to be the destination
unless overridden in an "and" instruction.
Update target mode code for changes in identify seen
sequencer flags.
aic7xxx_pci.c:
Ensure that the PCIERRGENDIS bit is set in the
PCIERRGEN config space register. Perhaps this
is a reason for the spurios parity errors reported
on U160 controllers.
Honor the AHC_NO_BIOS_INIT flag.
Allow PCI interrupt reporting to be disabled,
by clearing the PERRRESEN bit in the command
register. This option is now enabled via a new
softc flag: AHC_DISABLE_PCI_PERR.
Disable SERR and pause the controller prior to performing
our mmapped I/O test. This should handle the case of
controllers that do not "auto-access pause". For legacy
controllers, use SCB ram instead of scratch ram since
the latter may contain settings left over from the BIOS
that we will use if an seeprom is not found.
Make use of new ahc_inl/outl() inlines.
aic7xxx.h:
Reformat a few comments to follow driver style.
Add a controller flags that indicate that a controller
has not been initialized by the BIOS and whether to
disable PCI parity errors..
Remove stack probing softc members.
Add a few more syncrate constants that are useful in speed
fallback calculations.
Add the SHOW_MASKED_ERRORS debug flag.
aic7xxx.h:
aic7xxx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
aic7xxx_inline.h:
Implement ahc_[in|out][w|l|q]. This removes the need
for manual 'or and shift" type operations throughout
the driver.
aic7xxx.c:
Move SELTO dignostic so that the SCB is still valid
when we use it for printing path information.
If we are narrow, limit syncrate to Ultra2.
Don't clobber ppr_options when forcing a renegotiation.
The current ppr_options may be referenced while queuing
new commands. Don't set our width to unknown when forcing
negotiation on narrow controllers. This will confuse the
negotiation code into negotiating with a wide message on
narrow controllers.
Add an "asserting atn" diagnostic with controller/target
information.
Remove the probe_stack code. The stack is always
4 deep on legacy controllers, so probing is pointless.
This also avoids an issue where probing the stack would
upset the aic7770.
In ahc_reset(), record whether or not we found the
controller in a reset state. If the controller was
already reset, assume that no BIOS has initialized
the controller and ignore left over scratch ram
settings.
Fix an ifdef bug that caused sequencer debugging to
be enabled always.
Clear the ultraenb flag in our tstate during startup.
The ultraenbled'ness of a device is recorded in the user
transfer settings. tstate->ultraenb bitmask indicates
which devices we have negotiated an ultra speed with.
Just after initialization, we are async. Setting the
ultraenb flag while async seems to be harmless, but it
was confusing to see the ULTRAENB flag set in the SCB.
Enhance residual diagnostic to indicate if the residual
if for sense information or normal data transfers.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
In ahc_dump_card_state() fix a logic reversal. The
SCSIPHASE register only exists on U160 controllers.
The SCSISIGI register exists on all controllers. Not
the other way around. Also print out the ERROR register.
Allow ahc_dump_card_state() to be called when the sequencer
is not paused. Add dump card state markers as in the U320
driver.
