d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
8e4e979e1e
freebsd-skq/sys/dev/ata/atapi-cd.c

1914 lines
49 KiB
C
Raw Normal View History

Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/*-
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
* Copyright (c) 1998 - 2005 S<EFBFBD>ren Schmidt <sos@FreeBSD.org>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
Use __FBSDID(). Also some minor style cleanups.
2003-08-24 17:55:58 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
Added undocumented options AAC_DEBUG, ACD_DEBUG, ACPI_MAX_THREADS, ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG, ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES, COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO, NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS, SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG. Start using #! to comment out negative options and ## to comment out broken options. atapi-all.c: Fixed rotted bits that were hiding under ATAPI_DEBUG. atapi-cd.c: #include "opt_ata.h" so that ACD_DEBUG is actually visible. ata/atapi-tape.c #include "opt_ata.h" so that AST_DEBUG is actually visible.
2002-02-15 07:08:44 +00:00
#include "opt_ata.h"
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/param.h>
#include <sys/systm.h>
Provide the interface to atacontrol and associated logic. see atacontrol(8) for more. Also the ATA_ENABLE_ATAPI_DMA, ATA_ENABLE_WC and ATA_ENABLE_TAGS options are gone, use the tuneables listed in ata.4 instead from the loader (this makes it possible to switch off DMA before the driver has to touch the devices on broken hardware).
2001-03-15 15:36:25 +00:00
#include <sys/ata.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/kernel.h>
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
#include <sys/module.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/malloc.h>
KSE Milestone 2 Note ALL MODULES MUST BE RECOMPILED make the kernel aware that there are smaller units of scheduling than the process. (but only allow one thread per process at this time). This is functionally equivalent to teh previousl -current except that there is a thread associated with each process. Sorry john! (your next MFC will be a doosie!) Reviewed by: peter@freebsd.org, dillon@freebsd.org X-MFC after: ha ha ha ha
2001-09-12 08:38:13 +00:00
#include <sys/proc.h>
Separate the struct bio related stuff out of <sys/buf.h> into <sys/bio.h>. <sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall not be made a nested include according to bdes teachings on the subject of nested includes. Diskdrivers and similar stuff below specfs::strategy() should no longer need to include <sys/buf.> unless they need caching of data. Still a few bogus uses of struct buf to track down. Repocopy by: peter
2000-05-05 09:59:14 +00:00
#include <sys/bio.h>
Have another go at the VIA support, this time use the PCI ID form the main component in the southbridge chip to determine which VIA chip we are dealing with. Try to enable DMA on generic controllers that say they has the capability, instead of relying on the BIOS to have set it up.
1999-12-14 10:25:28 +00:00
#include <sys/bus.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/cdio.h>
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
#include <sys/cdrio.h>
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
#include <sys/dvdio.h>
Add support of the DIOCGSECTORSIZE & DIOCGMEDIASIZE ioctl's so that newfs works on dvd-rw/dvd-ram again..
2003-09-11 15:59:16 +00:00
#include <sys/disk.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <sys/fcntl.h>
#include <sys/conf.h>
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
#include <sys/ctype.h>
Overhaul of the timeout/reinit framework. This should clear up most of the leftovers from the old version that really doesn't work anymore. Add a reset function for host-end of the ATA channel. This is needed for the SiI3112 in order to whack it back to reality if a device locks up the SATA interface (thereby preventing that we can reset the device). The result is that ATA now recovers from the timeouts that happens with the SiI3112A and more or less all disks based on old PATA electronics with a Marvell PATA->SATA converter. This includes lots of the popular SATA dongles and the WDC Raptor disks..
2004-01-11 22:08:34 +00:00
#include <sys/sema.h>
Use UMA instead of plain malloc for getting ATA request storage. This gives +10% performance on simple tests, so definitly worth it. A few percent more could be had by not using M_ZERO'd alloc's, but we then need to clear fields all over the place to be safe, and that was deemed not worth the trouble (and it makes life dangerous).
2004-01-14 21:26:35 +00:00
#include <sys/taskqueue.h>
#include <vm/uma.h>
Make the ATA driver compile & work on the sparc64 platform. Initial work & code by tmm. Lots of changes and rearrangements by yours truely to make busdma be a little less a PITA (but I still dont like it).
2002-04-05 13:13:56 +00:00
#include <machine/bus.h>
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
#include <geom/geom.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <dev/ata/ata-all.h>
#include <dev/ata/atapi-cd.h>
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
#include <ata_if.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* prototypes */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void acd_geom_attach(void *, int);
static void acd_geom_detach(void *, int);
static void acd_set_ioparm(device_t);
static void acd_describe(device_t);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static void lba2msf(u_int32_t, u_int8_t *, u_int8_t *, u_int8_t *);
static u_int32_t msf2lba(u_int8_t, u_int8_t, u_int8_t);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
static int acd_geom_access(struct g_provider *, int, int, int);
Pass the file->flags down to geom ioctl handlers. Reject certain ioctls if write permission is not indicated. Bump geom API version. Reported by: Ruben de Groot <mail25@bzerk.org>
2004-12-12 10:09:05 +00:00
static g_ioctl_t acd_geom_ioctl;
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
static void acd_geom_start(struct bio *);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void acd_strategy(struct bio *);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
static void acd_done(struct ata_request *);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void acd_read_toc(device_t);
static int acd_play(device_t, int, int);
static int acd_setchan(device_t, u_int8_t, u_int8_t, u_int8_t, u_int8_t);
static int acd_init_writer(device_t, int);
static int acd_fixate(device_t, int);
static int acd_init_track(device_t, struct cdr_track *);
static int acd_flush(device_t);
static int acd_read_track_info(device_t, int32_t, struct acd_track_info *);
static int acd_get_progress(device_t, int *);
static int acd_send_cue(device_t, struct cdr_cuesheet *);
static int acd_report_key(device_t, struct dvd_authinfo *);
static int acd_send_key(device_t, struct dvd_authinfo *);
static int acd_read_structure(device_t, struct dvd_struct *);
static int acd_tray(device_t, int);
static int acd_blank(device_t, int);
static int acd_prevent_allow(device_t, int);
static int acd_start_stop(device_t, int);
static int acd_pause_resume(device_t, int);
static int acd_mode_sense(device_t, int, caddr_t, int);
static int acd_mode_select(device_t, caddr_t, int);
static int acd_set_speed(device_t, int, int);
static void acd_get_cap(device_t);
static int acd_read_format_caps(device_t, struct cdr_format_capacities *);
static int acd_format(device_t, struct cdr_format_params *);
static int acd_test_ready(device_t);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* internal vars */
Staticize some malloc M_ instances.
2000-12-08 20:09:00 +00:00
static MALLOC_DEFINE(M_ACD, "ACD driver", "ATAPI CD driver buffers");
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
static struct g_class acd_class = {
.name = "ACD",
Tag all geom classes in the tree with a version number.
2004-08-08 07:57:53 +00:00
.version = G_VERSION,
.access = acd_geom_access,
.ioctl = acd_geom_ioctl,
.start = acd_geom_start,
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
};
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
//DECLARE_GEOM_CLASS(acd_class, acd);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
acd_probe(device_t dev)
{
Move the creation of ata_channel child devices to the channel code. This allows to attach to the children (ATA devices) even without a driver being attached. This allows atapi-cam to do its work both with and without the pure ATAPI driver being present. ATA patches by /me ATAPI-cam pathes by Thomas
2005-04-15 10:20:52 +00:00
struct ata_device *atadev = device_get_softc(dev);
if ((atadev->param.config & ATA_PROTO_ATAPI) &&
(atadev->param.config & ATA_ATAPI_TYPE_MASK) == ATA_ATAPI_TYPE_CDROM)
return 0;
else
return ENXIO;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
acd_attach(device_t dev)
{
struct acd_softc *cdp;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!(cdp = malloc(sizeof(struct acd_softc), M_ACD, M_NOWAIT | M_ZERO))) {
device_printf(dev, "out of memory\n");
return ENOMEM;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
cdp->block_size = 2048;
device_set_ivars(dev, cdp);
Change the ata_* methods to use a channel device instead of a controller device. This helps when there is no controller parent to a channel (PPC port).
2005-03-31 15:05:40 +00:00
ATA_SETMODE(device_get_parent(dev), dev);
Reshape the dma code to be a bit more flexible so it can cope with new HW that has new and different demands. Fix a few nits in former commit in this cleanup crusade. Sponsored by: pair.com
2005-05-03 07:55:07 +00:00
ata_controlcmd(dev, ATA_DEVICE_RESET, 0, 0, 0);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_get_cap(dev);
g_post_event(acd_geom_attach, dev, M_WAITOK, NULL);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
/* announce we are here */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_describe(dev);
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
acd_detach(device_t dev)
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
g_waitfor_event(acd_geom_detach, dev, M_WAITOK, NULL);
return 0;
Update the ata driver to take more advantage of newbus, this was needed to make attach/detach of devices work, which is needed for the PCCARD support. (PCCARD support is still not working though, more to come on that) Support the CMD646 chip which is used on many alphas, sadly only in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes. Lots of cosmetic fixes here and there. Sorry for the size of this megapatchfromhell but it was not possible otherwise... newbus patches based on work from: dfr (Doug Rabson)
2000-02-18 20:57:33 +00:00
}
Call the detach function with g_waitfor_event() so that it can access the GEOM topology. There are still issues with not detaching from cam correctly such that upon a device detach there's an invalid pointer dereference from the later call to cam_rescan().
2004-06-21 20:42:03 +00:00
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_shutdown(device_t dev)
{
struct ata_device *atadev = device_get_softc(dev);
if (atadev->param.support.command2 & ATA_SUPPORT_FLUSHCACHE)
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
ata_controlcmd(dev, ATA_FLUSHCACHE, 0, 0, 0);
Call the detach function with g_waitfor_event() so that it can access the GEOM topology. There are still issues with not detaching from cam correctly such that upon a device detach there's an invalid pointer dereference from the later call to cam_rescan().
2004-06-21 20:42:03 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static int
acd_reinit(device_t dev)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
if (((atadev->unit == ATA_MASTER) && !(ch->devices & ATA_ATAPI_MASTER)) ||
((atadev->unit == ATA_SLAVE) && !(ch->devices & ATA_ATAPI_SLAVE))) {
device_set_ivars(dev, NULL);
free(cdp, M_ACD);
return 1;
}
Change the ata_* methods to use a channel device instead of a controller device. This helps when there is no controller parent to a channel (PPC port).
2005-03-31 15:05:40 +00:00
ATA_SETMODE(device_get_parent(dev), dev);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return 0;
Dont call make_dev until we are sure the device is there, this prevents panic'ing when the device is tried accessed later.
2000-03-10 08:09:53 +00:00
}
Make the ATA driver compile & work on the sparc64 platform. Initial work & code by tmm. Lots of changes and rearrangements by yours truely to make busdma be a little less a PITA (but I still dont like it).
2002-04-05 13:13:56 +00:00
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_geom_attach(void *arg, int flag)
Make the ATA driver compile & work on the sparc64 platform. Initial work & code by tmm. Lots of changes and rearrangements by yours truely to make busdma be a little less a PITA (but I still dont like it).
