d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
887ae9a1d2
freebsd-skq/sys/pci/if_sf.c

1531 lines
36 KiB
C
Raw Normal View History

This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/*
* Copyright (c) 1997, 1998, 1999
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
Remove duplicate FBSDID's, move others to their right place.
2003-11-14 17:16:58 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/*
* Adaptec AIC-6915 "Starfire" PCI fast ethernet driver for FreeBSD.
Update the Starfire driver comments and man page to include the URL of the AIC-6915 Programmer's Manual which I finally found online at Adaptec's site.
1999-09-26 18:35:30 +00:00
* Programming manual is available from:
* ftp.adaptec.com:/pub/BBS/userguides/aic6915_pg.pdf.
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
*
* Written by Bill Paul <wpaul@ctr.columbia.edu>
* Department of Electical Engineering
* Columbia University, New York City
*/
/*
* The Adaptec AIC-6915 "Starfire" is a 64-bit 10/100 PCI ethernet
* controller designed with flexibility and reducing CPU load in mind.
* The Starfire offers high and low priority buffer queues, a
* producer/consumer index mechanism and several different buffer
* queue and completion queue descriptor types. Any one of a number
* of different driver designs can be used, depending on system and
* OS requirements. This driver makes use of type0 transmit frame
* descriptors (since BSD fragments packets across an mbuf chain)
* and two RX buffer queues prioritized on size (one queue for small
* frames that will fit into a single mbuf, another with full size
* mbuf clusters for everything else). The producer/consumer indexes
* and completion queues are also used.
*
* One downside to the Starfire has to do with alignment: buffer
* queues must be aligned on 256-byte boundaries, and receive buffers
* must be aligned on longword boundaries. The receive buffer alignment
* causes problems on the Alpha platform, where the packet payload
* should be longword aligned. There is no simple way around this.
*
* For receive filtering, the Starfire offers 16 perfect filter slots
* and a 512-bit hash table.
*
* The Starfire has no internal transceiver, relying instead on an
* external MII-based transceiver. Accessing registers on external
* PHYs is done through a special register map rather than with the
* usual bitbang MDIO method.
*
* Acesssing the registers on the Starfire is a little tricky. The
* Starfire has a 512K internal register space. When programmed for
* PCI memory mapped mode, the entire register space can be accessed
* directly. However in I/O space mode, only 256 bytes are directly
* mapped into PCI I/O space. The other registers can be accessed
* indirectly using the SF_INDIRECTIO_ADDR and SF_INDIRECTIO_DATA
* registers inside the 256-byte I/O window.
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sockio.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <net/if.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/bpf.h>
#include <vm/vm.h> /* for vtophys */
#include <vm/pmap.h> /* for vtophys */
#include <machine/bus_pio.h>
#include <machine/bus_memio.h>
#include <machine/bus.h>
#include <machine/resource.h>
#include <sys/bus.h>
#include <sys/rman.h>
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
Add a pointer to "controller miibus0" for people who will not read the commit messages or GENERIC and insist on running -CURRENT. It probably won't work, but it's worth a try.
1999-09-08 15:01:58 +00:00
/* "controller miibus0" required. See GENERIC if you get errors here. */
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
#include "miibus_if.h"
Prefer new location of pci include files (which have only been in the tree for two or more years now), except in a few places where there's code to be compatible with older versions of FreeBSD.
2003-08-22 07:20:27 +00:00
#include <dev/pci/pcireg.h>
#include <dev/pci/pcivar.h>
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#define SF_USEIOSPACE
#include <pci/if_sfreg.h>
- Express hard dependencies on bus (pci, isa, pccard) and network layer (ether). - Don't abuse module names to facilitate ifconfig module loading; such abuse isn't really needed. (And if we do need type information associated with a module then we should make it explicit and not use hacks.)
2003-04-15 06:37:30 +00:00
MODULE_DEPEND(sf, pci, 1, 1, 1);
MODULE_DEPEND(sf, ether, 1, 1, 1);
Depend on miibus. Note that if_aue doesn't strictly depend on usb because it uses the method interface for calls rather than using internal symbols, and because it's a child driver of usb and therefore will not try and do anything unless the parent usb code is loaded at some point. if_aue does strictly depend on miibus as it will fail to link if it is missing.
2000-04-29 13:41:57 +00:00
MODULE_DEPEND(sf, miibus, 1, 1, 1);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
static struct sf_type sf_devs[] = {
{ AD_VENDORID, AD_DEVICEID_STARFIRE,
"Adaptec AIC-6915 10/100BaseTX" },
{ 0, 0, NULL }
};
Remove __P.
2002-03-20 02:08:01 +00:00
static int sf_probe (device_t);
static int sf_attach (device_t);
static int sf_detach (device_t);
static void sf_intr (void *);
static void sf_stats_update (void *);
static void sf_rxeof (struct sf_softc *);
static void sf_txeof (struct sf_softc *);
static int sf_encap (struct sf_softc *,
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_tx_bufdesc_type0 *,
Remove __P.
2002-03-20 02:08:01 +00:00
struct mbuf *);
static void sf_start (struct ifnet *);
static int sf_ioctl (struct ifnet *, u_long, caddr_t);
static void sf_init (void *);
static void sf_stop (struct sf_softc *);
static void sf_watchdog (struct ifnet *);
static void sf_shutdown (device_t);
static int sf_ifmedia_upd (struct ifnet *);
static void sf_ifmedia_sts (struct ifnet *, struct ifmediareq *);
static void sf_reset (struct sf_softc *);
static int sf_init_rx_ring (struct sf_softc *);
static void sf_init_tx_ring (struct sf_softc *);
static int sf_newbuf (struct sf_softc *,
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_rx_bufdesc_type0 *,
Remove __P.
2002-03-20 02:08:01 +00:00
struct mbuf *);
static void sf_setmulti (struct sf_softc *);
static int sf_setperf (struct sf_softc *, int, caddr_t);
static int sf_sethash (struct sf_softc *, caddr_t, int);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#ifdef notdef
Remove __P.
2002-03-20 02:08:01 +00:00
static int sf_setvlan (struct sf_softc *, int, u_int32_t);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#endif
Remove __P.
2002-03-20 02:08:01 +00:00
static u_int8_t sf_read_eeprom (struct sf_softc *, int);
Don't use caddr_t in mchash(). Also use C99 spellings over BSD ones. Requested by: bde,imp
2003-12-08 07:54:15 +00:00
static uint32_t sf_mchash (const uint8_t *);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
Remove __P.
2002-03-20 02:08:01 +00:00
static int sf_miibus_readreg (device_t, int, int);
static int sf_miibus_writereg (device_t, int, int, int);
static void sf_miibus_statchg (device_t);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
Remove __P.
2002-03-20 02:08:01 +00:00
static u_int32_t csr_read_4 (struct sf_softc *, int);
static void csr_write_4 (struct sf_softc *, int, u_int32_t);
static void sf_txthresh_adjust (struct sf_softc *);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#ifdef SF_USEIOSPACE
#define SF_RES SYS_RES_IOPORT
#define SF_RID SF_PCI_LOIO
#else
#define SF_RES SYS_RES_MEMORY
#define SF_RID SF_PCI_LOMEM
#endif
static device_method_t sf_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, sf_probe),
DEVMETHOD(device_attach, sf_attach),
DEVMETHOD(device_detach, sf_detach),
DEVMETHOD(device_shutdown, sf_shutdown),
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
/* bus interface */
DEVMETHOD(bus_print_child, bus_generic_print_child),
DEVMETHOD(bus_driver_added, bus_generic_driver_added),
/* MII interface */
DEVMETHOD(miibus_readreg, sf_miibus_readreg),
DEVMETHOD(miibus_writereg, sf_miibus_writereg),
DEVMETHOD(miibus_statchg, sf_miibus_statchg),
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
{ 0, 0 }
};
static driver_t sf_driver = {
Grrr. Okay, changing the devnames was a bad idea. Put them back the way they were.