2003-01-20 20:44:55 +00:00
|
|
|
static __inline uint16_t
|
|
|
|
|
ahc_inw(struct ahc_softc *ahc, u_int port)
|
|
|
|
|
{
|
|
|
|
|
return ((ahc_inb(ahc, port+1) << 8) | ahc_inb(ahc, port));
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_outw(struct ahc_softc *ahc, u_int port, u_int value)
|
|
|
|
|
{
|
|
|
|
|
ahc_outb(ahc, port, value & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+1, (value >> 8) & 0xFF);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_inl(struct ahc_softc *ahc, u_int port)
|
|
|
|
|
{
|
|
|
|
|
return ((ahc_inb(ahc, port))
|
|
|
|
|
| (ahc_inb(ahc, port+1) << 8)
|
|
|
|
|
| (ahc_inb(ahc, port+2) << 16)
|
|
|
|
|
| (ahc_inb(ahc, port+3) << 24));
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_outl(struct ahc_softc *ahc, u_int port, uint32_t value)
|
|
|
|
|
{
|
|
|
|
|
ahc_outb(ahc, port, (value) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+1, ((value) >> 8) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+2, ((value) >> 16) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+3, ((value) >> 24) & 0xFF);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint64_t
|
|
|
|
|
ahc_inq(struct ahc_softc *ahc, u_int port)
|
|
|
|
|
{
|
|
|
|
|
return ((ahc_inb(ahc, port))
|
|
|
|
|
| (ahc_inb(ahc, port+1) << 8)
|
|
|
|
|
| (ahc_inb(ahc, port+2) << 16)
|
|
|
|
|
| (ahc_inb(ahc, port+3) << 24)
|
|
|
|
|
| (((uint64_t)ahc_inb(ahc, port+4)) << 32)
|
|
|
|
|
| (((uint64_t)ahc_inb(ahc, port+5)) << 40)
|
|
|
|
|
| (((uint64_t)ahc_inb(ahc, port+6)) << 48)
|
|
|
|
|
| (((uint64_t)ahc_inb(ahc, port+7)) << 56));
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_outq(struct ahc_softc *ahc, u_int port, uint64_t value)
|
|
|
|
|
{
|
|
|
|
|
ahc_outb(ahc, port, value & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+1, (value >> 8) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+2, (value >> 16) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+3, (value >> 24) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+4, (value >> 32) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+5, (value >> 40) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+6, (value >> 48) & 0xFF);
|
|
|
|
|
ahc_outb(ahc, port+7, (value >> 56) & 0xFF);
|
|
|
|
|
}
|
|
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
/*
|
|
|
|
|
* Get a free scb. If there are none, see if we can allocate a new SCB.
|
|
|
|
|
*/
|
|
|
|
|
static __inline struct scb *
|
|
|
|
|
ahc_get_scb(struct ahc_softc *ahc)
|
|
|
|
|
{
|
2000-10-05 04:24:14 +00:00
|
|
|
struct scb *scb;
|
2000-09-16 20:02:28 +00:00
|
|
|
|
2000-10-05 04:24:14 +00:00
|
|
|
if ((scb = SLIST_FIRST(&ahc->scb_data->free_scbs)) == NULL) {
|
2007-04-19 18:53:52 +00:00
|
|
|
if (ahc_alloc_scbs(ahc) == 0)
|
|
|
|
|
return (NULL);
|
2000-10-05 04:24:14 +00:00
|
|
|
scb = SLIST_FIRST(&ahc->scb_data->free_scbs);
|
|
|
|
|
if (scb == NULL)
|
|
|
|
|
return (NULL);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
2000-10-05 04:24:14 +00:00
|
|
|
SLIST_REMOVE_HEAD(&ahc->scb_data->free_scbs, links.sle);
|
|
|
|
|
return (scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Return an SCB resource to the free list.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_free_scb(struct ahc_softc *ahc, struct scb *scb)
|
|
|
|
|
{
|
|
|
|
|
struct hardware_scb *hscb;
|
|
|
|
|
|
|
|
|
|
hscb = scb->hscb;
|
|
|
|
|
/* Clean up for the next user */
|
2000-10-05 04:24:14 +00:00
|
|
|
ahc->scb_data->scbindex[hscb->tag] = NULL;
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
scb->flags = SCB_FLAG_NONE;
|
2000-09-16 20:02:28 +00:00
|
|
|
hscb->control = 0;
|
|
|
|
|
|
|
|
|
|
SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, scb, links.sle);
|
2000-10-05 04:24:14 +00:00
|
|
|
|
|
|
|
|
/* Notify the OSM that a resource is now available. */
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_platform_scb_free(ahc, scb);
|
2000-10-05 04:24:14 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline struct scb *
|
|
|
|
|
ahc_lookup_scb(struct ahc_softc *ahc, u_int tag)
|
|
|
|
|
{
|
2001-07-18 21:39:48 +00:00
|
|
|
struct scb* scb;
|
2000-10-05 04:24:14 +00:00
|
|
|
|
2001-07-18 21:39:48 +00:00
|
|
|
scb = ahc->scb_data->scbindex[tag];
|
|
|
|
|
if (scb != NULL)
|
|
|
|
|
ahc_sync_scb(ahc, scb,
|
|
|
|
|
BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE);
|
|
|
|
|
return (scb);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
2000-11-06 20:05:38 +00:00
|
|
|
ahc_swap_with_next_hscb(struct ahc_softc *ahc, struct scb *scb)
|
2000-09-16 20:02:28 +00:00
|
|
|
{
|
2000-10-05 04:24:14 +00:00
|
|
|
struct hardware_scb *q_hscb;
|
|
|
|
|
u_int saved_tag;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Our queuing method is a bit tricky. The card
|
|
|
|
|
* knows in advance which HSCB to download, and we
|
|
|
|
|
* can't disappoint it. To achieve this, the next
|
|
|
|
|
* SCB to download is saved off in ahc->next_queued_scb.