2002-04-05 13:13:56 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_device *atadev = device_get_softc(arg);
struct acd_softc *cdp = device_get_ivars(arg);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
struct g_geom *gp;
struct g_provider *pp;
g_topology_assert();
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
gp = g_new_geomf(&acd_class, "acd%d", device_get_unit(arg));
gp->softc = arg;
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
cdp->gp = gp;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
pp = g_new_providerf(gp, "acd%d", device_get_unit(arg));
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
pp->index = 0;
cdp->pp[0] = pp;
g_error_provider(pp, 0);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
atadev->flags |= ATA_D_MEDIA_CHANGED;
acd_set_ioparm(arg);
Properly change the block_size on different CD media, and use that to calculate the max amount of data in one IO request. Correct the max size on atapi floppies/tapes as well.
2002-07-27 12:22:39 +00:00
}
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_geom_detach(void *arg, int flag)
{
struct acd_softc *cdp = device_get_ivars(arg);
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* signal geom so we dont get any further requests */
g_wither_geom(cdp->gp, ENXIO);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* fail requests on the queue and any thats "in flight" for this device */
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
ata_fail_requests(arg);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
/* dont leave anything behind */
device_set_ivars(arg, NULL);
free(cdp, M_ACD);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
static int
Pass the file->flags down to geom ioctl handlers. Reject certain ioctls if write permission is not indicated. Bump geom API version. Reported by: Ruben de Groot <mail25@bzerk.org>
2004-12-12 10:09:05 +00:00
acd_geom_ioctl(struct g_provider *pp, u_long cmd, void *addr, int fflag, struct thread *td)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_t dev = pp->geom->softc;
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
int error = 0, nocopyout = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
if (!cdp)
return ENXIO;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (atadev->flags & ATA_D_MEDIA_CHANGED) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
switch (cmd) {
case CDIOCRESET:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_test_ready(dev);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
default:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_read_toc(dev);
acd_prevent_allow(dev, 1);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
cdp->flags |= F_LOCKED;
break;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
switch (cmd) {
case CDIOCRESUME:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_pause_resume(dev, 1);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCPAUSE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_pause_resume(dev, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSTART:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_start_stop(dev, 1);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSTOP:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_start_stop(dev, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCALLOW:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_prevent_allow(dev, 0);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
cdp->flags &= ~F_LOCKED;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCPREVENT:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_prevent_allow(dev, 1);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
cdp->flags |= F_LOCKED;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCRESET:
Change the suser() API to take advantage of td_ucred as well as do a general cleanup of the API. The entire API now consists of two functions similar to the pre-KSE API. The suser() function takes a thread pointer as its only argument. The td_ucred member of this thread must be valid so the only valid thread pointers are curthread and a few kernel threads such as thread0. The suser_cred() function takes a pointer to a struct ucred as its first argument and an integer flag as its second argument. The flag is currently only used for the PRISON_ROOT flag. Discussed on: smp@
2002-04-01 21:31:13 +00:00
error = suser(td);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (error)
break;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_test_ready(dev);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCEJECT:
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
if (pp->acr != 1) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EBUSY;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_tray(dev, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCCLOSE:
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
if (pp->acr != 1)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_tray(dev, 1);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOREADTOCHEADER:
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (!cdp->toc.hdr.ending_track) {
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
bcopy(&cdp->toc.hdr, addr, sizeof(cdp->toc.hdr));
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOREADTOCENTRYS:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_read_toc_entry *te = (struct ioc_read_toc_entry *)addr;
struct toc *toc = &cdp->toc;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int starting_track = te->starting_track;
int len;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (!toc->hdr.ending_track) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (te->data_len < sizeof(toc->tab[0]) ||
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
(te->data_len % sizeof(toc->tab[0])) != 0 ||
(te->address_format != CD_MSF_FORMAT &&
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
te->address_format != CD_LBA_FORMAT)) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (!starting_track)
starting_track = toc->hdr.starting_track;
else if (starting_track == 170)
starting_track = toc->hdr.ending_track + 1;
else if (starting_track < toc->hdr.starting_track ||
starting_track > toc->hdr.ending_track + 1) {
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
len = ((toc->hdr.ending_track + 1 - starting_track) + 1) *
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
sizeof(toc->tab[0]);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (te->data_len < len)
len = te->data_len;
if (len > sizeof(toc->tab)) {
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (te->address_format == CD_MSF_FORMAT) {
struct cd_toc_entry *entry;
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(toc = malloc(sizeof(struct toc), M_ACD, M_NOWAIT))) {
error = ENOMEM;
break;
}
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&cdp->toc, toc, sizeof(struct toc));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
entry = toc->tab + (toc->hdr.ending_track + 1 -
toc->hdr.starting_track) + 1;
while (--entry >= toc->tab)
lba2msf(ntohl(entry->addr.lba), &entry->addr.msf.minute,
&entry->addr.msf.second, &entry->addr.msf.frame);
}
error = copyout(toc->tab + starting_track - toc->hdr.starting_track,
te->data, len);
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (te->address_format == CD_MSF_FORMAT)
free(toc, M_ACD);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOREADTOCENTRY:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_read_toc_single_entry *te =
(struct ioc_read_toc_single_entry *)addr;
struct toc *toc = &cdp->toc;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
u_char track = te->track;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (!toc->hdr.ending_track) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (te->address_format != CD_MSF_FORMAT &&
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
te->address_format != CD_LBA_FORMAT) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (!track)
track = toc->hdr.starting_track;
else if (track == 170)
track = toc->hdr.ending_track + 1;
else if (track < toc->hdr.starting_track ||
track > toc->hdr.ending_track + 1) {
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (te->address_format == CD_MSF_FORMAT) {
struct cd_toc_entry *entry;
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(toc = malloc(sizeof(struct toc), M_ACD, M_NOWAIT))) {
error = ENOMEM;
break;
}
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&cdp->toc, toc, sizeof(struct toc));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
entry = toc->tab + (track - toc->hdr.starting_track);
lba2msf(ntohl(entry->addr.lba), &entry->addr.msf.minute,
&entry->addr.msf.second, &entry->addr.msf.frame);
}
bcopy(toc->tab + track - toc->hdr.starting_track,
&te->entry, sizeof(struct cd_toc_entry));
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (te->address_format == CD_MSF_FORMAT)
free(toc, M_ACD);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
#if __FreeBSD_version > 600008
Boot away another stackgap (one of the lest ones in linuxlator/i386) by providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that result has to be placed into kernel space not user space. In the long run more generic solution has to be designed WRT emulating various ioctl()s that operate on userspace buffers, but right now there is only one such ioctl() is emulated, so that it makes little sense. MFC after: 2 weeks
2005-01-30 08:12:37 +00:00
case CDIOCREADSUBCHANNEL_SYSSPACE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
nocopyout = 1;
/* FALLTHROUGH */
#endif
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCREADSUBCHANNEL:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_read_subchannel *args =
(struct ioc_read_subchannel *)addr;
Add more functionality to the CDIOCREADSUBCHANNEL ioctl. PR: 26644
2002-03-16 15:56:54 +00:00
u_int8_t format;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
int8_t ccb[16] = { ATAPI_READ_SUBCHANNEL, 0, 0x40, 1, 0, 0, 0,
sizeof(cdp->subchan)>>8, sizeof(cdp->subchan),
0, 0, 0, 0, 0, 0, 0 };
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
if (args->data_len > sizeof(struct cd_sub_channel_info) ||
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
args->data_len < sizeof(struct cd_sub_channel_header)) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
cosmetics
2003-09-02 15:53:01 +00:00
format = args->data_format;
Add more functionality to the CDIOCREADSUBCHANNEL ioctl. PR: 26644
2002-03-16 15:56:54 +00:00
if ((format != CD_CURRENT_POSITION) &&
(format != CD_MEDIA_CATALOG) && (format != CD_TRACK_INFO)) {
error = EINVAL;
break;
}
ccb[1] = args->address_format & CD_MSF_FORMAT;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if ((error = ata_atapicmd(dev, ccb, (caddr_t)&cdp->subchan,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
sizeof(cdp->subchan), ATA_R_READ, 10)))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
Add more functionality to the CDIOCREADSUBCHANNEL ioctl. PR: 26644
2002-03-16 15:56:54 +00:00
if ((format == CD_MEDIA_CATALOG) || (format == CD_TRACK_INFO)) {
if (cdp->subchan.header.audio_status == 0x11) {
error = EINVAL;
break;
}
ccb[3] = format;
if (format == CD_TRACK_INFO)
ccb[6] = args->track;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if ((error = ata_atapicmd(dev, ccb, (caddr_t)&cdp->subchan,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
sizeof(cdp->subchan),ATA_R_READ,10))){
Add more functionality to the CDIOCREADSUBCHANNEL ioctl. PR: 26644
2002-03-16 15:56:54 +00:00
break;
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Boot away another stackgap (one of the lest ones in linuxlator/i386) by providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that result has to be placed into kernel space not user space. In the long run more generic solution has to be designed WRT emulating various ioctl()s that operate on userspace buffers, but right now there is only one such ioctl() is emulated, so that it makes little sense. MFC after: 2 weeks
2005-01-30 08:12:37 +00:00
if (nocopyout == 0) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = copyout(&cdp->subchan, args->data, args->data_len);
Boot away another stackgap (one of the lest ones in linuxlator/i386) by providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that result has to be placed into kernel space not user space. In the long run more generic solution has to be designed WRT emulating various ioctl()s that operate on userspace buffers, but right now there is only one such ioctl() is emulated, so that it makes little sense. MFC after: 2 weeks
2005-01-30 08:12:37 +00:00
} else {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = 0;
bcopy(&cdp->subchan, args->data, args->data_len);
Boot away another stackgap (one of the lest ones in linuxlator/i386) by providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that result has to be placed into kernel space not user space. In the long run more generic solution has to be designed WRT emulating various ioctl()s that operate on userspace buffers, but right now there is only one such ioctl() is emulated, so that it makes little sense. MFC after: 2 weeks
2005-01-30 08:12:37 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCPLAYMSF:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_play_msf *args = (struct ioc_play_msf *)addr;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
error =
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_play(dev,
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
msf2lba(args->start_m, args->start_s, args->start_f),
msf2lba(args->end_m, args->end_s, args->end_f));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCPLAYBLOCKS:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_play_blocks *args = (struct ioc_play_blocks *)addr;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_play(dev, args->blk, args->blk + args->len);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCPLAYTRACKS:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_play_track *args = (struct ioc_play_track *)addr;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int t1, t2;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (!cdp->toc.hdr.ending_track) {
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (args->end_track < cdp->toc.hdr.ending_track + 1)
++args->end_track;
if (args->end_track > cdp->toc.hdr.ending_track + 1)
args->end_track = cdp->toc.hdr.ending_track + 1;
t1 = args->start_track - cdp->toc.hdr.starting_track;
t2 = args->end_track - cdp->toc.hdr.starting_track;
Dont try to play tracks outside whats on the media. PR 26647
2001-05-30 08:06:57 +00:00
if (t1 < 0 || t2 < 0 ||
t1 > (cdp->toc.hdr.ending_track-cdp->toc.hdr.starting_track)) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
error = EINVAL;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_play(dev, ntohl(cdp->toc.tab[t1].addr.lba),
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
ntohl(cdp->toc.tab[t2].addr.lba));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCGETVOL:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_vol *arg = (struct ioc_vol *)addr;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_AUDIO_PAGE,
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(caddr_t)&cdp->au, sizeof(cdp->au))))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
if (cdp->au.page_code != ATAPI_CDROM_AUDIO_PAGE) {
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
arg->vol[0] = cdp->au.port[0].volume;
arg->vol[1] = cdp->au.port[1].volume;
arg->vol[2] = cdp->au.port[2].volume;
arg->vol[3] = cdp->au.port[3].volume;
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETVOL:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_vol *arg = (struct ioc_vol *)addr;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_AUDIO_PAGE,
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(caddr_t)&cdp->au, sizeof(cdp->au))))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
if (cdp->au.page_code != ATAPI_CDROM_AUDIO_PAGE) {
error = EIO;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_AUDIO_PAGE_MASK,
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(caddr_t)&cdp->aumask,
sizeof(cdp->aumask))))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
cdp->au.data_length = 0;
cdp->au.port[0].channels = CHANNEL_0;
cdp->au.port[1].channels = CHANNEL_1;
cdp->au.port[0].volume = arg->vol[0] & cdp->aumask.port[0].volume;
cdp->au.port[1].volume = arg->vol[1] & cdp->aumask.port[1].volume;
cdp->au.port[2].volume = arg->vol[2] & cdp->aumask.port[2].volume;
cdp->au.port[3].volume = arg->vol[3] & cdp->aumask.port[3].volume;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_mode_select(dev, (caddr_t)&cdp->au, sizeof(cdp->au));
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETPATCH:
{
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct ioc_patch *arg = (struct ioc_patch *)addr;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, arg->patch[0], arg->patch[1],
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
arg->patch[2], arg->patch[3]);
}
Unify prototypes. Cosmetics.
