freebsd-skq/sys/dev/ahb/ahbreg.h

284 lines
7.5 KiB
C
Raw Normal View History

/*
* Hardware structure definitions for the Adaptec 174X CAM SCSI device driver.
*
* Copyright (c) 1998 Justin T. Gibbs
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice immediately at the beginning of the file, without modification,
* this list of conditions, and the following disclaimer.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
1999-08-28 01:08:13 +00:00
* $FreeBSD$
*/
/* Resource Constatns */
#define AHB_NECB 64
#define AHB_NSEG 32
/* AHA1740 EISA ID, IO port range size, and offset from slot base */
#define EISA_DEVICE_ID_ADAPTEC_1740 0x04900000
#define AHB_EISA_IOSIZE 0x100
#define AHB_EISA_SLOT_OFFSET 0xc00
/* AHA1740 EISA board control registers (Offset from slot base) */
#define EBCTRL 0x084
#define CDEN 0x01
/*
* AHA1740 EISA board mode registers (Offset from slot base)
*/
#define PORTADDR 0x0C0
#define PORTADDR_ENHANCED 0x80
#define BIOSADDR 0x0C1
#define INTDEF 0x0C2
#define INT9 0x00
#define INT10 0x01
#define INT11 0x02
#define INT12 0x03
#define INT14 0x05
#define INT15 0x06
#define INTLEVEL 0x08
#define INTEN 0x10
#define SCSIDEF 0x0C3
#define HSCSIID 0x0F /* our SCSI ID */
#define RSTBUS 0x10
#define BUSDEF 0x0C4
#define B0uS 0x00 /* give up bus immediatly */
#define B4uS 0x01 /* delay 4uSec. */
#define B8uS 0x02 /* delay 8uSec. */
#define RESV0 0x0C5
#define RESV1 0x0C6
#define EXTENDED_TRANS 0x01
#define RESV2 0x0C7
/*
* AHA1740 ENHANCED mode mailbox control regs (Offset from slot base)
*/
#define MBOXOUT0 0x0D0
#define MBOXOUT1 0x0D1
#define MBOXOUT2 0x0D2
#define MBOXOUT3 0x0D3
#define ATTN 0x0D4
#define ATTN_TARGMASK 0x0F
#define ATTN_IMMED 0x10
#define ATTN_STARTECB 0x40
#define ATTN_ABORTECB 0x50
#define ATTN_TARG_RESET 0x80
#define CONTROL 0x0D5
#define CNTRL_SET_HRDY 0x20
#define CNTRL_CLRINT 0x40
#define CNTRL_HARD_RST 0x80
#define INTSTAT 0x0D6
#define INTSTAT_TARGET_MASK 0x0F
#define INTSTAT_MASK 0xF0
#define INTSTAT_ECB_OK 0x10 /* ECB Completed w/out error */
#define INTSTAT_ECB_CMPWRETRY 0x50 /* ECB Completed w/retries */
#define INTSTAT_HW_ERR 0x70 /* Adapter Hardware Failure */
#define INTSTAT_IMMED_OK 0xA0 /* Immediate command complete */
#define INTSTAT_ECB_CMPWERR 0xC0 /* ECB Completed w/error */
#define INTSTAT_AEN_OCCURED 0xD0 /* Async Event Notification */
#define INTSTAT_IMMED_ERR 0xE0 /* Immediate command failed */
#define HOSTSTAT 0x0D7
#define HOSTSTAT_MBOX_EMPTY 0x04
#define HOSTSTAT_INTPEND 0x02
#define HOSTSTAT_BUSY 0x01
#define MBOXIN0 0x0D8
#define MBOXIN1 0x0D9
#define MBOXIN2 0x0DA
#define MBOXIN3 0x0DB
#define STATUS2 0x0DC
#define STATUS2_HOST_READY 0x01
typedef enum {
IMMED_RESET = 0x000080,
IMMED_DEVICE_CLEAR_QUEUE = 0x000480,
IMMED_ADAPTER_CLEAR_QUEUE = 0x000880,
IMMED_RESUME = 0x200090
} immed_cmd;
struct ecb_status {
/* Status Flags */
u_int16_t no_error :1, /* Completed with no error */
data_underrun :1,
:1,
ha_queue_full :1,
spec_check :1,
data_overrun :1,
chain_halted :1,
intr_issued :1,
status_avail :1, /* status bytes 14-31 are valid */
sense_stored :1,
:1,
init_requied :1,
major_error :1,
:1,
