d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
54aa1adf6c
freebsd-skq/sys/dev/mk48txx/mk48txxreg.h

157 lines
6.1 KiB
C
Raw Normal View History

Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
/*-
* Copyright (c) 2000 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Paul Kranenburg.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
Remove clause 3 and 4 from TNF licenses. Obtained from: NetBSD
2009-12-25 21:41:05 +00:00
* $NetBSD: mk48txxreg.h,v 1.10 2008/04/28 20:23:50 martin Exp $
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
*
* $FreeBSD$
*/
/*
* Mostek MK48Txx clocks.
*
* The MK48T02 has 2KB of non-volatile memory. The time-of-day clock
* registers start at offset 0x7f8.
*
o Sync with the NetBSD mk48txx driver (the result simplyfies some changes I have in mind for the genclock interface): - Recognize the MK48T18 as well (differs from the MK48T08 only in packaging options and voltages). - Allow MD code to provide functions for reading/writing NVRAM/RTC locations. If passed NULL, the old behaviour using bus_space_{read,write}_1() is used. Otherwise, all access to the chip goes via the MD functions. This is necessary for mvmeppc boards where the mk48txx NVRAM/RTC is not directly addressable. - Cleanup MI mk48txx(4) todclock driver: - Prepare mk48txxvar.h and leave only register definitions in mk48txxreg.h. - Define struct mk48txx_softc as usual devices and allocate necessary members in it. - Change mk48txx_attach() to only take a device_t. o While converting the sparc64 eeprom driver to the above changes: - Remove some dead code and stale comments. - Use the NVRAM size provided by the mk48txx driver instead of hardcoding it as suggested by a comment. - Add a comment about why it doesn't make much sense to read the hostid directly from the NVRAM except for displaying it when attaching. - Don't print the hostid if it reads all zero because it's stored elsewhere.
2004-11-17 12:54:12 +00:00
* The MK48T08 and MK48T18 have 8KB of non-volatile memory
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
*
* The MK48T59 also has 8KB of non-volatile memory but in addition it
* has a battery low detection bit and a power supply wakeup alarm for
* power management. It's at offset 0x1ff0 in the NVRAM.
*/
/*
* Mostek MK48TXX register definitions
*/
/*
* The first bank of eight registers at offset (nvramsz - 16) is
* available only on recenter (which?) MK48Txx models.
*/
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_FLAGS 0 /* flags register */
#define MK48TXX_UNUSED 1 /* unused */
#define MK48TXX_ASEC 2 /* alarm seconds (0..59; BCD) */
#define MK48TXX_AMIN 3 /* alarm minutes (0..59; BCD) */
#define MK48TXX_AHOUR 4 /* alarm hours (0..23; BCD) */
#define MK48TXX_ADAY 5 /* alarm day in month (1..31; BCD) */
#define MK48TXX_INTR 6 /* interrupts register */
#define MK48TXX_WDOG 7 /* watchdog register */
#define MK48TXX_ICSR 8 /* control register */
#define MK48TXX_ISEC 9 /* seconds (0..59; BCD) */
#define MK48TXX_IMIN 10 /* minutes (0..59; BCD) */
#define MK48TXX_IHOUR 11 /* hours (0..23; BCD) */
#define MK48TXX_IWDAY 12 /* weekday (1..7) */
#define MK48TXX_IDAY 13 /* day in month (1..31; BCD) */
#define MK48TXX_IMON 14 /* month (1..12; BCD) */
#define MK48TXX_IYEAR 15 /* year (0..99; BCD) */
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/*
* Note that some of the bits below that are not in the first eight
* registers are also only available on models with an extended
* register set.
*/
/* Bits in the flags register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_FLAGS_BL 0x10 /* battery low (read only) */
#define MK48TXX_FLAGS_AF 0x40 /* alarm flag (read only) */
#define MK48TXX_FLAGS_WDF 0x80 /* watchdog flag (read only) */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the alarm seconds register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_ASEC_MASK 0x7f /* mask for alarm seconds */
#define MK48TXX_ASEC_RPT1 0x80 /* alarm repeat mode bit 1 */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the alarm minutes register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_AMIN_MASK 0x7f /* mask for alarm minutes */
#define MK48TXX_AMIN_RPT2 0x80 /* alarm repeat mode bit 2 */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the alarm hours register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_AHOUR_MASK 0x3f /* mask for alarm hours */
#define MK48TXX_AHOUR_RPT3 0x80 /* alarm repeat mode bit 3 */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the alarm day in month register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_ADAY_MASK 0x3f /* mask for alarm day in month */
#define MK48TXX_ADAY_RPT4 0x80 /* alarm repeat mode bit 4 */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the interrupts register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_INTR_ABE 0x20 /* alarm in battery back-up mode */
#define MK48TXX_INTR_AFE 0x80 /* alarm flag enable */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the watchdog register (extended only) */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_WDOG_RB_1_16 0x00 /* watchdog resolution 1/16 second */
#define MK48TXX_WDOG_RB_1_4 0x01 /* watchdog resolution 1/4 second */
#define MK48TXX_WDOG_RB_1 0x02 /* watchdog resolution 1 second */
#define MK48TXX_WDOG_RB_4 0x03 /* watchdog resolution 4 seconds */
#define MK48TXX_WDOG_BMB_MASK 0x7c /* mask for watchdog multiplier */
#define MK48TXX_WDOG_BMB_SHIFT 2 /* shift for watchdog multiplier */
#define MK48TXX_WDOG_WDS 0x80 /* watchdog steering bit */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
/* Bits in the control register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_CSR_CALIB_MASK 0x1f /* mask for calibration step width */