1999-09-20 08:47:11 +00:00
"sf",
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sf_methods,
sizeof(struct sf_softc),
};
static devclass_t sf_devclass;
- Express hard dependencies on bus (pci, isa, pccard) and network layer (ether). - Don't abuse module names to facilitate ifconfig module loading; such abuse isn't really needed. (And if we do need type information associated with a module then we should make it explicit and not use hacks.)
2003-04-15 06:37:30 +00:00
DRIVER_MODULE(sf, pci, sf_driver, sf_devclass, 0, 0);
Un-do the changes to the DRIVER_MODULE() declarations in these drivers. This whole idea isn't going to work until somebody makes the bus/kld code smarter. The idea here is to change the module's internal name from "foo" to "if_foo" so that ifconfig can tell a network driver from a non-network one. However doing this doesn't work correctly no matter how you slice it. For everything to work, you have to change the name in both the driver_t struct and the DRIVER_MODULE() declaration. The problems are: - If you change the name in both places, then the kernel thinks that the device's name is now "if_foo", so you get things like: if_foo0: <FOO ethernet> irq foo at device foo on pcifoo if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo This is bogus. Now the device name doesn't agree with the logical interface name. There's no reason for this, and it violates the principle of least astonishment. - If you leave the name in the driver_t struct as "foo" and only change the names in the DRIVER_MODULE() declaration to "if_foo" then attaching drivers to child devices doesn't work because the names don't agree. This breaks miibus: drivers that need to have miibuses and PHY drivers attached never get them. In other words: damned if you do, damned if you don't. This needs to be thought through some more. Since the drivers that use miibus are broken, I have to change these all back in order to make them work again. Yes this will stop ifconfig from being able to demand load driver modules. On the whole, I'd rather have that than having the drivers not work at all.
1999-09-20 19:06:45 +00:00
DRIVER_MODULE(miibus, sf, miibus_driver, miibus_devclass, 0, 0);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#define SF_SETBIT(sc, reg, x) \
Be consistent about functions being static. Properly put macro args in (). Spotted by: FlexeLint.
2002-10-16 09:14:59 +00:00
csr_write_4(sc, reg, csr_read_4(sc, reg) | (x))
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
#define SF_CLRBIT(sc, reg, x) \
Be consistent about functions being static. Properly put macro args in (). Spotted by: FlexeLint.
2002-10-16 09:14:59 +00:00
csr_write_4(sc, reg, csr_read_4(sc, reg) & ~(x))
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static u_int32_t
csr_read_4(sc, reg)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
int reg;
{
u_int32_t val;
#ifdef SF_USEIOSPACE
CSR_WRITE_4(sc, SF_INDIRECTIO_ADDR, reg + SF_RMAP_INTREG_BASE);
val = CSR_READ_4(sc, SF_INDIRECTIO_DATA);
#else
val = CSR_READ_4(sc, (reg + SF_RMAP_INTREG_BASE));
#endif
return(val);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static u_int8_t
sf_read_eeprom(sc, reg)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
int reg;
{
u_int8_t val;
val = (csr_read_4(sc, SF_EEADDR_BASE +
(reg & 0xFFFFFFFC)) >> (8 * (reg & 3))) & 0xFF;
return(val);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
csr_write_4(sc, reg, val)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
int reg;
u_int32_t val;
{
#ifdef SF_USEIOSPACE
CSR_WRITE_4(sc, SF_INDIRECTIO_ADDR, reg + SF_RMAP_INTREG_BASE);
CSR_WRITE_4(sc, SF_INDIRECTIO_DATA, val);
#else
CSR_WRITE_4(sc, (reg + SF_RMAP_INTREG_BASE), val);
#endif
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static u_int32_t
Try to create some sort of consistency in how the routings to find the multicast hash are written. There are still two distinct algorithms used, and there actually isn't any reason each driver should have its own copy of this function as they could all share one copy of it (if it grew an additional argument).
2003-11-13 20:55:53 +00:00
sf_mchash(addr)
Don't use caddr_t in mchash(). Also use C99 spellings over BSD ones. Requested by: bde,imp
2003-12-08 07:54:15 +00:00
const uint8_t *addr;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
{
Don't use caddr_t in mchash(). Also use C99 spellings over BSD ones. Requested by: bde,imp
2003-12-08 07:54:15 +00:00
uint32_t crc, carry;
int idx, bit;
uint8_t data;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/* Compute CRC for the address value. */
crc = 0xFFFFFFFF; /* initial value */
Try to create some sort of consistency in how the routings to find the multicast hash are written. There are still two distinct algorithms used, and there actually isn't any reason each driver should have its own copy of this function as they could all share one copy of it (if it grew an additional argument).
2003-11-13 20:55:53 +00:00
for (idx = 0; idx < 6; idx++) {
for (data = *addr++, bit = 0; bit < 8; bit++, data >>= 1) {
carry = ((crc & 0x80000000) ? 1 : 0) ^ (data & 0x01);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
crc <<= 1;
if (carry)
crc = (crc ^ 0x04c11db6) | carry;
}
}
/* return the filter bit position */
return(crc >> 23 & 0x1FF);
}
/*
* Copy the address 'mac' into the perfect RX filter entry at
* offset 'idx.' The perfect filter only has 16 entries so do
* some sanity tests.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_setperf(sc, idx, mac)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
int idx;
caddr_t mac;
{
u_int16_t *p;
if (idx < 0 || idx > SF_RXFILT_PERFECT_CNT)
return(EINVAL);
if (mac == NULL)
return(EINVAL);
p = (u_int16_t *)mac;
csr_write_4(sc, SF_RXFILT_PERFECT_BASE +
(idx * SF_RXFILT_PERFECT_SKIP), htons(p[2]));
csr_write_4(sc, SF_RXFILT_PERFECT_BASE +
(idx * SF_RXFILT_PERFECT_SKIP) + 4, htons(p[1]));
csr_write_4(sc, SF_RXFILT_PERFECT_BASE +
(idx * SF_RXFILT_PERFECT_SKIP) + 8, htons(p[0]));
return(0);
}
/*
* Set the bit in the 512-bit hash table that corresponds to the
* specified mac address 'mac.' If 'prio' is nonzero, update the
* priority hash table instead of the filter hash table.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_sethash(sc, mac, prio)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
caddr_t mac;
int prio;
{
u_int32_t h = 0;
if (mac == NULL)
return(EINVAL);
Try to create some sort of consistency in how the routings to find the multicast hash are written. There are still two distinct algorithms used, and there actually isn't any reason each driver should have its own copy of this function as they could all share one copy of it (if it grew an additional argument).
