d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
70aad3bf07
freebsd-skq/sys/mips/nlm/hal/sys.h

160 lines
5.1 KiB
C
Raw Normal View History

Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
/*-
* Copyright 2003-2011 Netlogic Microsystems (Netlogic). All rights
* reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
*
* THIS SOFTWARE IS PROVIDED BY Netlogic Microsystems ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL NETLOGIC OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
* NETLOGIC_BSD
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
* $FreeBSD$
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
*/
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
#ifndef __NLM_HAL_SYS_H__
Support for XLP4xx and XLP 8xx B0 revision - Add 4xx processor IDs, add workaround in CPU detection code. - Update frequency detection code for XLP 8xx. - Add setting device frequency code. - Update processor ID checking code.
2012-03-27 07:39:05 +00:00
#define __NLM_HAL_SYS_H__
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
/**
* @file_name sys.h
* @author Netlogic Microsystems
* @brief HAL for System configuration registers
*/
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
#define SYS_CHIP_RESET 0x00
#define SYS_POWER_ON_RESET_CFG 0x01
#define SYS_EFUSE_DEVICE_CFG_STATUS0 0x02
#define SYS_EFUSE_DEVICE_CFG_STATUS1 0x03
#define SYS_EFUSE_DEVICE_CFG_STATUS2 0x04
#define SYS_EFUSE_DEVICE_CFG3 0x05
#define SYS_EFUSE_DEVICE_CFG4 0x06
#define SYS_EFUSE_DEVICE_CFG5 0x07
#define SYS_EFUSE_DEVICE_CFG6 0x08
#define SYS_EFUSE_DEVICE_CFG7 0x09
#define SYS_PLL_CTRL 0x0a
#define SYS_CPU_RESET 0x0b
#define SYS_CPU_NONCOHERENT_MODE 0x0d
#define SYS_CORE_DFS_DIS_CTRL 0x0e
#define SYS_CORE_DFS_RST_CTRL 0x0f
#define SYS_CORE_DFS_BYP_CTRL 0x10
#define SYS_CORE_DFS_PHA_CTRL 0x11
#define SYS_CORE_DFS_DIV_INC_CTRL 0x12
#define SYS_CORE_DFS_DIV_DEC_CTRL 0x13
#define SYS_CORE_DFS_DIV_VALUE 0x14
#define SYS_RESET 0x15
#define SYS_DFS_DIS_CTRL 0x16
#define SYS_DFS_RST_CTRL 0x17
#define SYS_DFS_BYP_CTRL 0x18
#define SYS_DFS_DIV_INC_CTRL 0x19
#define SYS_DFS_DIV_DEC_CTRL 0x1a
#define SYS_DFS_DIV_VALUE0 0x1b
#define SYS_DFS_DIV_VALUE1 0x1c
#define SYS_SENSE_AMP_DLY 0x1d
#define SYS_SOC_SENSE_AMP_DLY 0x1e
#define SYS_CTRL0 0x1f
#define SYS_CTRL1 0x20
#define SYS_TIMEOUT_BS1 0x21
#define SYS_BYTE_SWAP 0x22
#define SYS_VRM_VID 0x23
#define SYS_PWR_RAM_CMD 0x24
#define SYS_PWR_RAM_ADDR 0x25
#define SYS_PWR_RAM_DATA0 0x26
#define SYS_PWR_RAM_DATA1 0x27
#define SYS_PWR_RAM_DATA2 0x28
#define SYS_PWR_UCODE 0x29
#define SYS_CPU0_PWR_STATUS 0x2a
#define SYS_CPU1_PWR_STATUS 0x2b
#define SYS_CPU2_PWR_STATUS 0x2c
#define SYS_CPU3_PWR_STATUS 0x2d
#define SYS_CPU4_PWR_STATUS 0x2e
#define SYS_CPU5_PWR_STATUS 0x2f
#define SYS_CPU6_PWR_STATUS 0x30
#define SYS_CPU7_PWR_STATUS 0x31
#define SYS_STATUS 0x32
#define SYS_INT_POL 0x33
#define SYS_INT_TYPE 0x34
#define SYS_INT_STATUS 0x35
#define SYS_INT_MASK0 0x36
#define SYS_INT_MASK1 0x37
#define SYS_UCO_S_ECC 0x38
#define SYS_UCO_M_ECC 0x39
#define SYS_UCO_ADDR 0x3a
Netlogic XLP network driver update Changes are to - update board and network interface detection logic - fix reading onboard CPLD in little-endian config - print NAE frequency conrrectly for Bx chips - update XAUI config to disable Rx/Tx until interface is up Submitted by: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
2013-09-07 18:26:16 +00:00
#define SYS_PLL_DFS_BYP_CTRL 0x3a /* Bx stepping */
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