#define MK48TXX_CSR_SIGN 0x20 /* sign of above calibration witdh */
#define MK48TXX_CSR_READ 0x40 /* want to read (freeze clock) */
#define MK48TXX_CSR_WRITE 0x80 /* want to write */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the seconds register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_SEC_MASK 0x7f /* mask for seconds */
#define MK48TXX_SEC_ST 0x80 /* stop oscillator */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the minutes register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_MIN_MASK 0x7f /* mask for minutes */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the hours register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_HOUR_MASK 0x3f /* mask for hours */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the century/weekday register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_WDAY_MASK 0x07 /* mask for weekday */
#define MK48TXX_WDAY_CB 0x10 /* century bit (extended only) */
#define MK48TXX_WDAY_CB_SHIFT 4 /* shift for century bit */
#define MK48TXX_WDAY_CEB 0x20 /* century enable bit (extended only) */
#define MK48TXX_WDAY_FT 0x40 /* frequency test */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the day in month register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_DAY_MASK 0x3f /* mask for day in month */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the month register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_MON_MASK 0x1f /* mask for month */
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Bits in the year register */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48TXX_YEAR_MASK 0xff /* mask for year */
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
- Some of the upper bits of the time related (seconds, minutes, etc.) registers are control bits or depending on the model contain additional time bits with a different meaning than the lower ones. In order to only read the desired time bits and not change the upper bits on write use appropriate masks in the gettime and settime function respectively. Due to the polarity of the stop oscillator bit and the fact that the century bits aren't used on sparc64 not masking them didn't cause problems so far. - Fix two off-by-one errors in the handling of the day of week. The genclock code represents the dow as 0 - 6 with 0 being Sunday but the mk48txx use 1 - 7 with 1 being Sunday. In the settime function when writing the dow to the clock the range wasn't adjusted accordingly but the clock apparently played along nicely otherwise the second bug in the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning Saturday would have been triggered. Fixing these makes the date being stored in the same format Sun/Solaris uses and cures the "Invalid time in real time clock. Check and reset the date immediately!" when the date was set under Solaris prior to booting FreeBSD/sparc64. [1] Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug", i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to be common but might be on purpose for compatibility when multi-booting with other OS which do the same. So it might make sense to add a flag to handle the dow off-by-one for use of this driver on platforms other than sparc64. - Check the state of the battery on mk48txx that support this in the attach function. - Add a note that use of the century bit should be implemented but isn't required at the moment because it isn't used on sparc64. Problem noted by: joerg [1] MT5 candidate.
2004-09-19 21:38:11 +00:00
/* Model specific NVRAM sizes and clock offsets */
Style changes
2009-12-25 21:32:26 +00:00
#define MK48T02_CLKSZ 2048
#define MK48T02_CLKOFF 0x7f0
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
Style changes
2009-12-25 21:32:26 +00:00
#define MK48T08_CLKSZ 8192
#define MK48T08_CLKOFF 0x1ff0
Add a driver back end for the Mostek MK48T02, MK48T08 and MK48T59 time-of-day clocks, ported from NetBSD. The front-ends are expected to be at least partly machine-dependent; the sparc64 EBus and SBus ones will be commited to MD directories for now (in a subsequent commit).
2002-04-04 23:44:42 +00:00
Style changes
2009-12-25 21:32:26 +00:00
#define MK48T18_CLKSZ 8192
#define MK48T18_CLKOFF 0x1ff0
o Sync with the NetBSD mk48txx driver (the result simplyfies some changes I have in mind for the genclock interface): - Recognize the MK48T18 as well (differs from the MK48T08 only in packaging options and voltages). - Allow MD code to provide functions for reading/writing NVRAM/RTC locations. If passed NULL, the old behaviour using bus_space_{read,write}_1() is used. Otherwise, all access to the chip goes via the MD functions. This is necessary for mvmeppc boards where the mk48txx NVRAM/RTC is not directly addressable. - Cleanup MI mk48txx(4) todclock driver: - Prepare mk48txxvar.h and leave only register definitions in mk48txxreg.h. - Define struct mk48txx_softc as usual devices and allocate necessary members in it. - Change mk48txx_attach() to only take a device_t. o While converting the sparc64 eeprom driver to the above changes: - Remove some dead code and stale comments. - Use the NVRAM size provided by the mk48txx driver instead of hardcoding it as suggested by a comment. - Add a comment about why it doesn't make much sense to read the hostid directly from the NVRAM except for displaying it when attaching. - Don't print the hostid if it reads all zero because it's stored elsewhere.
2004-11-17 12:54:12 +00:00
Style changes
2009-12-25 21:32:26 +00:00
#define MK48T59_CLKSZ 8192
#define MK48T59_CLKOFF 0x1ff0
Reference in New Issue Copy Permalink