Add kernel support for the TP-LINK MR3020 Atheros MIPS 24k router.
AR9331 based system. Phabric: https://reviews.freebsd.org/D780 Reviewed by: adrian
This commit is contained in:
sbruno
parent
e58ee21a5e
commit
0d3437c89c
65
sys/mips/conf/TP-MR3020
Normal file
65
sys/mips/conf/TP-MR3020
Normal file
@ -0,0 +1,65 @@
|
|||||||
|
#
|
||||||
|
# TP Link MR3020 - an AR9331 based SoC wifi device.
|
||||||
|
#
|
||||||
|
# This is for the 32 RAM/4 flash part. There is little to no
|
||||||
|
# chance that this will ever boot FreeBSD directly from the 3.5MB
|
||||||
|
# of flash. The kernel can fit into the space, but userland is just
|
||||||
|
# too big even when stripped down to its limits.
|
||||||
|
#
|
||||||
|
# * AR9331 SoC
|
||||||
|
# * 32MB RAM
|
||||||
|
# * 4MB flash
|
||||||
|
# * Integrated 1x1 2GHz wifi and 10/100 bridge
|
||||||
|
# * USB powered
|
||||||
|
# * USB storage
|
||||||
|
#
|
||||||
|
# $FreeBSD$
|
||||||
|
#
|
||||||
|
|
||||||
|
# Include the default AR933x parameters
|
||||||
|
include "AR933X_BASE"
|
||||||
|
|
||||||
|
ident TP-MR3020
|
||||||
|
|
||||||
|
# Override hints with board values
|
||||||
|
hints "TP-MR3020.hints"
|
||||||
|
|
||||||
|
# Board memory - 32MB
|
||||||
|
options AR71XX_REALMEM=(32*1024*1024)
|
||||||
|
|
||||||
|
# i2c GPIO bus
|
||||||
|
device gpioiic
|
||||||
|
device iicbb
|
||||||
|
device iicbus
|
||||||
|
device iic
|
||||||
|
|
||||||
|
# Options required for miiproxy and mdiobus
|
||||||
|
options ARGE_MDIO # Export an MDIO bus separate from arge
|
||||||
|
device miiproxy # MDIO bus <-> MII PHY rendezvous
|
||||||
|
|
||||||
|
device etherswitch
|
||||||
|
device arswitch
|
||||||
|
|
||||||
|
# Enable the uboot environment stuff rather then the
|
||||||
|
# redboot stuff.
|
||||||
|
options AR71XX_ENV_UBOOT
|
||||||
|
|
||||||
|
# uzip - to boot natively from flash
|
||||||
|
device geom_uncompress
|
||||||
|
|
||||||
|
# Used for the static uboot partition map
|
||||||
|
device geom_map
|
||||||
|
|
||||||
|
# Boot off of the rootfs, as defined in the geom_map setup.
|
||||||
|
# Probably, this should be a USB device as the memory available
|
||||||
|
# compressed rootfs is simply too small for FreeBSD
|
||||||
|
#options ROOTDEVNAME=\"ufs:map/rootfs.uncompress\"
|
||||||
|
|
||||||
|
# Boot off of a uboot tftp ramdisk kernel image. Because the flash
|
||||||
|
# on this unit is so small, this is the only way to do dev work.
|
||||||
|
# For full deployment, you will *have* to use a usb storage device
|
||||||
|
# as a rootfs and use the flash to hold the kernel only.
|
||||||
|
options MD_ROOT # md device usable as a potential root device
|
||||||
|
options MD_ROOT_SIZE=10240
|
||||||
|
makeoptions MFS_IMAGE=/tftpboot/mfsroot-tl-mr3020.img.ulzma
|
||||||
|
options ROOTDEVNAME=\"ufs:md0.uncompress\"
|
||||||
101
sys/mips/conf/TP-MR3020.hints
Normal file
101
sys/mips/conf/TP-MR3020.hints
Normal file
@ -0,0 +1,101 @@
|
|||||||
|
#
|
||||||
|
# This file adds to the values in AR933X_BASE.hints
|
||||||
|
#
|
||||||
|
# $FreeBSD$
|
||||||
|
|
||||||
|
# mdiobus on arge1
|
||||||
|
hint.argemdio.0.at="nexus0"