2003-08-25 09:01:49 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETMONO:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, CHANNEL_0|CHANNEL_1, CHANNEL_0|CHANNEL_1, 0,0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETSTEREO:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, CHANNEL_0, CHANNEL_1, 0, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETMUTE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, 0, 0, 0, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETLEFT:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, CHANNEL_0, CHANNEL_0, 0, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDIOCSETRIGHT:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_setchan(dev, CHANNEL_1, CHANNEL_1, 0, 0);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDRIOCBLANK:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_blank(dev, (*(int *)addr));
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
case CDRIOCNEXTWRITEABLEADDR:
{
struct acd_track_info track_info;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_read_track_info(dev, 0xff, &track_info)))
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
if (!track_info.nwa_valid) {
error = EINVAL;
break;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
*(int*)addr = track_info.next_writeable_addr;
}
break;
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
case CDRIOCINITWRITER:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_init_writer(dev, (*(int *)addr));
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
case CDRIOCINITTRACK:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_init_track(dev, (struct cdr_track *)addr);
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
case CDRIOCFLUSH:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_flush(dev);
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
case CDRIOCFIXATE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_fixate(dev, (*(int *)addr));
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
break;
case CDRIOCREADSPEED:
Allow acd(4) and cd(4) to support old behavior for CDRIOC*SPEED ioctls. If the value from the user is less than 177, assume it is a multiple of a single speed CDROM and convert to KB/sec. No complaints from: sos Reviewed by: ken Approved by: re MFC after: 1 day
2002-11-23 22:51:50 +00:00
{
int speed = *(int *)addr;
/* Preserve old behavior: units in multiples of CDROM speed */
if (speed < 177)
speed *= 177;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_set_speed(dev, speed, CDR_MAX_SPEED);
Allow acd(4) and cd(4) to support old behavior for CDRIOC*SPEED ioctls. If the value from the user is less than 177, assume it is a multiple of a single speed CDROM and convert to KB/sec. No complaints from: sos Reviewed by: ken Approved by: re MFC after: 1 day
2002-11-23 22:51:50 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDRIOCWRITESPEED:
First round off updates/fixes to the ATA driver. This moves all chipset specific code to a new file 'ata-chipset.c'. Extensive use of tables and pointers to avoid having the same switch on chipset type in several places, and to allow substituting various functions for different HW arch needs. Added PIO mode setup and all DMA modes. Support for all known SiS chipsets. Thanks to Christoph Kukulies for sponsoring a nice ASUS P4S8X SiS648 based board for this work! Tested on: i386, PC98, alpha and sparc64
2003-02-20 20:02:32 +00:00
{
Allow acd(4) and cd(4) to support old behavior for CDRIOC*SPEED ioctls. If the value from the user is less than 177, assume it is a multiple of a single speed CDROM and convert to KB/sec. No complaints from: sos Reviewed by: ken Approved by: re MFC after: 1 day
2002-11-23 22:51:50 +00:00
int speed = *(int *)addr;
if (speed < 177)
speed *= 177;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_set_speed(dev, CDR_MAX_SPEED, speed);
Allow acd(4) and cd(4) to support old behavior for CDRIOC*SPEED ioctls. If the value from the user is less than 177, assume it is a multiple of a single speed CDROM and convert to KB/sec. No complaints from: sos Reviewed by: ken Approved by: re MFC after: 1 day
2002-11-23 22:51:50 +00:00
}
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDRIOCGETBLOCKSIZE:
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
*(int *)addr = cdp->block_size;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDRIOCSETBLOCKSIZE:
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
cdp->block_size = *(int *)addr;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
pp->sectorsize = cdp->block_size; /* hack for GEOM SOS */
acd_set_ioparm(dev);
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
case CDRIOCGETPROGRESS:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_get_progress(dev, (int *)addr);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
break;
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
case CDRIOCSENDCUE:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_send_cue(dev, (struct cdr_cuesheet *)addr);
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
break;
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
case CDRIOCREADFORMATCAPS:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_read_format_caps(dev, (struct cdr_format_capacities *)addr);
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
break;
case CDRIOCFORMAT:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_format(dev, (struct cdr_format_params *)addr);
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
break;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
case DVDIOCREPORTKEY:
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (cdp->cap.media & MST_READ_DVDROM)
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_report_key(dev, (struct dvd_authinfo *)addr);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
else
error = EINVAL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVDIOCSENDKEY:
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (cdp->cap.media & MST_READ_DVDROM)
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_send_key(dev, (struct dvd_authinfo *)addr);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
else
error = EINVAL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVDIOCREADSTRUCTURE:
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (cdp->cap.media & MST_READ_DVDROM)
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
error = acd_read_structure(dev, (struct dvd_struct *)addr);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
else
error = EINVAL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
default:
Change the way ioctls are issue to ATA. The most prominent part is that its now possible to issue ata_requests directly to say acd0, instead of going through the cumbersome /dev/ata device.
2005-05-16 13:07:27 +00:00
error = ata_device_ioctl(dev, cmd, addr);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return error;
}
static int
acd_geom_access(struct g_provider *pp, int dr, int dw, int de)
{
device_t dev = pp->geom->softc;
struct acd_softc *cdp = device_get_ivars(dev);
struct ata_request *request;
int8_t ccb[16] = { ATAPI_TEST_UNIT_READY, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
int timeout = 60, track;
if (!(request = ata_alloc_request()))
return ENOMEM;
/* wait if drive is not finished loading the medium */
while (timeout--) {
bzero(request, sizeof(struct ata_request));
request->dev = dev;
bcopy(ccb, request->u.atapi.ccb, 16);
request->flags = ATA_R_ATAPI;
request->timeout = 5;
ata_queue_request(request);
if (!request->error &&
(request->u.atapi.sense_data.sense_key == 2 ||
request->u.atapi.sense_data.sense_key == 7) &&
request->u.atapi.sense_data.asc == 4 &&
request->u.atapi.sense_data.ascq == 1)
tsleep(&timeout, PRIBIO, "acdld", hz / 2);
else
break;
}
ata_free_request(request);
if (pp->acr == 0) {
acd_prevent_allow(dev, 1);
cdp->flags |= F_LOCKED;
acd_read_toc(dev);
}
if (dr + pp->acr == 0) {
acd_prevent_allow(dev, 0);
cdp->flags &= ~F_LOCKED;
}
if ((track = pp->index)) {
pp->sectorsize = (cdp->toc.tab[track - 1].control & 4) ? 2048 : 2352;
pp->mediasize = ntohl(cdp->toc.tab[track].addr.lba) -
ntohl(cdp->toc.tab[track - 1].addr.lba);
}
else {
pp->sectorsize = cdp->block_size;
pp->mediasize = cdp->disk_size;
}
pp->mediasize *= pp->sectorsize;
return 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
static void
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
acd_geom_start(struct bio *bp)
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_t dev = bp->bio_to->geom->softc;
struct acd_softc *cdp = device_get_ivars(dev);
Refine the detach/attach code. Proberly fail outstanding bio requests on devices that are detached. This makes it possible to change between disk/cdrom/dvd/whathaveyou in a notebook, just by suspending it, changing the device in the bay (or what you model calls it), unsuspend and the ATA driver will figure out what disappeared and properly fail those, and attach any new devices found.
2001-03-14 12:05:44 +00:00
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
if (bp->bio_cmd != BIO_READ && bp->bio_cmd != BIO_WRITE) {
g_io_deliver(bp, EOPNOTSUPP);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return;
Be less noisy when GEOM probes around during boot if drive contains invalid media (ie empty CD/DVD) Approved by: re@
2003-11-24 14:20:19 +00:00
}
if (bp->bio_cmd == BIO_READ && cdp->disk_size == -1) {
g_io_deliver(bp, EIO);
return;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
/* GEOM classes must do their own request limiting */
if (bp->bio_length <= cdp->iomax) {
bp->bio_pblkno = bp->bio_offset / bp->bio_to->sectorsize;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_strategy(bp);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
}
else {
u_int pos, size = cdp->iomax - cdp->iomax % bp->bio_to->sectorsize;
When breaking up a large request into smaller ones for the strategy routine, create all the child bio objects before starting the requests, rather than starting them as created. This closes a race whereby some number of child operations could complete before the rest were ever created, and prematurely freeing the parent bio. This fixes the panics installing in VMWare and qemu
2005-10-09 21:11:05 +00:00
struct bio *bp2, *first, **next = &first;
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
Fix typo in breaking up requests to size limit. Found by: Peter Edwards <pmedwards@eircom.net>
2003-11-09 10:11:15 +00:00
for (pos = 0; pos < bp->bio_length; pos += size) {
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
if (!(bp2 = g_clone_bio(bp))) {
bp->bio_error = ENOMEM;
break;
}
bp2->bio_done = g_std_done;
bp2->bio_to = bp->bio_to;
bp2->bio_offset += pos;
bp2->bio_data += pos;
bp2->bio_length = MIN(size, bp->bio_length - pos);
bp2->bio_pblkno = bp2->bio_offset / bp2->bio_to->sectorsize;
When breaking up a large request into smaller ones for the strategy routine, create all the child bio objects before starting the requests, rather than starting them as created. This closes a race whereby some number of child operations could complete before the rest were ever created, and prematurely freeing the parent bio. This fixes the panics installing in VMWare and qemu
2005-10-09 21:11:05 +00:00
*next = bp2;
next = (struct bio **)&bp2->bio_driver1;
}
*next = NULL;
while ((bp2 = first) != NULL) {
first = (struct bio *)bp2->bio_driver1;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_strategy(bp2);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
}
}
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_strategy(struct bio *bp)
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_t dev = bp->bio_to->geom->softc;
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
struct ata_request *request;
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
u_int32_t lba, lastlba, count;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
int8_t ccb[16];
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
int track, blocksize;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* reject all queued entries if media changed */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (atadev->flags & ATA_D_MEDIA_CHANGED) {
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
g_io_deliver(bp, EIO);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
bzero(ccb, sizeof(ccb));
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
track = bp->bio_to->index;
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
if (track) {
Fix off by one error in track# calculation.
