2013-03-28 20:48:58 +00:00
|
|
|
#
|
|
|
|
|
# This file adds to the values in AR91XX_BASE.hints.
|
|
|
|
|
#
|
|
|
|
|
# $FreeBSD$
|
|
|
|
|
|
2013-04-05 01:38:13 +00:00
|
|
|
# mdiobus on arge1
|
|
|
|
|
hint.argemdio.0.at="nexus0"
|
|
|
|
|
hint.argemdio.0.maddr=0x1a000000
|
|
|
|
|
hint.argemdio.0.msize=0x1000
|
|
|
|
|
hint.argemdio.0.order=0
|
|
|
|
|
|
|
|
|
|
# Embedded Atheros Switch
|
|
|
|
|
hint.arswitch.0.at="mdio0"
|
|
|
|
|
hint.arswitch.0.is_7240=1
|
|
|
|
|
hint.arswitch.0.numphys=4
|
|
|
|
|
hint.arswitch.0.phy4cpu=1 # phy 4 is a "CPU" separate PHY
|
|
|
|
|
hint.arswitch.0.is_rgmii=0
|
|
|
|
|
hint.arswitch.0.is_gmii=1 # arge1 <-> switch PHY is GMII
|
|
|
|
|
|
|
|
|
|
# arge0 - MII, autoneg, phy(4)
|
|
|
|
|
hint.arge.0.phymask=0x10 # PHY4
|
|
|
|
|
hint.arge.0.mdio=mdioproxy1 # .. off of the switch mdiobus
|
|
|
|
|
|
|
|
|
|
# arge1 - GMII, 1000/full
|
|
|
|
|
hint.arge.1.phymask=0x0 # No directly mapped PHYs
|
|
|
|
|
hint.arge.1.media=1000
|
|
|
|
|
hint.arge.1.fduplex=1
|
2013-03-28 20:48:58 +00:00
|
|
|
|
|
|
|
|
# The AP121 4MB flash layout:
|
|
|
|
|
#
|
|
|
|
|
# bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs
|
|
|
|
|
# init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),
|
|
|
|
|
# 2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
|
|
|
|
|
#
|
|
|
|
|
# So:
|
|
|
|
|
# 256k: uboot
|
|
|
|
|
# 64: uboot-env
|
|
|
|
|
# 2752k: rootfs
|
|
|
|
|
# 896k: kernel
|
|
|
|
|
# 64k: config
|
|
|
|
|
# 64k: ART
|
|
|
|
|
|
|
|
|
|
hint.map.0.at="flash/spi0"
|
|
|
|
|
hint.map.0.start=0x00000000
|
|
|
|
|
hint.map.0.end=0x000040000
|
|
|
|
|
hint.map.0.name="uboot"
|
|
|
|
|
hint.map.0.readonly=1
|
|
|
|
|
|
|
|
|
|
hint.map.1.at="flash/spi0"
|
|
|
|
|
hint.map.1.start=0x00040000
|
|
|
|
|
hint.map.1.end=0x00050000
|
|
|
|
|
hint.map.1.name="uboot-env"
|
|
|
|
|
hint.map.1.readonly=0
|
|
|
|
|
|
|
|
|
|
hint.map.2.at="flash/spi0"
|
|
|
|
|
hint.map.2.start=0x00050000
|
|
|
|
|
hint.map.2.end=0x00300000
|
|
|
|
|
hint.map.2.name="rootfs"
|
|
|
|
|
hint.map.2.readonly=0
|
|
|
|
|
|
|
|
|
|
hint.map.3.at="flash/spi0"
|
|
|
|
|
hint.map.3.start=0x00300000
|
|
|
|
|
hint.map.3.end=0x003e0000
|
|
|
|
|
hint.map.3.name="kernel"
|
|
|
|
|
hint.map.3.readonly=0
|
|
|
|
|
|
|
|
|
|
hint.map.4.at="flash/spi0"
|
|
|
|
|
hint.map.4.start=0x003e0000
|
|
|
|
|
hint.map.4.end=0x003f0000
|
|
|
|
|
hint.map.4.name="cfg"
|
|
|
|
|
hint.map.4.readonly=0
|
|
|
|
|
|
|
|
|
|
# This is radio calibration section. It is (or should be!) unique
|
|
|
|
|
# for each board, to take into account thermal and electrical differences
|
|
|
|
|
# as well as the regulatory compliance data.
|
|
|
|
|
#
|
|
|
|
|
hint.map.5.at="flash/spi0"
|
|
|
|
|
hint.map.5.start=0x003f0000
|
|
|
|
|
hint.map.5.end=0x00400000
|
|
|
|
|
hint.map.5.name="art"
|
|
|
|
|
hint.map.5.readonly=1
|
|
|
|
|
|
|
|
|
|
# GPIO specific configuration block
|
|
|
|
|
|
|
|
|
|
# Don't flip on anything that isn't already enabled.
|
|
|
|
|
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
|
|
|
|
|
# not used here.
|
2013-04-05 02:15:10 +00:00
|
|
|
hint.gpio.0.function_set=0x00000000
|
2013-03-28 20:48:58 +00:00
|
|
|
hint.gpio.0.function_clear=0x00000000
|
|
|
|
|
|
|
|
|
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
|
|
|
|
#hint.gpio.0.pinmask=0x001c02ae
|
2013-04-05 02:15:10 +00:00
|
|
|
hint.gpio.0.pinmask=0x00001803
|
2013-03-28 20:48:58 +00:00
|
|
|
|
2013-04-05 02:15:10 +00:00
|
|
|
# gpio0 - WLAN LED
|
|
|
|
|
# gpio1 - USB LED
|
|
|
|
|
# gpio11 - Jumpstart button
|
|
|
|
|
# gpio12 - Reset button
|
2013-03-28 20:48:58 +00:00
|
|
|
|
2013-04-05 02:15:10 +00:00
|
|
|
# LEDs are configured separately and driven by the LED device
|
|
|
|
|
hint.gpioled.0.at="gpiobus0"
|
|
|
|
|
hint.gpioled.0.name="wlan"
|
|
|
|
|
hint.gpioled.0.pins=0x0001
|
2013-03-28 20:48:58 +00:00
|
|
|
|
2013-04-05 02:15:10 +00:00
|
|
|
hint.gpioled.1.at="gpiobus0"
|
|
|
|
|
hint.gpioled.1.name="usb"
|
|
|
|
|
hint.gpioled.1.pins=0x0002
|