|
|
|
|
|
* When we are called to queue "an arbitrary scb",
|
|
|
|
|
* we copy the contents of the incoming HSCB to the one
|
|
|
|
|
* the sequencer knows about, swap HSCB pointers and
|
2000-11-06 20:05:38 +00:00
|
|
|
* finally assign the SCB to the tag indexed location
|
2000-10-05 04:24:14 +00:00
|
|
|
* in the scb_array. This makes sure that we can still
|
|
|
|
|
* locate the correct SCB by SCB_TAG.
|
|
|
|
|
*/
|
|
|
|
|
q_hscb = ahc->next_queued_scb->hscb;
|
|
|
|
|
saved_tag = q_hscb->tag;
|
2000-10-12 14:36:27 +00:00
|
|
|
memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb));
|
aic7xxx.c:
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
2000-10-31 18:43:29 +00:00
|
|
|
if ((scb->flags & SCB_CDB32_PTR) != 0) {
|
|
|
|
|
q_hscb->shared_data.cdb_ptr =
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_htole32(ahc_hscb_busaddr(ahc, q_hscb->tag)
|
2002-04-24 16:58:51 +00:00
|
|
|
+ offsetof(struct hardware_scb, cdb32));
|
aic7xxx.c:
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
2000-10-31 18:43:29 +00:00
|
|
|
}
|
2000-10-05 04:24:14 +00:00
|
|
|
q_hscb->tag = saved_tag;
|
|
|
|
|
q_hscb->next = scb->hscb->tag;
|
|
|
|
|
|
|
|
|
|
/* Now swap HSCB pointers. */
|
|
|
|
|
ahc->next_queued_scb->hscb = scb->hscb;
|
|
|
|
|
scb->hscb = q_hscb;
|
|
|
|
|
|
|
|
|
|
/* Now define the mapping from tag to SCB in the scbindex */
|
|
|
|
|
ahc->scb_data->scbindex[scb->hscb->tag] = scb;
|
2000-11-06 20:05:38 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Tell the sequencer about a new transaction to execute.
|
|
|
|
|
*/
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb)
|
|
|
|
|
{
|
|
|
|
|
ahc_swap_with_next_hscb(ahc, scb);
|
2000-10-05 04:24:14 +00:00
|
|
|
|
aic7xxx.c:
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
2000-10-31 18:43:29 +00:00
|
|
|
if (scb->hscb->tag == SCB_LIST_NULL
|
|
|
|
|
|| scb->hscb->next == SCB_LIST_NULL)
|
|
|
|
|
panic("Attempt to queue invalid SCB tag %x:%x\n",
|
|
|
|
|
scb->hscb->tag, scb->hscb->next);
|
|
|
|
|
|
2003-05-26 21:24:01 +00:00
|
|
|
/*
|
|
|
|
|
* Setup data "oddness".