2000-08-13 09:08:19 +00:00
blocksize = (cdp->toc.tab[track - 1].control & 4) ? 2048 : 2352;
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
lastlba = ntohl(cdp->toc.tab[track].addr.lba);
Fix the size of medium code, the old one failed for DVD's. This might introduce problems on normal CD's (again) sigh...
2001-09-06 17:44:04 +00:00
lba = bp->bio_offset / blocksize;
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
lba += ntohl(cdp->toc.tab[track - 1].addr.lba);
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
}
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
else {
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
blocksize = cdp->block_size;
The size of the disk can't be gotten reliably with the read capacity command, so use the info from the TOC instead.
2001-03-21 14:59:38 +00:00
lastlba = cdp->disk_size;
Fix the size of medium code, the old one failed for DVD's. This might introduce problems on normal CD's (again) sigh...
2001-09-06 17:44:04 +00:00
lba = bp->bio_offset / blocksize;
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
}
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
count = bp->bio_length / blocksize;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
Complete the bio/buf divorce for all code below devfs::strategy Exceptions: Vinum untouched. This means that it cannot be compiled. Greg Lehey is on the case. CCD not converted yet, casts to struct buf (still safe) atapi-cd casts to struct buf to examine B_PHYS
2000-04-15 05:54:02 +00:00
if (bp->bio_cmd == BIO_READ) {
Only read to the end of the select track.
2000-09-18 12:13:32 +00:00
/* if transfer goes beyond range adjust it to be within limits */
if (lba + count > lastlba) {
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
/* if we are entirely beyond EOM return EOF */
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
if (lastlba <= lba) {
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
g_io_deliver(bp, 0);
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
return;
}
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
count = lastlba - lba;
Fix the CD driver so that the last blocks can be read even if a blocksize != 2k is used. Update the timeout code to try fallback to PIO if problems arise in DMA mode.
2000-03-05 16:52:26 +00:00
}
When blocksize is set to 2352, alwas read 2352 bytes. This means it might read more than just data, but that is exactly what we want here (for reading VCD's fx)
2001-01-18 15:20:18 +00:00
switch (blocksize) {
case 2048:
Retry a bit more agressively on the atapi identify. Try to support older systems reporting irq0 for the first channels. Support sharing of the std interrupts (says peter :) ) Dont use READ_CD on normal data reads (2048 bytes), too many old drives doesn't support this command even if the std says "shall" :(, but still use READ_CD on all other blocksizes. Add the geometry to the ad probe, its still usefull.
2000-01-25 20:14:51 +00:00
ccb[0] = ATAPI_READ_BIG;
When blocksize is set to 2352, alwas read 2352 bytes. This means it might read more than just data, but that is exactly what we want here (for reading VCD's fx)
2001-01-18 15:20:18 +00:00
break;
case 2352:
ccb[0] = ATAPI_READ_CD;
ccb[9] = 0xf8;
break;
default:
Retry a bit more agressively on the atapi identify. Try to support older systems reporting irq0 for the first channels. Support sharing of the std interrupts (says peter :) ) Dont use READ_CD on normal data reads (2048 bytes), too many old drives doesn't support this command even if the std says "shall" :(, but still use READ_CD on all other blocksizes. Add the geometry to the ad probe, its still usefull.
2000-01-25 20:14:51 +00:00
ccb[0] = ATAPI_READ_CD;
Make ATAPI CD changer devices work, hopefully better than before.
2000-03-21 13:26:54 +00:00
ccb[9] = 0x10;
Retry a bit more agressively on the atapi identify. Try to support older systems reporting irq0 for the first channels. Support sharing of the std interrupts (says peter :) ) Dont use READ_CD on normal data reads (2048 bytes), too many old drives doesn't support this command even if the std says "shall" :(, but still use READ_CD on all other blocksizes. Add the geometry to the ad probe, its still usefull.
2000-01-25 20:14:51 +00:00
}
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
else
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
ccb[0] = ATAPI_WRITE_BIG;
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
ccb[1] = 0;
ccb[2] = lba>>24;
ccb[3] = lba>>16;
ccb[4] = lba>>8;
ccb[5] = lba;
General cleanup. Dont be so verbose in the probe, only ONE line printed now, to get more info boot verbose. Centralise most printf's in ata-all & ata-dma to use the ata_printf function, it saves alot of codelines. Repeat the identify command if drive fails the first. Protect the timeout functions with splbio. Dont update the transfer details before we are sure the transfer succeded, this way they are proberly retried on errors. Move the handling of next_writeable to userland. Use the READ_CD command to read CD's. That enables us to read _anything_ via the normal read/write interface. This kindof obsoletes the READAUDIO ioctl, but we keep that for now.
2000-01-24 20:45:24 +00:00
ccb[6] = count>>16;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
ccb[7] = count>>8;
ccb[8] = count;
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (!(request = ata_alloc_request())) {
Always return ENOMEM if ata_request_alloc fails so GEOM can dtrt.
2004-01-12 09:33:10 +00:00
g_io_deliver(bp, ENOMEM);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
return;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->dev = dev;
Use the bio field instead of the driver field as intended.
2005-08-17 14:50:18 +00:00
request->bio = bp;
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
bcopy(ccb, request->u.atapi.ccb,
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
(atadev->param.config & ATA_PROTO_MASK) ==
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ATA_PROTO_ATAPI_12 ? 16 : 12);
request->data = bp->bio_data;
request->bytecount = count * blocksize;
request->transfersize = min(request->bytecount, 65534);
request->timeout = (ccb[0] == ATAPI_WRITE_BIG) ? 60 : 30;
request->retries = 2;
request->callback = acd_done;
Use the biotask functionality in GEOM to put finished requests on instead of taskqueue_swi. This shaves from 1 to 10% of the overhead. Overhaul the locking once more, there was a few possible races that are now closed.
2004-01-28 20:38:51 +00:00
request->flags = ATA_R_ATAPI;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (atadev->mode >= ATA_DMA)
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
request->flags |= ATA_R_DMA;
switch (bp->bio_cmd) {
case BIO_READ:
request->flags |= ATA_R_READ;
break;
case BIO_WRITE:
request->flags |= ATA_R_WRITE;
break;
default:
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
device_printf(dev, "unknown BIO operation\n");
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ata_free_request(request);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
g_io_deliver(bp, EIO);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
return;
}
ata_queue_request(request);
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
static void
acd_done(struct ata_request *request)
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
{
Use the bio field instead of the driver field as intended.
2005-08-17 14:50:18 +00:00
struct bio *bp = request->bio;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
/* finish up transfer */
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
bp->bio_completed = request->donecount;
g_io_deliver(bp, request->result);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ata_free_request(request);
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void
acd_set_ioparm(device_t dev)
{
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct acd_softc *cdp = device_get_ivars(dev);
if (ch->dma)
cdp->iomax = min(ch->dma->max_iosize, 65534);
else
cdp->iomax = min(DFLTPHYS, 65534);
}
Make ATAPI CD changer devices work, hopefully better than before.
2000-03-21 13:26:54 +00:00
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
lba2msf(u_int32_t lba, u_int8_t *m, u_int8_t *s, u_int8_t *f)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
lba += 150;
lba &= 0xffffff;
*m = lba / (60 * 75);
lba %= (60 * 75);
*s = lba / 75;
*f = lba % 75;
}
static u_int32_t
msf2lba(u_int8_t m, u_int8_t s, u_int8_t f)
{
return (m * 60 + s) * 75 + f - 150;
}
static void
acd_read_toc(device_t dev)
{
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
struct g_provider *pp;
Fix the size of medium code, the old one failed for DVD's. This might introduce problems on normal CD's (again) sigh...
2001-09-06 17:44:04 +00:00
u_int32_t sizes[2];
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
int8_t ccb[16];
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
int track, ntracks, len;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (acd_test_ready(dev))
Work around the problem that some CDROM drives might return different TOC's for the same media!! that borks up GEOM. Although this looks like bad HW the following patch removes the chance for GEOM panic'ing. Approved by: re@
2003-11-18 15:23:37 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!(atadev->flags & ATA_D_MEDIA_CHANGED))
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
atadev->flags &= ~ATA_D_MEDIA_CHANGED;
Work around the problem that some CDROM drives might return different TOC's for the same media!! that borks up GEOM. Although this looks like bad HW the following patch removes the chance for GEOM panic'ing. Approved by: re@
2003-11-18 15:23:37 +00:00
bzero(&cdp->toc, sizeof(cdp->toc));
bzero(ccb, sizeof(ccb));
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
cdp->disk_size = -1; /* hack for GEOM SOS */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
len = sizeof(struct ioc_toc_header) + sizeof(struct cd_toc_entry);
ccb[0] = ATAPI_READ_TOC;
ccb[7] = len>>8;
ccb[8] = len;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if (ata_atapicmd(dev, ccb, (caddr_t)&cdp->toc, len,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ATA_R_READ | ATA_R_QUIET, 30)) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
bzero(&cdp->toc, sizeof(cdp->toc));
Make ATAPI CD changer devices work, hopefully better than before.
2000-03-21 13:26:54 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
ntracks = cdp->toc.hdr.ending_track - cdp->toc.hdr.starting_track + 1;
if (ntracks <= 0 || ntracks > MAXTRK) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
bzero(&cdp->toc, sizeof(cdp->toc));
Make ATAPI CD changer devices work, hopefully better than before.
2000-03-21 13:26:54 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
len = sizeof(struct ioc_toc_header)+(ntracks+1)*sizeof(struct cd_toc_entry);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_READ_TOC;
ccb[7] = len>>8;
ccb[8] = len;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if (ata_atapicmd(dev, ccb, (caddr_t)&cdp->toc, len,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ATA_R_READ | ATA_R_QUIET, 30)) {
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
bzero(&cdp->toc, sizeof(cdp->toc));
Make ATAPI CD changer devices work, hopefully better than before.
2000-03-21 13:26:54 +00:00
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
cdp->toc.hdr.len = ntohs(cdp->toc.hdr.len);
Add support for accessing individual tracks on a CD. This is done by misusing the device minor a bit to encode the track no there. So to read track #4 just use /dev/acdNt4 where N is the device #. The driver no automatically sets the blocksize (sectorsize) to what the track is set to in the TOC. This has the nice effect that you can now rip audioi tracks by simply doing: dd if=/dev/acdNt2 of=audiotrack2.raw bs=2352 it cant be much simpler than that :) NOTE: the original acdNa & acdNc device still work as usual, except the blocksize is set according to track0.