2003-11-13 20:55:53 +00:00
h = sf_mchash(mac);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (prio) {
SF_SETBIT(sc, SF_RXFILT_HASH_BASE + SF_RXFILT_HASH_PRIOOFF +
(SF_RXFILT_HASH_SKIP * (h >> 4)), (1 << (h & 0xF)));
} else {
SF_SETBIT(sc, SF_RXFILT_HASH_BASE + SF_RXFILT_HASH_ADDROFF +
(SF_RXFILT_HASH_SKIP * (h >> 4)), (1 << (h & 0xF)));
}
return(0);
}
#ifdef notdef
/*
* Set a VLAN tag in the receive filter.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_setvlan(sc, idx, vlan)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
int idx;
u_int32_t vlan;
{
if (idx < 0 || idx >> SF_RXFILT_HASH_CNT)
return(EINVAL);
csr_write_4(sc, SF_RXFILT_HASH_BASE +
(idx * SF_RXFILT_HASH_SKIP) + SF_RXFILT_HASH_VLANOFF, vlan);
return(0);
}
#endif
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_miibus_readreg(dev, phy, reg)
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
device_t dev;
int phy, reg;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
{
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct sf_softc *sc;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
int i;
u_int32_t val = 0;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
sc = device_get_softc(dev);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
for (i = 0; i < SF_TIMEOUT; i++) {
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
val = csr_read_4(sc, SF_PHY_REG(phy, reg));
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (val & SF_MII_DATAVALID)
break;
}
if (i == SF_TIMEOUT)
return(0);
if ((val & 0x0000FFFF) == 0xFFFF)
return(0);
return(val & 0x0000FFFF);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_miibus_writereg(dev, phy, reg, val)
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
device_t dev;
int phy, reg, val;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
{
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct sf_softc *sc;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
int i;
int busy;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
sc = device_get_softc(dev);
csr_write_4(sc, SF_PHY_REG(phy, reg), val);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
for (i = 0; i < SF_TIMEOUT; i++) {
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
busy = csr_read_4(sc, SF_PHY_REG(phy, reg));
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (!(busy & SF_MII_BUSY))
break;
}
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
return(0);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_miibus_statchg(dev)
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
device_t dev;
{
struct sf_softc *sc;
struct mii_data *mii;
sc = device_get_softc(dev);
mii = device_get_softc(sc->sf_miibus);
if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) {
SF_SETBIT(sc, SF_MACCFG_1, SF_MACCFG1_FULLDUPLEX);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
csr_write_4(sc, SF_BKTOBKIPG, SF_IPGT_FDX);
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
} else {
SF_CLRBIT(sc, SF_MACCFG_1, SF_MACCFG1_FULLDUPLEX);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
csr_write_4(sc, SF_BKTOBKIPG, SF_IPGT_HDX);
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_setmulti(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
struct ifnet *ifp;
int i;
struct ifmultiaddr *ifma;
u_int8_t dummy[] = { 0, 0, 0, 0, 0, 0 };
ifp = &sc->arpcom.ac_if;
/* First zot all the existing filters. */
for (i = 1; i < SF_RXFILT_PERFECT_CNT; i++)
sf_setperf(sc, i, (char *)&dummy);
for (i = SF_RXFILT_HASH_BASE;
i < (SF_RXFILT_HASH_MAX + 1); i += 4)
csr_write_4(sc, i, 0);
SF_CLRBIT(sc, SF_RXFILT, SF_RXFILT_ALLMULTI);
/* Now program new ones. */
if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) {
SF_SETBIT(sc, SF_RXFILT, SF_RXFILT_ALLMULTI);
} else {
i = 1;
Convert if_multiaddrs from LIST to TAILQ so that it can be traversed backwards in the three drivers which want to do that. Reviewed by: mikeh
2001-02-06 10:12:15 +00:00
TAILQ_FOREACH_REVERSE(ifma, &ifp->if_multiaddrs, ifmultihead, ifma_link) {
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
/*
* Program the first 15 multicast groups
* into the perfect filter. For all others,
* use the hash table.
*/
if (i < SF_RXFILT_PERFECT_CNT) {
sf_setperf(sc, i,
LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
i++;
continue;
}
sf_sethash(sc,
LLADDR((struct sockaddr_dl *)ifma->ifma_addr), 0);
}
}
return;
}
/*
* Set media options.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_ifmedia_upd(ifp)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct ifnet *ifp;
{
struct sf_softc *sc;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct mii_data *mii;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc = ifp->if_softc;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii = device_get_softc(sc->sf_miibus);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
sc->sf_link = 0;
if (mii->mii_instance) {
struct mii_softc *miisc;
Another round of the <sys/queue.h> FOREACH transmogriffer. Created with: sed(1) Reviewed by: md5(1)
2001-02-04 16:08:18 +00:00
LIST_FOREACH(miisc, &mii->mii_phys, mii_list)
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
mii_phy_reset(miisc);
}
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii_mediachg(mii);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(0);
}
/*
* Report current media status.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_ifmedia_sts(ifp, ifmr)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct ifnet *ifp;
struct ifmediareq *ifmr;
{
struct sf_softc *sc;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct mii_data *mii;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc = ifp->if_softc;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii = device_get_softc(sc->sf_miibus);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii_pollstat(mii);
ifmr->ifm_active = mii->mii_media_active;
ifmr->ifm_status = mii->mii_media_status;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_ioctl(ifp, command, data)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct ifnet *ifp;
u_long command;
caddr_t data;
{
struct sf_softc *sc = ifp->if_softc;
struct ifreq *ifr = (struct ifreq *) data;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct mii_data *mii;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
int error = 0;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
switch(command) {
case SIOCSIFFLAGS:
if (ifp->if_flags & IFF_UP) {
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
if (ifp->if_flags & IFF_RUNNING &&
ifp->if_flags & IFF_PROMISC &&
!(sc->sf_if_flags & IFF_PROMISC)) {
SF_SETBIT(sc, SF_RXFILT, SF_RXFILT_PROMISC);
} else if (ifp->if_flags & IFF_RUNNING &&
!(ifp->if_flags & IFF_PROMISC) &&
sc->sf_if_flags & IFF_PROMISC) {
SF_CLRBIT(sc, SF_RXFILT, SF_RXFILT_PROMISC);
} else if (!(ifp->if_flags & IFF_RUNNING))
sf_init(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
} else {
if (ifp->if_flags & IFF_RUNNING)
sf_stop(sc);
}
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
sc->sf_if_flags = ifp->if_flags;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
error = 0;
break;
case SIOCADDMULTI:
case SIOCDELMULTI:
sf_setmulti(sc);
error = 0;
break;
case SIOCGIFMEDIA:
case SIOCSIFMEDIA:
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii = device_get_softc(sc->sf_miibus);
error = ifmedia_ioctl(ifp, ifr, &mii->mii_media, command);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
break;
default:
o track either_ifattach/ether_ifdetach API changes o use if_input for input packet processing o don't strip the Ethernet header for input packets o use BPF_* macros bpf tapping o call ether_ioctl to handle default ioctl case o track vlan changes Reviewed by: many Approved by: re
2002-11-14 23:49:09 +00:00
error = ether_ioctl(ifp, command, data);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
break;
}
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(error);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_reset(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
register int i;
csr_write_4(sc, SF_GEN_ETH_CTL, 0);
SF_SETBIT(sc, SF_MACCFG_1, SF_MACCFG1_SOFTRESET);
DELAY(1000);
SF_CLRBIT(sc, SF_MACCFG_1, SF_MACCFG1_SOFTRESET);
SF_SETBIT(sc, SF_PCI_DEVCFG, SF_PCIDEVCFG_RESET);
for (i = 0; i < SF_TIMEOUT; i++) {
DELAY(10);
if (!(csr_read_4(sc, SF_PCI_DEVCFG) & SF_PCIDEVCFG_RESET))
break;
}
if (i == SF_TIMEOUT)
printf("sf%d: reset never completed!\n", sc->sf_unit);
/* Wait a little while for the chip to get its brains in order. */
DELAY(1000);
return;
}
/*
* Probe for an Adaptec AIC-6915 chip. Check the PCI vendor and device
* IDs against our list and return a device name if we find a match.
* We also check the subsystem ID so that we can identify exactly which
* NIC has been found, if possible.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_probe(dev)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
device_t dev;
{
struct sf_type *t;
t = sf_devs;
while(t->sf_name != NULL) {
if ((pci_get_vendor(dev) == t->sf_vid) &&
(pci_get_device(dev) == t->sf_did)) {
Fix sf_probe() to detect the card type properly. I botched the reading of the subsystem ID when I converted to newbus. The driver still detects the chipset and still works but fails to identify the exact card.
1999-09-17 00:47:41 +00:00
switch((pci_read_config(dev,
SF_PCI_SUBVEN_ID, 4) >> 16) & 0xFFFF) {
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
case AD_SUBSYSID_62011_REV0:
case AD_SUBSYSID_62011_REV1:
device_set_desc(dev,
"Adaptec ANA-62011 10/100BaseTX");
return(0);
case AD_SUBSYSID_62022:
device_set_desc(dev,
"Adaptec ANA-62022 10/100BaseTX");
return(0);
Minor tweak: the subsystem device ID code for the quad port 62044 card is documented to be 0x18 in the Adaptec manual, however there appears to be a newer board rev with code 0x19. I added a #define for this and updated the probe code so that this board will be properly identified in the probe messages. (Currently it's just identified generically as an AIC-6915 chip.)