|
|
|
|
|
*/
|
|
|
|
|
scb->hscb->lun &= LID;
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
if (aic_get_transfer_length(scb) & 0x1)
|
2003-05-26 21:24:01 +00:00
|
|
|
scb->hscb->lun |= SCB_XFERLEN_ODD;
|
|
|
|
|
|
2000-10-05 04:24:14 +00:00
|
|
|
/*
|
|
|
|
|
* Keep a history of SCBs we've downloaded in the qinfifo.
|
|
|
|
|
*/
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag;
|
2001-07-18 21:39:48 +00:00
|
|
|
|
|
|
|
|
/*
|
2003-05-03 23:55:38 +00:00
|
|
|
* Make sure our data is consistent from the
|
2001-07-18 21:39:48 +00:00
|
|
|
* perspective of the adapter.
|
|
|
|
|
*/
|
|
|
|
|
ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
|
|
|
|
|
|
|
|
|
|
/* Tell the adapter about the newly queued SCB */
|
2000-09-16 20:02:28 +00:00
|
|
|
if ((ahc->features & AHC_QUEUE_REGS) != 0) {
|
|
|
|
|
ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext);
|
|
|
|
|
} else {
|
|
|
|
|
if ((ahc->features & AHC_AUTOPAUSE) == 0)
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
ahc_pause(ahc);
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext);
|
|
|
|
|
if ((ahc->features & AHC_AUTOPAUSE) == 0)
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
ahc_unpause(ahc);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
2001-01-09 00:40:38 +00:00
|
|
|
static __inline struct scsi_sense_data *
|
|
|
|
|
ahc_get_sense_buf(struct ahc_softc *ahc, struct scb *scb)
|
|
|
|
|
{
|
|
|
|
|
int offset;
|
|
|
|
|
|
|
|
|
|
offset = scb - ahc->scb_data->scbarray;
|
|
|
|
|
return (&ahc->scb_data->sense[offset]);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline uint32_t
|
|
|
|
|
ahc_get_sense_bufaddr(struct ahc_softc *ahc, struct scb *scb)
|
|
|
|
|
{
|
|
|
|
|
int offset;
|
|
|
|
|
|
|
|
|
|
offset = scb - ahc->scb_data->scbarray;
|
|
|
|
|
return (ahc->scb_data->sense_busaddr
|
|
|
|
|
+ (offset * sizeof(struct scsi_sense_data)));
|
|
|
|
|
}
|
|
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
/************************** Interrupt Processing ******************************/
|
2001-07-18 21:39:48 +00:00
|
|
|
static __inline void ahc_sync_qoutfifo(struct ahc_softc *ahc, int op);
|
|
|
|
|
static __inline void ahc_sync_tqinfifo(struct ahc_softc *ahc, int op);
|
|
|
|
|
static __inline u_int ahc_check_cmdcmpltqueues(struct ahc_softc *ahc);
|
2003-05-03 23:55:38 +00:00
|
|
|
static __inline int ahc_intr(struct ahc_softc *ahc);
|
2001-07-18 21:39:48 +00:00
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_sync_qoutfifo(struct ahc_softc *ahc, int op)
|
|
|
|
|
{
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap,
|
2001-07-18 21:39:48 +00:00
|
|
|
/*offset*/0, /*len*/256, op);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static __inline void
|
|
|
|
|
ahc_sync_tqinfifo(struct ahc_softc *ahc, int op)
|
|
|
|
|
{
|
|
|
|
|
#ifdef AHC_TARGET_MODE
|
|
|
|
|
if ((ahc->flags & AHC_TARGETROLE) != 0) {
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->shared_data_dmat,
|
2001-07-18 21:39:48 +00:00
|
|
|
ahc->shared_data_dmamap,
|
|
|
|
|
ahc_targetcmd_offset(ahc, 0),
|
|
|
|
|
sizeof(struct target_cmd) * AHC_TMODE_CMDS,
|
|
|
|
|
op);
|
|
|
|
|
}
|
|
|
|
|
#endif
|
|
|
|
|
}
|
2000-09-16 20:02:28 +00:00
|
|
|
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
/*
|
|
|
|
|
* See if the firmware has posted any completed commands
|
|
|
|
|
* into our in-core command complete fifos.