2000-08-11 09:21:36 +00:00
cdp->block_size = (cdp->toc.tab[0].control & 4) ? 2048 : 2352;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_set_ioparm(dev);
Fix the size of medium code, the old one failed for DVD's. This might introduce problems on normal CD's (again) sigh...
2001-09-06 17:44:04 +00:00
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_READ_CAPACITY;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if (ata_atapicmd(dev, ccb, (caddr_t)sizes, sizeof(sizes),
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ATA_R_READ | ATA_R_QUIET, 30)) {
Fix the size of medium code, the old one failed for DVD's. This might introduce problems on normal CD's (again) sigh...
2001-09-06 17:44:04 +00:00
bzero(&cdp->toc, sizeof(cdp->toc));
return;
}
cdp->disk_size = ntohl(sizes[0]) + 1;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
On open create all the CD physical track devices according to the TOC read from the CD, instead of cloning them when asked to.
2001-03-19 12:02:36 +00:00
for (track = 1; track <= ntracks; track ++) {
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
if (cdp->pp[track] != NULL)
continue;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
pp = g_new_providerf(cdp->gp, "acd%dt%02d", device_get_unit(dev),track);
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
pp->index = track;
cdp->pp[track] = pp;
g_error_provider(pp, 0);
}
for (; track < MAXTRK; track ++) {
if (cdp->pp[track] == NULL)
continue;
cdp->pp[track]->flags |= G_PF_WITHER;
g_orphan_provider(cdp->pp[track], ENXIO);
cdp->pp[track] = NULL;
On open create all the CD physical track devices according to the TOC read from the CD, instead of cloning them when asked to.
2001-03-19 12:02:36 +00:00
}
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
#ifdef ACD_DEBUG
The size of the disk can't be gotten reliably with the read capacity command, so use the info from the TOC instead.
2001-03-21 14:59:38 +00:00
if (cdp->disk_size && cdp->toc.hdr.ending_track) {
Reshape the dma code to be a bit more flexible so it can cope with new HW that has new and different demands. Fix a few nits in former commit in this cleanup crusade. Sponsored by: pair.com
2005-05-03 07:55:07 +00:00
device_printf(dev, "(%d sectors (%d bytes)), %d tracks ",
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
cdp->disk_size, cdp->block_size,
cdp->toc.hdr.ending_track-cdp->toc.hdr.starting_track+1);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
if (cdp->toc.tab[0].control & 4)
The size of the disk can't be gotten reliably with the read capacity command, so use the info from the TOC instead.
2001-03-21 14:59:38 +00:00
printf("%dMB\n", cdp->disk_size / 512);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
else
The size of the disk can't be gotten reliably with the read capacity command, so use the info from the TOC instead.
2001-03-21 14:59:38 +00:00
printf("%d:%d audio\n",
cdp->disk_size / 75 / 60, cdp->disk_size / 75 % 60);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
}
#endif
Add DVD-RAM support. The driver constructs a fake disklabel that makes the 'a' partition cover the entire DVD-RAM disk. This cannot be changed from the user side. This solution was chosen because most DVD-RAM will have a UDF (or until we have that CD9660) filesystem on it covering the entire disk, its not really thought as a real random access device. This might change over time, but for now this is what we have, and it is compatible with CDROM's etc, that makes using the minidisk subsystem less than ideal, because of !modulo BDEV_SIZE blocks.
2000-02-29 22:00:53 +00:00
}
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_play(device_t dev, int start, int end)
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
{
int8_t ccb[16];
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_PLAY_MSF;
lba2msf(start, &ccb[3], &ccb[4], &ccb[5]);
lba2msf(end, &ccb[6], &ccb[7], &ccb[8]);
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 10);
Use PLAY_MSF instead of PLAY_BIG when doing audio play. The fixes the problem of PLAY_BIG not being implemented on some modern drives. The problem now is that some old drives use BSD encoding in the MSF case, which they dont tell, and which is also not according to spec *sigh*. Hopefully there are not too many of those still alive, or I hereby grant license to kill the firmware writers that wrote the mess.
2001-03-27 10:22:50 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_setchan(device_t dev, u_int8_t c0, u_int8_t c1, u_int8_t c2, u_int8_t c3)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct acd_softc *cdp = device_get_ivars(dev);
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_AUDIO_PAGE, (caddr_t)&cdp->au,
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
sizeof(cdp->au))))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (cdp->au.page_code != ATAPI_CDROM_AUDIO_PAGE)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return EIO;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
cdp->au.data_length = 0;
cdp->au.port[0].channels = c0;
cdp->au.port[1].channels = c1;
cdp->au.port[2].channels = c2;
cdp->au.port[3].channels = c3;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return acd_mode_select(dev, (caddr_t)&cdp->au, sizeof(cdp->au));
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_init_writer(device_t dev, int test_write)
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
{
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
int8_t ccb[16];
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_REZERO;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
ata_atapicmd(dev, ccb, NULL, 0, ATA_R_QUIET, 60);
Finally commit some of the minor things I've collected over the last month(s): Add tagged queueing support for new IBM drives. Add support for Yet Another Promise ATA 100 chip. Flush disk cache on close. Dont flush the disk cache on BIO_ORDERED anymore. Cleanup the tests for DMA on ATAPI devices. Allow to share ALL irq's even the std irg 14 & 15. Fix calculation bug in end of media code on CD's. Add REZERO on opening a CDR/CDRW. Cleanup ataioctl a bit.
2001-08-21 11:35:47 +00:00
ccb[0] = ATAPI_SEND_OPC_INFO;
ccb[1] = 0x01;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
ata_atapicmd(dev, ccb, NULL, 0, ATA_R_QUIET, 30);
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
return 0;
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_fixate(device_t dev, int multisession)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct acd_softc *cdp = device_get_ivars(dev);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
int8_t ccb[16] = { ATAPI_CLOSE_TRACK, 0x01, 0x02, 0, 0, 0, 0, 0,
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
0, 0, 0, 0, 0, 0, 0, 0 };
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
int timeout = 5*60*2;
Try a little harder to catch when fixate finishes. On the <QSI CD-RW/DVD-ROM SBW-242> that failed causing burncd to wait forever...
2003-12-07 23:15:22 +00:00
int error, dummy;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
struct write_param param;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_WRITE_PARAMETERS_PAGE,
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
(caddr_t)&param, sizeof(param))))
return error;
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
param.data_length = 0;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
if (multisession)
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
param.session_type = CDR_SESS_MULTI;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
else
Major update of the ATA RAID code, part 1: Overhaul of the attach/detach code and structures, there were some nasty bugs in the old implementation. This made it possible to collapse the ATA/ATAPI device control structures into one generic structure. A note here, the kernel is NOT ready for detach of active devices, it fails all over in random places, but for inactive devices it works. However for ATA RAID this works, since the RAID abstration layer insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the physical disks. Proberly detect the RAID's from the BIOS, and mark critical RAID1 arrays as such, but continue if there is enough of the mirror left to do so. Properly fail arrays on a live system. For RAID0 that means return EIO, and for RAID1 it means continue on the still working part of the mirror if possible, else return EIO. If the state changes, log this to the console. Allow for Promise & Highpoint controllers/arrays to coexist on the same machine. It is not possible to distribute arrays over different makes of controllers though. If Promise SuperSwap enclosures are used, signal disk state on the status LED on the front. Misc fixes that I had lying around for various minor bugs. Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
param.session_type = CDR_SESS_NONE;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_select(dev, (caddr_t)&param, param.page_length + 10)))
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
return error;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
if (error)
return error;
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
/* some drives just return ready, wait for the expected fixate time */
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_test_ready(dev)) != EBUSY) {
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
timeout = timeout / (cdp->cap.cur_write_speed / 177);
tsleep(&error, PRIBIO, "acdfix", timeout * hz / 2);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return acd_test_ready(dev);
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
}
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
while (timeout-- > 0) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_get_progress(dev, &dummy)))
Try a little harder to catch when fixate finishes. On the <QSI CD-RW/DVD-ROM SBW-242> that failed causing burncd to wait forever...
2003-12-07 23:15:22 +00:00
return error;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_test_ready(dev)) != EBUSY)
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
return error;
Try a little harder to catch when fixate finishes. On the <QSI CD-RW/DVD-ROM SBW-242> that failed causing burncd to wait forever...
2003-12-07 23:15:22 +00:00
tsleep(&error, PRIBIO, "acdcld", hz / 2);
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
}
return EIO;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_init_track(device_t dev, struct cdr_track *track)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct acd_softc *cdp = device_get_ivars(dev);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
struct write_param param;
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_WRITE_PARAMETERS_PAGE,
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
(caddr_t)&param, sizeof(param))))
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
return error;
cosmetic changes only.
2000-01-29 14:10:59 +00:00
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
param.data_length = 0;
cosmetic changes only.
2000-01-29 14:10:59 +00:00
param.page_code = ATAPI_CDROM_WRITE_PARAMETERS_PAGE;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
param.page_length = 0x32;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
param.test_write = track->test_write ? 1 : 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
param.write_type = CDR_WTYPE_TRACK;
Update to support the NEC NR-7500A burners.
2001-05-30 07:28:57 +00:00
param.session_type = CDR_SESS_NONE;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.fp = 0;
param.packet_size = 0;
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (cdp->cap.capabilities & MST_BURNPROOF)
Add support for using BurnProff(tm) on drives that support it. This is experimental as I dont have such a drive, reports welcome!!
2001-01-04 12:43:39 +00:00
param.burnproof = 1;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
switch (track->datablock_type) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_RAW:
if (track->preemp)
param.track_mode = CDR_TMODE_AUDIO_PREEMP;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
else
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
param.track_mode = CDR_TMODE_AUDIO;
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2352;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_RAW;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.session_format = CDR_SESS_CDROM;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_ROM_MODE1:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2048;
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_ROM_MODE1;
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
param.session_format = CDR_SESS_CDROM;
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_ROM_MODE2:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2336;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_ROM_MODE2;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.session_format = CDR_SESS_CDROM;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_XA_MODE1:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2048;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_XA_MODE1;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.session_format = CDR_SESS_CDROM_XA;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_XA_MODE2_F1:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2056;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_XA_MODE2_F1;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.session_format = CDR_SESS_CDROM_XA;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_XA_MODE2_F2:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2324;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_XA_MODE2_F2;
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
param.session_format = CDR_SESS_CDROM_XA;
break;
New ATAPI burner utility API, replaces the wormio API.
2000-01-06 22:50:02 +00:00
case CDR_DB_XA_MODE2_MIX:
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
cdp->block_size = 2332;
param.track_mode = CDR_TMODE_DATA;
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
param.datablock_type = CDR_DB_XA_MODE2_MIX;
Fix timeout handeling and add retry counts. Add HPT366 probe message (but no real support yet), Add CDR support for several diffenrent blocktypes, also close disk as a multisession CD.
1999-09-24 12:36:10 +00:00
param.session_format = CDR_SESS_CDROM_XA;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
break;
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_set_ioparm(dev);
return acd_mode_select(dev, (caddr_t)&param, param.page_length + 10);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_flush(device_t dev)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Fix for the HP burners (and possibly other broken drives to) that fails to proberly close the disk. The problem seems to be that the HP burners sometimes return ready when they actually are not, the solution is to not use immediate mode on the closing commands. This is suboptimal for real burners, in that they now hog the ATA bus for possibly minutes, where its really not nessesary, *sigh*.