1999-11-20 18:29:44 +00:00
case AD_SUBSYSID_62044_REV0:
case AD_SUBSYSID_62044_REV1:
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
device_set_desc(dev,
"Adaptec ANA-62044 10/100BaseTX");
return(0);
case AD_SUBSYSID_62020:
device_set_desc(dev,
"Adaptec ANA-62020 10/100BaseFX");
return(0);
case AD_SUBSYSID_69011:
device_set_desc(dev,
"Adaptec ANA-69011 10/100BaseTX");
return(0);
default:
device_set_desc(dev, t->sf_name);
return(0);
break;
}
}
t++;
}
return(ENXIO);
}
/*
* Attach the interface. Allocate softc structures, do ifmedia
* setup and ethernet/BPF attach.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_attach(dev)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
device_t dev;
{
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
int i;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
struct ifnet *ifp;
int unit, rid, error = 0;
sc = device_get_softc(dev);
unit = device_get_unit(dev);
Change callers of mtx_init() to pass in an appropriate lock type name. In most cases NULL is passed, but in some cases such as network driver locks (which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used. Tested on: i386, alpha, sparc64
2002-04-04 21:03:38 +00:00
mtx_init(&sc->sf_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK,
MTX_DEF | MTX_RECURSE);
Due to extreme bogusness in the pci bus layer, these drivers were forced to do slightly bogus power state manipulation. However, this is one of those features that is preventing further progress, so mark them as BURN_BIRDGES like I did for the drivers in sys/dev/... This, like the other change, are a no-op unless you have BURN_BRIDGES in your kernel.
2003-07-03 21:39:53 +00:00
#ifndef BURN_BRIDGES
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/*
* Handle power management nonsense.
*/
Big round of minor updates: - Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers that need them so we don't have to fiddle with the PCI power management registers directly. - Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and PIO/memory mapped accesses. - Add support to the RealTek driver for the D-Link DFE-530TX+ which has a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright) - Have the SiS 900/National DP83815 driver be sure to disable PME mode in sis_reset(). This apparently fixes a problem on some motherboards where the DP83815 chip fails to receive packets. (Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
2001-02-21 20:54:22 +00:00
if (pci_get_powerstate(dev) != PCI_POWERSTATE_D0) {
u_int32_t iobase, membase, irq;
/* Save important PCI config data. */
iobase = pci_read_config(dev, SF_PCI_LOIO, 4);
membase = pci_read_config(dev, SF_PCI_LOMEM, 4);
irq = pci_read_config(dev, SF_PCI_INTLINE, 4);
/* Reset the power state. */
printf("sf%d: chip is in D%d power mode "
"-- setting to D0\n", unit,
pci_get_powerstate(dev));
pci_set_powerstate(dev, PCI_POWERSTATE_D0);
/* Restore PCI config data. */
pci_write_config(dev, SF_PCI_LOIO, iobase, 4);
pci_write_config(dev, SF_PCI_LOMEM, membase, 4);
pci_write_config(dev, SF_PCI_INTLINE, irq, 4);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
}
Due to extreme bogusness in the pci bus layer, these drivers were forced to do slightly bogus power state manipulation. However, this is one of those features that is preventing further progress, so mark them as BURN_BIRDGES like I did for the drivers in sys/dev/... This, like the other change, are a no-op unless you have BURN_BRIDGES in your kernel.
2003-07-03 21:39:53 +00:00
#endif
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/*
* Map control/status registers.
*/
Big round of minor updates: - Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers that need them so we don't have to fiddle with the PCI power management registers directly. - Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and PIO/memory mapped accesses. - Add support to the RealTek driver for the D-Link DFE-530TX+ which has a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright) - Have the SiS 900/National DP83815 driver be sure to disable PME mode in sis_reset(). This apparently fixes a problem on some motherboards where the DP83815 chip fails to receive packets. (Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
2001-02-21 20:54:22 +00:00
pci_enable_busmaster(dev);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
rid = SF_RID;
Convert callers to the new bus_alloc_resource_any(9) API. Submitted by: Mark Santcroos <marks@ripe.net> Reviewed by: imp, dfr, bde
2004-03-17 17:50:55 +00:00
sc->sf_res = bus_alloc_resource_any(dev, SF_RES, &rid, RF_ACTIVE);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (sc->sf_res == NULL) {
printf ("sf%d: couldn't map ports\n", unit);
error = ENXIO;
goto fail;
}
sc->sf_btag = rman_get_bustag(sc->sf_res);
sc->sf_bhandle = rman_get_bushandle(sc->sf_res);
/* Allocate interrupt */
rid = 0;
Convert callers to the new bus_alloc_resource_any(9) API. Submitted by: Mark Santcroos <marks@ripe.net> Reviewed by: imp, dfr, bde
2004-03-17 17:50:55 +00:00
sc->sf_irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid,
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
RF_SHAREABLE | RF_ACTIVE);
if (sc->sf_irq == NULL) {
printf("sf%d: couldn't map interrupt\n", unit);
error = ENXIO;
goto fail;
}
callout_handle_init(&sc->sf_stat_ch);
/* Reset the adapter. */
sf_reset(sc);
/*
* Get station address from the EEPROM.
*/
for (i = 0; i < ETHER_ADDR_LEN; i++)
sc->arpcom.ac_enaddr[i] =
sf_read_eeprom(sc, SF_EE_NODEADDR + ETHER_ADDR_LEN - i);
sc->sf_unit = unit;
/* Allocate the descriptor queues. */
sc->sf_ldata = contigmalloc(sizeof(struct sf_list_data), M_DEVBUF,
Change contigmalloc() lower memory bound from 1MB to 0 to improve chances of allocations succeeding on systems with small amounts of RAM. Pointed out by: bde
1999-09-25 17:29:02 +00:00
M_NOWAIT, 0, 0xffffffff, PAGE_SIZE, 0);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (sc->sf_ldata == NULL) {
printf("sf%d: no memory for list buffers!\n", unit);
error = ENXIO;
goto fail;
}
bzero(sc->sf_ldata, sizeof(struct sf_list_data));
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
/* Do MII setup. */
if (mii_phy_probe(dev, &sc->sf_miibus,
sf_ifmedia_upd, sf_ifmedia_sts)) {
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
printf("sf%d: MII without any phy!\n", sc->sf_unit);
error = ENXIO;
goto fail;
}
ifp = &sc->arpcom.ac_if;
ifp->if_softc = sc;
Replace the if_name and if_unit members of struct ifnet with new members if_xname, if_dname, and if_dunit. if_xname is the name of the interface and if_dname/unit are the driver name and instance. This change paves the way for interface renaming and enhanced pseudo device creation and configuration symantics. Approved By: re (in principle) Reviewed By: njl, imp Tested On: i386, amd64, sparc64 Obtained From: NetBSD (if_xname)
2003-10-31 18:32:15 +00:00
if_initname(ifp, device_get_name(dev), device_get_unit(dev));
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp->if_mtu = ETHERMTU;
ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
ifp->if_ioctl = sf_ioctl;
ifp->if_start = sf_start;
ifp->if_watchdog = sf_watchdog;
ifp->if_init = sf_init;
ifp->if_baudrate = 10000000;
ifp->if_snd.ifq_maxlen = SF_TX_DLIST_CNT - 1;
/*
Make all Ethernet drivers attach using ether_ifattach() and detach using ether_ifdetach(). The former consolidates the operations of if_attach(), ng_ether_attach(), and bpfattach(). The latter consolidates the corresponding detach operations. Reviewed by: julian, freebsd-net
2000-07-13 22:54:34 +00:00
* Call MI attach routine.