extended_ca :1,
:1;
/* Host Status */
u_int8_t ha_status;
u_int8_t scsi_status;
int32_t resid_count;
u_int32_t resid_addr;
u_int16_t addit_status;
u_int8_t sense_len;
u_int8_t unused[9];
u_int8_t cdb[6];
};
typedef enum {
HS_OK = 0x00,
HS_CMD_ABORTED_HOST = 0x04,
HS_CMD_ABORTED_ADAPTER = 0x05,
HS_FIRMWARE_LOAD_REQ = 0x08,
HS_TARGET_NOT_ASSIGNED = 0x0A,
HS_SEL_TIMEOUT = 0x11,
HS_DATA_RUN_ERR = 0x12,
HS_UNEXPECTED_BUSFREE = 0x13,
HS_INVALID_PHASE = 0x14,
HS_INVALID_OPCODE = 0x16,
HS_INVALID_CMD_LINK = 0x17,
HS_INVALID_ECB_PARAM = 0x18,
HS_DUP_TCB_RECEIVED = 0x19,
HS_REQUEST_SENSE_FAILED = 0x1A,
HS_TAG_MSG_REJECTED = 0x1C,
HS_HARDWARE_ERR = 0x20,
HS_ATN_TARGET_FAILED = 0x21,
HS_SCSI_RESET_ADAPTER = 0x22,
HS_SCSI_RESET_INCOMING = 0x23,
HS_PROGRAM_CKSUM_ERROR = 0x80
} host_status;
typedef enum {
ECBOP_NOP = 0x00,
ECBOP_INITIATOR_SCSI_CMD = 0x01,
ECBOP_RUN_DIAGNOSTICS = 0x05,
ECBOP_INITIALIZE_SCSI = 0x06, /* Set syncrate/disc/parity */
ECBOP_READ_SENSE = 0x08,
ECBOP_DOWNLOAD_FIRMWARE = 0x09,
ECBOP_READ_HA_INQDATA = 0x0a,
ECBOP_TARGET_SCSI_CMD = 0x10
} ecb_op;
struct ha_inquiry_data {
struct scsi_inquiry_data scsi_data;
u_int8_t release_date[8];
u_int8_t release_time[8];
u_int16_t firmware_cksum;
u_int16_t reserved;
u_int16_t target_data[16];
};
struct hardware_ecb {
u_int16_t opcode;
u_int16_t flag_word1;
#define FW1_LINKED_CMD 0x0001
#define FW1_DISABLE_INTR 0x0080
#define FW1_SUPPRESS_URUN_ERR 0x0400
#define FW1_SG_ECB 0x1000
#define FW1_ERR_STATUS_BLK_ONLY 0x4000
#define FW1_AUTO_REQUEST_SENSE 0x8000
u_int16_t flag_word2;
#define FW2_LUN_MASK 0x0007
#define FW2_TAG_ENB 0x0008
#define FW2_TAG_TYPE 0x0030
#define FW2_TAG_TYPE_SHIFT 4
#define FW2_DISABLE_DISC 0x0040
#define FW2_CHECK_DATA_DIR 0x0100
#define FW2_DATA_DIR_IN 0x0200
#define FW2_SUPRESS_TRANSFER 0x0400
#define FW2_CALC_CKSUM 0x0800
#define FW2_RECOVERY_ECB 0x4000
#define FW2_NO_RETRY_ON_BUSY 0x8000
u_int16_t reserved;
u_int32_t data_ptr;
u_int32_t data_len;
u_int32_t status_ptr;
u_int32_t link_ptr;
u_int32_t reserved2;
u_int32_t sense_ptr;
u_int8_t sense_len;
u_int8_t cdb_len;
u_int16_t cksum;
u_int8_t cdb[12];
};
typedef struct {
u_int32_t addr;
u_int32_t len;
} ahb_sg_t;
typedef enum {
ECB_FREE = 0x0,
ECB_ACTIVE = 0x1,
ECB_DEVICE_RESET = 0x2,
ECB_SCSIBUS_RESET = 0x4,
ECB_RELEASE_SIMQ = 0x8
} ecb_state;
struct ecb {
struct hardware_ecb hecb;
struct ecb_status status;
struct scsi_sense_data sense;
ahb_sg_t sg_list[AHB_NSEG];
SLIST_ENTRY(ecb) links;
ecb_state state;
union ccb *ccb;
bus_dmamap_t dmamap;
};
struct ahb_softc {
bus_space_tag_t tag;
bus_space_handle_t bsh;
struct cam_sim *sim;
struct cam_path *path;
SLIST_HEAD(,ecb) free_ecbs;
LIST_HEAD(,ccb_hdr) pending_ccbs;
struct ecb *ecb_array;
u_int32_t ecb_physbase;
bus_dma_tag_t buffer_dmat; /* dmat for buffer I/O */
bus_dma_tag_t ecb_dmat; /* dmat for our ecb array */
bus_dmamap_t ecb_dmamap;
volatile u_int32_t immed_cmd;
struct ecb *immed_ecb;
struct ha_inquiry_data *ha_inq_data;
u_int32_t ha_inq_physbase;
u_long unit;
u_int init_level;
u_int scsi_id;
u_int num_ecbs;
u_int extended_trans;
u_int8_t disc_permitted;
u_int8_t tags_permitted;
};