2000-05-01 07:30:28 +00:00
int8_t ccb[16] = { ATAPI_SYNCHRONIZE_CACHE, 0, 0, 0, 0, 0, 0, 0,
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
0, 0, 0, 0, 0, 0, 0, 0 };
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, ATA_R_QUIET, 60);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_read_track_info(device_t dev, int32_t lba, struct acd_track_info *info)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
int8_t ccb[16] = { ATAPI_READ_TRACK_INFO, 1,
GEOM'ify atapi-cd. Original patch by phk, subtle changes by me.
2003-11-01 09:44:33 +00:00
lba>>24, lba>>16, lba>>8, lba, 0,
sizeof(*info)>>8, sizeof(*info),
0, 0, 0, 0, 0, 0, 0 };
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
if ((error = ata_atapicmd(dev, ccb, (caddr_t)info, sizeof(*info),
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ATA_R_READ, 30)))
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
return error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
info->track_start_addr = ntohl(info->track_start_addr);
info->next_writeable_addr = ntohl(info->next_writeable_addr);
info->free_blocks = ntohl(info->free_blocks);
info->fixed_packet_size = ntohl(info->fixed_packet_size);
info->track_length = ntohl(info->track_length);
return 0;
}
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_get_progress(device_t dev, int *finished)
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
{
Try to fix the problem with burncd blank not seeing the end of the blank operation.
2002-12-17 16:27:45 +00:00
int8_t ccb[16] = { ATAPI_READ_CAPACITY, 0, 0, 0, 0, 0, 0, 0,
Fix the problem with some drives not reporting back when the are busy blanking and erasing CD-RW media. This fixes burncd's premature returns from blanking/erasing that caused trouble.
2001-03-23 20:55:28 +00:00
0, 0, 0, 0, 0, 0, 0, 0 };
Fix getting progress data for some device in yet another way. Take advantage of the new autosense logic.
2004-03-02 14:03:43 +00:00
struct ata_request *request;
Try to fix the problem with burncd blank not seeing the end of the blank operation.
2002-12-17 16:27:45 +00:00
int8_t dummy[8];
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
Fix getting progress data for some device in yet another way. Take advantage of the new autosense logic.
2004-03-02 14:03:43 +00:00
if (!(request = ata_alloc_request()))
return ENOMEM;
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
request->dev = dev;
Fix getting progress data for some device in yet another way. Take advantage of the new autosense logic.
2004-03-02 14:03:43 +00:00
bcopy(ccb, request->u.atapi.ccb, 16);
request->data = dummy;
request->bytecount = sizeof(dummy);
request->transfersize = min(request->bytecount, 65534);
request->flags = ATA_R_ATAPI | ATA_R_READ;
request->timeout = 30;
ata_queue_request(request);
if (!request->error && request->u.atapi.sense_data.sksv)
*finished = ((request->u.atapi.sense_data.sk_specific2 |
(request->u.atapi.sense_data.sk_specific1<<8))*100)/65535;
Fix the problem with some drives not reporting back when the are busy blanking and erasing CD-RW media. This fixes burncd's premature returns from blanking/erasing that caused trouble.
2001-03-23 20:55:28 +00:00
else
*finished = 0;
Fix getting progress data for some device in yet another way. Take advantage of the new autosense logic.
2004-03-02 14:03:43 +00:00
ata_free_request(request);
Fix the problem with some drives not reporting back when the are busy blanking and erasing CD-RW media. This fixes burncd's premature returns from blanking/erasing that caused trouble.
2001-03-23 20:55:28 +00:00
return 0;
Update the burncd interface a bit, dont block the ATA channel on blank & fixate commands and provide a progress interface for the blank command (for now)
2000-12-26 11:55:44 +00:00
}
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_send_cue(device_t dev, struct cdr_cuesheet *cuesheet)
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct acd_softc *cdp = device_get_ivars(dev);
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
struct write_param param;
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
int8_t ccb[16] = { ATAPI_SEND_CUE_SHEET, 0, 0, 0, 0, 0,
cuesheet->len>>16, cuesheet->len>>8, cuesheet->len,
0, 0, 0, 0, 0, 0, 0 };
int8_t *buffer;
int32_t error;
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_sense(dev, ATAPI_CDROM_WRITE_PARAMETERS_PAGE,
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
(caddr_t)&param, sizeof(param))))
return error;
Misc cleanups. Pointed out by: phk/flexelint
2002-10-01 15:21:57 +00:00
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
param.data_length = 0;
param.page_code = ATAPI_CDROM_WRITE_PARAMETERS_PAGE;
param.page_length = 0x32;
param.test_write = cuesheet->test_write ? 1 : 0;
param.write_type = CDR_WTYPE_SESSION;
Allow setting the CD type on cue sheets
2001-12-04 21:39:34 +00:00
param.session_type = cuesheet->session_type;
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
param.fp = 0;
param.packet_size = 0;
param.track_mode = CDR_TMODE_AUDIO;
param.datablock_type = CDR_DB_RAW;
Allow setting the CD type on cue sheets
2001-12-04 21:39:34 +00:00
param.session_format = cuesheet->session_format;
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
if (cdp->cap.capabilities & MST_BURNPROOF)
Allow setting the CD type on cue sheets
2001-12-04 21:39:34 +00:00
param.burnproof = 1;
Misc cleanups. Pointed out by: phk/flexelint
2002-10-01 15:21:57 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if ((error = acd_mode_select(dev, (caddr_t)&param, param.page_length + 10)))
Change the way DAO/TAO mode is init'ed. Fix a bogon introduced in the previous commit, that broke CDIOREADSUBCHANNEL.
2001-10-01 14:59:52 +00:00
return error;
Misc cleanups. Pointed out by: phk/flexelint
2002-10-01 15:21:57 +00:00
if (!(buffer = malloc(cuesheet->len, M_ACD, M_NOWAIT)))
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
return ENOMEM;
Misc cleanups. Pointed out by: phk/flexelint
2002-10-01 15:21:57 +00:00
Reshape the dma code to be a bit more flexible so it can cope with new HW that has new and different demands. Fix a few nits in former commit in this cleanup crusade. Sponsored by: pair.com
2005-05-03 07:55:07 +00:00
if (!(error = copyin(cuesheet->entries, buffer, cuesheet->len)))
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, buffer, cuesheet->len, 0, 30);
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
free(buffer, M_ACD);
return error;
}
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_report_key(device_t dev, struct dvd_authinfo *ai)
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
{
Dont alloc size 0 buffers.
2004-02-21 18:30:03 +00:00
struct dvd_miscauth *d = NULL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
u_int32_t lba = 0;
int16_t length;
int8_t ccb[16];
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int error;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
switch (ai->format) {
case DVD_REPORT_AGID:
case DVD_REPORT_ASF:
case DVD_REPORT_RPC:
length = 8;
break;
case DVD_REPORT_KEY1:
length = 12;
break;
case DVD_REPORT_TITLE_KEY:
length = 12;
lba = ai->lba;
break;
case DVD_REPORT_CHALLENGE:
length = 16;
break;
case DVD_INVALIDATE_AGID:
length = 0;
break;
default:
return EINVAL;
}
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_REPORT_KEY;
ccb[2] = (lba >> 24) & 0xff;
ccb[3] = (lba >> 16) & 0xff;
ccb[4] = (lba >> 8) & 0xff;
ccb[5] = lba & 0xff;
ccb[8] = (length >> 8) & 0xff;
ccb[9] = length & 0xff;
ccb[10] = (ai->agid << 6) | ai->format;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
Dont alloc size 0 buffers.
2004-02-21 18:30:03 +00:00
if (length) {
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(d = malloc(length, M_ACD, M_NOWAIT | M_ZERO)))
return ENOMEM;
Dont alloc size 0 buffers.
2004-02-21 18:30:03 +00:00
d->length = htons(length - 2);
}
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, (caddr_t)d, length,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
ai->format == DVD_INVALIDATE_AGID ? 0 : ATA_R_READ,10);
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (error) {
free(d, M_ACD);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
return error;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
}
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
switch (ai->format) {
case DVD_REPORT_AGID:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
ai->agid = d->data[3] >> 6;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_REPORT_CHALLENGE:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&d->data[0], &ai->keychal[0], 10);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_REPORT_KEY1:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&d->data[0], &ai->keychal[0], 5);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_REPORT_TITLE_KEY:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
ai->cpm = (d->data[0] >> 7);
ai->cp_sec = (d->data[0] >> 6) & 0x1;
ai->cgms = (d->data[0] >> 4) & 0x3;
bcopy(&d->data[1], &ai->keychal[0], 5);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_REPORT_ASF:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
ai->asf = d->data[3] & 1;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_REPORT_RPC:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
ai->reg_type = (d->data[0] >> 6);
ai->vend_rsts = (d->data[0] >> 3) & 0x7;
ai->user_rsts = d->data[0] & 0x7;
ai->region = d->data[1];
ai->rpc_scheme = d->data[2];
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_INVALIDATE_AGID:
break;
default:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
error = EINVAL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
}
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
free(d, M_ACD);
return error;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_send_key(device_t dev, struct dvd_authinfo *ai)
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
{
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
struct dvd_miscauth *d;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
int16_t length;
int8_t ccb[16];
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
int error;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
switch (ai->format) {
case DVD_SEND_CHALLENGE:
length = 16;
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(d = malloc(length, M_ACD, M_NOWAIT | M_ZERO)))
return ENOMEM;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(ai->keychal, &d->data[0], 10);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_SEND_KEY2:
length = 12;
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(d = malloc(length, M_ACD, M_NOWAIT | M_ZERO)))
return ENOMEM;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&ai->keychal[0], &d->data[0], 5);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_SEND_RPC:
length = 8;
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(d = malloc(length, M_ACD, M_NOWAIT | M_ZERO)))
return ENOMEM;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
d->data[0] = ai->region;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
default:
return EINVAL;
}
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_SEND_KEY;
ccb[8] = (length >> 8) & 0xff;
ccb[9] = length & 0xff;
ccb[10] = (ai->agid << 6) | ai->format;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
d->length = htons(length - 2);
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, (caddr_t)d, length, 0, 10);
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
free(d, M_ACD);
return error;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_read_structure(device_t dev, struct dvd_struct *s)
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
{
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
struct dvd_miscauth *d;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
u_int16_t length;
int8_t ccb[16];
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
int error = 0;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
switch(s->format) {
case DVD_STRUCT_PHYSICAL:
length = 21;
break;
case DVD_STRUCT_COPYRIGHT:
length = 8;
break;
case DVD_STRUCT_DISCKEY:
length = 2052;
break;
case DVD_STRUCT_BCA:
length = 192;
break;
case DVD_STRUCT_MANUFACT:
length = 2052;
break;
case DVD_STRUCT_DDS:
case DVD_STRUCT_PRERECORDED:
case DVD_STRUCT_UNIQUEID:
case DVD_STRUCT_LIST:
case DVD_STRUCT_CMI:
case DVD_STRUCT_RMD_LAST:
case DVD_STRUCT_RMD_RMA:
case DVD_STRUCT_DCB:
return ENOSYS;
default:
return EINVAL;
}
Properly check malloc returns.