|
|
|
|
|
*/
|
|
|
|
|
#define AHC_RUN_QOUTFIFO 0x1
|
|
|
|
|
#define AHC_RUN_TQINFIFO 0x2
|
|
|
|
|
static __inline u_int
|
|
|
|
|
ahc_check_cmdcmpltqueues(struct ahc_softc *ahc)
|
|
|
|
|
{
|
|
|
|
|
u_int retval;
|
|
|
|
|
|
|
|
|
|
retval = 0;
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap,
|
2001-07-18 21:39:48 +00:00
|
|
|
/*offset*/ahc->qoutfifonext, /*len*/1,
|
|
|
|
|
BUS_DMASYNC_POSTREAD);
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
if (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL)
|
|
|
|
|
retval |= AHC_RUN_QOUTFIFO;
|
|
|
|
|
#ifdef AHC_TARGET_MODE
|
2002-04-24 16:58:51 +00:00
|
|
|
if ((ahc->flags & AHC_TARGETROLE) != 0
|
|
|
|
|
&& (ahc->flags & AHC_TQINFIFO_BLOCKED) == 0) {
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
aic_dmamap_sync(ahc, ahc->shared_data_dmat,
|
2001-07-18 21:39:48 +00:00
|
|
|
ahc->shared_data_dmamap,
|
|
|
|
|
ahc_targetcmd_offset(ahc, ahc->tqinfifofnext),
|
|
|
|
|
/*len*/sizeof(struct target_cmd),
|
|
|
|
|
BUS_DMASYNC_POSTREAD);
|
|
|
|
|
if (ahc->targetcmds[ahc->tqinfifonext].cmd_valid != 0)
|
|
|
|
|
retval |= AHC_RUN_TQINFIFO;
|
|
|
|
|
}
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
#endif
|
|
|
|
|
return (retval);
|
|
|
|
|
}
|
|
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
/*
|
|
|
|
|
* Catch an interrupt from the adapter
|
|
|
|
|
*/
|
2003-05-03 23:55:38 +00:00
|
|
|
static __inline int
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc_intr(struct ahc_softc *ahc)
|
|
|
|
|
{
|
|
|
|
|
u_int intstat;
|
|
|
|
|
|
2002-08-31 06:46:37 +00:00
|
|
|
if ((ahc->pause & INTEN) == 0) {
|
|
|
|
|
/*
|
|
|
|
|
* Our interrupt is not enabled on the chip
|
|
|
|
|
* and may be disabled for re-entrancy reasons,
|
|
|
|
|
* so just return. This is likely just a shared
|
|
|
|
|
* interrupt.
|
|
|
|
|
*/
|
2003-05-03 23:55:38 +00:00
|
|
|
return (0);
|
2002-08-31 06:46:37 +00:00
|
|
|
}
|
2000-09-16 20:02:28 +00:00
|
|
|
/*
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
* Instead of directly reading the interrupt status register,
|
|
|
|
|
* infer the cause of the interrupt by checking our in-core
|
|
|
|
|
* completion queues. This avoids a costly PCI bus read in
|
|
|
|
|
* most cases.