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
*/
o track either_ifattach/ether_ifdetach API changes o use if_input for input packet processing o don't strip the Ethernet header for input packets o use BPF_* macros bpf tapping o call ether_ioctl to handle default ioctl case o track vlan changes Reviewed by: many Approved by: re
2002-11-14 23:49:09 +00:00
ether_ifattach(ifp, sc->arpcom.ac_enaddr);
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
/* Hook interrupt last to avoid having to lock softc */
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
error = bus_setup_intr(dev, sc->sf_irq, INTR_TYPE_NET,
sf_intr, sc, &sc->sf_intrhand);
if (error) {
printf("sf%d: couldn't set up irq\n", unit);
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
ether_ifdetach(ifp);
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
goto fail;
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
fail:
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
if (error)
sf_detach(dev);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(error);
}
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
/*
* Shutdown hardware and free up resources. This can be called any
* time after the mutex has been initialized. It is called in both
* the error case in attach and the normal detach case so it needs
* to be careful about only freeing resources that have actually been
* allocated.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_detach(dev)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
device_t dev;
{
struct sf_softc *sc;
struct ifnet *ifp;
sc = device_get_softc(dev);
Add missing ()'s so that these drivers all compile again. Noticed by: jake Tested on: i386 (compile)
2003-03-31 20:22:00 +00:00
KASSERT(mtx_initialized(&sc->sf_mtx), ("sf mutex not initialized"));
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp = &sc->arpcom.ac_if;
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
/* These should only be active if attach succeeded */
Use newly minted device_is_attached rather than device_is_alive to see if attach succeeded. device_is_alive just tells us that probe succeeded. Since we were using it to do things like detach net interfaces, this caused problems when there were errors in the attach routine. Symptoms of problem reported by: martin blapp
2003-04-21 18:34:04 +00:00
if (device_is_attached(dev)) {
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
sf_stop(sc);
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
ether_ifdetach(ifp);
}
Revise attach/detach resource cleanup - Unconditionally call *_stop() if device is in the tree. This is to prevent callouts from happening after the device is gone. Checks for bus_child_present() should be added in the future to keep from touching potentially non-existent hardware in *_detach(). Found by iedowse@. - Always check for and free miibus children, even if the device is not in the tree since some failure cases could have gotten here. - Call ether_ifdetach() in the irq setup failure case - ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so that ifmedia_removeall() can be unconditionally called on detach. There is no way to detect whether ifmedia has been initialized without using a separate variable (as tl(4) does). - Add comments to indicate assumptions of code path
2003-04-17 20:32:06 +00:00
if (sc->sf_miibus)
device_delete_child(dev, sc->sf_miibus);
bus_generic_detach(dev);
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
if (sc->sf_intrhand)
bus_teardown_intr(dev, sc->sf_irq, sc->sf_intrhand);
if (sc->sf_irq)
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->sf_irq);
if (sc->sf_res)
bus_release_resource(dev, SF_RES, SF_RID, sc->sf_res);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
Clean up locking and resource management for pci/if_* - Remove locking of the softc in the attach method, instead depending on bus_setup_intr being at the end of attach (delaying interrupt enable until after ether_ifattach is called) - Call *_detach directly in the error case of attach, depending on checking in detach to only free resources that were allocated. This puts all resource freeing in one place, avoiding thinkos that lead to memory leaks. - Add bus_child_present check to calls to *_stop in the detach method to be sure hw is present before touching its registers. - Remove bzero softc calls since device_t should do this for us. - dc: move interrupt allocation back where it was before. It was unnecessary to move it. This reverts part of 1.88 - rl: move irq allocation before ether_ifattach. Problems might have been caused by allocating the irq after enabling interrupts on the card. - rl: call rl_stop before ether_ifdetach - sf: call sf_stop before ether_ifdetach - sis: add missed free of sis_tag - sis: check errors from tag creation - sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation - sk: remove duplicate initialization of sk_dev - ste: add missed bus_generic_detach - ti: call ti_stop before ether_ifdetach - ti: add missed error setting in ti_rdata alloc failure - vr: add missed error setting in I/O, memory mapping cases - xl: add missed error setting in I/O, memory mapping cases - xl: remove multi-level goto on attach failure - xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation - Calls to free(9) are unconditional because it is valid to call free with a null pointer. Reviewed by: imp, mdodd
2003-03-31 17:29:43 +00:00
if (sc->sf_ldata)
contigfree(sc->sf_ldata, sizeof(struct sf_list_data), M_DEVBUF);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
mtx_destroy(&sc->sf_mtx);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(0);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_init_rx_ring(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
struct sf_list_data *ld;
int i;
ld = sc->sf_ldata;
bzero((char *)ld->sf_rx_dlist_big,
sizeof(struct sf_rx_bufdesc_type0) * SF_RX_DLIST_CNT);
bzero((char *)ld->sf_rx_clist,
sizeof(struct sf_rx_cmpdesc_type3) * SF_RX_CLIST_CNT);
for (i = 0; i < SF_RX_DLIST_CNT; i++) {
if (sf_newbuf(sc, &ld->sf_rx_dlist_big[i], NULL) == ENOBUFS)
return(ENOBUFS);
}
return(0);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_init_tx_ring(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
struct sf_list_data *ld;
int i;
ld = sc->sf_ldata;
bzero((char *)ld->sf_tx_dlist,
sizeof(struct sf_tx_bufdesc_type0) * SF_TX_DLIST_CNT);
bzero((char *)ld->sf_tx_clist,
sizeof(struct sf_tx_cmpdesc_type0) * SF_TX_CLIST_CNT);
for (i = 0; i < SF_TX_DLIST_CNT; i++)
ld->sf_tx_dlist[i].sf_id = SF_TX_BUFDESC_ID;
for (i = 0; i < SF_TX_CLIST_CNT; i++)
ld->sf_tx_clist[i].sf_type = SF_TXCMPTYPE_TX;
ld->sf_tx_dlist[SF_TX_DLIST_CNT - 1].sf_end = 1;
sc->sf_tx_cnt = 0;
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_newbuf(sc, c, m)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
struct sf_rx_bufdesc_type0 *c;
struct mbuf *m;
{
struct mbuf *m_new = NULL;
if (m == NULL) {
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
Remove printf's on mbuf/cluster allocation failures. There are now equivalent and less dangerous (rate limited) messages in the mbuf allocation code. MFC after: 3 days
2001-12-14 05:56:35 +00:00
if (m_new == NULL)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(ENOBUFS);
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MCLGET(m_new, M_DONTWAIT);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (!(m_new->m_flags & M_EXT)) {
m_freem(m_new);
return(ENOBUFS);
}
m_new->m_len = m_new->m_pkthdr.len = MCLBYTES;
} else {
m_new = m;
m_new->m_len = m_new->m_pkthdr.len = MCLBYTES;
m_new->m_data = m_new->m_ext.ext_buf;
}
m_adj(m_new, sizeof(u_int64_t));
c->sf_mbuf = m_new;
c->sf_addrlo = SF_RX_HOSTADDR(vtophys(mtod(m_new, caddr_t)));
c->sf_valid = 1;
return(0);
}
/*
* The starfire is programmed to use 'normal' mode for packet reception,
* which means we use the consumer/producer model for both the buffer
* descriptor queue and the completion descriptor queue. The only problem
* with this is that it involves a lot of register accesses: we have to
* read the RX completion consumer and producer indexes and the RX buffer
* producer index, plus the RX completion consumer and RX buffer producer
* indexes have to be updated. It would have been easier if Adaptec had
* put each index in a separate register, especially given that the damn
* NIC has a 512K register space.