2004-08-24 10:39:00 +00:00
if (!(d = malloc(length, M_ACD, M_NOWAIT | M_ZERO)))
return ENOMEM;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
d->length = htons(length - 2);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
bzero(ccb, sizeof(ccb));
ccb[0] = ATAPI_READ_STRUCTURE;
ccb[6] = s->layer_num;
ccb[7] = s->format;
ccb[8] = (length >> 8) & 0xff;
ccb[9] = length & 0xff;
ccb[10] = s->agid << 6;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, (caddr_t)d, length, ATA_R_READ, 30);
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
if (error) {
free(d, M_ACD);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
return error;
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
}
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
switch (s->format) {
case DVD_STRUCT_PHYSICAL: {
struct dvd_layer *layer = (struct dvd_layer *)&s->data[0];
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
layer->book_type = d->data[0] >> 4;
layer->book_version = d->data[0] & 0xf;
layer->disc_size = d->data[1] >> 4;
layer->max_rate = d->data[1] & 0xf;
layer->nlayers = (d->data[2] >> 5) & 3;
layer->track_path = (d->data[2] >> 4) & 1;
layer->layer_type = d->data[2] & 0xf;
layer->linear_density = d->data[3] >> 4;
layer->track_density = d->data[3] & 0xf;
layer->start_sector = d->data[5] << 16 | d->data[6] << 8 | d->data[7];
layer->end_sector = d->data[9] << 16 | d->data[10] << 8 | d->data[11];
layer->end_sector_l0 = d->data[13] << 16 | d->data[14] << 8|d->data[15];
layer->bca = d->data[16] >> 7;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
}
case DVD_STRUCT_COPYRIGHT:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
s->cpst = d->data[0];
s->rmi = d->data[0];
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_STRUCT_DISCKEY:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
bcopy(&d->data[0], &s->data[0], 2048);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_STRUCT_BCA:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
s->length = ntohs(d->length);
bcopy(&d->data[0], &s->data[0], s->length);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
case DVD_STRUCT_MANUFACT:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
s->length = ntohs(d->length);
bcopy(&d->data[0], &s->data[0], s->length);
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
break;
default:
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
error = EINVAL;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
}
Overhaul to minimize stack usage, in some places >2K was used on the stack *blush*...
2001-09-20 15:25:36 +00:00
free(d, M_ACD);
return error;
Commit the kernel part of our DVD support. Nothing much to say really, its just a number of new ioctl's, the rest is done in userland.
1999-12-07 22:25:28 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_tray(device_t dev, int close)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
Redo the code that handles eject/close.
2003-10-12 13:11:57 +00:00
int error = ENODEV;
if (cdp->cap.mechanism & MST_EJECT) {
if (close) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!(error = acd_start_stop(dev, 3))) {
acd_read_toc(dev);
acd_prevent_allow(dev, 1);
Redo the code that handles eject/close.
2003-10-12 13:11:57 +00:00
cdp->flags |= F_LOCKED;
}
}
else {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_start_stop(dev, 0);
acd_prevent_allow(dev, 0);
Redo the code that handles eject/close.
2003-10-12 13:11:57 +00:00
cdp->flags &= ~F_LOCKED;
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
atadev->flags |= ATA_D_MEDIA_CHANGED;
error = acd_start_stop(dev, 2);
Redo the code that handles eject/close.
2003-10-12 13:11:57 +00:00
}
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Redo the code that handles eject/close.
2003-10-12 13:11:57 +00:00
return error;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_blank(device_t dev, int blanktype)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct ata_device *atadev = device_get_softc(dev);
Add session argument to *close_disk, allowing to set session type on fixate. Add support for different blank/erase types. Update headers.
2001-01-10 19:19:47 +00:00
int8_t ccb[16] = { ATAPI_BLANK, 0x10 | (blanktype & 0x7), 0, 0, 0, 0, 0, 0,
Nine'th update to the new ATA/ATAPI driver: The atapi subsystem has gotten better error handeling and timeouts, it also tries a REQUEST SENSE command when devices returns errors, to give a little more info as to what went wrong. It might be a little verbose for now, but I'm interested in as much feedback on errors as possible, especially timeouts, as I'm a bit in doubt if I've chosen resonable default values everywhere. The disk driver has been changed a bit to prepare for tagged queing, which is next on my list. The disk driver has grown a dump routine, I got one implementation from Darrell Anderson <anderson@cs.duke.edu> which also did partial dumps (usefull on big memory machines) I left out the partial stuff for now, and changed the rest alot to fit into the new ad_request framework. Some minor cleanups and rearrangements as well. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, again you have been warned :) Notebook owners should be carefull that their machines dont suspend as this might cause trouble... But please tell me how it works for you! Enjoy! -Søren
1999-06-25 09:03:07 +00:00
0, 0, 0, 0, 0, 0, 0, 0 };
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
atadev->flags |= ATA_D_MEDIA_CHANGED;
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_prevent_allow(device_t dev, int lock)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
int8_t ccb[16] = { ATAPI_PREVENT_ALLOW, 0, 0, 0, lock,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_start_stop(device_t dev, int start)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
int8_t ccb[16] = { ATAPI_START_STOP, 0, 0, 0, start,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_pause_resume(device_t dev, int pause)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
int8_t ccb[16] = { ATAPI_PAUSE, 0, 0, 0, 0, 0, 0, 0, pause,
0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_mode_sense(device_t dev, int page, caddr_t pagebuf, int pagesize)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
int8_t ccb[16] = { ATAPI_MODE_SENSE_BIG, 0, page, 0, 0, 0, 0,
pagesize>>8, pagesize, 0, 0, 0, 0, 0, 0, 0 };
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
int error;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, pagebuf, pagesize, ATA_R_READ, 10);
Add support for the HPT366 chip, this is used on the Abit boards and their HotRod controller and on SIIG PCI ultra DMA controller. These changes also made lots of the Promise code go away, its all much more generic this way. Get rid of atapi_immed_cmd, instead use the queue to move atapi commands from interrupt context if nessesary, the entire atapi layer has gotten an overhaul. Lots of fixes to utililize the new features in subr_disk.c etc, and get rid of the last biots of softc arrays in the drivers, the only one left is atadevices which cannot easily go away (yet). Use our own malloc names, its a lot easier to track memory usage this way. General cleanup overall.
1999-10-09 19:57:13 +00:00
return error;
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_mode_select(device_t dev, caddr_t pagebuf, int pagesize)
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
{
int8_t ccb[16] = { ATAPI_MODE_SELECT_BIG, 0x10, 0, 0, 0, 0, 0,
pagesize>>8, pagesize, 0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, pagebuf, pagesize, 0, 30);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add support for tagged queuing on ATA drives. There is only support for IBM's DPTA and DTLA series of drives (no other disk vendors are known to support this) on non-Promise controllers (promise controllers lockup when given the tagged queuing specific commands). It gives especially master/slave comboes about 5% better performance. Add support for the Promise ATA100 OEM chip (pdc20265) Add support for the Cyrix 5530 Change the way status is read from the drives, use the alternate status reg when possible. Better support for DEVFS, the acdXtY devices are now created when needed. Lots of little cleanups.
2000-09-19 11:08:39 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_set_speed(device_t dev, int rdspeed, int wrspeed)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
{
Add kernel side support for DAO burning.
2001-09-10 11:43:20 +00:00
int8_t ccb[16] = { ATAPI_SET_SPEED, 0, rdspeed >> 8, rdspeed,
wrspeed >> 8, wrspeed, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
int error;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
if (!error)
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_get_cap(dev);
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
return error;
}
static void
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_get_cap(device_t dev)
On burners that return faulty ready on fixate, wait for the expected fixate time before returning. Dont print error messages to the console on READ_TOC on a blank media.
2001-04-05 11:17:33 +00:00
{
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
struct acd_softc *cdp = device_get_ivars(dev);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
int count;
/* get drive capabilities, some bugridden drives needs this repeated */
for (count = 0 ; count < 5 ; count++) {
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
if (!acd_mode_sense(dev, ATAPI_CDROM_CAP_PAGE,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
(caddr_t)&cdp->cap, sizeof(cdp->cap)) &&
cdp->cap.page_code == ATAPI_CDROM_CAP_PAGE) {
cdp->cap.max_read_speed = ntohs(cdp->cap.max_read_speed);
cdp->cap.cur_read_speed = ntohs(cdp->cap.cur_read_speed);
cdp->cap.max_write_speed = ntohs(cdp->cap.max_write_speed);
cdp->cap.cur_write_speed = max(ntohs(cdp->cap.cur_write_speed),177);
cdp->cap.max_vol_levels = ntohs(cdp->cap.max_vol_levels);
cdp->cap.buf_size = ntohs(cdp->cap.buf_size);
}
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_read_format_caps(device_t dev, struct cdr_format_capacities *caps)
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
{
int8_t ccb[16] = { ATAPI_READ_FORMAT_CAPACITIES, 0, 0, 0, 0, 0, 0,
(sizeof(struct cdr_format_capacities) >> 8) & 0xff,
sizeof(struct cdr_format_capacities) & 0xff,
0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, (caddr_t)caps,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
sizeof(struct cdr_format_capacities), ATA_R_READ, 30);
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
}
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_format(device_t dev, struct cdr_format_params* params)
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
{
int8_t ccb[16] = { ATAPI_FORMAT, 0x11, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0 };
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
int error;
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
error = ata_atapicmd(dev, ccb, (u_int8_t *)params,
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
sizeof(struct cdr_format_params), 0, 30);
Add DVD+RW support to the ATA driver and burncd. This also closes PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches included and which I merged with my own work. HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc Enjoy!
2002-08-08 07:59:24 +00:00
return error;
}
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
static int
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
acd_test_ready(device_t dev)
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
{
int8_t ccb[16] = { ATAPI_TEST_UNIT_READY, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
Take newbusification one step further, ie use the device_t more consequently all way through the code down the layers, instead of the mix'n'match that resulted from the conversion done earlier. Sponsored by: pair.com
2005-04-30 16:22:07 +00:00
return ata_atapicmd(dev, ccb, NULL, 0, 0, 30);
This is a major rework of the ATA driver (ATAng) Restructure the way ATA/ATAPI commands are processed, use a common ata_request structure for both. This centralises the way requests are handled so locking is much easier to handle. The driver is now layered much more cleanly to seperate the lowlevel HW access so it can be tailored to specific controllers without touching the upper layers. This is needed to support some of the newer semi-intelligent ATA controllers showing up. The top level drivers (disk, ATAPI devices) are more or less still the same with just corrections to use the new interface. Pull ATA out from under Gaint now that locking can be done in a sane way. Add support for a the National Geode SC1100. Thanks to Soekris engineering for sponsoring a Soekris 4801 to make this support. Fixed alot of small bugs in the chipset code for various chips now we are around in that corner anyways.