#define SYS_UCO_INSTR 0x3b
#define SYS_MEM_BIST0 0x3c
#define SYS_MEM_BIST1 0x3d
Netlogic XLP network driver update Changes are to - update board and network interface detection logic - fix reading onboard CPLD in little-endian config - print NAE frequency conrrectly for Bx chips - update XAUI config to disable Rx/Tx until interface is up Submitted by: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
2013-09-07 18:26:16 +00:00
#define SYS_PLL_DFS_DIV_VALUE 0x3d /* Bx stepping */
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
#define SYS_MEM_BIST2 0x3e
#define SYS_MEM_BIST3 0x3f
#define SYS_MEM_BIST4 0x40
#define SYS_MEM_BIST5 0x41
#define SYS_MEM_BIST6 0x42
#define SYS_MEM_BIST7 0x43
#define SYS_MEM_BIST8 0x44
#define SYS_MEM_BIST9 0x45
#define SYS_MEM_BIST10 0x46
#define SYS_MEM_BIST11 0x47
#define SYS_MEM_BIST12 0x48
#define SYS_SCRTCH0 0x49
#define SYS_SCRTCH1 0x4a
#define SYS_SCRTCH2 0x4b
#define SYS_SCRTCH3 0x4c
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
#if !defined(LOCORE) && !defined(__ASSEMBLY__)
MIPS XLP platform code update. * Update the hardware access register definitions and functions to bring them in line with other Netlogic software. * Update the platform bus to use PCI even for on-chip devices. Add a dummy PCI driver to ignore on-chip devices which do not need driver. * Provide memory and IRQ resource allocation code for on-chip devices which cannot get it from PCI config. * add support for on-chip PCI and USB interfaces. * update conf files, enable pci and retain old MAXCPU until we can support >32 cpus. Approved by: re(kib), jmallett
2011-09-05 10:45:29 +00:00
#define nlm_read_sys_reg(b, r) nlm_read_reg(b, r)
#define nlm_write_sys_reg(b, r, v) nlm_write_reg(b, r, v)
#define nlm_get_sys_pcibase(node) nlm_pcicfg_base(XLP_IO_SYS_OFFSET(node))
#define nlm_get_sys_regbase(node) (nlm_get_sys_pcibase(node) + XLP_IO_PCI_HDRSZ)
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
Support for XLP4xx and XLP 8xx B0 revision - Add 4xx processor IDs, add workaround in CPU detection code. - Update frequency detection code for XLP 8xx. - Add setting device frequency code. - Update processor ID checking code.
2012-03-27 07:39:05 +00:00
enum {
/* Don't change order and it must start from zero */
DFS_DEVICE_NAE = 0,
DFS_DEVICE_SAE,
DFS_DEVICE_RSA,
DFS_DEVICE_DTRE,
DFS_DEVICE_CMP,
DFS_DEVICE_KBP,
DFS_DEVICE_DMC,
DFS_DEVICE_NAND,
DFS_DEVICE_MMC,
DFS_DEVICE_NOR,
DFS_DEVICE_CORE,
DFS_DEVICE_REGEX_SLOW,
DFS_DEVICE_REGEX_FAST,
DFS_DEVICE_SATA,
INVALID_DFS_DEVICE = 0xFF
};
Broadcom XLP updates for the new firmware Support few more versions of board firmware. In case the security block is disabled, enable it at boot. Also increase the excluded memory region to cover the area used by the firmware to initialize devices.
2013-01-24 14:33:25 +00:00
static __inline
void nlm_sys_enable_block(uint64_t sys_base, int block)
{
uint32_t dfsdis, mask;
mask = 1 << block;
dfsdis = nlm_read_sys_reg(sys_base, SYS_DFS_DIS_CTRL);
if ((dfsdis & mask) == 0)
return; /* already enabled, nothing to do */
dfsdis &= ~mask;
nlm_write_sys_reg(sys_base, SYS_DFS_DIS_CTRL, dfsdis);
}
Add MIPS platform files for Netlogic XLP SoC. Processor, UART, PIC and Messaging Network code. Also add sys/mips/nlm/hal for on-chip device registers. In collaboration with: Prabhath Raman <prabhathpr at netlogicmicro com> Approved by: bz(re), jmallett, imp(mips)
2011-07-16 19:35:44 +00:00
#endif
#endif
Reference in New Issue Copy Permalink