*
* In spite of all the lovely features that Adaptec crammed into the 6915,
* it is marred by one truly stupid design flaw, which is that receive
* buffer addresses must be aligned on a longword boundary. This forces
* the packet payload to be unaligned, which is suboptimal on the x86 and
* completely unuseable on the Alpha. Our only recourse is to copy received
* packets into properly aligned buffers before handing them off.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_rxeof(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
struct mbuf *m;
struct ifnet *ifp;
struct sf_rx_bufdesc_type0 *desc;
struct sf_rx_cmpdesc_type3 *cur_rx;
u_int32_t rxcons, rxprod;
int cmpprodidx, cmpconsidx, bufprodidx;
Drop the driver lock around calls to if_input to avoid a LOR when the packets are immediately returned for sending (e.g. when bridging or packet forwarding). There are more efficient ways to do this but for now use the least intrusive approach. Reviewed by: imp, rwatson
2003-11-14 19:00:32 +00:00
SF_LOCK_ASSERT(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp = &sc->arpcom.ac_if;
rxcons = csr_read_4(sc, SF_CQ_CONSIDX);
rxprod = csr_read_4(sc, SF_RXDQ_PTR_Q1);
cmpprodidx = SF_IDX_LO(csr_read_4(sc, SF_CQ_PRODIDX));
cmpconsidx = SF_IDX_LO(rxcons);
bufprodidx = SF_IDX_LO(rxprod);
while (cmpconsidx != cmpprodidx) {
struct mbuf *m0;
cur_rx = &sc->sf_ldata->sf_rx_clist[cmpconsidx];
desc = &sc->sf_ldata->sf_rx_dlist_big[cur_rx->sf_endidx];
m = desc->sf_mbuf;
SF_INC(cmpconsidx, SF_RX_CLIST_CNT);
SF_INC(bufprodidx, SF_RX_DLIST_CNT);
if (!(cur_rx->sf_status1 & SF_RXSTAT1_OK)) {
ifp->if_ierrors++;
sf_newbuf(sc, desc, m);
continue;
}
Change m_devget()'s outdated and unused `offset' argument to actually mean something: offset into the first mbuf of the target chain before copying the source data over. Make drivers using m_devget() with a first argument "data - ETHER_ALIGN" to use the offset argument to pass ETHER_ALIGN in. The way it was previously done is potentially dangerous if the source data was at the top of a page and the offset caused the previous page to be copied (if the previous page has not yet been appropriately mapped). The old `offset' argument in m_devget() is not used anywhere (it's always 0) and dates back to ~1995 (and earlier?) when support for ethernet trailers existed. With that support gone, it was merely collecting dust. Tested on alpha by: jlemon Partially submitted by: jlemon Reviewed by: jlemon MFC after: 3 weeks
2001-06-20 19:48:35 +00:00
m0 = m_devget(mtod(m, char *), cur_rx->sf_len, ETHER_ALIGN,
ifp, NULL);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sf_newbuf(sc, desc, m);
if (m0 == NULL) {
ifp->if_ierrors++;
continue;
}
m = m0;
ifp->if_ipackets++;
Drop the driver lock around calls to if_input to avoid a LOR when the packets are immediately returned for sending (e.g. when bridging or packet forwarding). There are more efficient ways to do this but for now use the least intrusive approach. Reviewed by: imp, rwatson
2003-11-14 19:00:32 +00:00
SF_UNLOCK(sc);
o track either_ifattach/ether_ifdetach API changes o use if_input for input packet processing o don't strip the Ethernet header for input packets o use BPF_* macros bpf tapping o call ether_ioctl to handle default ioctl case o track vlan changes Reviewed by: many Approved by: re
2002-11-14 23:49:09 +00:00
(*ifp->if_input)(ifp, m);
Drop the driver lock around calls to if_input to avoid a LOR when the packets are immediately returned for sending (e.g. when bridging or packet forwarding). There are more efficient ways to do this but for now use the least intrusive approach. Reviewed by: imp, rwatson
2003-11-14 19:00:32 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
}
csr_write_4(sc, SF_CQ_CONSIDX,
(rxcons & ~SF_CQ_CONSIDX_RXQ1) | cmpconsidx);
csr_write_4(sc, SF_RXDQ_PTR_Q1,
(rxprod & ~SF_RXDQ_PRODIDX) | bufprodidx);
return;
}
/*
* Read the transmit status from the completion queue and release
* mbufs. Note that the buffer descriptor index in the completion
* descriptor is an offset from the start of the transmit buffer
* descriptor list in bytes. This is important because the manual
* gives the impression that it should match the producer/consumer
* index, which is the offset in 8 byte blocks.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_txeof(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
int txcons, cmpprodidx, cmpconsidx;
struct sf_tx_cmpdesc_type1 *cur_cmp;
struct sf_tx_bufdesc_type0 *cur_tx;
struct ifnet *ifp;
ifp = &sc->arpcom.ac_if;
txcons = csr_read_4(sc, SF_CQ_CONSIDX);
cmpprodidx = SF_IDX_HI(csr_read_4(sc, SF_CQ_PRODIDX));
cmpconsidx = SF_IDX_HI(txcons);
while (cmpconsidx != cmpprodidx) {
cur_cmp = &sc->sf_ldata->sf_tx_clist[cmpconsidx];
cur_tx = &sc->sf_ldata->sf_tx_dlist[cur_cmp->sf_index >> 7];
if (cur_cmp->sf_txstat & SF_TXSTAT_TX_OK)
ifp->if_opackets++;
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
else {
if (cur_cmp->sf_txstat & SF_TXSTAT_TX_UNDERRUN)
sf_txthresh_adjust(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp->if_oerrors++;
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc->sf_tx_cnt--;
if (cur_tx->sf_mbuf != NULL) {
m_freem(cur_tx->sf_mbuf);
cur_tx->sf_mbuf = NULL;
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
} else
break;
SF_INC(cmpconsidx, SF_TX_CLIST_CNT);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
}
ifp->if_timer = 0;
ifp->if_flags &= ~IFF_OACTIVE;
csr_write_4(sc, SF_CQ_CONSIDX,
(txcons & ~SF_CQ_CONSIDX_TXQ) |
((cmpconsidx << 16) & 0xFFFF0000));
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_txthresh_adjust(sc)
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
struct sf_softc *sc;
{
u_int32_t txfctl;
u_int8_t txthresh;
txfctl = csr_read_4(sc, SF_TX_FRAMCTL);
txthresh = txfctl & SF_TXFRMCTL_TXTHRESH;
if (txthresh < 0xFF) {
txthresh++;
txfctl &= ~SF_TXFRMCTL_TXTHRESH;
txfctl |= txthresh;
#ifdef DIAGNOSTIC
printf("sf%d: tx underrun, increasing "
"tx threshold to %d bytes\n",
sc->sf_unit, txthresh * 4);
#endif
csr_write_4(sc, SF_TX_FRAMCTL, txfctl);
}
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_intr(arg)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
void *arg;
{
struct sf_softc *sc;
struct ifnet *ifp;
u_int32_t status;
sc = arg;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp = &sc->arpcom.ac_if;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
if (!(csr_read_4(sc, SF_ISR_SHADOW) & SF_ISR_PCIINT_ASSERTED)) {
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/* Disable interrupts. */
csr_write_4(sc, SF_IMR, 0x00000000);
for (;;) {
status = csr_read_4(sc, SF_ISR);
if (status)
csr_write_4(sc, SF_ISR, status);
if (!(status & SF_INTRS))
break;
if (status & SF_ISR_RXDQ1_DMADONE)
sf_rxeof(sc);
Tweak the interrupt handler so that we call the txeof handler more often, to hopefully prevent the TX DMA queue from filling up and never getting flushed.
2001-08-15 17:46:57 +00:00
if (status & SF_ISR_TX_TXDONE ||
status & SF_ISR_TX_DMADONE ||
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
status & SF_ISR_TX_QUEUEDONE)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sf_txeof(sc);
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
if (status & SF_ISR_TX_LOFIFO)
sf_txthresh_adjust(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (status & SF_ISR_ABNORMALINTR) {
if (status & SF_ISR_STATSOFLOW) {
untimeout(sf_stats_update, sc,
sc->sf_stat_ch);
sf_stats_update(sc);
} else
sf_init(sc);
}
}
/* Re-enable interrupts. */
csr_write_4(sc, SF_IMR, SF_INTRS);
if (ifp->if_snd.ifq_head != NULL)
sf_start(ifp);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_init(xsc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
void *xsc;
{
struct sf_softc *sc;
struct ifnet *ifp;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct mii_data *mii;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
int i;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc = xsc;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp = &sc->arpcom.ac_if;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii = device_get_softc(sc->sf_miibus);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sf_stop(sc);
sf_reset(sc);
/* Init all the receive filter registers */
for (i = SF_RXFILT_PERFECT_BASE;
i < (SF_RXFILT_HASH_MAX + 1); i += 4)
csr_write_4(sc, i, 0);
/* Empty stats counter registers. */
for (i = 0; i < sizeof(struct sf_stats)/sizeof(u_int32_t); i++)
csr_write_4(sc, SF_STATS_BASE +
(i + sizeof(u_int32_t)), 0);
/* Init our MAC address */
csr_write_4(sc, SF_PAR0, *(u_int32_t *)(&sc->arpcom.ac_enaddr[0]));
csr_write_4(sc, SF_PAR1, *(u_int32_t *)(&sc->arpcom.ac_enaddr[4]));
sf_setperf(sc, 0, (caddr_t)&sc->arpcom.ac_enaddr);
if (sf_init_rx_ring(sc) == ENOBUFS) {
printf("sf%d: initialization failed: no "
"memory for rx buffers\n", sc->sf_unit);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
sf_init_tx_ring(sc);
csr_write_4(sc, SF_RXFILT, SF_PERFMODE_NORMAL|SF_HASHMODE_WITHVLAN);
/* If we want promiscuous mode, set the allframes bit. */
if (ifp->if_flags & IFF_PROMISC) {
SF_SETBIT(sc, SF_RXFILT, SF_RXFILT_PROMISC);
} else {
SF_CLRBIT(sc, SF_RXFILT, SF_RXFILT_PROMISC);
}
if (ifp->if_flags & IFF_BROADCAST) {
SF_SETBIT(sc, SF_RXFILT, SF_RXFILT_BROAD);
} else {
SF_CLRBIT(sc, SF_RXFILT, SF_RXFILT_BROAD);
}
Close PR# 19904: remember to call sf_setmulti() when initializing the interface so the multicast filter will be programmed correctly.