2003-08-24 09:22:26 +00:00
}
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
static void
acd_describe(device_t dev)
{
struct ata_channel *ch = device_get_softc(device_get_parent(dev));
struct ata_device *atadev = device_get_softc(dev);
struct acd_softc *cdp = device_get_ivars(dev);
int comma = 0;
char *mechanism;
if (bootverbose) {
device_printf(dev, "<%.40s/%.8s> %s drive at ata%d as %s\n",
atadev->param.model, atadev->param.revision,
(cdp->cap.media & MST_WRITE_DVDR) ? "DVDR" :
(cdp->cap.media & MST_WRITE_DVDRAM) ? "DVDRAM" :
(cdp->cap.media & MST_WRITE_CDRW) ? "CDRW" :
(cdp->cap.media & MST_WRITE_CDR) ? "CDR" :
(cdp->cap.media & MST_READ_DVDROM) ? "DVDROM":"CDROM",
device_get_unit(ch->dev),
(atadev->unit == ATA_MASTER) ? "master" : "slave");
device_printf(dev, "%s", "");
if (cdp->cap.cur_read_speed) {
printf("read %dKB/s", cdp->cap.cur_read_speed * 1000 / 1024);
if (cdp->cap.max_read_speed)
printf(" (%dKB/s)", cdp->cap.max_read_speed * 1000 / 1024);
if ((cdp->cap.cur_write_speed) &&
(cdp->cap.media & (MST_WRITE_CDR | MST_WRITE_CDRW |
MST_WRITE_DVDR | MST_WRITE_DVDRAM))) {
printf(" write %dKB/s", cdp->cap.cur_write_speed * 1000 / 1024);
if (cdp->cap.max_write_speed)
printf(" (%dKB/s)", cdp->cap.max_write_speed * 1000 / 1024);
}
comma = 1;
}
if (cdp->cap.buf_size) {
printf("%s %dKB buffer", comma ? "," : "", cdp->cap.buf_size);
comma = 1;
}
printf("%s %s\n", comma ? "," : "", ata_mode2str(atadev->mode));
device_printf(dev, "Reads:");
comma = 0;
if (cdp->cap.media & MST_READ_CDR) {
printf(" CDR"); comma = 1;
}
if (cdp->cap.media & MST_READ_CDRW) {
printf("%s CDRW", comma ? "," : ""); comma = 1;
}
if (cdp->cap.capabilities & MST_READ_CDDA) {
if (cdp->cap.capabilities & MST_CDDA_STREAM)
printf("%s CDDA stream", comma ? "," : "");
else
printf("%s CDDA", comma ? "," : "");
comma = 1;
}
if (cdp->cap.media & MST_READ_DVDROM) {
printf("%s DVDROM", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_READ_DVDR) {
printf("%s DVDR", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_READ_DVDRAM) {
printf("%s DVDRAM", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_READ_PACKET)
printf("%s packet", comma ? "," : "");
printf("\n");
device_printf(dev, "Writes:");
if (cdp->cap.media & (MST_WRITE_CDR | MST_WRITE_CDRW |
MST_WRITE_DVDR | MST_WRITE_DVDRAM)) {
comma = 0;
if (cdp->cap.media & MST_WRITE_CDR) {
printf(" CDR" ); comma = 1;
}
if (cdp->cap.media & MST_WRITE_CDRW) {
printf("%s CDRW", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_WRITE_DVDR) {
printf("%s DVDR", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_WRITE_DVDRAM) {
printf("%s DVDRAM", comma ? "," : ""); comma = 1;
}
if (cdp->cap.media & MST_WRITE_TEST) {
printf("%s test write", comma ? "," : ""); comma = 1;
}
if (cdp->cap.capabilities & MST_BURNPROOF)
printf("%s burnproof", comma ? "," : "");
}
printf("\n");
if (cdp->cap.capabilities & MST_AUDIO_PLAY) {
device_printf(dev, "Audio: ");
if (cdp->cap.capabilities & MST_AUDIO_PLAY)
printf("play");
if (cdp->cap.max_vol_levels)
printf(", %d volume levels", cdp->cap.max_vol_levels);
printf("\n");
}
device_printf(dev, "Mechanism: ");
switch (cdp->cap.mechanism & MST_MECH_MASK) {
case MST_MECH_CADDY:
mechanism = "caddy"; break;
case MST_MECH_TRAY:
mechanism = "tray"; break;
case MST_MECH_POPUP:
mechanism = "popup"; break;
case MST_MECH_CHANGER:
mechanism = "changer"; break;
case MST_MECH_CARTRIDGE:
mechanism = "cartridge"; break;
default:
mechanism = 0; break;
}
if (mechanism)
printf("%s%s", (cdp->cap.mechanism & MST_EJECT) ?
"ejectable " : "", mechanism);
else if (cdp->cap.mechanism & MST_EJECT)
printf("ejectable");
if (cdp->cap.mechanism & MST_LOCKABLE)
printf((cdp->cap.mechanism & MST_LOCKED) ? ", locked":", unlocked");
if (cdp->cap.mechanism & MST_PREVENT)
printf(", lock protected");
printf("\n");
if ((cdp->cap.mechanism & MST_MECH_MASK) != MST_MECH_CHANGER) {
device_printf(dev, "Medium: ");
switch (cdp->cap.medium_type & MST_TYPE_MASK_HIGH) {
case MST_CDROM:
printf("CD-ROM "); break;
case MST_CDR:
printf("CD-R "); break;
case MST_CDRW:
printf("CD-RW "); break;
case MST_DOOR_OPEN:
printf("door open"); break;
case MST_NO_DISC:
printf("no/blank disc"); break;
case MST_FMT_ERROR:
printf("medium format error"); break;
}
if ((cdp->cap.medium_type & MST_TYPE_MASK_HIGH)<MST_TYPE_MASK_HIGH){
switch (cdp->cap.medium_type & MST_TYPE_MASK_LOW) {
case MST_DATA_120:
printf("120mm data disc"); break;
case MST_AUDIO_120:
printf("120mm audio disc"); break;
case MST_COMB_120:
printf("120mm data/audio disc"); break;
case MST_PHOTO_120:
printf("120mm photo disc"); break;
case MST_DATA_80:
printf("80mm data disc"); break;
case MST_AUDIO_80:
printf("80mm audio disc"); break;
case MST_COMB_80:
printf("80mm data/audio disc"); break;
case MST_PHOTO_80:
printf("80mm photo disc"); break;
case MST_FMT_NONE:
switch (cdp->cap.medium_type & MST_TYPE_MASK_HIGH) {
case MST_CDROM:
printf("unknown"); break;
case MST_CDR:
case MST_CDRW:
printf("blank"); break;
}
break;
default:
printf("unknown (0x%x)", cdp->cap.medium_type); break;
}
}
printf("\n");
}
}
else {
device_printf(dev, "%s ",
(cdp->cap.media & MST_WRITE_DVDR) ? "DVDR" :
(cdp->cap.media & MST_WRITE_DVDRAM) ? "DVDRAM" :
(cdp->cap.media & MST_WRITE_CDRW) ? "CDRW" :
(cdp->cap.media & MST_WRITE_CDR) ? "CDR" :
(cdp->cap.media & MST_READ_DVDROM) ? "DVDROM" :
"CDROM");
if (cdp->changer_info)
printf("with %d CD changer ", cdp->changer_info->slots);
printf("<%.40s/%.8s> at ata%d-%s %s\n",
atadev->param.model, atadev->param.revision,
device_get_unit(ch->dev),
(atadev->unit == ATA_MASTER) ? "master" : "slave",
ata_mode2str(atadev->mode) );
}
}
static device_method_t acd_methods[] = {
/* device interface */
DEVMETHOD(device_probe, acd_probe),
DEVMETHOD(device_attach, acd_attach),
DEVMETHOD(device_detach, acd_detach),
DEVMETHOD(device_shutdown, acd_shutdown),
/* ATA methods */
DEVMETHOD(ata_reinit, acd_reinit),
{ 0, 0 }
};
static driver_t acd_driver = {
"acd",
acd_methods,
Change the ata_* methods to use a channel device instead of a controller device. This helps when there is no controller parent to a channel (PPC port).
2005-03-31 15:05:40 +00:00
0,
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
};
static devclass_t acd_devclass;
static int
acd_modevent(module_t mod, int what, void *arg)
{
Move the creation of ata_channel child devices to the channel code. This allows to attach to the children (ATA devices) even without a driver being attached. This allows atapi-cam to do its work both with and without the pure ATAPI driver being present. ATA patches by /me ATAPI-cam pathes by Thomas
2005-04-15 10:20:52 +00:00
g_modevent(0, what, &acd_class);
This is the much rumoured ATA mkIII update that I've been working on. o ATA is now fully newbus'd and split into modules. This means that on a modern system you just load "atapci and ata" to get the base support, and then one or more of the device subdrivers "atadisk atapicd atapifd atapist ataraid". All can be loaded/unloaded anytime, but for obvious reasons you dont want to unload atadisk when you have mounted filesystems. o The device identify part of the probe has been rewritten to fix the problems with odd devices the old had, and to try to remove so of the long delays some HW could provoke. Also probing is done without the need for interrupts, making earlier probing possible. o SATA devices can be hot inserted/removed and devices will be created/ removed in /dev accordingly. NOTE: only supported on controllers that has this feature: Promise and Silicon Image for now. On other controllers the usual atacontrol detach/attach dance is still needed. o Support for "atomic" composite ATA requests used for RAID. o ATA RAID support has been rewritten and and now supports these metadata formats: "Adaptec HostRAID" "Highpoint V2 RocketRAID" "Highpoint V3 RocketRAID" "Intel MatrixRAID" "Integrated Technology Express" "LSILogic V2 MegaRAID" "LSILogic V3 MegaRAID" "Promise FastTrak" "Silicon Image Medley" "FreeBSD PseudoRAID" o Update the ioctl API to match new RAID levels etc. o Update atacontrol to know about the new RAID levels etc NOTE: you need to recompile atacontrol with the new sys/ata.h, make world will take care of that. NOTE2: that rebuild is done differently from the old system as the rebuild is now done piggybacked on read requests to the array, so atacontrol simply starts a background "dd" to rebuild the array. o The reinit code has been worked over to be much more robust. o The timeout code has been overhauled for races. o Support of new chipsets. o Lots of fixes for bugs found while doing the modulerization and reviewing the old code. Missing or changed features from current ATA: o atapi-cd no longer has support for ATAPI changers. Todays its much cheaper and alot faster to copy those CD images to disk and serve them from there. Besides they dont seem to be made anymore, maybe for that exact reason. o ATA RAID can only read metadata from all the above metadata formats, not write all of them (Promise and Highpoint V2 so far). This means that arrays can be picked up from the BIOS, but they cannot be created from FreeBSD. There is more to it than just the missing write metadata support, those formats are not unique to a given controller like Promise and Highpoint formats, instead they exist for several types, and even worse, some controllers can have different formats and its impossible to tell which one. The outcome is that we cannot reliably create the metadata of those formats and be sure the controller BIOS will understand it. However write support is needed to update/fail/rebuild the arrays properly so it sits fairly high on the TODO list. o So far atapicam is not supported with these changes. When/if this will change is up to the maintainer of atapi-cam so go there for questions. HW donated by: Webveveriet AS HW donated by: Frode Nordahl HW donated by: Yahoo! HW donated by: Sentex Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
return 0;
}
DRIVER_MODULE(acd, ata, acd_driver, acd_devclass, acd_modevent, NULL);
MODULE_VERSION(acd, 1);
MODULE_DEPEND(acd, ata, 1, 1, 1);
Reference in New Issue Copy Permalink