|
2000-09-16 20:02:28 +00:00
|
|
|
*/
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
if ((ahc->flags & (AHC_ALL_INTERRUPTS|AHC_EDGE_INTERRUPT)) == 0
|
2002-04-24 16:58:51 +00:00
|
|
|
&& (ahc_check_cmdcmpltqueues(ahc) != 0))
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
intstat = CMDCMPLT;
|
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
2001-03-11 06:34:17 +00:00
|
|
|
else {
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
intstat = ahc_inb(ahc, INTSTAT);
|
|
|
|
|
}
|
|
|
|
|
|
2003-05-03 23:55:38 +00:00
|
|
|
if ((intstat & INT_PEND) == 0) {
|
ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
2003-12-17 00:02:10 +00:00
|
|
|
#if AIC_PCI_CONFIG > 0
|
2003-05-03 23:55:38 +00:00
|
|
|
if (ahc->unsolicited_ints > 500) {
|
|
|
|
|
ahc->unsolicited_ints = 0;
|
|
|
|
|
if ((ahc->chip & AHC_PCI) != 0
|
|
|
|
|
&& (ahc_inb(ahc, ERROR) & PCIERRSTAT) != 0)
|
|
|
|
|
ahc->bus_intr(ahc);
|
|
|
|
|
}
|
|
|
|
|
#endif
|
|
|
|
|
ahc->unsolicited_ints++;
|
|
|
|
|
return (0);
|
|
|
|
|
}
|
|
|
|
|
ahc->unsolicited_ints = 0;
|
|
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
if (intstat & CMDCMPLT) {
|
|
|
|
|
ahc_outb(ahc, CLRINT, CLRCMDINT);
|
ahc_eisa.c:
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
2000-12-20 01:11:37 +00:00
|
|
|
|
2000-09-16 20:02:28 +00:00
|
|
|
/*
|
|
|
|
|
* Ensure that the chip sees that we've cleared
|
|
|
|
|
* this interrupt before we walk the output fifo.
|
|
|
|
|
* Otherwise, we may, due to posted bus writes,
|
|
|
|
|
* clear the interrupt after we finish the scan,
|
|
|
|
|
* and after the sequencer has added new entries
|
|
|
|
|
* and asserted the interrupt again.
|
|
|
|
|
*/
|
|
|
|
|
ahc_flush_device_writes(ahc);
|
2002-04-24 16:58:51 +00:00
|
|
|
ahc_run_qoutfifo(ahc);
|
2000-09-16 20:02:28 +00:00
|
|
|
#ifdef AHC_TARGET_MODE
|
2002-04-24 16:58:51 +00:00
|
|
|
if ((ahc->flags & AHC_TARGETROLE) != 0)
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc_run_tqinfifo(ahc, /*paused*/FALSE);
|
|
|
|
|
#endif
|
|
|
|
|
}
|
2001-07-18 21:39:48 +00:00
|
|
|
|
2003-05-03 23:55:38 +00:00
|
|
|
/*
|
|
|
|
|
* Handle statuses that may invalidate our cached
|
|
|
|
|
* copy of INTSTAT separately.
|
|
|
|
|
*/
|
|
|
|
|
if (intstat == 0xFF && (ahc->features & AHC_REMOVABLE) != 0) {
|
|
|
|
|
/* Hot eject. Do nothing */
|
|
|
|
|
} else if (intstat & BRKADRINT) {
|
2000-09-16 20:02:28 +00:00
|
|
|
ahc_handle_brkadrint(ahc);
|
2003-05-03 23:55:38 +00:00
|
|
|
} else if ((intstat & (SEQINT|SCSIINT)) != 0) {
|
2000-09-16 20:02:28 +00:00
|
|
|
|
|
|
|
|
ahc_pause_bug_fix(ahc);
|
|
|
|
|
|
2003-05-03 23:55:38 +00:00
|
|
|
if ((intstat & SEQINT) != 0)
|
|
|
|
|
ahc_handle_seqint(ahc, intstat);
|
2000-09-16 20:02:28 +00:00
|
|
|
|
2003-05-03 23:55:38 +00:00
|
|
|
if ((intstat & SCSIINT) != 0)
|
|
|
|
|
ahc_handle_scsiint(ahc, intstat);
|
|
|
|
|
}
|
|
|
|
|
return (1);
|
2000-09-16 20:02:28 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#endif /* _AIC7XXX_INLINE_H_ */
|