2000-07-14 19:11:02 +00:00
/*
* Load the multicast filter.
*/
sf_setmulti(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/* Init the completion queue indexes */
csr_write_4(sc, SF_CQ_CONSIDX, 0);
csr_write_4(sc, SF_CQ_PRODIDX, 0);
/* Init the RX completion queue */
csr_write_4(sc, SF_RXCQ_CTL_1,
vtophys(sc->sf_ldata->sf_rx_clist) & SF_RXCQ_ADDR);
SF_SETBIT(sc, SF_RXCQ_CTL_1, SF_RXCQTYPE_3);
/* Init RX DMA control. */
SF_SETBIT(sc, SF_RXDMA_CTL, SF_RXDMA_REPORTBADPKTS);
/* Init the RX buffer descriptor queue. */
csr_write_4(sc, SF_RXDQ_ADDR_Q1,
vtophys(sc->sf_ldata->sf_rx_dlist_big));
csr_write_4(sc, SF_RXDQ_CTL_1, (MCLBYTES << 16) | SF_DESCSPACE_16BYTES);
csr_write_4(sc, SF_RXDQ_PTR_Q1, SF_RX_DLIST_CNT - 1);
/* Init the TX completion queue */
csr_write_4(sc, SF_TXCQ_CTL,
vtophys(sc->sf_ldata->sf_tx_clist) & SF_RXCQ_ADDR);
/* Init the TX buffer descriptor queue. */
csr_write_4(sc, SF_TXDQ_ADDR_HIPRIO,
vtophys(sc->sf_ldata->sf_tx_dlist));
SF_SETBIT(sc, SF_TX_FRAMCTL, SF_TXFRMCTL_CPLAFTERTX);
csr_write_4(sc, SF_TXDQ_CTL,
SF_TXBUFDESC_TYPE0|SF_TXMINSPACE_128BYTES|SF_TXSKIPLEN_8BYTES);
SF_SETBIT(sc, SF_TXDQ_CTL, SF_TXDQCTL_NODMACMP);
/* Enable autopadding of short TX frames. */
SF_SETBIT(sc, SF_MACCFG_1, SF_MACCFG1_AUTOPAD);
/* Enable interrupts. */
csr_write_4(sc, SF_IMR, SF_INTRS);
SF_SETBIT(sc, SF_PCI_DEVCFG, SF_PCIDEVCFG_INTR_ENB);
/* Enable the RX and TX engines. */
SF_SETBIT(sc, SF_GEN_ETH_CTL, SF_ETHCTL_RX_ENB|SF_ETHCTL_RXDMA_ENB);
SF_SETBIT(sc, SF_GEN_ETH_CTL, SF_ETHCTL_TX_ENB|SF_ETHCTL_TXDMA_ENB);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
/*mii_mediachg(mii);*/
sf_ifmedia_upd(ifp);
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp->if_flags |= IFF_RUNNING;
ifp->if_flags &= ~IFF_OACTIVE;
sc->sf_stat_ch = timeout(sf_stats_update, sc, hz);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static int
sf_encap(sc, c, m_head)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
struct sf_tx_bufdesc_type0 *c;
struct mbuf *m_head;
{
int frag = 0;
struct sf_frag *f = NULL;
struct mbuf *m;
m = m_head;
for (m = m_head, frag = 0; m != NULL; m = m->m_next) {
if (m->m_len != 0) {
if (frag == SF_MAXFRAGS)
break;
f = &c->sf_frags[frag];
if (frag == 0)
f->sf_pktlen = m_head->m_pkthdr.len;
f->sf_fraglen = m->m_len;
f->sf_addr = vtophys(mtod(m, vm_offset_t));
frag++;
}
}
if (m != NULL) {
struct mbuf *m_new = NULL;
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (m_new == NULL) {
add missing \n to printf Approved by: gallatin (mentor)
2002-09-09 17:39:48 +00:00
printf("sf%d: no memory for tx list\n", sc->sf_unit);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return(1);
}
if (m_head->m_pkthdr.len > MHLEN) {
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MCLGET(m_new, M_DONTWAIT);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
if (!(m_new->m_flags & M_EXT)) {
m_freem(m_new);
add missing \n to printf Approved by: gallatin (mentor)
2002-09-09 17:39:48 +00:00
printf("sf%d: no memory for tx list\n",
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc->sf_unit);
return(1);
}
}
m_copydata(m_head, 0, m_head->m_pkthdr.len,
mtod(m_new, caddr_t));
m_new->m_pkthdr.len = m_new->m_len = m_head->m_pkthdr.len;
m_freem(m_head);
m_head = m_new;
f = &c->sf_frags[0];
f->sf_fraglen = f->sf_pktlen = m_head->m_pkthdr.len;
f->sf_addr = vtophys(mtod(m_head, caddr_t));
frag = 1;
}
c->sf_mbuf = m_head;
c->sf_id = SF_TX_BUFDESC_ID;
c->sf_fragcnt = frag;
c->sf_intr = 1;
c->sf_caltcp = 0;
c->sf_crcen = 1;
return(0);
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_start(ifp)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct ifnet *ifp;
{
struct sf_softc *sc;
struct sf_tx_bufdesc_type0 *cur_tx = NULL;
struct mbuf *m_head = NULL;
int i, txprod;
sc = ifp->if_softc;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
Tweak the interrupt handler so that we call the txeof handler more often, to hopefully prevent the TX DMA queue from filling up and never getting flushed.
2001-08-15 17:46:57 +00:00
if (!sc->sf_link && ifp->if_snd.ifq_len < 10) {
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
return;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
}
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
if (ifp->if_flags & IFF_OACTIVE) {
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
txprod = csr_read_4(sc, SF_TXDQ_PRODIDX);
i = SF_IDX_HI(txprod) >> 4;
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
if (sc->sf_ldata->sf_tx_dlist[i].sf_mbuf != NULL) {
printf("sf%d: TX ring full, resetting\n", sc->sf_unit);
sf_init(sc);
txprod = csr_read_4(sc, SF_TXDQ_PRODIDX);
i = SF_IDX_HI(txprod) >> 4;
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
while(sc->sf_ldata->sf_tx_dlist[i].sf_mbuf == NULL) {
Still more changes to try to prevent TX lockups. Will wait for one more night of testing before merging to -stable. Also added to code to detect TX underruns and automatically increase the TX threshold to avoid them. Carefully placed diagnostig printf() about this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from confused users, like I always do with the xl and dc drivers.
2001-08-16 00:32:20 +00:00
if (sc->sf_tx_cnt >= (SF_TX_DLIST_CNT - 5)) {
Check the return value of sf_encap() and handle errors accordingly.
2001-01-20 00:50:51 +00:00
ifp->if_flags |= IFF_OACTIVE;
cur_tx = NULL;
break;
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
IF_DEQUEUE(&ifp->if_snd, m_head);
if (m_head == NULL)
break;
cur_tx = &sc->sf_ldata->sf_tx_dlist[i];
Check the return value of sf_encap() and handle errors accordingly.