|
||||||
|
hint.argemdio.0.maddr=0x1a000000
|
||||||
|
hint.argemdio.0.msize=0x1000
|
||||||
|
hint.argemdio.0.order=0
|
||||||
|
|
||||||
|
# There's no need to set the ar933x GMAC configuration bits.
|
||||||
|
# This just creates a switch instance and correctly uses it.
|
||||||
|
|
||||||
|
# Embedded Atheros Switch
|
||||||
|
hint.arswitch.0.at="mdio0"
|
||||||
|
|
||||||
|
# XXX this should really say it's an AR933x switch, as there
|
||||||
|
# are some vlan specific differences here!
|
||||||
|
hint.arswitch.0.is_7240=1
|
||||||
|
hint.arswitch.0.numphys=4
|
||||||
|
hint.arswitch.0.phy4cpu=1 # phy 4 is a "CPU" separate PHY
|
||||||
|
hint.arswitch.0.is_rgmii=0
|
||||||
|
hint.arswitch.0.is_gmii=1 # arge1 <-> switch PHY is GMII
|
||||||
|
|
||||||
|
# arge0 - MII, autoneg, phy(4)
|
||||||
|
hint.arge.0.phymask=0x10 # PHY4
|
||||||
|
hint.arge.0.mdio=mdioproxy1 # .. off of the switch mdiobus
|
||||||
|
|
||||||
|
# arge1 - GMII, 1000/full
|
||||||
|
hint.arge.1.phymask=0x0 # No directly mapped PHYs
|
||||||
|
hint.arge.1.media=1000
|
||||||
|
hint.arge.1.fduplex=1
|
||||||
|
|
||||||
|
# Where the ART is - last 64k in the flash
|
||||||
|
# 0x9fff1000 ?
|
||||||
|
hint.ath.0.eepromaddr=0x1fff0000
|
||||||
|
hint.ath.0.eepromsize=16384
|
||||||
|
|
||||||
|
# The board 16MiB flash layout in uboot env:
|
||||||
|
#
|
||||||
|
# 256k(u-boot),64k(u-boot-env),2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
|
||||||
|
|
||||||
|
# However, it boots from 0x9f050000, which is the front of the flsah!
|
||||||
|
# Thus the kernel/rootfs are switched around.
|
||||||
|
|
||||||
|
# 256KB
|
||||||
|
hint.map.0.at="flash/spi0"
|
||||||
|
hint.map.0.start=0x00000000
|
||||||
|
hint.map.0.end=0x00040000
|
||||||
|
hint.map.0.name="uboot"
|
||||||
|
hint.map.0.readonly=1
|
||||||
|
|
||||||
|
# 64KB
|
||||||
|
hint.map.1.at="flash/spi0"
|
||||||
|
hint.map.1.start=0x00040000
|
||||||
|
hint.map.1.end=0x00050000
|
||||||
|
hint.map.1.name="uboot-env"
|
||||||
|
hint.map.1.readonly=0
|
||||||
|
|
||||||
|
# 2752KB
|
||||||
|
hint.map.2.at="flash/spi0"
|
||||||
|
hint.map.2.start=0x00050000
|
||||||
|
hint.map.2.end="search:0x00100000:0x10000:.!/bin/sh"
|
||||||
|
hint.map.2.name="kernel"
|
||||||
|
hint.map.2.readonly=0
|
||||||
|
|
||||||
|
# 896KB
|
||||||
|
hint.map.3.at="flash/spi0"
|
||||||
|
hint.map.3.start="search:0x00100000:0x10000:.!/bin/sh"
|
||||||
|
hint.map.3.end=0x003e0000
|
||||||
|
hint.map.3.name="rootfs"
|
||||||
|
hint.map.3.readonly=0
|
||||||
|
|
||||||
|
# 64K NVRAM
|
||||||
|
hint.map.4.at="flash/spi0"
|
||||||
|
hint.map.4.start=0x003e0000
|
||||||
|
hint.map.4.end=0x003f0000
|
||||||
|
hint.map.4.name="cfg"
|
||||||
|
hint.map.4.readonly=0
|
||||||
|
|
||||||
|
# 64K ART
|
||||||
|
hint.map.5.at="flash/spi0"
|
||||||
|
hint.map.5.start=0x003f0000
|
||||||
|
hint.map.5.end=0x00400000
|
||||||
|
hint.map.5.name="art"
|
||||||
|
hint.map.5.readonly=1
|
||||||
|
|
||||||
|
# GPIO specific configuration block
|
||||||
|
|
||||||
|
# Don't flip on anything that isn't already enabled.
|
||||||
|
# This includes leaving the SPI CS1/CS2 pins as GPIO pins as they're
|
||||||
|
# not used here.
|
||||||
|
hint.gpio.0.function_set=0x00000000
|
||||||
|
hint.gpio.0.function_clear=0x00000000
|
||||||
|
|
||||||
|
# These are the GPIO LEDs and buttons which can be software controlled.
|
||||||
|
#hint.gpio.0.pinmask=0x001c02ae
|
||||||
|
#hint.gpio.0.pinmask=0x00001803
|
||||||
|
|
||||||
|
# XXX TODO: the button and LEDs!
|
||||||
Loading…
Reference in New Issue
Block a user