freebsd-skq/sys/dev/mii/acphyreg.h

78 lines
3.3 KiB
C
Raw Normal View History

/*-
* Copyright (c) 2001 Semen Ustimenko (semenu@FreeBSD.org)
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _DEV_MII_ACPHYREG_H_
#define _DEV_MII_ACPHYREG_H_
/*
* Register definitions for the Altima Communications AC101
*/
#define MII_ACPHY_POL 0x10 /* Polarity int level */
/* High byte is interrupt mask register */
#define MII_ACPHY_INT 0x11 /* Interrupt control/status */
#define AC_INT_ACOMP 0x0001 /* Autoneg complete */
#define AC_INT_REM_FLT 0x0002 /* Remote fault */
#define AC_INT_LINK_DOWN 0x0004 /* Link not OK */
#define AC_INT_LP_ACK 0x0008 /* FLP ack recved */
#define AC_INT_PD_FLT 0x0010 /* Parallel detect fault */
#define AC_INT_PAGE_RECV 0x0020 /* New page recved */
#define AC_INT_RX_ER 0x0040 /* RX_ER transitions high */
#define AC_INT_JAB 0x0080 /* Jabber detected */
#define MII_ACPHY_DIAG 0x12 /* Diagnostic */
#define AC_DIAG_RX_LOCK 0x0100
#define AC_DIAG_RX_PASS 0x0200
#define AC_DIAG_SPEED 0x0400 /* Aneg speed result */
#define AC_DIAG_DUPLEX 0x0800 /* Aneg duplex result */
#define MII_ACPHY_PWRLOOP 0x13 /* Power/Loopback */
#define MII_ACPHY_CBLMEAS 0x14 /* Cable meas. */
#define MII_ACPHY_MCTL 0x15 /* Mode control */
#define AC_MCTL_FX_SEL 0x0001 /* FX mode */
#define AC_MCTL_BYP_PCS 0x0002 /* Bypass PCS */
#define AC_MCTL_SCRMBL 0x0004 /* Data scrambling */
#define AC_MCTL_REM_LOOP 0x0008 /* Remote loopback */
#define AC_MCTL_DIS_WDT 0x0010 /* Disable watchdog timer */
#define AC_MCTL_DIS_REC 0x0020 /* Disable recv error counter */
#define AC_MCTL_REC_FULL 0x0040 /* Recv error counter full */
#define AC_MCTL_FRC_FEF 0x0080 /* Force Far End Fault Insert. */
#define AC_MCTL_DIS_FEF 0x0100 /* Disable FEF Insertion */
#define AC_MCTL_LED_SEL 0x0200 /* Compat LED config */
#define AC_MCTL_ALED_SEL 0x0400 /* ActLED RX&TX - RX only */
#define AC_MCTL_10BT_SEL 0x0800 /* Enable 7-wire interface */
#define AC_MCTL_DIS_JAB 0x1000 /* Disable jabber */
#define AC_MCTL_FRC_LINK 0x2000 /* Force TX link up */
#define AC_MCTL_DIS_NLP 0x4000 /* Disable NLP check */
#define MII_ACPHY_REC 0x18 /* Recv error counter */
#endif /* _DEV_MII_ACPHYREG_H_ */