2001-01-20 00:50:51 +00:00
if (sf_encap(sc, cur_tx, m_head)) {
IF_PREPEND(&ifp->if_snd, m_head);
ifp->if_flags |= IFF_OACTIVE;
cur_tx = NULL;
break;
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/*
* If there's a BPF listener, bounce a copy of this frame
* to him.
*/
o track either_ifattach/ether_ifdetach API changes o use if_input for input packet processing o don't strip the Ethernet header for input packets o use BPF_* macros bpf tapping o call ether_ioctl to handle default ioctl case o track vlan changes Reviewed by: many Approved by: re
2002-11-14 23:49:09 +00:00
BPF_MTAP(ifp, m_head);
As suggested by phk, unconditionalize BPF support in these drivers. Since there are stubs compiled into the kernel if BPF support is not enabled, there aren't any problems with unresolved symbols. The modules in /modules are compiled with BPF support enabled anyway, so the most this will do is bloat GENERIC a little.
1999-09-23 03:32:57 +00:00
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
SF_INC(i, SF_TX_DLIST_CNT);
sc->sf_tx_cnt++;
After one more day of testing, make what I hope are the final tweaks to prevent/workaround TX lockups in this driver. The secret seems to be to not let the TX DMA queue become too full. If we have too many packets in the queue, we should wait for them to drain a bit before trying to queue more. This should prevent the lockup from occurring, and if it does occur, there is special code in sf_start() to kick the NIC in the head and get it going again. Special thanks to Glen Neff for helping me test this fix.
2001-08-16 20:15:16 +00:00
/*
* Don't get the TX DMA queue get too full.
*/
if (sc->sf_tx_cnt > 64)
break;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
}
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
if (cur_tx == NULL) {
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
}
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
/* Transmit */
csr_write_4(sc, SF_TXDQ_PRODIDX,
(txprod & ~SF_TXDQ_PRODIDX_HIPRIO) |
((i << 20) & 0xFFFF0000));
ifp->if_timer = 5;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_stop(sc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_softc *sc;
{
int i;
Remember to clear the IFF_RUNNING and IFF_OACTIVE flags in sf_stop() and sk_stop().
1999-07-25 05:16:05 +00:00
struct ifnet *ifp;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
Remember to clear the IFF_RUNNING and IFF_OACTIVE flags in sf_stop() and sk_stop().
1999-07-25 05:16:05 +00:00
ifp = &sc->arpcom.ac_if;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
untimeout(sf_stats_update, sc, sc->sf_stat_ch);
csr_write_4(sc, SF_GEN_ETH_CTL, 0);
csr_write_4(sc, SF_CQ_CONSIDX, 0);
csr_write_4(sc, SF_CQ_PRODIDX, 0);
csr_write_4(sc, SF_RXDQ_ADDR_Q1, 0);
csr_write_4(sc, SF_RXDQ_CTL_1, 0);
csr_write_4(sc, SF_RXDQ_PTR_Q1, 0);
csr_write_4(sc, SF_TXCQ_CTL, 0);
csr_write_4(sc, SF_TXDQ_ADDR_HIPRIO, 0);
csr_write_4(sc, SF_TXDQ_CTL, 0);
sf_reset(sc);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
sc->sf_link = 0;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
for (i = 0; i < SF_RX_DLIST_CNT; i++) {
if (sc->sf_ldata->sf_rx_dlist_big[i].sf_mbuf != NULL) {
m_freem(sc->sf_ldata->sf_rx_dlist_big[i].sf_mbuf);
sc->sf_ldata->sf_rx_dlist_big[i].sf_mbuf = NULL;
}
}
for (i = 0; i < SF_TX_DLIST_CNT; i++) {
if (sc->sf_ldata->sf_tx_dlist[i].sf_mbuf != NULL) {
m_freem(sc->sf_ldata->sf_tx_dlist[i].sf_mbuf);
sc->sf_ldata->sf_tx_dlist[i].sf_mbuf = NULL;
}
}
Remember to clear the IFF_RUNNING and IFF_OACTIVE flags in sf_stop() and sk_stop().
1999-07-25 05:16:05 +00:00
ifp->if_flags &= ~(IFF_RUNNING|IFF_OACTIVE);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
Remember to clear the IFF_RUNNING and IFF_OACTIVE flags in sf_stop() and sk_stop().
1999-07-25 05:16:05 +00:00
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
/*
* Note: it is important that this function not be interrupted. We
* use a two-stage register access scheme: if we are interrupted in
* between setting the indirect address register and reading from the
* indirect data register, the contents of the address register could
* be changed out from under us.
*/
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_stats_update(xsc)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
void *xsc;
{
struct sf_softc *sc;
struct ifnet *ifp;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
struct mii_data *mii;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct sf_stats stats;
u_int32_t *ptr;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
int i;
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc = xsc;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp = &sc->arpcom.ac_if;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii = device_get_softc(sc->sf_miibus);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ptr = (u_int32_t *)&stats;
for (i = 0; i < sizeof(stats)/sizeof(u_int32_t); i++)
ptr[i] = csr_read_4(sc, SF_STATS_BASE +
(i + sizeof(u_int32_t)));
for (i = 0; i < sizeof(stats)/sizeof(u_int32_t); i++)
csr_write_4(sc, SF_STATS_BASE +
(i + sizeof(u_int32_t)), 0);
ifp->if_collisions += stats.sf_tx_single_colls +
stats.sf_tx_multi_colls + stats.sf_tx_excess_colls;
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
mii_tick(mii);
Do not call mii_pollstat() from within device tick routines; the status information is updated by mii_tick(). Pointed out by: wpaul (a while back)
2001-09-29 19:28:31 +00:00
if (!sc->sf_link && mii->mii_media_status & IFM_ACTIVE &&
IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) {
sc->sf_link++;
if (ifp->if_snd.ifq_head != NULL)
sf_start(ifp);
Modify the Adaptec "starfire" driver to reset the PHY on the MII bus before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).
1999-12-05 20:02:45 +00:00
}
Convert the Adaptec and Winbond drivers to miibus.
1999-08-30 23:08:32 +00:00
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
sc->sf_stat_ch = timeout(sf_stats_update, sc, hz);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_watchdog(ifp)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
struct ifnet *ifp;
{
struct sf_softc *sc;
sc = ifp->if_softc;
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_LOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
ifp->if_oerrors++;
printf("sf%d: watchdog timeout\n", sc->sf_unit);
sf_stop(sc);
sf_reset(sc);
sf_init(sc);
if (ifp->if_snd.ifq_head != NULL)
sf_start(ifp);
First round of converting network drivers from spls to mutexes. This takes care of all the 10/100 and gigE PCI drivers that I've done. Next will be the wireless drivers, then the USB ones. I may pick up some stragglers along the way. I'm sort of playing this by ear: if anyone spots any places where I've screwed up horribly, please let me know.
2000-10-13 17:54:19 +00:00
SF_UNLOCK(sc);
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
return;
}
style: put return values on a line by themselves. fix some paste issues where whitespace was used instead of tabs.
2002-08-23 23:49:02 +00:00
static void
sf_shutdown(dev)
This commit adds device driver support for Adaptec Duralink PCI fast ethernet controllers based on the AIC-6915 "Starfire" controller chip. There are single port, dual port and quad port cards, plus one 100baseFX card. All are 64-bit PCI devices, except one single port model. The Starfire would be a very nice chip were it not for the fact that receive buffers have to be longword aligned. This requires buffer copying in order to achieve proper payload alignment on the alpha. Payload alignment is enforced on both the alpha and x86 platforms. The Starfire has several different DMA descriptor formats and transfer mechanisms. This driver uses frame descriptors for transmission which can address up to 14 packet fragments, and a single fragment descriptor for receive. It also uses the producer/consumer model and completion queues for both transmit and receive. The transmit ring has 128 descriptors and the receive ring has 256. This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus so that it can be compiled as a loadable kernel module. Support for BPF and hardware multicast filtering is included.
1999-07-25 04:32:50 +00:00
device_t dev;
{
struct sf_softc *sc;
sc = device_get_softc(dev);
sf_stop(sc);
return;
}
Reference in New Issue Copy Permalink